Altec Lansing M402TX Wireless Snooze Remote User Manual part 2

Altec Lansing, LLC Wireless Snooze Remote part 2

UserManual.wiki >

Altec Lansing >

M402TX User Manual >

user manual part 2

Contents

1. user manual part 1
2. user manual part 2

user manual part 2

131 Select FM radio mode.Press the button on your speaker system or enhanced remote until the FM icon appears on the LCD.2 Tune to the station you want to listen to.Use the and buttons on your speaker system or enhanced remote to tune in the desired station. Press and hold these same buttons to ﬁnd the next clear FM station.3 Adjust the volume.UsetheVOLUMEINCREASEandVOLUMEDECREASEbuttonsonthe Altec Lansing speaker system to adjust the system volume. Or, usetheVOLUME+andVOLUME–buttonsontheenhancedremote.NOTE Extend the FM antenna wire fully for best FM reception. Also, do not strip, alter or attach to other antennas.How to Store Preset StationsYour Altec Lansing speaker system’s enhanced remote enables you to program up to 4 FM station presets:1 Tune to the station you wish to store.While in FM radio mode, use the and buttons on your speaker system or enhanced remote to tune to the desired station.2 Store the station.PressandholdtheP1,P2,P3orP4buttonontheenhancedremotefor a few seconds. You can store one FM station in each preset.3 To store other stations, repeat the above steps.How to Recall Preset Stations1 Make sure you are in FM mode.If you’re not in FM mode, press the button on your speaker system or enhanced remote until the FM icon appears on the LCD.2 Press a PRESET button (P1, P2, P3 or P4) on the remote control.The radio will tune to your preset station.3 Adjust the volume.UsetheVOLUMEINCREASEandVOLUMEDECREASEbuttonsonthe Altec Lansing speaker system to adjust the system volume. Or, usetheVOLUME+andVOLUME–buttonsontheenhancedremote.Listening to the FM RadioSNOOZEREMOTEANTENNAFMCLOCKAUXDC

14Listening to a Non-docking iPod or Other Portable Audio DeviceIfyouhaveanon-iPodMP3playerorothernon-dockingportableaudiodevice, you can enjoy it through your Altec Lansing FPO NAME speaker systemaswell.JustconnectitviatheAUXINjack.Here’show:1 Locate a 3.5 mm stereo cable (not included).2 Plug one end of the stereo cable into your device.Your device should have either a headphone or LINE OUT jack for you to plug into.3 Plug the other end of the stereo cable into your speaker system’s AUX IN jack.The AUX IN jack is located on the back of the unit.4 Select AUX IN mode.Press the button on your speaker system or the enhanced remote until the AUX IN icon appears on the speaker system’s LCD.5 Turn on your device and start it playing.6 Adjust the volume.UsetheVOLUMEINCREASEandVOLUMEDECREASEbuttonsonthespeakersystemtoadjustthevolume.Or,usetheVOLUME+andVOLUME–buttonsontheenhancedremote.NOTE You may need to adjust the device volume also. Your device’s volume should be set to approximately ¾ volume.7 When you are ﬁnished listening to your portable audio device, please remember to turn both it and your speaker system off to conserve electricity.SNOOZEREMOTEANTENNAFMCLOCKAUXDC

15Mood LightYour Altec Lansing FPO speaker system is also equipped with a mood light to help you relax and enjoy the music.How to Turn On the Mood LightPress the MOOD button on your Altec Lansing speaker system.How to Adjust the Mood LightYou can enter the Mood Light Setup menu at any time to change colors, adjust modes and set the brightness level.1 Press and hold the MOOD button for 3 seconds.This puts you in the Mood Light Setup menu.2 Choose the color of the ambient light you’d like.Use the and buttons on your speaker system or the enhanced remote to cycle through all the colors the mood light can emit. When the desired color is projected, press the MOOD button again to enter theMoodLightAuto/ManualSelectmenu.3 Select brightness level. (Optional)If in manual mode, press the or button on your speaker system or the enhanced remote to cycle through the available brightness settings. When the desired brightness setting is achieved, press the MOOD button to exit the Mood Light Setup menu. WARNING The mood light isn’t a reading light and doesn’t provide enough light to read by. Please don’t risk damage to your eyesight by trying to read using the mood light.

