Alpha Networks 2006050055-1 Wireless miniPCI Card User Manual users manual
Alpha Networks Inc. Wireless miniPCI Card users manual
users manual
MP54G5 (MS-6833B) Wireless 11g MiniPCI Card User’s Guide Federal Communications Commission (FCC) Caution 1. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. FCC RF Radiation Exposure Statement: The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. 3.The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique" antenna coupler (at all connections between the module and the antenna, including the cable). Any antenna used with the module must be approved with the module, either at the time of initial authorization or through a Class II permissive change. The “ professional installation" provision of Section 15.203 may not be applied to modules. 5.Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. 6.The modular transmitter must be labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “ Contains Transmitter Module FCC ID:XYZMODEL1” or “Contains FCC ID:XYZMODEL1.” Federal Communications Commission (FCC) Statement All Antennas listed below have to be provided to the OEM for his use. No other antennas are authorized to be used by the OEM except listed in the Manual. No. 10 11 12 13 Model # 505900000110 5059000090110G YQ-Z009-0545 RFA-02-3-C5H1-06-50 RFA-02-3-C5M3 RFA-02-5-F7H1-06-50 M560A SK560WIPI01A M540G K05007000403 M30 C05092208_1 THW1139A1 EY1002430060R THW1252A1 Ï Type of Ant. DIPOLE DIPOLE DIPOLE DIPOLE DIPOLE DIPOLE PIFA PIFA PIFA PIFA PIFA DIPOLE DIPOLE This device is intended only for OEM integrators under the following: 1) The antenna must be installed such that 20cm is maintained between antenna and users 2) The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. As long as 2 conditions above are met, further transmitter test will not required. However, the OEM integrator is still responsible for testing end-product for any additional compliance requirements required with module installed (for example, digital device emissions, P peripheral requirements, etc.) Important Note In the event that these conditions can not be example certain laptop configurations or co-location with another transmitter, then the FCC authorization is no longer considered valid because the FCC ID can not be used on the final product. In these circumstances, OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. ⅱ Manual Information for End Users The end user must not have manual instructions to remove or install device. The user manual for end users must include the following information in a prominent location: “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located operating in conjunction with any other antenna or transmitter.” as a result of e-mail transmission.” Important Safety Precautions Always read and follow these basic safety precautions carefully when handling any piece of electronic component. 1. Keep this User’s Guide for future reference. 2. Keep this equipment away from humidity. 3. Lay this equipment on a reliable flat surface before setting it up. 4. The openings on the enclosure are for air convection hence protects the equipment from overheating. 5. All cautions and warnings on the equipment should be noted. 6. Never pour any liquid into the opening that could damage or cause electrical shock. 7. If any of the following situations arises, get the equipment checked by a service personnel: Liquid has penetrated into the equipment The equipment has been exposed to moisture The equipment has not work well or you can not get it work according to User’s Manual The equipment has dropped and damaged If the equipment has obvious sign of breakage 8. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 60 O C OR BELOW -20 OC, IT MAY DAMAGE THE EQUIPMENT. iii Introduction >>> 1.1 MP54G5 (MS-6833B) - MiniPCI Card MSI MP54G5, the Wireless 11g miniPCI Card, is a Type IIIB card, which can be used to integrate with such systems as notebook, mini-barebone and portable PC. With MSI MP54G5 embedded inside, a system could provide users with the ability and flexibility to connect up to Internet wirelessly via 802.11g with speed up to 54Mbps. MSI MP54G5 is taking advantage of leading technologies from Ralink. It addresses WLAN (Wireless Local Area Network) markets by providing true simultaneous connectivity while deploying IEEE 802.11g. Along with this solution, a system installed in a single card is able to offer capability of WiFi mode. It will benefit system vendors in miniaturization of system dimension and BOM cost reduction, as well as also make users happy with the all-in-one functionality. >>> 1.2 How MP54G5 Works 1.2.1 In WLAN Environment Ad-hoc Mode : An Ad-hoc network is a local area network or other small network, especially one with wireless or temporary plug-in connections, in which some of the network devices are part of the network only for the duration of a communications session. Users in the network can share files, print to a shared printer, and access the Internet with a shared modem. In this kind of network, new devices can be quickly added; however, users can only communicate with other wireless LAN computers that are in this wireless LAN workgroup, and are within range. MP54G5 MP54G5 WLAN MiniPCI Card WLAN MiniPCI Card Infrastructure Mode : The difference between Infrastructure network and Ad-hoc network is that the former one includes an Access Point. In an Infrastructure network, the Access Point can manage the bandwidth to maximize bandwidth utilization. Additionally, the Access Point enables users on a wireless LAN to access an existing wired