Alpha Networks 2006050055-1 Wireless miniPCI Card User Manual users manual

Alpha Networks Inc. Wireless miniPCI Card users manual

users manual

iMP54G5 (MS-6833B)Wireless 11g MiniPCI CardUser’s Guide
Federal Communications Commission (FCC) Caution 1. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. FCC RF Radiation Exposure Statement: The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. 3.The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique＂ antenna coupler (at all connections between the module and the antenna, including the cable). Any antenna used with the module must be approved with the module, either at the time of initial authorization or through a Class II permissive change. The “professional installation＂ provision of Section 15.203 may not be applied to modules. 5.Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. 6.The modular transmitter must be labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “ Contains Transmitter Module FCC ID:XYZMODEL1” or “Contains FCC ID:XYZMODEL1.” Federal Communications Commission (FCC) Statement All Antennas listed below have to be provided to the OEM for his use. No other antennas are authorized to be used by the OEM except listed in the Manual. No. Model # Type of Ant. 1 505900000110 DIPOLE 2 5059000090110G DIPOLE 3 YQ-Z009-0545 DIPOLE 4 RFA-02-3-C5H1-06-50 DIPOLE 5 RFA-02-3-C5M3 DIPOLE 6 RFA-02-5-F7H1-06-50 DIPOLE 7 M560A SK560WIPI01A PIFA 8 M540G K05007000403 PIFA 9 M30 PIFA 10 C05092208_1 PIFA 11 THW1139A1 PIFA 12 EY1002430060R DIPOLE 13 THW1252A1 DIPOLE Ï
This device is intended only for OEM integrators under the following: 1) The antenna must be installed such that 20cm is maintained between antenna and users 2) The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. As long as 2 conditions above are met, further transmitter test will not required. However, the OEM integrator is still responsible for testing end-product for any additional compliance requirements required with module installed (for example, digital device emissions, P peripheral requirements, etc.) Important Note In the event that these conditions can not be example certain laptop configurations or co-location with another transmitter, then the FCC authorization is no longer considered valid because the FCC ID can not be used on the final product. In these circumstances, OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. ⅱ
iiiManual Information for End UsersThe end user must not have manual instructions to remove or install device. The usermanual for end users must include the following information in a prominent location:“IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements,the antenna used for this transmitter must be installed to provide a separation distance ofat least 20 cm from all persons and must not be co-located operating in conjunction withany other antenna or transmitter.” as a result of e-mail transmission.”Important Safety PrecautionsAlways read and follow these basic safety precautions carefully when handling anypiece of electronic component.1. Keep this User’s Guide for future reference.2. Keep this equipment away from humidity.3. Lay this equipment on a reliable flat surface before setting it up.4. The openings on the enclosure are for air convection hence protects theequipment from overheating.5. All cautions and warnings on the equipment should be noted.6. Never pour any liquid into the opening that could damage or cause electricalshock.7. If any of the following situations arises, get the equipment checked by aservice personnel:Liquid has penetrated into the equipmentThe equipment has been exposed to moistureThe equipment has not work well or you can not get it work according to User’s ManualThe equipment has dropped and damagedIf the equipment has obvious sign of breakage8. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENTUNCONDITIONED, STORAGE TEMPERATURE ABOVE 60O C ORBELOW -20OC, IT MAY DAMAGE THE EQUIPMENT.
1IntroductionMSI MP54G5, the Wireless 11g miniPCI Card, is a Type IIIBcard, which can be used to integrate with such systems asnotebook, mini-barebone and portable PC. With MSI MP54G5embedded inside, a system could provide users with the abilityand flexibility to connect up to Internet wirelessly via 802.11gwith speed up to 54Mbps.MSI MP54G5 is taking advantage of leading technologies fromRalink. It addresses WLAN (Wireless Local Area Network) mar-kets by providing true simultaneous connectivity while deploy-ing IEEE 802.11g. Along with this solution, a system installed ina single card is able to offer capability of WiFi mode. It willbenefit system vendors in miniaturization of system dimensionand BOM cost reduction, as well as also make users happy withthe all-in-one functionality.>>> 1.1 MP54G5 (MS-6833B) - MiniPCI Card
2Ad-hoc Mode : An Ad-hoc network is a local area network orother small network, especially one with wireless or temporaryplug-in connections, in which some of the network devices arepart of the network only for the duration of a communicationssession. Users in the network can share files, print to a sharedprinter, and access the Internet with a shared modem. In thiskind of network, new devices can be quickly added; however,users can only communicate with other wireless LAN comput-ers that are in this wireless LAN workgroup, and are withinrange.>>> 1.2 How MP54G5 WorksIn WLAN Environment1.2.1MP54G5 MP54G5WLAN MiniPCI Card WLAN MiniPCI Card