16Setting the Clock DisplayHow to Set the Clock Time and Date1 Press and hold the CLOCK button for 3 seconds.TheCLOCKbuttonislocatedonthebackofyourAltecLansingspeakersystem.ThisputsyouintheTime/DateSetmode.2 Select either 12-Hour or 24-Hour Clock mode.Press the or button on your speaker system or the enhanced remotetoselecteither12-Houror24-HourClockmode.ThenpresstheCLOCKbuttontosavethissettingandentertheHourSetmode.3 Set the hour.Use the and buttons on your speaker system or the enhanced remotetoadjustthehour.ThenpresstheCLOCKbuttontosavethissetting and enter the Minute Set mode.4 Set the minute.Use the and buttons on your speaker system or the enhanced remotetoadjusttheminute.ThenpresstheCLOCKbuttontosavethissettingandentertheAM/PMSetmode,if12-HourClockmodewaspreviouslyselected.If24-HourClockmodewasselected,pressingtheCLOCKbuttonwillsavetheminutesettingandplacetheunit into Day Set mode.5 Set AM/PM.Press the or button on your speaker system or the enhanced remotetoselectAMorPM.PresstheCLOCKbuttontosavethissetting and enter the Day Set mode.6 Set the day.Press the or button on your speaker system or the enhanced remotetoselectthedayoftheweek.ThenpresstheCLOCKbuttonto save this setting and enter the Month Set mode.

17Setting the Clock Display7 Set the month.Use the and buttons on your speaker system or the enhanced remotetoselectthemonth.PresstheCLOCKbuttontosavethissetting and enter the Date Set mode.8 Set the date.Use the and buttons on your speaker system or the enhanced remotetoselectthedate.PresstheCLOCKbuttontosavethissetting and enter the Year Set mode.9 Set the year.Use the and buttons on your speaker system or the enhanced remotetoselecttheyear.ThenpresstheCLOCKbuttontosavethissetting and enter the Display Option mode.10 Set your display options.Press the or button on your speaker system or the enhanced remote to select one of the following four display options:NOTE Theclockisalwaysdisplayed.Thesizeoftheclockisdependentonthe display option.SongInformation/DateIf song information is available on your iPod or from your radio station, it is displayed. If no song information is available, only the date is displayed.Song Information Only the song information is displayed, if available.Date Only the date is displayed.Clock Only the clock is displayed.

18Setting the AlarmYour Altec Lansing speaker system has two separate alarms.How to Set Alarm 11 Press and hold the ALARM 1 button for 3 seconds.ThisputsyouintheAlarmSetmodeforalarm1.2 Turn Alarm 1 on/offUse the and buttons on your speaker system or the enhanced remotetoselectalarmON.ThenpresstheALARM1 button to savethissettingandentertheAlarmHourSetmode.NOTE If you select alarm OFF, you will exit the menu.3 Adjust the hour.Use the and buttons on your speaker system or the enhanced remotetoadjustthehoursetting.ThenpresstheALARM1 buttontosavethissettingandentertheAM/PMselectionmode.4 Adjust the minute.Use the and buttons on your speaker system or the enhanced remotetoadjusttheminutesetting.ThenpresstheALARM1 button to save this setting and enter the Alarm Source Set mode.5 Select AM or PM.Use the and buttons on your speaker system or the enhanced remotetoselectAMorPM.ThenpresstheALARM1 button to save this setting and enter the Alarm Day Select mode.NOTE Thisoptionisonlyavailableifthe12-hourmodewasselectedwhensetting up the clock.6 Select alarm day setting.Use the and buttons on your speaker system or the enhanced remote to select the alarm day:•ChooseEVERYDAYtohavethealarmgooffeveryday.•ChooseWEEKDAYStohavethealarmgooffMondaythroughFriday.•ChooseWEEKENDStohavethealarmgooffonSaturdayandSunday.•ChooseONETIMEtohavethealarmgooffonlyonceatthenextselected time.ThenpresstheALARM1 button to save this setting and enter the Alarm Source Set mode.

