Alpha Networks WUSN10A1 WIRELESS 150 USB ADAPTER User Manual WUS N10

Alpha Networks Inc. WIRELESS 150 USB ADAPTER WUS N10

Users Manual

Download: Alpha Networks WUSN10A1 WIRELESS 150 USB ADAPTER User Manual WUS N10
Mirror Download [FCC.gov]Alpha Networks WUSN10A1 WIRELESS 150 USB ADAPTER User Manual WUS N10
Document ID1269816
Application IDY5s5mD2zATo8NdYke52DuQ==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize0.97kB (12169 bits)
Date Submitted2010-04-20 00:00:00
Date Available2010-04-21 00:00:00
Creation Date2010-04-16 13:36:56
Producing SoftwareAcrobat Distiller 7.0 (Windows)
Document Lastmod2010-04-16 13:36:56
Document TitleMicrosoft Word - WUS-N10_User manual
Document CreatorPScript5.dll Version 5.2
Document Author: Jamy

Adapter Installation
1.
Turn on the computer and Insert the Alpha WUS-N10 Driver CD in the
CD-ROM drive
2.
When the auto run screen appears, click Install Drivers.
The InstallShield Wizard window will appear.
By default setup will install to the default location: To install to a different
3.
4.
5.
6.
7.
location click Browse and specify the location.
Select the Program Files folder location
Insert the adapter into an available USB port on your computer.
The Wireless Connection Wizard will now appear.
To connect to your network using the WPS push button configuration
method, click the virtual button as shown in the screenshot.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance.
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is
firmware-limited to channels 1 through 11.
Antennas must be installed to provide 20 cm separation distance from the
transmitting antenna to the body of the user during normal operating condition.
This device must not be co-located or operating in conjunction with any other
antenna or transmitter.
Only those antennas filed under FCC ID: RRKWUSN10A1 can be used with
this device.
When the module is installed in the final system where the antenna location is
less than 20 cm separation distance to the body of user, additional equipment
authorization must be applied.
FCC ID label on the final system must be labeled with “Contains FCC ID:
RRKWUSN10A1” or “Contains transmitter module FCC ID: RRKWUSN10A1”.
In the user guide, final system integrator must be ensure that there is no
instruction provided in the user guide to install or remove the transmitter
module.
The transmitter module must be installed and used in strict accordance with the
manufacturer's instructions as described in the user documentation that comes
with the product. This device complies with the following radio frequency and
safety standards.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2010:04:16 13:36:56+08:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2010:04:16 13:36:56+08:00
Format                          : application/pdf
Creator                         : Jamy
Title                           : Microsoft Word - WUS-N10_User manual
Document ID                     : uuid:9f95b478-af01-4cab-8b4c-a64da3153703
Instance ID                     : uuid:fb47d2b2-6675-48da-a204-ecb5ea659ce2
Page Count                      : 2
Author                          : Jamy
EXIF Metadata provided by EXIF.tools
FCC ID Filing: RRKWUSN10A1

Navigation menu