Alliance Laundry Systems F232157R7 Users Manual Programming For Washer Extractors

F232157R7 F232157

f232157r7 2ac16b75-3126-40e1-9d06-2195f33f017a Alliance Laundry Systems Washer F232157R7 User Guide |

2015-02-05

: Alliance-Laundry-Systems Alliance-Laundry-Systems-F232157R7-Users-Manual-506555 alliance-laundry-systems-f232157r7-users-manual-506555 alliance-laundry-systems pdf

Open the PDF directly: View PDF PDF.
Page Count: 36

DownloadAlliance-Laundry-Systems Alliance-Laundry-Systems-F232157R7-Users-Manual- Programming For Washer-Extractors  Alliance-laundry-systems-f232157r7-users-manual
Open PDF In BrowserView PDF
Programming

Washer-Extractors
Cabinet Hardmount

B-Series Microcomputer for Coin Models
2 Speed and Variable-Speed
Refer to Page 7 for Model Identification

NORMAL

WASH
ADD
BLEACH

HOT

WARM

NORMAL

PERM PRESS

RINSE
SPIN

PERM PRESS

WARM

COLD

QUICK WASH

QUICK WASH

START

DOOR

HOT

WARM

HEAVY SOIL

DELICATE

HOT

COLD

DOMESTIC MODELS

CHM4
CHM482R

95C

95C

60C

60C

40C

40C

30C
<

<

INTERNATIONAL MODELS

CHM488R
CHM488R

Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)

www.comlaundry.com

Part No. F232157R7
August 2009

Table of
Contents

Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
Safety Decals ........................................................................................
Operator Safety.....................................................................................

3
3
3
5
6

Introduction......................................................................................... 7
Model Identification......................................................................... 7
Nameplate Location.............................................................................. 8
Replacement Parts ................................................................................ 8
Customer Service.................................................................................. 8
Electronic Control Unit......................................................................... 9
Control Output Fuse Board................................................................... 9
Summary of Control Outputs and Inputs.............................................. 9
Outputs ............................................................................................. 9
Inputs................................................................................................ 9
Control Voltage................................................................................ 9
Harnessing........................................................................................ 9
Communications ................................................................................... 10
Central Pay System .......................................................................... 10
Third Party Card Reader .................................................................. 10
Programming ......................................................................................
Entering Program Mode .......................................................................
Determining Firmware ID Code...........................................................
Programming Vend Price
(For Models with Firmware ID Code “C2HL” and “CuHL”)............
Setup Mode ......................................................................................
Cycle and Error Count ..........................................................................
Cycle and Error Count addition............................................................
Programming Cycle Segments.........................................................
Programming Vend Price
(For Earlier Models)...........................................................................
Setup Mode ......................................................................................
Cycle and Error Count ..........................................................................
Programming Cycle Segments.........................................................
Options for Each Segment ....................................................................
To Edit an Entire Wash Cycle Formula................................................
Wash 1 – Wash 4 .............................................................................
Rinse 1 – Rinse 4 .............................................................................
Abnormal Conditions............................................................................
Door Will Not Lock .........................................................................
Door Open During Operation ..........................................................
Excessive Fill Time..........................................................................
Out-of-Balance.................................................................................
Drain Error (For Models With Firmware ID Code “C2HL” and
“CuHL”) .........................................................................................
Clogged Filter (All C80 and C60 X Voltage ONLY Models).........
Door Will Not Unlock .....................................................................
On Board Battery Problem...............................................................

12
12
12
13
13
14
14
14
15
15
16
16
18
24
24
25
26
26
26
26
26
27
27
27
27

© Copyright 2009, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

1

Temperature Probe Malfunction ......................................................
Rapid Advance (For Models With Firmware ID Code “C2HL” and
“CuHL”) .............................................................................................
Enabling Rapid Advance .................................................................
How to Rapid Advance During All Steps
(Except First Fill Step).....................................................................
How to Rapid Advance (During First Fill Step) ..............................
Temporary Free Mode ..........................................................................
Test Cycle .............................................................................................
Permanent Factory Diagnostic Test Cycle ...........................................
Cycle Charts..........................................................................................

2

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

27
27
27
27
27
28
28
29
31

F232157

Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.

DANGER
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.

WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.

CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
IMPORTANT: The word “NOTE” is used to
communicate installation, operation, maintenance
or servicing information that is important but not
hazard related.

Important Safety Instructions

WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023

1. Read all instructions before using the washer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, drycleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas
is flammable; do not smoke or use an open flame
during this time.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

3

Safety Information

9. Do not install or store the washer where it will be
exposed to water and/or weather.
10. Do not tamper with the controls.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
13. Use washer only for its intended purpose,
washing textiles.
14. Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
16. Install the washer according to the installation
instructions. All connections for water, drain,
electrical power and grounding must comply
with local codes and be made by licensed
personnel when required.

20. If the supply cord is damaged, it must be replaced
by a special cord or assembly available from the
manufacturer or its service agent.
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open.
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
24. Always follow the fabric care instructions
supplied by the textile manufacturer.
25. Never operate the washer with any guards and/or
panels removed.
26. DO NOT operate the washer with missing or
broken parts.
27. DO NOT bypass any safety devices.
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.

17. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc. or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.

NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.

18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.

Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.

19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a
qualified service person.

4

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Safety Information

WARNING

CAUTION

This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
damage, and may void the warranty.
SW004

IMPORTANT: Ensure that the recommended
clearances for inspection and maintenance
are provided. Never allow the inspection and
maintenance space to be blocked.

Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
SW025

WARNING
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
the pipe can be touched.
SW014

WARNING
Install the machine on a level floor of
sufficient strength. Failure to do so may
result in conditions which can produce
serious injury, death and/or property
damage.
W703

Safety Decals
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the
manufacturer immediately.
Use manufacturer-authorized spare parts to avoid
safety hazards.

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

5

Safety Information

Operator Safety

Do not bypass any safety devices in the machine.

WARNING

WARNING

NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012

To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:

Never operate the machine with a
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
damage.
SW039

1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.

6

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Introduction
Model Identification
Information in this manual is applicable
to these models:
HC20BC2

HC30BY2

HC60BXF

SC20BX2

SC40BL2

SC60BYF

HC20BL2

HC40BC2

HC60BYF

SC20BY2

SC40BX2

SC60BY2

HC20BX2

HC40BL2

HC60BY2

SC25BC2

SC40BY2

SC80BCV

HC20BY2

HC40BX2

HC80BCV

SC25BL2

SC50BC2

SC80BLV

HC25BC2

HC40BY2

HC80BLV

SC25BX2

SC50BY2

SC80BXV

HC25BL2

HC50BC2

HC80BXV

SC25BY2

SC60BC2

SC80BYV

HC25BX2

HC50BY2

HC80BYV

SC30BC2

SC60BCF

SC125BCV

HC25BY2

HC60BC2

HC125BCV

SC30BL2

SC60BL2

SC125BYV

HC30BC2

HC60BCF

HC125BYV

SC30BX2

SC60BLF

HC30BL2

HC60BLF

SC20BC2

SC30BY2

SC60BX2

HC30BX2

HC60BX2

SC20BL2

SC40BC2

SC60BXF

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

7

Introduction

Nameplate Location

Replacement Parts

The nameplate is located at the rear of the machine and
inside door. Always provide the machine’s serial
number and model number when ordering parts or
when seeking technical assistance.

If literature or replacement parts are required, contact
the source from whom the machine was purchased or
contact Alliance Laundry Systems at (920) 748-3950
for the name and address of the nearest authorized
parts distributor.

1

Customer Service
For technical assistance, call (920) 748-3121
Ripon, Wisconsin.

CHM167R

CHM167R

1

Nameplate

Figure 1

8

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Introduction

Electronic Control Unit

7. Supply 2 (bleach) (S2)

The “B” electronic control is composed of the
electronic control unit and the control fuse board with
wiring harness. Only an authorized person should look
inside the control compartment. First TURN OFF
POWER, open lid and remove any cover present.
Make sure door lock circuit has fully discharged. The
door unlock capacitor can retain high electrical charge,
even when the machine’s electrical inputs are
disconnected, until it has discharged. Some machines
are equipped with an orange or red indicator light
facing upward in the control compartment. If this is
on, wait until light goes off (indicating when high
voltage in the door lock circuit has discharged). The
components are described below.

8. Supply 3 (sour/softener) (S3)

This portion of the control contains the “intelligence” –
the micro-controller and the miscellaneous components
on the printed circuit (PC) board. The board has a
metal cover, which MUST be in place at all times
during machine operation. Operation of the machine
without this cover installed will void the warranty.
The control unit monitors and responds to input, gives
information about the status of the washer and
monitors and responds to inputs from the user
interface (keypad). The control provides signals to the
control output unit, which in turn operates the
components that control the machine functions. This is
located behind the machine control panel.

