Download: | ![Alvarion Technologies BMAX-OR-25 BreezeMax 4Motion Broadband Wireless System User Manual 4Motion System Manual](/pdf.png) |
Mirror Download [FCC.gov] | ![Alvarion Technologies BMAX-OR-25 BreezeMax 4Motion Broadband Wireless System User Manual 4Motion System Manual](/pdf.png) |
Document ID | 1114031 |
Application ID | Cg3Yf2Gu+eCTl0+gN5l/cQ== |
Document Description | Manual 3 |
Short Term Confidential | No |
Permanent Confidential | No |
Supercede | No |
Document Type | User Manual |
Display Format | Adobe Acrobat PDF - pdf |
Filesize | 78.68kB (983480 bits) |
Date Submitted | 2009-05-21 00:00:00 |
Date Available | 2009-05-21 00:00:00 |
Creation Date | 2009-05-05 09:21:02 |
Producing Software | Acrobat Distiller 8.1.0 (Windows) |
Document Lastmod | 2009-05-05 10:45:30 |
Document Title | 4Motion System Manual |
Document Creator | FrameMaker 8.0 |
Document Author: | Alvarion Ltd. |
Chapter 4 - Operation and Administration Using the CLI
Display
Format
(for each
existing AU
object if
requested
for all AUs)
Command
Modes
4Motion
Managing AUs
SlotNo.
:
ReservedParameter1
:
ReservedParameter2
:
ReservedParameter3
:
ReservedParameter4
:
ReservedParameter5
:
ReservedParameter6
:
ReservedParameter7
:
ReservedParameter8
:
ReservedParameter9
:
Global command mode
482
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.6
Managing ODUs
Managing ODUs
Up to 28 ODU objects can be created and configured, corresponding to up to 28
ODUs that can be installed. Up to four ODU Ports, numbered 1 to 4, can be
created and configured for each ODU. However, for a 1by1 ODU only port number
1 is meaningful. For a 2by1 ODU only ports 1 and 2 are meaningful.
This section include:
“Configuring ODUs”, Section 4.6.1
“Configuring ODU Ports”, Section 4.6.2
4.6.1
Configuring ODUs
To configure an ODU:
Enable the ODU configuration mode for the selected ODU (refer to
Section 4.6.1.1)
You can now execute any of the following tasks:
»
Configure one or more of the parameters tables of the ODU (refer to
Section 4.6.1.2)
»
Restore the default values of parameters in one or more of the parameters
tables of the ODU (refer to Section 4.6.1.3)
Terminate the ODU configuration mode (refer to Section 4.6.1.4)
In addition, you can, at any time, display configuration and status information for
each of the parameters tables of the ODU (refer to Section 4.6.1.6) or delete an
existing ODU object (refer to Section 4.6.1.5).
4.6.1.1
Enabling the ODU Parameters Configuration Mode\Creating
an ODU Object
To configure the parameters of an ODU, first enable the ODU parameters
configuration mode for the specific ODU. Run the following command to enable
the ODU parameters configuration mode for an existing ODU object:
npu (config)# odu-params <(1 to 28 StepSize 1)>
4Motion
483
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing ODUs
To create a new ODU object, the mandatory required-odu-type parameter must be
specified. Run the following command to create a new ODU object and enable the
parameters configuration mode for this ODU:
npu (config)# odu-params <(1 to 28 StepSize 1)> required-odu-type
{oDU23002360000N361by1N0 | oDU24962602000N361by1N0 |
oDU25902690000N361by1N0 | oDU24962602000N382by1N0 |
oDU25902690000N382by1N0 | oDU34003455000N341by1N0 |
oDU34453500000N341by1N0 | oDU35003555000N341by1N0 |
oDU35453600000N341by1N0 | oDU24962602000N384by2N0 |
oDU25902690000N384by2N0 | oDU34003600000N372by1N0 |
oDU36003800000N372by1N0 | oDU34003600000N374by2N0 |
oDU36003800000N374by2N0 | oDU23052360000N361by1Y0 |
oDU24962602000N392by1N0 | oDU25902690000N392by1N0 |
oDU24962602000N394by2N0 | oDU25902690000N394by2N0}
A new ODU object is created with default values for all parameters except to the
mandatory required-odu-type parameter.
IMPORTANT
An error may occur if you provide an invalid value for any of these parameters. Refer the syntax
description for more information about the appropriate values and format for configuring these
parameters.
