Altai Technologies CX200 CX200 Outdoor 2x2 802.11ac Wave 2 AP User Manual CX200 Quick Setup Guide

Download:
Mirror Download [FCC.gov]
Document ID	4127578
Application ID	C6rxHZVMYmV2FI9OZWgSAw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	99.77kB (1247090 bits)
Date Submitted	2019-01-02 00:00:00
Date Available	2019-01-03 00:00:00
Creation Date	2018-12-22 15:37:54
Producing Software	Microsoft® Word 2013
Document Lastmod	2018-12-22 15:37:54
Document Title	CX200 Quick Setup Guide
Document Creator	Microsoft® Word 2013
Document Author:	Taylor Wan

Quick Setup Guide
Altai CX200 Outdoor 2x2
8 0 2 . 1 1 a c W a v e 2 AP
_________________________________________________
Quick Setup Guide
Version 1.1
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Introduction
Thank you for purchasing the Altai CX200 product. This guide provides
instructions to install the product and set it up as AP with minimal effort.
Package Contents
Detachable Antennae
- 2.4GHz Antenna x 2
CX200 Main Unit
Pole Mount
Hose Clamp
- 5GHz Antenna
x2
Wall Mount Kit
- Anchors
- Screws
Quick Setup Guide
Adhesive Label
x2
x2
PoE Injector
(Optional)
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Hardware Overview
LED Indicator
LED Indicator
Power
Off
AP powered off
Flashing Red
AP booting up
Solid Red
AP boot up finished and ready for
service
LAN (Ethernet)
Off
LAN disconnected
Solid Green
LAN connected
Flashing Green
Data Transmitting/Receiving
2.4 GHz/5G WiFi
Off
Radio Disabled
Radios
Solid Green
1. AP mode on but with no client
(AP/Station/
association; OR
Repeater/Bridge)
2. Station mode on but not
connected to remote AP; OR
3. Repeater mode on but not
connected to remote AP; OR
4. Bridge mode on but not
connected to remote peer
Flashing Green
Data transmitting/receiving
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Ethernet Port and RF Antenna Port
5GHz Dipole
2.4GHz Dipole
Antenna
Antenna
NOTE: To ensure correct
antenna connection, check
the labels (2.4GHz/5GHz)
printed on each antenna
body and RF port for easy
reference.
5GHz Dipole
Antenna
2.4GHz Dipole
Antenna
Ethernet Port
Ethernet Port:
Used to connect to power source (see the Power Options in the later section)
and provides 10/100/1000 Mbps network interface for LAN connection.
RF Antenna Ports:
Used to attach 2.4G and 5G antennae for 2x2 MIMO WiFi access coverage
or bridge connection.
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Setup Preparation