Control Output Fuse Board
This portion of the control contains the power supply
for the control unit, and also the switching devices
which power the components in the machine, all of
which are on the output PC board. The switching
devices are controlled by the control unit, and are solid
state.

9. Optional 3rd (Extra) Fill Inlet (governed by the
configuration settings) (S4)
10. Optional Heat (HT)
11. *Prep for Card Reader or Central Pay (“machine
available signal”)
For standard models, the components for outputs
shown as “optional” will not be populated on the
output printed circuit board.
AC outputs are solid state outputs that operate either
120 Volt AC or 220 Volt AC (nominal voltage)
components, depending on the control voltage
configuration. Outputs are fused appropriately.

Inputs
1. Low Water Level
2. Medium Water Level
3. High Water Level
4. Door
5. Coin 1 Signal
6. Coin 2 Signal
7. *Prep for Card Reader or Central Pay (“start
pulse”)
* This allows machine to interface with the card reader or the
central pay system. “Start Pulse” originates from the reader/
central pay system, and this satisfies the programmed vend.
B control provides “Machine Available” signal to reader/
central pay when it is ready to accept payment. Refer to
Machine Electrical Schematic.

Control Voltage

Summary of Control Outputs and
Inputs

The control power supply can be configured to operate
on 110 Volt AC nominal RMS input voltage
50/60 Hertz, OR 220 Volt AC nominal RMS input
voltage 50/60 Hertz.

Outputs

Harnessing

General outputs provide signals to operate the
following components.

Wiring harnesses are modular – harnesses common to
various configurations are similar, while those specific
to a certain configuration can be added. There are
harnesses for inputs to the control unit, for outputs
from the control power/output unit to the machine
components, and for the main incoming power to the
control power/output unit.

1. Hot Fill Valve (HF)
2. Cold Fill Valve (CF)
3. Drain Valve (normally open) (DR)
4. Door Lock Solenoid Coil (DL)
5. Door Unlock Solenoid Coil (DU)
6. Supply 1 (detergent) (S1)

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

9

Introduction

Communications

Third Party Card Reader

Central Pay System

(Card Reader Models Only)

(Central Pay System Models Only)
The models are usually designated by the “Prep for
Central Pay” option. The model number will have an
“L” in the 6th digit (i.e. *C40BL2OU6001). Refer to
Nameplate Location. The control will accept a start
pulse from the central pay system and will give a
“machine available” signal.
* Denotes Brand

For detailed information on the Central Pay System
Communications, refer to the manufacturer.

10

The models are usually designated by the “Prep for
Card Reader” option. The model number will have a
“Y” in the 6th digit (i.e. *C40BY2OU6001). Refer to
Nameplate Location. The control will accept
communications with a Card Reader in order to
perform vending transactions when a card is inserted
to pay for cycles.
* Denotes Brand

For detailed information on the Card Reader
Communications, refer to the manufacturer.

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Introduction

Model Number Familiarization Guide
Sample Model Number: *C40BY2OU60001
*C

Model Number Prefix

40

Washer-Extractor Capacity (pounds dry weight of laundry)

B

Type of Electrical Control

Y

Actuation (Y = Prep for Card Reader)

2

Washer-Extractor Speed Capability (2 = 2 speed)

O

Electrical Characteristics

U6

Design Series

0001

Option Identification (varies from machine to machine)

* Denotes Brand

*C40BY2OU60001
00000000000
208 – 240

7
3

60

3
60
N/A

3
18

470
N/A

0

500000
EXAMPLE OF NAMEPLATE

CHM523R
CHM523R

Figure 2

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

11

Programming
NOTE: The machines are factory programmed
with basic cycles to make the units operational
without programming at installation.

Entering Program Mode
1. Open machine lid.
2. Locate Program/Run switch on the computer
board. This is accessed through a cutout in the
metal control unit cover. This switch protrudes
from the rear of the electronic control unit cover.
3. Flip switch to the left (as seen from front of
machine) to enter PROGRAM Mode.
4. Display will show “0000” or temperature or
“tSFL” (depending on version of the control).

Determining Firmware ID Code
1. Turn on the main power source (circuit breaker or
cut-off switch on wall).
2. Display will show Firmware ID code (i.e.,
“C2dS” and “CvdS” etc…).
3. Record Firmware ID Code for future reference.

12

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Programming

Programming Vend Price
(For Models with Firmware ID Code
“C2dS” and “CvdS”)
Setup Mode
NOTE: In SETUP Mode, certain machine
functions can be configured. The settings in this
mode are related to how the machine is equipped
from the factory. Usually, these would not be
changed in the field.
NOTE: Enter SETUP Mode through the
PROGRAM Mode. Refer to Entering Program
Mode.
1. Press (*) keypad. Display shows machine model
size (capacity). Displayed capacity must match
machine size. Press (∧) keypad to change the
capacity. (This should already be set correctly
from the factory, and normally should never need
to be changed).
2. Press START (Enter) keypad.
3. Display shows “FAr” or “CEL”.
NOTE: This option selects whether temperatures
display in degrees Fahrenheit (F) or Celsius (C), if
control is equipped with a temperature sensor.
Press the (∧) or (∨) keypad to change degrees
“FAr” or “CEL”.
4. Press START (Enter) keypad.
5. If model displays “HEAt” or “noHt”, change the
selection by pressing the (∧) or (∨) keypad. If
model displays “CArd” or “COIn”, skip to
step# 8.
6. Press START (Enter) keypad to continue to the
next step.
7. “EFIL” or “nEFL” will display in certain models.
“EFIL” means the capability to control an extra
fill valve with programmable water level (same
as regular fills) is enabled. Machine MUST be
equipped with the extra valve for this to work
properly. “nEFL” means the extra fill valve
option is disabled or not installed on machine.
NOTE: If neither message displays, the extra fill
capability is not present. If either message displays,
changing the selection is an option by pressing the
(∧) or (∨) keypad. Press START (Enter) keypad to
continue to the next option.

8. If model displays the message “CArd” or
“COIn”, change the selection by pressing the (∧)
or (∨) keypad.
9. Press START (Enter) keypad to continue to the
next selection.
NOTE: Select “COIn used by accessory pay
system. Contact the manufacturer of the accessory
pay system if not working properly
10. “bEEP” or “nobP” will display in certain models.
If “bEEP” is set, control will beep during Add
Bleach (Supply 2) and at end of cycle after
several seconds while displaying “dOnE”. If
“nobP” displays, control will NOT beep during
Add Bleach (Supply 2) or at end of cycle. This
does not affect the short beep when a keypad is
pressed or a coin is inserted and it does not affect
the beep during an alarm. Press the (∧) or (∨)
keypad to change “bEEP”/“nobP” selection.
11. Press START (Enter) keypad to continue to next
step.
12. “PtIn” means the control will display remaining
time in a cycle without fill and drain times.
“EtIn” means the control will display estimated
remaining time in a cycle including fill and drain
time.
13. Press the (∧) or (∨) keypad to change “PtIn”/
“EtIn” selection.
14. Press START (Enter) keypad to continue to the
next step.
NOTE: If machine is equipped with a card reader,
or interfaces with a control/remote pay system,
setting “con1”/ “dEno” and “con2”/ “dEno” equal
to the vend start amount (“Strt”/ “Ant”) will allow
starting with one pulse and is recommended. The
card or central remote pay vend amount should
match the “Strt”/ “Ant” setting.
15. Display shows “con1”, “dEno” next, then a
number such as 25. This means that the coin 1
denomination is 25 cents for single coin meters.
For example, a U.S. quarter coin meter would be
set for 25 cents, or this would be the amount for
one of the two denominations for a dual coin
meter, such as a U.S. quarter for a dollar/quarter
dual coin meter. The vend price programmed
above will count down by this amount each time
a coin is added.
16. Press the (∧) or (∨) keypad to decrease or
increase this amount.
17. When correct, press START (Enter) keypad.

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

13

Programming

18. Display shows “con2”, “dEno” next, then a
number such as 100. This means that the coin 2
denomination is 100 cents. This is the coin
denomination for coin meters that can process
two types of coins – such as a U.S. quarter/dollar
coin meter. The second coin input would be one
dollar. For single coin meters, press START
(Enter) keypad to continue. The vend price
programmed above will count down by this
amount each time this second coin type is added.
19. Press the (∧) or (∨) keypad to decrease or
increase this amount.
20. When correct, press START (Enter) keypad.
21. Display shows “Strt”, “Ant” next, then a number
such as 150. This means that the start amount is
150 cents. This is the vend price required to
operate a wash cycle.
22. Press the (∨) or (∧) keypad to increase or
decrease this amount.
23. When correct, press START (Enter) keypad.
24. Display shows “0000” when complete. Return
the Program/Run switch to the right and close the
lid. The display will show new vend price.