For example, to create an ODU 1 object and enable the parameters configuration
mode for this ODU, where the required odu type is oDU23002360000N361by1N0,
run the following command:
npu (config)# odu-params 1 required-odu-type oDU23002360000N361by1N0
After enabling the parameters configuration mode for an ODU you can execute
any of the following tasks:
Configure one or more of the parameters tables of the ODU (refer to
Section 4.6.1.2)
Restore the default values of parameters in one or more of the parameters
tables of the ODU (refer to Section 4.6.1.3)
After executing the above tasks, you can terminate the ODU parameters
configuration mode (refer to Section 4.6.1.4) and return to the global
configuration mode.
4Motion
484
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing ODUs
Command
Syntax
npu (config)# odu-params <(1 to 28 StepSize 1)> [required-odu-type
{oDU23002360000N361by1N0 | oDU24962602000N361by1N0 | oDU25902690000N361by1N0 |
oDU24962602000N382by1N0 | oDU25902690000N382by1N0 | oDU34003455000N341by1N0 |
oDU34453500000N341by1N0 | oDU35003555000N341by1N0 | oDU35453600000N341by1N0 |
oDU24962602000N384by2N0 | oDU25902690000N384by2N0 | oDU34003600000N372by1N0 |
oDU36003800000N372by1N0 | oDU34003600000N374by2N0 | oDU36003800000N374by2N0 |
oDU23052360000N361by1Y0 | oDU24962602000N392by1N0 | oDU25902690000N392by1N0 |
oDU24962602000N394by2N0 | oDU25902690000N394by2N0}
Privilege
Level
10
Syntax
Description
4Motion
Parameter
Description
Presence
Default
Value
Possible Values
<(1 to 28
StepSize 1)>
The ODU
number
Mandatory
N/A
1-28
485
System Manual
Chapter 4 - Operation and Administration Using the CLI
required-odu-type
{oDU2300236000
0N361by1N0 |
oDU2496260200
0N361by1N0 |
oDU2590269000
0N361by1N0 |
oDU2496260200
0N382by1N0 |
oDU2590269000
0N382by1N0 |
oDU3400345500
0N341by1N0 |
oDU3445350000
0N341by1N0 |
oDU3500355500
0N341by1N0 |
oDU3545360000
0N341by1N0 |
oDU2496260200
0N384by2N0 |
oDU2590269000
0N384by2N0 |
oDU3400360000
0N372by1N0 |
oDU3600380000
0N372by1N0 |
oDU3400360000
0N374by2N0 |
oDU3600380000
0N374by2N0 |
oDU2305236000
0N361by1Y0 |
oDU2496260200
0N392by1N0 |
oDU2590269000
0N392by1N0 |
oDU2496260200
0N394by2N0 |
oDU2590269000
0N394by2N0}
Command
Modes
The required
ODU type
(see details
below).
Managing ODUs
Mandatory
for a new
ODU object
N/A
oDU23002360000N361by1N0
oDU24962602000N361by1N0
oDU25902690000N361by1N0
oDU24962602000N382by1N0
oDU25902690000N382by1N0
oDU34003455000N341by1N0
oDU34453500000N341by1N0
oDU35003555000N341by1N0
oDU35453600000N341by1N0
oDU24962602000N384by2N0
oDU25902690000N384by2N0
oDU34003600000N372by1N0
oDU36003800000N372by1N0
oDU34003600000N374by2N0
oDU36003800000N374by2N0
oDU23052360000N361by1Y0
oDU24962602000N392by1N0
oDU25902690000N392by1N0
oDU24962602000N394by2N0
oDU25902690000N394by2N0
Global configuration mode
ODU Type = oDUAAAABBBBZZZWPPRbyTCS, where:
AAAA = Lower bound of frequency band in MHz, rounded up to the nearest integer.
4Motion
486
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing ODUs
BBBB = Upper bound of frequency band in MHz, rounded down.
ZZZ = 000 in TDD systems.
W = N in TDD systems.
PP = maximum transmit power in dBm, rounded down.
R = number of receive channels.
T = number of transmit channels.
C = Y if cavity filter is present, N if not.
S = Reserved (0).
