Altis Technology B150 Speaker User Manual Quick start manual of BBY set up

Altis Technology (Hong Kong) Ltd. Speaker Quick start manual of BBY set up

User Manual

Userguide
ProductName:Speaker
ModelName:B150
1. UnscrewtheBluetoothmodulebyturningcounterclockwise(Pic1&2).Take
outthebatteryholderandinsert4AAalkalineorrechargeablebatteries(Pic3&
4).
2. Positionbatteriesaccordingtopolaritymarking(Pic.1),andscrewthe
Bluetoothmodulebyturningclockwise(Pic2).
3. ToturntheFlashlighton,pulltheglobeandpressthe“M”button,theflashlight
willalwaysturnonatthebrightestsettingwiththelanternmode.Holdthe“M”
buttondowncandimorbrighten.Thelightwillflashtwiceatthelowest/
brightestlevel.
4. Toenableflashlightmode,collapsetheglobe.
5. Pressandholdthe“ON/OFF”buttonfor2to3secondstoswitchonthe
Bluetoothmodule.TheBluetoothmodulewillpoweron(Bluetoothname:B150)
VoicereminderaftertheBluetoothbeingactivated:
1.WhentheBluetoothmoduleison,voiceindicatorwillsay“Hello,This
systemisON.Enterpairingmode”.
2.Whenpairingiscompleted,thevoiceindicatorwillsay“Connected”.
3.Whenitisdisconnected,thevoiceindicatorwillsay“Disconnected,Enter
pairingmode”.
4.WhentheBluetoothcannotbeconnectedsuccessfully,thevoiceindicator
willsay“Enterpairingmode”.
5.Pressandholdthe“ON/OFF”buttonagaintoswitchofftheBluetooth
module,thevoiceindicatorwillsay“ByeBye”.
6.Whenthebatteryislow,thevoiceindicatorwillsay“LowBattery”.
IftheBluetoothmoduledidnotpairwithanydevices,thevoiceindicatorwill
say“Enterpairingmode”every3minutesuntilthemoduleispaired.
IftheBluetoothmodulecannotpairwithanydeviceswithin15minutes,the
voiceindicatorwillsay“ByeBye”andswitchofftheunitautomatically.
6.TodisconnecttheBluetoothconnectionbyholdingthe“ON/OFF”buttonfor2
seconds.
7. WhentheFlashlight/Bluetoothatlowbatterylevel,thevoiceindicatorwill
say“LowBattery”toremindtheunitneedstoberecharged.
8. ToremovetheUSBchargercoverandconnectwiththeUSBcabletocharge
theunit.Theunitischargingifthegreen/redlightflashingalternatively.For
example,itwilltakearound7hourstofullyrechargea1300mAhandthe
greenlightisonwhentheunitisbeingfullycharged.
1. Tounscrewtheexistingmodulebyturningcounterclockwiseandreplacethe
“EmergencyPowerBank”unit.
2. ToremovethecoveroftheUSBchargingportandpress“ON/OFF”(Pic.1)
greenlightisonifpoweroutputisinorder(Pic.2).Topress“ON/OFF”
buttonagaintoturnoffthepoweroutput.
3. EmergencyPowerBankcanworkindependently.Greenlightwillflash(Pic.1)
whenchargingthephone.WhentheEmergencyPowerBankatlowbattery
level,green/redlightwillflashalternatively(Pic.2)toreminderusertore
chargetheunit.
4. Theredlightwillon(Pic.1)whentheEmergencyPowerBankisbeing
charged,thegreenlightwillon(Pic.2)whenitisfullycharged.
5. WhentheFlashlightusetogetherwiththeEmergencyPowerBank,thered
lightontheUSBchargingportwillflashtoindicatethelowbatteryleveland
theunitneedtoberecharged.
warningstatement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

Navigation menu