Cycle and Error Count
The control logs cycle count (total of all cycles
completed).

Cycle and Error Count addition

7. Press START (Enter) keypad. Displays show a
number (up to 4 digits) showing how many
complete cycles have been operated. This
excludes cycles stopped because of an error.
8. Press START (Enter) keypad.
9. If display does not show “E Pr”, control will
revert to normal PROGRAM Mode.
10. If display shows “E Pr”, this is for factory
reference regarding power interruption. Press
START (Enter) keypad. A number will display.
Press START (Enter) keypad. After a brief pause,
the control will display normal PROGRAM
Mode.

Programming Cycle Segments
The machine is preprogrammed with eight wash cycle
formulas that can be edited.
To edit any of these cycles, enter PROGRAM Mode.
Refer to Entering Program Mode. In PROGRAM
Mode, cycles are selected by number (1 through 8) as
opposed to the RUN Mode, where cycles are selected
by pressing one of the eight corresponding keypads.
The keypads must serve different functions in each
mode because there are more functions than keypads
in PROGRAM Mode.
In RUN Mode the top left keypad selects Cycle 1, the
(∧) keypad directly below it selects Cycle 2, etc.
Figure 3 shows which keypad selects each cycle in
RUN Mode.

1. To read, enter PROGRAM Mode. Refer to
Entering Program Mode.

1. After entering PROGRAM Mode, display will
show “0000” or temperature (if machine is
configured for heat) or “tSFL”.

2. Press START (Enter) keypad. Display shows
“Erdn” (indicates Drain Error count).

2. Press the (∧) keypad to enter Cycle
Programming Mode.

3. Press START (Enter) keypad. Display shows a
number (2 or 3 digits) showing how many drain
errors have occurred. This number can range
from ‘00’ to ‘255’, and cannot be set to zero.

3. The display will reference cycles by number.
Cycle 1 will show first.

4. Press START (Enter) keypad. Display shows
“ErFL” (indicates Fill Error count).
5. Press START (Enter) keypad. Display shows a
number (2 or 3 digits showing how many fill
errors have occurred. This number can range
from ‘00’ to 255’, and cannot be set to zero.

4. Use the (∧) or (∨) keypad to select cycle to be
edited.
5. Press START (Enter) keypad to move into the
menu of options.

6. Press START (Enter) keypad. Display shows
“CYC ” (indicates Cycle count).

14

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Programming

Programming Vend Price
(For Earlier Models)
Setup Mode
NOTE: In SETUP Mode, certain machine
functions can be configured. The settings in this
mode are related to how the machine is equipped
from the factory. Usually, these would not be
changed in the field.
NOTE: Enter SETUP Mode through the
PROGRAM Mode. Refer to Entering Program
Mode.
1. Press (*) keypad. Display shows machine model
size (capacity). Displayed capacity must match
machine size.
2. Press (∧) keypad to change the capacity. (This
should already be set correctly from the factory,
and normally should never need to be changed).
3. Press START (Enter) keypad.
4. Display shows “FAr” or “CEL”.
NOTE: This option selects whether temperatures
display in degrees Fahrenheit (F) or Celsius (C), if
control is equipped with a temperature sensor.
Press the (∧) or (∨) keypad to change degrees
“FAr” or “CEL”.
5. Press START (Enter) keypad.

NOTE: If neither message displays, the extra fill
capability is not present. If either message displays,
changing the selection is an option by pressing the
(∧) or (∨) keypad. Press START (Enter) keypad
to continue to the next option.
10. If model displays the message “CArd” or
“COIn”, change the selection by pressing the (∧)
or (∨) keypad.
11. When correct, press START (Enter) keypad to
continue to the next selection.
NOTE: Select “COIn” for regular coin drop meter
or if coin inputs are used by accessory pay system.
Contact the manufacturer of the accessory pay
system if not working properly.
12. “bEEP” or “nobP” will display in certain models.
If “bEEP” is set, control will beep during Add
Bleach (Supply 2) and at end of cycle after
several seconds while displaying “dOnE”. If
“nobP” displays, control will NOT beep during
Add Bleach (Supply 2) or at end of cycle. This
does not affect the short beep when a keypad is
pressed or a coin is inserted and it does not affect
the beep during an alarm.
13. Press the (∧) or (∨) keypad to change “bEEP”/
“nobP” selection.
14. Press START (Enter) keypad to continue to next
step.

6. If model displays “HEAt” or “noHt”, change the
selection by pressing the (∧) or (∨) keypad.
7. If model displays “CArd” or “COIn”, skip to
step #10.
8. Press START (Enter) keypad to continue to the
next step.
9. “EFIL” or “nEFL” will display in certain models.
“EFIL” means the capability to control an extra
fill valve with programmable water level (same
as regular fills) is enabled. Machine MUST be
equipped with the extra valve for this to work
properly. “nEFL” means the extra fill valve
option is disabled or not installed on machine.

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

15

Programming

NOTE: If machine is equipped with a card reader,
or interfaces with a control/remote pay system,
setting “con1”/ “dEno” and “con2”/ “dEno” equal
to the vend start amount (“Strt”/ “Ant”) will allow
starting with one pulse and is recommended. The
card or central remote pay vend amount should
match the “Strt”/ “Ant” setting.
15. Display shows “con1”, “dEno” next, then a
number such as 25. This means that the coin 1
denomination is 25 cents for single coin meters.
For example, a U.S. quarter coin meter would be
set for 25 cents or this would be the amount for
one of the two denominations for a dual coin
meter, such as a U.S. quarter for a dollar/quarter
dual coin meter. The vend price programmed
above will count down by this amount each time
a coin is added.
16. Press the (∧) or (∨) keypad to decrease or
increase this amount.
17. When correct, press START (Enter) keypad.
18. Display shows “con2”, “dEno” next, then a
number such as 100. This means that the coin 2
denomination is 100 cents. This is the coin
denomination for coin meters that can process
two types of coins – such as a U.S. quarter/dollar
coin meter. The second coin input would be one
dollar. For single coin meters, press START
(Enter) keypad to continue. The vend price
programmed above will count down by this
amount each time this second coin type is added.
19. Press the (∧) or (∨) keypad to decrease or
increase this amount.
20. When correct, press START (Enter) keypad.
21. Display shows “Strt”, “Ant” next, then a number
such as 150. This means that the start amount is
150 cents. This is the vend price required to
operate a wash cycle.
22. Press the (∨) or (∧) keypad to decrease or
increase this amount.
23. When correct, press START (Enter) keypad.
24. Display shows “0000” when complete. Return
the Program/Run switch to the right and close the
lid. The display will show new vend price.

16

Cycle and Error Count
The control logs cycle count (total of all cycles
completed).
1. To read, enter PROGRAM Mode. Refer to
Entering Program Mode.
2. Press START (Enter) keypad. Display will show
the cycle count.
3. Press START (Enter) keypad. Display will show
certain error conditions that may have been
recorded by the control.
4. Read the information when consulting technical
assistance as needed.
5. Step through the error log by pressing START
(Enter) keypad repeatedly until display reverts to
normal PROGRAM Mode (“0000” or
temperature).

Programming Cycle Segments
The machine is preprogrammed with eight wash cycle
formulas that can be edited.
To edit any of these cycles, enter PROGRAM Mode.
Refer to Entering Program Mode. In PROGRAM
Mode, cycles are selected by number (1 through 8) as
opposed to the RUN Mode, where cycles are selected
by pressing one of the eight corresponding keypads.
The keypads must serve different functions in each
mode because there are more functions than keypads
in PROGRAM Mode.
In RUN Mode the top left keypad selects Cycle 1, the
(∧) keypad directly below it selects Cycle 2, etc.
Figure 3 shows which keypad selects each cycle in
RUN Mode.
1. After entering PROGRAM Mode, display will
show “0000” or temperature (if machine is
configured for heat).
2. Press the (∧) keypad to enter Cycle Programming
Mode. The display will reference cycles by
number. Cycle 1 will show first.
3. Use the (∧) or (∨) keypad to select cycle to be
edited.
4. Press START (Enter) keypad to move into the
menu of options.