197 Set the alarm source.Press the or button on your speaker system or the enhanced remotetoselectthealarmsource(iPod,FMradioorbuzzer).ThenpresstheALARM1 button to save this setting and enter the SnoozeDurationSetmode.NOTE If you wish to wake up to a speciﬁc song on your iPod, dock your iPod on the speaker system, select the song on your iPod, and then select iPod as your alarm source. The speaker system should remember which song was selected from now on, unless the playlist on your iPod is modiﬁed. If the playlist on your iPod is modiﬁed, either the last song on queue or the ﬁrst song on your song list will play. NOTE Your Altec Lansing speaker system features a backup battery. If a power failure occurs or the AC cord is accidentally disconnected, the display will not remain lit and the alarm will not function. The correct time, however,willbetemporarilymaintained(providedyouhaveinstalleda9-voltbackup battery as described in the Getting Startedsection).NOTE If the iPod or FM radio are playing when the alarm goes off, the alarmwillautomaticallydefaulttothebuzzer,eveniftheiPodorFMradiohave been selected as the alarm source.8 Set snooze duration.Press the or button on your speaker system or the enhanced remotetoselectthesnoozeduration.Thedefaultsnoozedurationis9minutesandcanbeadjustedfrom5minutesto60minutesinincrementsof1minute.ThenpresstheALARM1 button to save this setting and enter the Alarm Volume Set mode.9 Set the alarm volume.Press the or button on your speaker system or the enhanced remotetoselectthealarmvolume(low,mediumorhigh).Thedefaultalarmvolumeismedium.ThenpresstheALARM1 button to save this setting and exit the Alarm Set mode.NOTE When exiting the Alarm Set mode, the Alarm is automatically turned on.Toturnoffthealarm,pressthecorrespondingALARM / button.How to Set Alarm 2Repeat the above steps, substituting “Alarm 2” for “Alarm 1.”How to Use the Snooze FeaturePress the SNOOZE button once to silence the alarm for a period of 5 to 60 minutes (user-deﬁnable).Setting the Alarm

20Maintaining Your Speaker SystemSetting the Sleep TimerPlace your speaker system on a level surface away from sources of direct sunlight or excessive heat.Protect your furniture with a cloth or other protective material when placing your speaker system on a natural wood or lacquered ﬁnish.Clean your speaker system with a soft cloth moistened only with mild soap andwater.Strongercleaningagents,suchasbenzene,thinnerorsimilarmaterials, can damage the surface of the unit.Your Altec Lansing speaker system is equipped with a sleep timer that automaticallyturnsofftheunit5to90minutesafterithasbeenset.How to Set the Sleep Timer1 Turn on the speaker system.2 Press and hold the POWER button for 3 seconds.This puts you in the Sleep Timer mode.3 Choose when you want the speaker system to turn off.Press the or button on your speaker system or the enhanced remote to select how long the unit should play before going on standby(in5-minuteincrements).4 Press the POWER button again.This takes you out of the Sleep Timer mode.

21TroubleshootingSymptom Possible Problem SolutionSpeaker system doesn’t respond(nopower)AC adapter isn’t plugged into a wall outlet or the connector isn’t plugged into the power supply jack on the back of the speaker systemPlug the AC adapter into a wall outlet and plug the connector into the power supply jack on the back of the speaker system.Wall outlet is not functioning Plug another device into the same outlet to conﬁrm the outlet is working.iPod doesn’t dock properlyUsing the wrong iPod insert or no insert Make sure the dock insert is the proper ﬁt for your iPod.iPod didn’t install properly RemoveyouriPodfromthedockandcheckforobstructionontheconnectors in the dock and on your iPod. Then reseat it in the dock.iPod doesn’t respond to the speaker system iPod is not installed properly RemoveyouriPodfromthedockandcheckforobstructionsontheconnectors in the dock and on your iPod. Then reseat it in the dock.Your iPod software is too old Upgrade software on your iPod. For details visit www.apple.com/ipod/download.iPod is locked up Please make sure your iPod is working properly before docking into the unit. Please refer to your iPod manual for details.Using1st-or2nd-generationiPod,iPodshufﬂe or other devicesYour speaker system cannot control those iPods or other devices.

22TroubleshootingSymptom Possible Problem SolutioniPod didn’t chargeiPod is not installed properly RemoveyouriPodfromthedockandcheckforobstructionsontheconnectors in the dock and on your iPod. Then reseat it in the dock.iPod is locked up Please make sure your iPod is working properly before docking into the unit. Please refer to your iPod manual for details.AC adapter isn’t plugged into a wall outlet, or the connector is not plugged into the power supply jack on the back of the speaker systemPlug the AC adapter into a wall outlet and plug the connector into the supply jack on the speaker system.Sound is distortedVolume level is set too high Decrease the volume.Sound source is distorted IftheiPodoriginalsoundsource(MP3)isofpoorquality,distortionandnoiseare easily noticed with high-power speakers. Try a different audio source such as a music CD.Enhanced remote doesn’t workBattery is weak Replacecurrentbatterywithanewbattery.Enhanced remote is not pointed toward the speaker systemPoint the enhanced remote toward the Altec Lansing speaker system and movewithin10feetoftheunit.No sound from the AUX IN device, such as an MP3playerorCDplayerconnected to the AUX IN jackVolume on the device is set too low Increase the volume on the device to approximately ¾ full volume.Source selector is not set to Aux Out Set source selector to Aux Out.