The currently available ODUs are:
Table 4-27: Currently Available Single Port ODU Types
ODU Type in CLI
ODU Marketing Nane
Frequency Band (MHz)
Max Tx
Power (dBm)
oDU23002360000N361by1N0
BMAX-AU-ODU-HP-2.3
2300-2360
36
oDU24962602000N361by1N0
BMAX-AU-ODU-HP-2.5A
2496-2602
36
oDU25902690000N361by1N0
BMAX-AU-ODU-HP-2.5B
2590-2690
36
oDU34003455000N341by1N0
BMAX-AU-ODU-HP-TDD-3.4a
3400-3455
34
oDU34453500000N341by1N0
BMAX-AU-ODU-HP-TDD-3.4b
3445-3500
34
oDU35003555000N341by1N0
BMAX-AU-ODU-HP-TDD-3.5a
3500-3555
34
oDU35453600000N341by1N0
BMAX-AU-ODU-HP-TDD-3.5b
3545-3600
34
Tx
Table 4-28: Currently Available 4Rx x 2Tx ODU Types
ODU Type in CLI
ODU Marketing Nane
Frequency Band
(MHz)
Max Tx
Power (dBm)
oDU24962602000N384by2N0
ODU-2496-2602-000N-38-4x2-N-0
2496-2602
38
oDU25902690000N384by2N0
ODU-2590-2690-000N-38-4x2-N-0
2590-2690
38
oDU34003600000N374by2N0
ODU-3400-3600-000N-37-4x2-N-0
3400-3600
37
oDU36003800000N374by2N0
ODU-3600-3800-000N-37-4x2-N-0
3600-3800
37
NOTE
The following examples are for odu-1 parameters configuration mode.
4.6.1.2
Configuring ODU Parameters
After enabling the ODU parameters configuration mode you can configure the
following parameters tables:
General (refer to Section 4.6.1.2.1)
4Motion
487
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing ODUs
Reserved (refer to Section 4.6.1.2.2)
4.6.1.2.1
Configuring General ODU Parameters
The general table enables configuring the main properties of the required ODU.
To configure the general ODU parameters, run the following command:
npu(config-odu-params-1)# odu-general [heater-existence {TRUE | FALSE} ]
[external-cavity-filter-existence {TRUE | FALSE} ] [required-odu-type
{oDU23002360000N361by1N0 | oDU24962602000N361by1N0 |
oDU25902690000N361by1N0 | oDU24962602000N382by1N0 |
oDU25902690000N382by1N0 | oDU34003455000N341by1N0 |
oDU34453500000N341by1N0 | oDU35003555000N341by1N0 |
oDU35453600000N341by1N0 | oDU24962602000N384by2N0 |
oDU25902690000N384by2N0 | oDU34003600000N372by1N0 |
oDU36003800000N372by1N0 | oDU34003600000N374by2N0 |
oDU36003800000N374by2N0 | oDU23052360000N361by1Y0 |
oDU24962602000N392by1N0 | oDU25902690000N392by1N0 |
oDU24962602000N394by2N0 | oDU25902690000N394by2N0} ]
NOTE
You can display configuration information for the ODU general parameters. For details, refer to
Section 4.6.1.6.1.
IMPORTANT
An error may occur if you provide an invalid value for any of these parameters. Refer the syntax
description for more information about the appropriate values and format for configuring these
parameters.
Command
Syntax
4Motion
npu(config-odu-params-1)# odu-general [heater-existence {TRUE |
FALSE} ] [external-cavity-filter-existence {TRUE | FALSE} ]
[required-odu-type {oDU23002360000N361by1N0 |
oDU24962602000N361by1N0 | oDU25902690000N361by1N0 |
oDU24962602000N382by1N0 | oDU25902690000N382by1N0 |
oDU34003455000N341by1N0 | oDU34453500000N341by1N0 |
oDU35003555000N341by1N0 | oDU35453600000N341by1N0 |
oDU24962602000N384by2N0 | oDU25902690000N384by2N0 |
oDU34003600000N372by1N0 | oDU36003800000N372by1N0 |
oDU34003600000N374by2N0 | oDU36003800000N374by2N0 |
oDU23052360000N361by1Y0 | oDU24962602000N392by1N0 |
oDU25902690000N392by1N0 | oDU24962602000N394by2N0 |
oDU25902690000N394by2N0} ]
488
System Manual
Chapter 4 - Operation and Administration Using the CLI
Privilege
Level
Syntax
Description
Managing ODUs
10
Parameter
Description
Presence
Default
Value
Possible Values
[heater-existence
{TRUE | FALSE}]
Informational parameter
indicating whether a
heater for the ODU exists.
Optional
FALSE
TRUE
[external-cavity-filte
r-existence {TRUE
| FALSE}]
Informational parameter
indicating whether an
external cavity filter for the
ODU exists.
Optional
[required-odu-type
{...} ]
The required ODU type.
Optional
FALSE
4.6.1.2.2
TRUE
FALSE
For more details refer to
Section 4.6.1.1
Command
Modes
FALSE
The
previously
configured
valuw
For details refer to
Section 4.6.1.1
odu-params configuration mode
Configuring ODU Reserved Parameters
As the name implies, the reserved parameters table enables configuring up to 9
parameters that are reserved for possible future use. In the current release none
of the reserved parameters is being used.