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Programming

2

1

15
NORMAL

14

WASH
ADD
BLEACH

13

RINSE

12

SPIN

HOT

WARM

NORMAL

PERM PRESS

WARM

COLD

QUICK WASH

QUICK WASH

HOT
HEAVY SOIL

1
5

15

PERM PRESS

6
7

START

DOOR

11

2

5

8

WARM
DELICATE

14
13
12

95C

95C

60C

60C

40C

40C

6
7
8

11
30C

9

3

4

10

COLD

CHM482R

9

DOMESTIC MODELS

3

4

CHM488R

INTERNATIONAL MODELS
CHM482R

1
2
3
4
5
6
7
8

<

HOT

<

10

Cycle 1
Cycle 2
Cycle 3
Cycle 4/ “∧” Edit
Cycle 5
Cycle 6
Cycle 7
Cycle 8/ “∨” Edit

CHM488R

9
10
11
12
13
14

START (Enter) Keypad
“Clean Filter” Indicator LED (Active only for
C60FX, C80 and C125 Models)
Door Open LED
Spin Cycle LED
Rinse Cycle LED
Add Bleach LED

Figure 3

NOTE: If the version of control in machine is
capable of reading temperature, pressing the
START (Enter) keypad while a wash is running
will cause the display to show temperature.
Depending on version of control, this will either
revert to minutes remaining after several seconds,
or START (Enter) keypad must be pressed a
second time to revert to minutes remaining.

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

17

Programming

Options for Each Segment
Cycle Steps Available

(NOTE: WASH, ADD BLEACH, RINSE
and SPIN LEDs light ONLY when a
cycle formula is in operation.)

Display

Setting Options for Cycle Steps

Wash 1 (displayed as “USH1”)
Time for Agitation (excludes fill, drain,
spin and heat)

GEnt
norn

Fill valves (temperature)

CFIL
HFIL

0 or 2-30 minutes in agitation step (increases/decreases in
one-minute increments). Refer to Table 3 for operation of
each agitation segment
Cold, Hot or Both (warm) water fills or Extra fill (must be
configured for “EFIL” in SETUP Mode)

bFIL
EFIL
Fill water level control

LO

Low, Medium or High water level

nEd
HI
Supply

SUP0
SUP1

SUP0 for No Supply or Supply 1-3,6 (Refer to Table 2 for
operation of each supply selection)

SUP2
SUP3
SUP6
Heat (Models with heat or heat capability) HEAt
noHt
Drain (Final segment drains in stop
routine if No Drain is programmed)

drAI

Spin time

SPIn

nodr
tInE

00F (no heat for segment) or 80°F to 205°F
00C (no heat for segment) or 27°C to 95°C
Drain or No Drain (if No Drain programmed, will skip spin
segment associated with Drain segment)
00 for No Spin or 30-240 seconds (increases/decreases in
one-second increments)

Wash 2 (displayed as “USH2”)
Time for Agitation (excludes fill, drain,
spin and heat)

GEnt
norn

Fill valves (temperature)

CFIL
HFIL

0 or 2-20 minutes in agitation step (increases/decreases in
one-minute increments). Refer to Table 3 for operation of
each agitation segment
Cold, Hot or Both (warm) water fills or Extra fill (must be
configured for “EFIL” in SETUP Mode)

bFIL
EFIL
Fill water level control

LO

Low, Medium or High water level

nEd
HI
Supply

SUP0
SUP1

SUP0 for No Supply or Supply 1-3,6 (Refer to Table 2 for
operation of each supply selection)

SUP2
SUP3
SUP6
Table 1 (continued)

18

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Programming
Table 1 (continued)
Cycle Steps Available

(NOTE: WASH, ADD BLEACH, RINSE
and SPIN LEDs light ONLY when a
cycle formula is in operation.)

Display

Heat (Models with heat or heat capability) HEAt
noHt

Setting Options for Cycle Steps
00F (no heat for segment) or 80°F to 205°F
00C (no heat for segment) or 27°C to 95°C

Drain (Final segment drains in stop
routine if No Drain is programmed)

drAI

Spin time

SPIn

00 for No Spin or 30-240 seconds (increases/decreases in
one-second increments)

Time for Agitation (excludes fill, drain,
spin and heat)

GEnt

0 or 2-15 minutes in agitation step (increases/decreases in
one-minute increments). Refer to Table 3 for operation of
each agitation segment

Fill valves (temperature)

CFIL

nodr

Drain or No Drain (if No Drain programmed, will skip spin
segment associated with Drain segment)

Wash 3 (displayed as “USH3”)
norn

HFIL

Cold, Hot or Both (warm) water fills or Extra fill (must be
configured for “EFIL” in SETUP Mode)

bFIL
EFIL
Fill water level control

LO

Low, Medium or High water level

nEd
HI
Supply

SUP0
SUP1

SUP0 for No Supply or Supply 1-3,6 (Refer to Table 2 for
operation of each supply selection)

SUP2
SUP3
SUP6
Heat (Models with heat or heat capability) HEAt
noHt

00F (no heat for segment) or 80°F to 205°F
00C (no heat for segment) or 27°C to 95°C

Drain (Final segment drains in stop
routine if No Drain is programmed)

drAI

Spin time

SPIn

00 or 30-240 seconds (increases/decreases in one-second
increments)

GEnt

0 or 2-15 minutes in agitation step (increases/decreases in
one-minute increments). Refer to Table 3 for operation of
each agitation segment

nodr

Drain or No Drain (if No Drain programmed, will skip spin
segment associated with Drain Segment)

Wash 4 (displayed as “USH4”)
Time for Agitation (excludes fill, drain,
spin and heat)

norn

Fill valves (temperature)

CFIL
HFIL

Cold, Hot or Both (warm) water fills or Extra fill (must be
configured for “EFIL” in SETUP Mode)

bFIL
EFIL
Fill water level control

LO

Low, Medium or High water level

nEd
HI
Table 1 (continued)

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

19

Programming
Table 1 (continued)
Cycle Steps Available

(NOTE: WASH, ADD BLEACH, RINSE
and SPIN LEDs light ONLY when a
cycle formula is in operation.)

Supply

Display
SUP0
SUP1

Setting Options for Cycle Steps
SUP0 for No Supply or Supply 1-3,6 (Refer to Table 2 for
operation of each supply selection)

SUP2
SUP3
SUP6
Heat (Models with heat or heat capability) HEAt
noHt
Drain (Final segment drains in stop
routine if No Drain is programmed)
Spin time

drAI
nodr
SPIn
tInE

00F (no heat for segment) or 80°F to 205°F
00C (no heat for segment) or 27°C to 95°C
Drain or No Drain (if No Drain programmed, will skip spin
segment associated with Drain segment)
00 for No Spin or 30-240 seconds (increases/decreases in
one-second increments)

Rinse 1 (displayed as “rIn1”)
Time for Agitation (excludes fill, drain,
spin and heat)

GEnt

Fill valves (temperature)

CFIL

norn

HFIL

0 or 2-15 minutes in agitation step (increases/decreases in
one-minute increments). Refer to Table 3 for operation of
each agitation segment
Cold, Hot or Both (warm) water fills or Extra fill (must be
configured for “EFIL” in SETUP Mode)

bFIL
EFIL
Fill water level control

LO

Low, Medium or High water level

nEd
HI
Supply

SUP0
SUP1

SUP0 for No Supply or Supply 1-3,6 (Refer to Table 2 for
operation of each supply selection)

SUP2
SUP3
SUP6
Heat (Models with heat or heat capability) HEAt
noHt
Drain (Final segment drains in stop
routine if No Drain is programmed)

drAI

Spin time

SPIn

nodr

00F (no heat for segment) or 80°F to 205°F
00C (no heat for segment) or 27°C to 95°C
Drain or No Drain (if No Drain programmed, will skip spin
segment associated with Drain segment)
00 for No Spin or 30-240 seconds (increases/decreases in
one-second increments)
Table 1 (continued)

20

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Programming
Table 1 (continued)
Cycle Steps Available

(NOTE: WASH, ADD BLEACH, RINSE
and SPIN LEDs light ONLY when a
cycle formula is in operation.)

Display

Setting Options for Cycle Steps

Rinse 2 (displayed as “rIn2”)
Time for Agitation (excludes fill, drain,
spin and heat)

GEnt
norn

Fill valves (temperature)

CFIL
HFIL

0 or 2-15 minutes in agitation step (increases/decreases in
one-minute increments). Refer to Table 3 for operation of
each agitation segment
Cold, Hot or Both (warm) water fills or Extra fill (must be
configured for “EFIL” in SETUP Mode)

bFIL
EFIL
Fill water level control

LO

Low, Medium or High water level

nEd
HI
Supply

SUP0
SUP1

SUP0 for No Supply or Supply 1-3,6 (Refer to Table 2 for
operation of each supply selection)

SUP2
SUP3
SUP6
Heat (Models with heat or heat capability) HEAt
noHt

00F (no heat for segment) or 80°F to 205°F
00C (no heat for segment) or 27°C to 95°C

Drain (Final segment drains in stop
routine if No Drain is programmed)

drAI

Spin time

SPIn

00 or 30-240 seconds (increases/decreases in one-second
increments)

GEnt

0 or 2-15 minutes in agitation step (increases/decreases in
one-minute increments). Refer to Table 3 for operation of
each agitation segment

nodr

Drain or No Drain (if No Drain programmed, will skip spin
segment associated with Drain segment)

Rinse 3 (displayed as “rIn3”)
Time for Agitation (excludes fill, drain,
spin and heat)
Fill valves (temperature)

norn
CFIL
HFIL

Cold, Hot or Both (warm) water fills or Extra fill (must be
configured for “EFIL” in SETUP Mode)

bFIL
EFIL
Fill water level control

LO

Low, Medium or High water level

nEd
HI
Supply

SUP0
SUP1

SUP0 for No Supply or Supply 1-3,6 (Refer to Table 2 for
operation of each supply selection)

SUP2
SUP3
SUP6
Table 1 (continued)

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

21

Programming
Table 1 (continued)
Cycle Steps Available

(NOTE: WASH, ADD BLEACH, RINSE
and SPIN LEDs light ONLY when a
cycle formula is in operation.)