Wire stripping tool and crimping tool
Screwdriver (Slot type and Phillips type)
Drill and drill bits
Computer with Web Browser: Google Chrome, Mozilla Firefox, or Microsoft
Internet Explorer 8 (or above)
 Two Cat 5e/6 Ethernet cables
 802.3af-compliant PoE switch
 AltaiCare account (Optional) for cloud AP management and user service
Ethernet Cable Feed-Through
Seal the RJ45 cable Connector with the provided cable gland.
Feed the end of the cable
through the cap nut, sleeve
holder, sealing sleeve as
shown in the picture.
Crimp
the
Ethernet
connector with the crimping
tool.
RJ45 Connector
Connect the cable to the
Ethernet Port.
Sealing Sleeve
Sleeve Holder
Tighten the cap nut.
Cap Nut
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Mounting Options
Option 1: Pole Mount (For 1.5 to 2.5 inches of pole diameter)
Thread the open end of the hose clamp through the two slots of the
mount base.
Determine where the AP is to be placed. Tighten the hose clamp to
secure the base to the pole.
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Option 2: Wall Mount
Determine where the AP is to be placed and use the adhesive label
to mark location of the two mounting holes on the wall surface.
Use an appropriate drill bit to drill two holes, each with 1/3” (8.1mm) in
diameter and 1” (26mm) deep, on the markings.
Remove the label. Drive the anchors into the holes and then the
screws into the anchors.
Align the mounting slots with the screw heads and attach the AP to
the wall in place.
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Power Options and Cable Connection Instructions
You can follow one of the options below for CX200 configuration as
described in the following sections.
Option 1: 802.3at-Compliant PoE switch
1. Connect the CX200 Ethernet port
to
an
802.3af-compliant
PoE
switch with an Ethernet Cable.
2. Connect
computer
to
the
switch.
3. Make sure the Power LED turns into
802.3af – Compliant
PoE Switch
a solid light for AP configuration.
Option 2: PoE Injector (Purchased separately)
1. Connect the PoE injector ports as
described
below
via
Ethernet
Cables.
- PoE Port: Go to CX200
- LAN Port: Go to a computer
2. Connect the PoE Injector to AC
power socket using a power cord.
3. Make sure the Power LED turns into
PoE
LAN
PoE Injector
a solid light for AP configuration.
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
1. Change TCP/IP Setting on Your Computer
For Windows 7/8/10 users,
1. Go to Control Panel, click Network and Sharing Center and then choose
the adapter that you want to connect to CX200 unit. In this example,
adapter “Local Area Connection” is in connection with CX200. Click it and
then click Properties.
2. Under the Networking tab, click Internet Protocol Version 4 (TCP/IPv4) in
the list box “This connection uses the following items”, and then click
Properties.
3. Type in the following IP address and Subnet mask:
 IP address: 192.168.1.2
 Subnet mask: 255.255.255.0
4. Click OK to close the Internet Protocol Version 4 (TCP/IPv4) Properties
dialog box and click OK again to close the Local Area Connection
Properties dialog box.
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
2. Access to Web Interface
1. Open a web browser. Type 192.168.1.222 in the address bar and then hit
Enter.
2. Login page will come up and you are required to enter username and
password. By default, the credentials are:
 Username: admin
 Password: admin
3. Click Login.
10
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
3. Configure AP Mode (2.4G/5G)
Network Scenario
ISP
Modem
Gateway/Router
CX200
(AP Mode)
2.4G + 5G
Coverage
Internet
Modem
Ethernet
Ethernet
Cable
Cable
Cable
Go to Configuration > Wireless > Radio0(2.4G)/Radio1(5G) > General. Below
screenshots show an example for 2.4G radio configuration only. Same
procedures can be applied to 5G radio configuration.
1. Make sure the box of Enable Radio is checked. Select AP mode for the
field of Radio Mode. Then click Submit.
2. Click WLAN and click More… in Detail of WLAN 0 to go to another page
for SSID and security configuration.
11
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
3. Make sure WLAN is enabled by checking the box. Type in SSID to name
the wireless network you want to broadcast and then click Submit.
4. Click the tab WLAN Security. Select WPA2-PSK from the drop down menu
of Authentication Mode and select AES for Cipher Mode. Type in a
password within 8~64 characters or numbers in Pass Phrase and click
Submit.
5. Click Save & Apply at the top right corner to have all changes take effect.
6. Hook up the CX200 as shown in Network
Scenario. The SSID should now be
broadcast from CX200 and can be seen in
the computer for wireless connection.
12
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
4. Connect with Cloud-Based Controller – AltaiCare
Network Scenario:
ISP Modem
CX200_1 (AP)
Local Gateway/
Router
CX200_2 (AP)
1. You can manage your CX200 and set up hotspot service for the
subscribers with AltaiCare, which is a cloud-based system.
2. Go to Configuration > Network > General. Select Switch Mode for Network
Setting and make sure the CX200 can reach Internet and communicate
with AltaiCare by inputting valid IP settings either via DHCP or with Static IP
configuration. Google Public DNS Server can be considered, e.g. 8.8.8.8 or
8.8.4.4 if you are not sure about the ISP DNS’s Server IP.
13
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
3. Click Remote Mgmt and check the box of Enable Remote Management.
Select AltaiCare as Management Type and Cloud as Connection Type.
4. Select Full Management if the device is running in AP Mode. For Station
Mode, Bridge Mode and Repeater Mode, select Monitor Mode instead.
5. Click Submit and then Save & Apply at the top right corner to make all the
changes take effect.
6. Follow AltaiCare Quick Start Guide and register the CX200 in the system for
AP management and user service and admission control.
7. CX200 will appear as online in AltaiCare AP list if the connection is
successful.
14
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Federal Communication Commission Interference Statement (FCC) – USA
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
15
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Professional installation instruction
1. Installation personal
This product is designed for specific application and needs to be installed by a qualified personal
who has RF and related rule knowledge. The general user shall not attempt to install or change
the setting.
2. Installation location
The product shall be installed at a location where the radiating antenna can be kept 20cm from
nearby person in normal operation condition to meet regulatory RF exposure requirement.
3. External antenna
Use only the antennas which have been approved by the applicant. The non-approved
antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead
to the violation of FCC limit and is prohibited.
4. Installation procedure
Please refer to user’s manual for the detail.
5. Warning
Please carefully select the installation position and make sure that the final output power does
not exceed the limit set force in relevant rules. The violation of the rule could lead to serious
federal penalty.
European Conformity (CE) – EU
This is a Class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
16
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Warning
Only use the power adaptor supplied with CX200. Using a different power adaptor might damage the
device.
Disclaimer
All specifications are subject to change without prior notice. Altai Technologies assumes no responsibilities
for any inaccuracies in this document or for any obligation to update information in this document. This
document is provided for information purposes only. Altai Technologies reserves the right to change, modify,
transfer, or otherwise revise this publication without notice.
Copyright © 2018 Altai Technologies Limited
ALL RIGHTS RESERVED.
Altai Technologies Limited
Unit 209, 2/F, Lakeside 2,
10 Science Park West Avenue,
Hong Kong Science Park,
Shatin, New Territories,
Hong Kong
Telephone: +852 3758 6000
Fax: +852 2607 4021
Web: www.altaitechnologies.com
Customer Support Centre:
Email: support@altaitechnologies.com
17
Altai Technologies Ltd. All rights reserved

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 17
Language                        : zh-TW
Tagged PDF                      : Yes
Title                           : CX200 Quick Setup Guide
Author                          : Taylor Wan
Creator                         : Microsoft® Word 2013
Create Date                     : 2018:12:22 15:37:54+08:00
Modify Date                     : 2018:12:22 15:37:54+08:00
Producer                        : Microsoft® Word 2013

EXIF Metadata provided by EXIF.tools