3Infrastructure Mode : The difference between Infrastructurenetwork and Ad-hoc network is that the former one includes anAccess Point. In an Infrastructure network, the Access Point canmanage the bandwidth to maximize bandwidth utilization. Addi-tionally, the Access Point enables users on a wireless LAN toaccess an existing wired network, allowing wireless users to takeadvantage of the wired networks resources, such as Internet,email, file transfer, and printer sharing. The scale and range of theInfrastructure networking are larger and wider than that of theAd-hoc networking.MP54G5 MP54G5WLAN MiniPCI CardWLAN MiniPCI Card
4>>> 1.3 SpecificationsForm Factor 32-bit Type IIIBOperation voltage 3.3VAntenna Connector Two antenna connectorsOperating System Microsoft® Windows® 98SE/ME/2000/XPEnvironmental - Operating Temperature: 0 ~ 55OC- Operating Humidity: 10 ~ 90%, non-condensingDimensions (WxDxH)59.75 x 44.6 x 3.5mmNetwork Standard IEEE 802.11; IEEE 802.11b/gFrequency Band 2.412-2.484 GHzData Rate IEEE 802.11g (auto-fallback):- OFDM: 54, 48, 36, 24, 18, 12, 9 and 6MbpsIEEE 802.11b (auto-fallback):- CCK: 11, 5.5 Mbps- DQPSK: 2 Mbps- DBPSK: 1 MbpsMedia Access ControlCSMA/CA with ACKTransmission DSSS (direct sequential spreadspectrum)Network ArchitectureAd-Hoc Mode (Peer-to-Peer);Infrastructure ModeAntenna Type Two antenna connectors supportPower Consumption TX peak: 350mA RX peak: 260mAIdle:5mAStandby: 160mA Hardware Specification WLAN Specification
5Channel IEEE 802.11g:Ch. 1-11 – N. AmericaCh. 1-13 – JapanCh. 1-13– Europe ETSICh. 10-11 – SpainCh. 10-13 – FranceIEEE 802.11b:Ch. 1-11 – N. AmericaCh. 1-13 – JapanCh. 1-13– Europe ETSICh. 10-11 – SpainCh. 10-13 – FranceOutput Power Output Power11b: 18dBm+/-2 Max 11g: 14dBm+/-2 MaxReceiver Sensitivity 54 Mbps OFDM @ 10% PER = -65 dBm(Average Value) 48 Mbps OFDM @ 10% PER = -66 dBm36 Mbps OFDM @ 10% PER = -70 dBm24 Mbps OFDM @ 10% PER = -74 dBm18 Mbps OFDM @ 10% PER = -77 dBm12 Mbps OFDM @ 10% PER = -79 dBm11 Mbps CCK @ 8% PER = -80 dBm9 Mbps OFDM @ 10% PER = -81 dBm6 Mbps OFDM @ 10% PER = -82 dBm5.5 Mbps CCK @ 8% PER = -82 dBm2 Mbps QPSK @ 8% PER = -83 dBm1 Mbps BPSK @ 8% PER = -83 dBm
6>>> 1.4 System RequirementsBefore installing MP54G5, your PC should meet the followingitems:- One desktop/notebook PC with an available MiniPCI slot.- Windows® 98SE/ME/2000/XP operating system.- Minimum 5MB free disk space for installing the driver and utilities.- One CD-ROM drive, double speed or higher.>>> 1.5 Package ContentsUnpack the package and check all the items carefully. If any itemcontained is damaged or missing, please contact your local dealeras soon as possible. Also, keep the box and packing materials incase you need to ship the unit in the future. The package shouldcontain the following items:- One Wireless 11g MiniPCI Card.- One Installation CD-ROM including drivers, utilities, and the manual files.
7>>> 1.6 Product ViewGolden FingerWLAN 11g antenna connectorsConnect to external antennas forenhanced data transmission andreception. The external antennas arewell designed on the desktop or note-book computers.
8Hardware Installation 1. Locate the MiniPCI slot on the mainboard.Place yourMP54G5 over the MiniPCI slot (at an angle of 30degrees). Then, gently insert it into the slot until thegolden finger of the card gets fully inserted. 2. Press down the card, and the retaining clips (on twosides of the slot) will lock onto the notches of the card. 3. Connect the attenna’s cable to the connector on the card.The following diagrams provide you a basic installation for yourMP54G5. The instruction below is suitable for most computerswith MiniPCI slot. For more information about the MiniPCImodule, please refer to your computer’s manual.Installing MP54G5:
9Software InstallationThis chapter describes the procedures of installing the driverand utility. Follow the instruction step by step to finish theinstallation. If you use Windows® 98SE/ME, please preparethe Windows® Setup CD at hand before installing the driver;because the system will ask you to insert the Setup CD to copyfiles during the installation.Please NOTE that the MP54G5 should be installed into yourcomputer before installing the driver and utility. Then, theoperating system will detect a new device and start to configurethe new device. Click Cancel here to start installation from theInstallShield Wizard.ClickTip: The MP545 adapter shouldbe installed into your PC beforeinstalling the driver and utility.The adapter model you installed
10Insert the software CD into your CD-ROM drive, and the Setupprogram should launch automatically.If the Autorun program doesn’t launch automatically, click Startat the taskbar and select Run.... Type E:\setup.exe (where E isyour CD-drive) in the Open box and click OK to launch theSetup program manually.The main screen of Setup program will appear as below. 1. Click the Install WLAN Driver button. 2. The welcome screen of InstallShield Wizard appears.Click Next. 3. Read and accept the License Agreement; then, click Next. 4. Click Install and the program will copy the necessaryfiles to the system. The progress indicator shows theinstalling status. 5. Click Finish when the WLAN driver installation iscompleted.STEP1STEP2

Navigation menu