Display

Heat (Models with heat or heat capability) HEAt
noHt
Drain (Final segment drains in stop
routine if No Drain is programmed)

drAI

Spin time

SPIn

nodr
tInE

Setting Options for Cycle Steps
00F (no heat for segment) or 80°F to 205°F
00C (no heat for segment) or 27°C to 95°C
Drain or No Drain (if No Drain programmed, will skip spin
segment associated with Drain segment)
00 for No Spin or 30-240 seconds (increases/decreases in
one-second increments)

Rinse 4 (displayed as “rIn4”)
Time for Agitation (excludes fill, drain,
spin and heat)

GEnt

Fill valves (temperature)

CFIL

norn

HFIL

0 or 2-15 minutes in agitation step (increases/decreases in
one-minute increments). Refer to Table 3 for operation of
each agitation segment
Cold, Hot or Both (warm) water fills or Extra fill (must be
configured for “EFIL” in SETUP Mode)

bFIL
EFIL
Fill water level control

LO

Low, Medium or High water level

nEd
HI
Supply

SUP0
SUP1

SUP0 for No Supply or Supply 1-3,6 (Refer to Table 2 for
operation of each supply selection)

SUP2
SUP3
SUP6
Heat (Models with heat or heat capability) HEAt
noHt
Drain (Final segment drains in stop
routine if No Drain is programmed)

drAI

Spin time

SPIn

nodr

00F (no heat for segment) or 80°F to 205°F
00C (no heat for segment) or 27°C to 95°C
Drain or No Drain (if No Drain programmed, will skip spin
segment associated with Drain segment)
00 for No Spin or 1-10 minutes (increases/decreases in oneminute increments)
Table 1

22

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Programming

NOTE: If the wash load becomes out of balance,
the machine will attempt to balance the load. After
three failed attempts the display will light the
leftmost digit and a lower spin will be used to
complete the cycle. Refer to Figure 4.

1
NORMAL

WASH
ADD
BLEACH
RINSE
SPIN

PERM PRESS

HOT

WARM

NORMAL

PERM PRESS

WARM

COLD

QUICK WASH

QUICK WASH

START

DOOR

WARM

HOT
HEAVY SOIL

DELICATE

HOT

COLD

CHM524R

1

Out-of-Balance LED

Figure 4
Supply Programmed

External Chemical Supply Signal

Compartment Flushed

SUP0

None

None

SUP1

Supply 1

Compartment 1

SUP2

Supply 2*

Compartment 2

SUP3

Supply 3

Compartment 3

SUP6

Supply 6**

Compartment 1 and 2
Table 2

*NOTE: ADD BLEACH LED lights if Supply 2 is
the only supply programmed. If set up for
"bEEP"(refer to SETUP Mode section), buzzer will
sound on and off for the first eight seconds. The
Supply 2 and ADD BLEACH LED remain on for
45 seconds or until the fill is complete, whichever
comes first.
**NOTE: Selecting "EFIL" (Extra fill) in SETUP
Mode will remove supply 6 as optional supply
signals.

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

23

Programming

To Edit an Entire Wash Cycle
Formula

10. Press the (∧) or (∨) keypad to alter the selection,
or the START (Enter) keypad to continue.

1. Enter PROGRAM Mode. Refer to Entering
Program Mode.

11. Display shows “CFIL”, “HFIL”, “bFIL” or
“EFIL” for Cold, Hot, Both (warm) or Extra fill,
respectively.

2. Press the (∧) keypad until display shows
“CY01”.

12. Press the (∧) or (∨) keypad to alter the selection,
or the START (Enter) keypad to continue.

3. Press the (∧) or (∨) keypad until cycle to be
edited is displayed.
4. Press START (Enter) keypad to select the cycle
desired. Refer to Figure 3, showing which cycle
number corresponds to each keypad when in
RUN Mode.
Agitation for the cycle
5. With display showing “CY_x” (x = cycle
number), press the START (Enter) keypad.
6. Display shows either “norn” (for normal
agitation), or “GEnt” (for gentle agitation). Refer
to Table 3.

NOTE: Extra fill (“EFIL”) is possible only if
configured for “EFIL” in SETUP Mode. If model is
not configured for the extra fill valve, “nEFL” will
display. If configured, a third valve can be
controlled.
13. Display shows “LO”, “nEd”, or “HI” for Low,
Medium, or High water level, respectively.
14. Press the (∧) or (∨) keypad to alter the
selection, or the START (Enter) keypad to
continue.

7. Press the (∧) or (∨) keypad to alter the selection,
or the START (Enter) keypad to continue.

15. Display shows “SUP0”, “SUP1”, “SUP2”,
“SUP3”, or “SUP6” (or “S 12” depending on
version of control). Refer to Table 2 for operation
of each supply selection.

Display

16. Press the (∧) or (∨) keypad to alter the selection,
or the START (Enter) keypad to continue.

Meaning

norn

12 seconds forward, 3 seconds pause,
12 seconds reverse, 3 seconds pause, and
repeat for programmed time.

GEnt

3 seconds forward, 12 seconds pause,
3 seconds reverse, 12 seconds pause and
repeat for programmed time
Table 3

Wash 1 – Wash 4
NOTE: Programming a time other than “00” for
Wash 1 will make the WASH indicator LED light
while this step is running, but NOT in PROGRAM
Mode.
8. The main display shows “USH1” indicating you
are in the Wash segment (number will reflect
selected Wash cycle 1-4).
9. Press START (Enter) keypad. Display shows
agitation time during the step: “00” (skips
segment) or 2-30 minutes. Wash 2 agitation’s
time can be 2-20 minutes, 2-15 minutes for Wash
3 and Wash 4 or “00” to skip Wash 2, Wash 3 or
Wash 4. This is the time after the fill and before
the drain and does not include spin time or time
to first reach a programmed temperature (if
machine is configured for heat).

24

NOTE: If programmed for “SUP2”, the ADD
BLEACH indicator LED light turns on and is set
up for “bEEP” the buzzer sounds for the first eight
seconds Supply 2 is on.
Heated Models Only
17. Display shows temperature in degrees F or C.
Display will show degrees F if configured for
“FAr” in SETUP Mode, or degrees C if
configured for “CEL” in SETUP Mode. Range is
80°F to 205°F, or 00F (no heat for segment), or
27°C to 95°C, or 00C (no heat for segment).

WARNING
To prevent personal injury, avoid contact
with inlet water temperatures higher than
125° Fahrenheit (51° Celsius) and hot
surfaces.
W748

18. Press the (∧) keypad to increase, or (∨) keypad
to decrease temperature in one-degree
increments.
The control will energize heat and pause cycle timing
for up to 40 minutes until the programmed
temperature is first reached.

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Programming

NOTE: If temperature is not reached after
40 minutes, control resumes cycle.

27. Display shows “CFIL”, “HFIL”, “bFIL” or
“EFIL” for Cold, Hot, Both (warm) or Extra fill.

After cycle resumes, control will attempt to maintain
programmed temperature if it senses water in the
machine.

28. Press the (∧) or (∨) keypad to alter the selection,
or the START (Enter) keypad to continue.

NOTE: Temperature display applies ONLY if
machine is configured for “HEAt” in SETUP
Mode. Machine must be equipped with electric or
steam heat and a temperature sensor. If configured
for “noHt” (no heat capability) in SETUP Mode,
temperature display does not appear in the
segment. After temperature setting, control will
skip to “drAI”/“nodr” or Spin Time, depending on
version.
19. If display shows “drAI”/“nodr” during segment
programming, a drain step option will appear at
the end of the segment.
20. Select “drAI” for a drain step followed by an
optional spin. Select “nodr” for no drain step.
NOTE: The machine will proceed directly to the
next segment if “nodr”.
21. Change the selection by pressing the (∧) or (∨)
keypad, or the START (Enter) keypad to
continue.
22. If “drAI” is selected (or if your model does not
provide the option of selecting “drAI”/“nodr”),
the display will show “SPIn” one second, “tInE”
one second, and then the time for spin: “00” (no
spin) or 30-240 seconds.
23. Change the selection by pressing the (∧) or (∨)
keypad or the START (Enter) keypad to continue.

