Altacogni SWTH1-1230 SWTH1-1230 User Manual Snoozy
Yanzi Networks AB SWTH1-1230 Snoozy
user manual Snoozy
Yanzi Networks reserve the right to change this specification at any time without notice. Disclaimer: Yanzi Networks can not guarantee that this specification is 100% correct. Product Brief Yanzi Smart Building Solution Yanzi Climate Yanzi Climate measures temperature and humidity indoor or outdoor. Yanzi Climate can be used as frost alarm in cirital places, for humidity monitoring in server rooms, for fridge monitoring in stores, or to measure outdoor temperature on a remote Location. Set a threshold to receive notifications over Cirrus API, SMS, or push notice if temperature or humidity limits are breached or keep track of temperature/humidity variations. Yanzi Climate connects wirelessly to Yanzi Gateway or Yanzi IoT Access Point in a secure way through Yanzi's “Zero-Touch configuration” and it can be immediately accessed through the Cirrus API or the Yanzi App. Yanzi Climate Product Brief Doc No: 890-07055 Ver: 02 Date: 2015-09-02 Highlights ● Simple to install - single tap encryption setup ● Provides temperature and relative humidity ● Easily mounted on walls or standing on a shelf Measurement Range ● Humidity 0% to 100% RH ● Temperature -30°C to +60°C Measurement Accuracy ● Humidity ±5% (20-80% RH) ● Temperature ±0.5°C (-10°C to +60°C) ±1°C (-30°C to -10°C) Power ● 4 pcs of 1.5V AA Lithium Li-Fe or 4 pcs of 1.5V AA Alkaline batteries ● Battery lifetime expectancy up to 10 years* Getting started Two steps to get started 1. Plug in batteries Yanzi Networks reserve the right to change this specification at any time without notice. Disclaimer: Yanzi Networks can not guarantee that this specification is 100% correct. Specifications 2. Accept over Cirrus or in Yanzi App You are now ready to interact with your Yanzi Climate Wireless Performance: ● IEEE 802.15.4 2.4GHz IPv6 Sensor Network supporting Mesh Technology ● Wireless Output Power 3dBm - 8dBm (~2 - 6.3mW) ● Wireless Range 5-25m indoor, 50 - 100m Line of Sight (Indicative) ● Omnidirectional internal antenna, 0.5dBi peak gain ● ECC/AES encryption. High security with unique encryption keys for each Yanzi Climate - automatically installed at setup Environmental Requirements ● Operating Requirements -30°C to +60°C, 0 - 100% RH(non-condensing) Indoor and protected outdoor ● Storage Requirements 0°C to +50°C, 20 - 80% RH(non-condensing) ● IP42 protection Designed for vertical mounting when outdoors External Buttons ● Status (press to show status on LED) ● Reset (press and hold for >20 s) Dimensions ● 96 x 62 x 29 mm Ordering Information SWTH1-1230 Yanzi Climate * To ensure long battery life, Lithium batteries are required, especially in conditions with temperatures below 0°C For instructions and information about safety, warranty, and recycling, please visit www.yanzinetworks.com Yanzi Climate Product Brief Doc No: 890-07055 Ver: 02 Date: 2015-09-02 Caution: This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Doc No: 864-02049, Rev 1
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : Stefan Sandhagen Description : Title : Create Date : 2015:10:15 14:45:12+02:00 Creator Tool : Microsoft® Visio® 2010 Modify Date : 2016:02:04 13:28:33+08:00 Metadata Date : 2016:02:04 13:28:33+08:00 Keywords : Producer : Microsoft® Visio® 2010 Document ID : uuid:f6388f4c-e895-4e42-9fc3-f748ae969ce7 Instance ID : uuid:8e43f6fb-c06c-4b82-bde4-11c399009d59 Page Count : 3 Author : Stefan Sandhagen Subject :EXIF Metadata provided by EXIF.tools