network, allowing wireless users to take advantage of the wired networks resources, such as Internet, email, file transfer, and printer sharing. The scale and range of the Infrastructure networking are larger and wider than that of the Ad-hoc networking. MP54G5 MP54G5 WLAN MiniPCI Card WLAN MiniPCI Card >>> 1.3 Specifications Hardware Form Factor Specification Operation voltage 32-bit Type IIIB 3.3V Antenna Connector Two antenna connectors Operating System Microsoft® Windows® 98SE/ME/2000 /XP Environmental - Operating Temperature: 0 ~ 55OC - Operating Humidity: 10 ~ 90%, non-condensing Dimensions (WxDxH) 59.75 x 44.6 x 3.5mm Network Standard WLAN Specification Frequency Band IEEE 802.11; IEEE 802.11b/g 2.412-2.484 GHz Data Rate IEEE 802.11g (auto-fallback): - OFDM: 54, 48, 36, 24, 18, 12, 9 and 6Mbps IEEE 802.11b (auto-fallback): - CCK: 11, 5.5 Mbps - DQPSK: 2 Mbps - DBPSK: 1 Mbps Media Access Control CSMA/CA with ACK Transmission DSSS (direct sequential spread spectrum) Network Architecture Ad-Hoc Mode (Peer-to-Peer); Infrastructure Mode Antenna Type Two antenna connectors support Power Consumption TX peak: 350mA Idle:5mA Standby: 160mA RX peak: 260mA Channel IEEE 802.11g: Ch. 1-11 – N. America Ch. 1-13 – Japan Ch. 1-13– Europe ETSI Ch. 10-11 – Spain Ch. 10-13 – France IEEE 802.11b: Ch. 1-11 – N. America Ch. 1-13 – Japan Ch. 1-13– Europe ETSI Ch. 10-11 – Spain Ch. 10-13 – France Output Power Output Power 11b: 18dBm+/-2 Max 11g: 14dBm+/-2 Max Receiver Sensitivity (Average Value) 54 Mbps OFDM @ 10% PER = -65 dBm 48 Mbps OFDM @ 10% PER = -66 dBm 36 Mbps OFDM @ 10% PER = -70 dBm 24 Mbps OFDM @ 10% PER = -74 dBm 18 Mbps OFDM @ 10% PER = -77 dBm 12 Mbps OFDM @ 10% PER = -79 dBm 11 Mbps CCK @ 8% PER = -80 dBm 9 Mbps OFDM @ 10% PER = -81 dBm 6 Mbps OFDM @ 10% PER = -82 dBm 5.5 Mbps CCK @ 8% PER = -82 dBm 2 Mbps QPSK @ 8% PER = -83 dBm 1 Mbps BPSK @ 8% PER = -83 dBm >>> 1.4 System Requirements Before installing MP54G5, your PC should meet the following items: - One desktop/notebook PC with an available MiniPCI slot. - Windows® 98SE/ME/2000/XP operating system. - Minimum 5MB free disk space for installing the driver and utilities. - One CD-ROM drive, double speed or higher. >>> 1.5 Package Contents Unpack the package and check all the items carefully. If any item contained is damaged or missing, please contact your local dealer as soon as possible. Also, keep the box and packing materials in case you need to ship the unit in the future. The package should contain the following items: - One Wireless 11g MiniPCI Card. - One Installation CD-ROM including drivers, utilities, and the manual files. >>> 1.6 Product View WLAN 11g antenna connectors Connect to external antennas for enhanced data transmission and reception. The external antennas are well designed on the desktop or notebook computers. Golden Finger Hardware Installation The following diagrams provide you a basic installation for your MP54G5. The instruction below is suitable for most computers with MiniPCI slot. For more information about the MiniPCI module, please refer to your computer’s manual. Installing MP54G5: 1. Locate the MiniPCI slot on the mainboard.Place your MP54G5 over the MiniPCI slot (at an angle of 30 degrees). Then, gently insert it into the slot until the golden finger of the card gets fully inserted. 2. Press down the card, and the retaining clips (on two sides of the slot) will lock onto the notches of the card. 3. Connect the attenna’s cable to the connector on the card. Software Installation This chapter describes the procedures of installing the driver and utility. Follow the instruction step by step to finish the installation. If you use Windows® 98SE/ME, please prepare the Windows® Setup CD at hand before installing the driver; because the system will ask you to insert the Setup CD to copy files during the installation. Please NOTE that the MP54G5 should be installed into your computer before installing the driver and utility. Then, the operating system will detect a new device and start to configure the new device. Click Cancel here to start installation from the InstallShield Wizard. The adapter model you installed Click Tip: The MP545 adapter should be installed into your PC before installing the driver and utility. ST EP 1 Insert the software CD into your CD-ROM drive, and the Setup program should launch automatically. If the Autorun program doesn’t launch automatically, click Start at the taskbar and select Run.... Type E:\setup.exe (where E is your CD-drive) in the Open box and click OK to launch the Setup program manually. The main screen of Setup program will appear as below. ST EP 2 1. Click the Install WLAN Driver button. 2. The welcome screen of InstallShield Wizard appears. Click Next. 3. Read and accept the License Agreement; then, click Next. 4. Click Install and the program will copy the necessary files to the system. The progress indicator shows the installing status. 5. Click Finish when the WLAN driver installation is completed. 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Print high-res Page Count : 14 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:902fde7c-6402-43eb-9834-098720191925 Producer : pdfFactory Pro 2.30 (Windows XP Professional Chinese) Create Date : 2005:07:08 10:59:24+08:00 Modify Date : 2006:09:04 11:27:01+08:00 Metadata Date : 2006:09:04 11:27:01+08:00 Creator Tool : pdfFactory Pro www.pdffactory.com Document ID : uuid:67bafdc6-085d-4ef0-94e8-b4968ed9bee3 Format : application/pdf Title : \\Manual_server\未完成備份\Kath Creator : kathychien Author : kathychienEXIF Metadata provided by EXIF.tools