Rinse 1 – Rinse 4
NOTE: Programming a time other than “00” for
this step will make the RINSE indicator LED light
while this step is running, but not in PROGRAM
Mode.
24. The main display shows “rIN1” indicating you
are in the Rinse segment (number will represent
Rinse cycle selected 1-4).
25. Press START (Enter) keypad. Display shows the
time for agitation during the step: “00” (skips
segment) or 2-15 minutes. This is the time after
the fill and before the drain and does not include
spin time.
26. Press the (∧) or (∨) keypad to alter the selection,
or the START (Enter) keypad to continue.

F232157

NOTE: Extra fill (“EFIL”) is possible only if
configured for “EFIL” in SETUP Mode. If
configured, a third valve can be controlled.
29. Display shows “LO”, “nEd”, or “HI” for Low,
Medium, or High water level, respectively.
30. Press the (∧) or (∨) keypad to alter the selection,
or the START (enter) keypad to continue.
31. Display shows “SUP0”, “SUP1”, “SUP2”,
“SUP3”, or “SUP6” (or “S 12” depending on
version of control). Refer to Table 2 for operation
of each supply selection.
32. Press the (∧) or (∨) keypad to alter the selection,
or the START (Enter) keypad to continue.
NOTE: If programmed for “SUP2”, the ADD
BLEACH indicator LED light turns on and is set
up for “bEEP” the buzzer sounds for the first eight
seconds Supply 2 is on.
Heated Models Only
33. Display shows temperature in degrees F or C.
Display will show degrees F if configured for
“FAr” in SETUP Mode, or degrees C if
configured for “CEL” in SETUP Mode. Range is
80°F to 205°F, or 00F (no heat for segment), or
27°C to 95°C, or 00C (no heat for segment).

WARNING
To prevent personal injury, avoid contact
with inlet water temperatures higher than
125° Fahrenheit (51° Celsius) and hot
surfaces.
W748

34. Press the (∧) keypad to increase, or (∨) keypad
to decrease temperature. Temperature changes in
one-degree increments.
The control will energize heat and pause cycle timing
for up to 40 minutes until the programmed temperature
is first reached.
NOTE: If temperature not reached after
40 minutes, control resumes cycle.
After cycle resumes, control will attempt to maintain
programmed temperature if it senses water in the
machine.

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

25

Programming

NOTE: Temperature display applies ONLY if
machine is configured for “HEAt” in SETUP
Mode. Machine must be equipped with electric or
steam heat and a temperature sensor. If configured
for “noHt” (no heat capability) in SETUP Mode,
temperature display does not appear in the
segment. After temperature setting, control will
skip to “drAI”/“nodr” or Spin Time, depending on
version. If “HEAt”/ “noHt” does not appear in
SETUP Mode, no heating is possible.
35. If display shows “drAI”/“nodr” during segment
programming, a drain step option will appear at
the end of the segment.
36. Select “drAI” for a drain step followed by an
optional spin. Select “nodr” for no drain step.
NOTE: The machine will proceed directly to the
next segment if “nodr”.
37. Change the selection by pressing the (∧) or (∨)
keypad or the START (Enter) keypad to continue.
38. If “drAI” is selected (or if your model does not
provide the option of selecting “drAI”/“nodr”),
the display will show “SPIn” one second, “tInE”
one second, and then the time for spin: “00” (no
spin) for 30-240 seconds IF you are in Rinse 1, 2,
or 3. If you are in Rinse 4, the time for spin will
show 0 or 1-10 minutes.
39. Change the selection by pressing the (∧) or (∨)
keypad, or the START (Enter) keypad to
continue.
IMPORTANT: The spin time in Rinse 4 is
programmed in minutes (0-10 minutes, in
one-minute increments), while other spins are in
seconds to allow for shorter times (such as
45 seconds). (Rinse 4 segment should usually be
used as the final rinse, even where there may be
fewer than four rinses. Program zero time for
preceding rinses you wish to exclude.)
40. Display shows “0000” if control cannot read
temperature or a temperature if control is capable
of a temperature reading.
41. Exit PROGRAM Mode by moving the Program/
Run switch back to the right as seen from the
front of the machine.
NOTE: The SPIN indicator LED will automatically
light during the wash cycle when the last spin
programmed in a cycle is operating (regardless of
which segment).

26

Abnormal Conditions
Door Will Not Lock
If the door handle has not been properly positioned to
allow locking the door, the control will sense this and
retract the door lock solenoid. The display will show
“----” for about 5 seconds, then will flash “SHUt”/
“dOOr” for about 5 seconds while sounding the
buzzer, prompting the user to close the door properly.
The DOOR indicator LED then lights. The machine
user should properly shut the door, then press START
(Enter) again. If the door is still not locking correctly,
the process above will repeat up to five times. After
this, the display flashes “CAnt”/“LOC” (cannot lock
door). The user can cause this to start over (five more
attempts) by pressing START (Enter) keypad twice. If
this continues, it indicates a problem, and a qualified
service technician should be consulted.

Door Open During Operation
If the control senses either a momentary or sustained
open door while the machine is operating in a wash
cycle, the control immediately attempts to halt rotation
of the cylinder. All outputs not required to effect rapid
halting of the cylinder rotation de-energize
immediately. The message “dOOr” then displays as
long as the condition persists. Regardless of the
duration of the open door condition, once it is
recognized by the control, the control aborts the cycle
and goes to the stop routine even if the door is closed.

Excessive Fill Time
Fill times exceeding 10 minutes cause the cycle to
abort. Display flashes “StOP”/“FILL” and sounds the
buzzer for 10 seconds prior to entering the stop routine
(display shows “01” minutes remaining while in the
stop routine). The Fill Error Count will increase by
one. Refer to Cycle and Error Count section.

Out-of-Balance
If the machine goes out of balance, the machine will
attempt to balance the load. After three attempts, the
display will light the leftmost digit and a lower spin
will be used.

WARNING
Operating the machine with severe out-ofbalance loads could result in personal
injury and serious equipment damage.

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

W728

F232157

Programming

Drain Error (For Models With Firmware ID
Code “C2dS” and “CvdS”)
If machine has not drained within 4 minutes 15
seconds, display flashes “Erdn”, time remaining, and
buzzer beeps. The buzzer stops beeping after 30
seconds while display flashes “Erdn” until machine
empties. If machine empties, ending Drain Error
condition, display stops flashing, buzzer turns off, and
remaining cycle time displays as the cycle resumes.
If machine does not empty, display continues flashing
“Erdn”. The drain error counter increases by one.
Refer to Cycle and Error Count section.

Clogged Filter (All C80 and C60 X Voltage
ONLY Models)
A clogged filter can cause the inverter drive to run at
an elevated temperature. If the control senses an
elevated inverter drive temperature, the bottom
indicator LED on front panel decal lights. Check and
clean the drive compartment filter if necessary. The
light turns off AFTER one cycle runs at normal
temperature.

Door Will Not Unlock
If the door solenoid cannot retract (unlocking the door)
at the end of the stop routine, the display will show
“----” for ten seconds. In all models except an early
version of the 125, control attempts to unlock the door
again by pulsing the door solenoid every ten seconds
for a total of five times. An early version of the 125
model has a door unlock button.
The display then flashes “CAnt”/“OPEn”, indicating it
cannot unlock the door. This indicates a problem, and
a qualified service technician should be consulted.
At the end of a cycle or at power up, before the control
will allow the door to unlock, control checks for low,
medium or high water level. Control allows the door to
unlock only when machine is empty. If any water level
is indicated, display shows “FULL” while keeping all
outputs off. This condition could indicate a slow drain
system or a mechanical blockage of the drain. Contact
an authorized service person, mentioning display on
control.

On Board Battery Problem
If certain functions require the on board battery
(dependent on specific machines) and if battery charge
is low, or battery is removed, the control will display
“bAtt”. This is displayed several seconds after power
is applied to the control. Contact an authorized service
person if condition continues.

F232157

Temperature Probe Malfunction
If display shows “+SFL”, “-19C”, or “00F”, the
temperature probe may need to be replaced. If problem
persists after changing probe, contact an authorized
service person.

Rapid Advance (For Models With
Firmware ID Code “C2dS” and
“CvdS”)
Enabling Rapid Advance
NOTE: Rapid Advance can only be used during a
cycle operation.
To enable Rapid Advance while a cycle is in progress,
machine must be in PROGRAM Mode. Refer to
Entering Program Mode.

How to Rapid Advance During All Steps
(Except First Fill Step)
1. Make sure Rapid Advance is enabled.
2. Enter PROGRAM Mode. Refer to Entering
Program Mode.
3. Press the Advance (∧) keypad to advance to
desired step.
4. Display will show recalculated time remaining.