23TroubleshootingSymptom Possible Problem SolutionWirelesssnoozeremotedoesn’t work.Battery is weak Replacecurrentbatterywithanewbattery.Snoozeremotereceiverisnotproperlyplugged into speaker systemSee How to Connect and Pair the Wireless Snooze Remote section.Wirelesssnoozeremoteisnotpaired See How to Connect and Pair the Wireless Snooze Remote section.

24ALTEC LANSING TECHNOLOGIES, INC. ONE-YEAR LIMITED WARRANTY (TWO-YEAR LIMITED WARRANTY IN THE EUROPEAN UNION AND ASIA)What Does the Warranty Cover?Altec Lansing warrants that its products shall be free from defects in materials or workmanship, with the exceptions stated below.What Is the Period of Coverage?For units purchased in the European Union or Asia, this warranty runs for two years from the date of purchase. For units not purchased in Europe or Asia, this warranty runs for one year from the date of purchase. The term of any warranties implied by law shall expire when yourlimitedwarrantyexpires.Somestatesand/orMemberStatesintheEuropeanUniondonot allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.What Does the Warranty Not Cover?This warranty does not cover any defect, malfunction or failure that occurs as a result of: improper installation; misuse or failure to follow the product directions; abuse; or use with improper,unintendedorfaultyequipment.(Forinformationonproperinstallation,operationand use consult the manual supplied with the product. If you require a replacement manual, you may download a manual from www.alteclansing.com.)Also,consequentialandincidental damages are not recoverable under this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.What Will Altec Lansing Do to Correct the Problem?Altec Lansing will, at its option, repair or replace any product that proves to be defective in material or workmanship. If your product is no longer being manufactured, or is out of stock, at its option, Altec Lansing may replace your product with a similar or better Altec Lansing product.How to Get Warranty ServiceTo get a covered product repaired or replaced, you must contact Altec Lansing during thewarrantyperiodbyemail(csupport@alteclansing.com).Youmustincludeinyouremail, your name, address, email address, telephone number, date of purchase and a complete description of the problem you are experiencing. In the United States, you may alternativelycontactAltecLansingbytelephoneat1-800-ALTEC88.Pleasebepreparedtoprovide the same information. If the problem appears to be related to a defect in material orworkmanship,AltecLansingwillprovideyouareturnauthorizationandinstructionsforreturnshipment.Returnshipmentsshallbeatthecustomer’sexpense,andthereturnWarrantymust be accompanied by the original proof of purchase. You should insure the shipment as appropriate because you are responsible for the product until it arrives at Altec Lansing.How Will State Law Affect Your Rights?This warranty gives you speciﬁc legal rights, and you may also have other rights, which vary from state to state. Please note that in the European Union, you as a consumer might have other legal rights under national legislation of European Union Member States governing the sale of Altec Lansing’s goods. Those rights are not affected by this guarantee.The above limited warranties and remedies are sole warranties and remedies available to purchaser, if, and to the extent, valid and enforceable under the applicable law.CUSTOMER SERVICEThe answers to most setup and performance questions can be found in the Troubleshooting section of this guide. You can also consult the FAQs in the customer support section of our Web site at www.alteclansing.com. If you live in North America and still can’t ﬁnd the information you need, please call our customer service team for assistance before returning the speakers to your retailer under their return policy.Tel:800-258-3288Email:csupport@alteclansing.comIf you live outside of North America, please visit our Web site at www.alteclansing.com and select your region to locate your country’s distributor.For the most up-to-date information, be sure to check our Web site at www.alteclansing.com.INTERNATIONAL DISTRIBUTIONInternational customers: For information regarding the distribution of Altec Lansing products in your country, please visit www.alteclansing.com and click on your region.DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENTThis symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city ofﬁce or your household waste disposal service.

Navigation menu