How to Rapid Advance (During First Fill
Step)
1. Make sure Rapid Advance is enabled.
2. While machine is filling with water, enter
PROGRAM Mode. Refer to Entering Program
Mode.
3. To advance to the next step, press START
(Enter) keypad to turn off the ability to change
cycles.
4. Press the Advance (∧) keypad to advance to
desired step.
5. Display will show recalculated time remaining.
NOTE: If control is set up for ‘Etin’, the remaining
cycle time after using Rapid Advance step is
calculated as if control was configured for ‘Ptin’.
This is because any time estimations following
advance would be inaccurate. After the cycle ends,
and the ADVANCE Mode is disabled, the next cycle
display remaining cycle time based on the ‘Etin’
configuration.

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

27

Programming

Agitation Step

Test Cycle

Advance the cycle by pressing “∧” keypad to skip to
the drain step. Filling, supply flushing and other
signals turn off. Cycle remaining time is recalculated
as the total remaining time after the agitation.

The test cycle provides a convenient means of
troubleshooting and testing all machine functions
quickly.

Drain Step
Advance the cycle by pressing “∧” keypad to skip the
drain step and the following spin step. The spin step is
skipped because the drain step needs to be completed
to balance the load. The next programmed step after
the spin begins. Cycle remaining is recalculated as the
total remaining time after the drain and spin steps.
Spin Step
Advance the cycle by pressing “∧” keypad to skip the
spin step. The next step after the spin begins. Cycle
remaining is recalculated as the total remaining time
after the spin step.

Temporary Free Mode
An authorized operator can enable a Free Cycle
operation that overrides the programmed vend start
amount. After running the Free Cycle, which can be
any of the eight cycles, the control reverts to the usual
programmed vend.
NOTE: The cycle counter DOES count the free
cycle.
• To run a temporary Free Cycle, follow the steps
below. Enter PROGRAM Mode. Display shows
“0000” or temperature or “tSFL” (depending on
version of control).

1. Enter PROGRAM Mode. Display shows “0000”
or temperature or “tSFL” (depending on version
of control).
2. Press the (∨) keypad. Display shows “FrEE”.
3. Press the START (Enter) keypad. Display shows
“tESt”.
4. Return the Program/Run switch to the right.
Display will show the vend price.
5. Enter coins or make payment so that the vend
amount counts down. When vend is satisfied, the
display will show “tESt” and the START (Enter)
keypad LED will flash on and off. Press the
START (Enter) keypad to begin the test cycle.
6. Press START (Enter) keypad. The door locks and
the TEST Mode starts.
7. Display shows “SPC?”. This is a special factory
test procedure. Simply ignore it and the machine
will advance into the test cycle after about
five seconds or go to “bAL?” if variable-speed.
NOTE: For variable-speed models ONLY, display
shows “bAL?”. This is a factory test. Disregard the
display. Machine will begin the test cycle after a
few seconds.

• Press the (∨) keypad. Display shows “FrEE”.
• While display shows “FrEE”, return the
Program/Run switch to the RUN position. Then
press a cycle keypad to select one of the eight
cycles. Press START (Enter) to begin the cycle.
When the cycle concludes, vend reverts to the
programmed amount.

28

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Programming

Permanent Factory Diagnostic Test
Cycle
Warm fill to low water level

Display flashes “bFIL”/ “LO” (keypad WASH LED on), no agitation
Outputs: Motor OFF, Drain closed, hot fill on, cold fill on

Pause after reaching low
water level

Display shows “LO” (no flashing), LOW water level dot ON, no agitation (keypad WASH
LED on); pauses until operator presses (∧) keypad
Outputs: Motor OFF, Drain closed

Drain (can advance to next
step by pressing (∧) keypad
here)

Display shows “drAI”, no agitation (keypad WASH LED on)

Cold fill to medium level

Display flashes “CFIL”/ “nEd” (keypad WASH LED on), no agitation.

Outputs: Motor OFF, Drain open

Outputs: Motor OFF, Drain closed, cold fill on
Display shows “nEd” (no flashing), LOW and MEDIUM water level dots ON no agitation
(keypad WASH LED on); pauses until operator presses ^ keypad

Pause after reaching
medium water level

Outputs: Motor OFF, Drain closed
Hot fill to high level

Display flashes “HFIL”/ “HI” (keypad WASH LED on), no agitation.

Pause after reaching high
water level

Display shows “HI” (no flashing), LOW, MEDIUM, & HIGH water level dots ON, no
agitation (keypad WASH LED on); pauses until operator presses ^ keypad

Outputs: Motor OFF, Drain closed, hot fill on

Outputs: Motor OFF, Drain closed
Heat to 45°C (110°F)
SKIPS THIS STEP if
machine does not have heat
capability (“noHt” selected
in SETUP Mode)

Display flashes “HEAT” and the temperature inside the machine while agitating in forward
and reverse; continues until temperature reaches 45°C (110°F), then advances to next step.
(keypad WASH LED on)

Extra fill spare – 5 seconds
(skips this if not selected in
SETUP Mode)

Display flashes “EFIL” (keypad RINSE LED on)

Supply 1: 5 seconds (Heat
signal also on (IF at least
low water level – verifies
output even if not heated
model)

Display shows “SUP1” (keypad WASH LED on)

Supply 2: 5 seconds (Heat
on also)

Display shows “SUP2” (keypad ADD BLEACH LED on)

Supply 3: 5 seconds (Heat
on also)

Display shows “SUP3” (keypad RINSE LED on)

Pause 5 seconds, then
Forward wash speed –
2 minutes

Display shows “For”

Outputs: Motor alternates forward 12 seconds, off 3 seconds, reverse 12 seconds, off
3 seconds and repeats; Drain closed; Heat ON UNTIL 45°C (110°F) reached
Outputs: Motor alternates forward 12 seconds, off 3 seconds, reverse 12 seconds, off
3 seconds and repeats; Drain closed; “S4” output ON.
Outputs: Motor alternates forward 12 seconds, off 3 seconds, reverse 12 seconds, off
3 seconds and repeats; Drain closed; Supply 1 ON, HT ON, cold fill ON

Outputs: Motor alternates forward 12 seconds, off 3 seconds, reverse 12 seconds, off
3 seconds and repeats; Drain closed; Supply 2 ON, HT ON, cold fill ON
Outputs: Motor alternates forward 12 seconds, off 3 seconds, reverse 12 seconds, off
3 seconds and repeats; Drain closed; Supply 3 ON, HT ON, cold fill ON
Outputs: Motor operates wash speed forward; drain closed
Table 4 (Continued)

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

29

Programming
Table 4 (Continued)
Pause 5 seconds, then
Reverse wash speed –
2 minutes, then pause
several seconds before
entering drain (next step)

Display shows “rEv”

Drain (cannot advance to
spin here)

For 2 speed models: Display flashes “drAI”/ “For” (keypad RINSE LED on)
For variable-speed models: Display flashes “drAI”/ “For” while operating in low speed
forward; then flashes “drAI”/ “dISt” while operating at distribution speed.
If balance fails, repeats the “drAI”/ “For” then “drAI”/ “dISt” sequence above and balance
indicator is on during “drAI”/ “For” message (rebalance attempt). Tries up to 10 times in
TEST cycle then aborts test cycle.

Outputs: Motor operates wash speed reverse; drain closed

Outputs: Drain closed for first part of step (less than 20 seconds), then drain off.
2 speed models: Wash speed forward
Variable-speed: Forward during “drAI”/ “For”; distribution during “drAI”/ “dISt”.
Spin – 3 minutes

For 2 speed models: display shows “SPn” (keypad SPIN LED on)
For variable-speed models: display shows “SPn1” (keypad SPIN LED on)
Outputs: Spin (low spin for variable speed-see motor chart below)(*)

Highest Spin speed
(variable-speed models
ONLY) – 3 minutes

For 2 speed models: this step is skipped (goes to coast, the next step)
For variable-speed models: display shows “SPn2” (keypad SPIN LED on)

Coast

Displays “SdLY” (spin delay coast)

Outputs: Highest spin speed selected (see motor chart below)(*)
Outputs: all off

Stop routine.

Display shows “01” (1 minute remaining). Agitates briefly then unlocks the door, shows
“dOnE” while sounding the buzzer 10 seconds; “dOnE” shows for 20 more seconds.
(DOOR LED on while showing “dOnE”, meaning “door ready to open”).
Table 4

(*) For certain 125 models, the RPM may display.

NOTE: ON appears ONLY where motor control
outputs are on (otherwise they are off). Outputs
referenced are on control unit fuse board. Outputs
are as labeled on the fuse board.
Motor Speed Chart
Variable-speed motor control outputs – 2 speed motor outputs
applies only for variable-speed models
STF

STR

RH

RM

RL

Fwd

Rev

Spin

Motor off (no rotation)
Wash speed forward

ON

Wash speed reverse

ON
ON

Distribution (variable-speed ONLY)

ON

Spin (low spin speed “SPn1” for variablespeed)

ON

Highest spin (“SPn2” – variable-speed ONLY)

ON

ON

ON

ON

ON

NA
ON

ON

NA

ON
ON

NA
ON

NA

NA

NA

NA – Not Applicable
Table 5

NOTE: For variable-speed machines smaller than
C80, SPn1 and SPn2 are not the same speed.
30

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Programming

Cycle Charts
Domestic Coin Cycles
Cycle Steps
Cycle reference (display in
PROGRAM Mode)
Agitation (sec)
Wash 1 (WASH LED)
Time for agitation (min.)
Fill valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if “drain”) seconds

CY04

Perm
Press
Warm
CY05

Perm
Press
Cold
CY06

12/3/12
Normal

12/3/12
Normal

12/3/12
Normal

4
Hot

6
Hot

Low
2
Yes

Normal
Hot

Normal
Warm

Quick
Hot

Heavy
Soil

Quick
Warm

Delicate
Cold

CY01

CY02

CY03

CY07

CY08

12/3/12
Normal

12/3/12
Normal

12/3/12
Normal

12/3/12
Normal

3/12/3
Gentle

4
Hot
Low
2

4
Both
(warm)
Low
2

4
Cold
Low
2

4
Both
(warm)
Low
2

4
Cold

Low
2

4
Both
(warm)
Low
2

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Med
2

Wash 2 (WASH LED)
Time for agitation (min.)
Fill valves (temperature)
Fill water level
Supply
Heat (if enabled)
Cooling or no cooling
Drain
Spin (only if “drain”) seconds
Wash 3 (WASH LED)
Time for agitation (min.)
Fill valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if “drain”) seconds
Wash 4 (WASH LED)
Time for agitation (min.)
Fill valves (temperature)
Fill water level
Supply
Drain
Spin (only if “drain”) seconds
Table 6 (Continued)

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

31

Programming
Table 6 (Continued)
Cycle Steps

Normal
Hot

Normal
Warm

Quick
Hot

Heavy
Soil

Perm
Press
Warm

Perm
Press
Cold

Quick
Warm

Delicate
Cold

2

2

2

3

2

2

2

2

Agitation in effect for cycle
Rinse 1 (RINSE LED)
Time for agitation (min.)
Fill valves (temperature)

Cold

Cold

Cold

Cold

Cold

Cold

Cold

Cold

Fill water level

High

High

High

High

High

High

High

High

Supply

0

0

0

0

0

0

0

0

Drain

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Time for agitation (min.)

2

2

2

2

2

Fill valves (temperature)

Cold

Cold

Cold

Cold

Cold

Cold

Fill water level

Low

Low

Low

Low

Low

High

Supply

0

0

0

0

0

3

Drain

Yes

Yes

Yes

Yes

Yes

Yes

Spin (only if “drain”) seconds
Rinse 2 (RINSE LED)
2

Spin (only if “drain”) seconds

120

Rinse 3 (RINSE LED)
Time for agitation (min.)
Fill valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if “drain”) seconds
Rinse 4 (RINSE LED)
Time for agitation (min.)

2

2

2

2

2

2

2

Fill valves (temperature)

Cold

Cold

Cold

Cold

Cold

Cold

Cold

Fill water level

Low

Low

High

Low

Low

Low

High

3

3

3

3

3

3

3

Yes

Yes

Yes

Yes

Yes

Yes

Yes

4

4

4
Table 6

4

3

3

3

Supply
Heat (if enabled)
Drain
Spin (only if “drain”) minutes

32

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157

Programming

International Coin Cycles
Cycle Steps
Agitation
Wash 1 (WASH LED)
Time for agitation (min.)
Fill valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if “drain”) minutes
Wash 2 (WASH LED)
Time for agitation (min.)
Fill valves (temperature)

Normal
95°C

Normal
60°C

Normal
40°C

Gentle
Cold

Perm
Press
95°C

Perm
Press
60°C

12/3/12
Normal

12/3/12
Normal

12/3/12
Normal

3/12/3
Gentle

12/3/12
Normal

12/3/12
Normal

Default
Perm
Press
40°C
3/12/3
Gentle

Gentle
30°C
3/12/3
Gentle

2

2

2

2

2

2

2

2

Both
(warm)
Low
1
40°C
Yes
0

Both
(warm)
Low
1
40°C
Yes
0

Both
(warm)
Low
1
40°C
Yes
0

Cold

Both
(warm)
Low
1
40°C
Yes
0

Both
(warm)
Low
1
40°C
Yes
0

Both
(warm)
Low
1
40°C
Yes
0

Cold

6
Hot

6
Both
(warm)
Low
6
40°C
No
0

6
Hot
Low
6
95°C
No
0

6
Both
(warm)
Low
6
60°C
No
0

6
Both
(warm)
Low
6
40°C
No
0

2
Cold
High
0
No
Yes
0

2
Cold
High
0
No
Yes
0

2
Cold
High
0
No
Yes
0

2
Cold
High
0
No
Yes
0

Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if “drain”) minutes

Low
6
95°C
No
0

6
Both
(warm)
Low
6
60°C
No
0

Wash 3 (WASH LED)
Time for agitation (min.)
Fill valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if “drain”) minutes

2
Cold
High
0
No
Yes
0

2
Cold
High
0
No
Yes
0

High
1
0
Yes
0

High
1
0
Yes
0

3
Cold
High
6
30°C
Yes
0

Wash 4 (WASH LED)
Time for agitation (min.)
Fill valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if “drain”) minutes
Table 7 (Continued)

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

33

Programming
Table 7 (Continued)
Normal
95°C

Normal
60°C

Normal
40°C

Gentle
Cold

Perm
Press
95°C

Perm
Press
60°C

Default
Perm
Press
40°C

Gentle
30°C

12/3/12
Normal

12/3/12
Normal

12/3/12
Normal

3/12/3
Gentle

12/3/12
Normal

12/3/12
Normal

3/12/3
Gentle

3/12/3
Gentle

Time for agitation (min.)

2

2

2

2

2

2

2

Fill valves (temperature)

Cold

Cold

Cold

Cold

Cold

Cold

Cold

Fill water level

High

High

High

High

High

High

High

0

0

0

0

0

0

0

Heat

No Heat

No Heat

No Heat

No Heat

No Heat

No Heat

No Heat

Drain

Yes

Yes

Yes

Yes

Yes

Yes

Yes

0

0

0

0

0

0

0

Time for agitation (min.)

2

2

2

2

2

2

2

2

Fill valves (temperature)

Cold

Cold

Cold

Cold

Cold

Cold

Cold

Cold

Fill water level

High

High

High

High

High

High

High

High

0

0

0

0

0

0

0

0

Heat

No Heat

No Heat

No Heat

No Heat

No Heat

No Heat

No Heat

No Heat

Drain

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Spin (only if “drain”) seconds

60

60

60

60

60

60

60

60

Time for agitation (min.)

3

3

3

3

3

3

3

3

Fill valves (temperature)

Cold

Cold

Cold

Cold

Cold

Cold

Cold

Cold

Fill water level

High

High

High

High

High

High

High

High

Cycle Steps
Agitation
Rinse 1 (RINSE LED)
Time for agitation (min.)
Fill valves (temperature)
Fill water level
Supply
Drain
Spin (only if “drain”) seconds
Rinse 2 (RINSE LED)

Supply

Spin (only if “drain”) seconds
Rinse 3 (RINSE LED)

Supply

Rinse 4 (RINSE LED)

Supply

3

3

3

3

3

3

3

3

Heat

No Heat

No Heat

No Heat

No Heat

No Heat

No Heat

No Heat

No Heat

Drain

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

5

5

5

2

3

3

3

2

Spin (only if “drain”) minutes

Table 7

34

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Mode                       : UseNone
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Create Date                     : 2009:08:18 08:40:48Z
Creator Tool                    : FrameMaker 9.0
Modify Date                     : 2009:08:20 08:56:46-05:00
Metadata Date                   : 2009:08:20 08:56:46-05:00
Format                          : application/pdf
Description                     : F232157R7
Creator                         : Alliance Laundry Systems
Title                           : Programming for Washer-Extractors
Copyright                       : © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Document ID                     : uuid:63716d3e-8aeb-4331-915c-d38ec98efa49
Instance ID                     : uuid:8a1acc36-5fd0-47cc-9f47-9cc8870d2b9e
Page Count                      : 36
Page Layout                     : SinglePage
Author                          : Alliance Laundry Systems
Subject                         : F232157R7
EXIF Metadata provided by EXIF.tools

Navigation menu