To configure the ODU reserved parameters, run the following command:
npu(config-odu-params-1)# odu-reserved [reserved-1 ]
[reserved-2 ] [reserved-3 ] [reserved-4
] [reserved-5 ] [reserved-6 ] [reserved-7 ] [reserved-8 ]
[reserved-9 ].
Command
Syntax
4Motion
npu (config-odu-params-1)#
[reserved-2 ]
] [reserved-5
(32)>] [reserved-7 ]
odu-reserved [reserved-1 ]
[reserved-3 ] [reserved-4
] [reserved-6 ] [reserved-8 ]
489
System Manual
Chapter 4 - Operation and Administration Using the CLI
Privilege
Level
Syntax
Description
Command
Modes
4.6.1.3
Managing ODUs
10
Parameter
Description
Presence
Default
Value
Possible
Values
[reserved-N ] (N=1-9)
Reserved parameter number
Optional
null (an
empty
string)
A string of 32
printable
characters.
odu-params configuration mode
Restoring Default Values for ODU Configuration Parameters
After enabling the ODU parameters configuration mode you can restore the
default values for parameters in the following parameters tables:
General (refer to Section 4.6.1.3.1)
Reserved (refer to Section 4.6.1.3.2)
4.6.1.3.1
Restoring the Default Values of General Parameters
To restore one or all of the general parameters to their default value (excluding the
mandatory required-odu-type parameter), run the following command:
npu(config-odu-params-1)# no odu-general [heater-existence]
[external-cavity-filter-existence]
You can restore only one parameter to its default value by specifying only that
parameter. For example, to restore only the heater-existence to the default value
(FALSE), run the following command:
npu(config-odu-params-1)# no odu-general heater-existence
The parameter will be restored to its default value, while the other parameters will
remain unchanged.
To restore all general parameters to their default value, run the following
command:
npu(config-odu-params-1)# no odu-general
4Motion
490
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing ODUs
NOTE
Refer to Section 4.6.1.2.1 for a description and default values of these parameters.
Command
Syntax
npu(config-odu-params-1)# no odu-general [heater-existence]
[external-cavity-filter-existence]
Privilege
Level
10
Command
Modes
odu-params configuration mode
4.6.1.3.2
Restoring the Default Values of ODU Reserved Parameters
To restore the ODU Reserved parameters to their default value, run the following
command:
npu(config-odu-params-1)# no odu-reserved [reserved-1] [reserved-2]
[reserved-3] [reserved-4] [reserved-5] [reserved-6] [reserved-7]
[reserved-8] [reserved-9]
You can restore only selected parameters to their default value by specifying only
those parameter. For example, to restore only the reserved-1 parameter to its
default values, run the following command:
npu(config-odu-params-1)# no odu-reserved reserved-1
This parameter will be restored to the default value, while the other parameters
will remain unchanged.
To restore all parameters to their default value, run the following command:
npu(config-odu-params-1)# no odu-reserved
NOTE
Refer to Section 4.6.1.2.2 for a description and default values of these parameters.
Command
Syntax
npu(config-odu-params-1)# no odu-reserved [reserved-1]
[reserved-2] [reserved-3] [reserved-4] [reserved-5] [reserved-6]
[reserved-7] [reserved-8] [reserved-9]
4Motion
491
System Manual
Chapter 4 - Operation and Administration Using the CLI
Privilege
Level
10
Command
Modes
odu-params configuration mode
4.6.1.4
Managing ODUs
Terminating the ODU Parameters Configuration Mode
Run the following command to terminate the ODU Parameters configuration
mode:
npu(config-odu-params-1)# exit
Command
Syntax
npu(config-odu-params-1)# exit
Privilege
Level
10
Command
Modes
odu-params configuration mode
4.6.1.5
Deleting an ODU Object
Run the following command to delete an ODU object:
npu(config)# no odu-params <(1 to 28 StepSize 1)>
IMPORTANT
An associated ODU (specified in a Sector Association) cannot be deleted.
Command
Syntax
npu(config)# no odu-params <(1 to 28 StepSize 1)>
Privilege
Level
10
4Motion
492
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Command
Modes
4.6.1.6
Managing ODUs
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 28 StepSize 1)>
The ODU number
Mandatory
N/A
1-28
Global configuration mode
Displaying Configuration and Status Information for ODU
Parameters
You can display the current configuration and (where applicable) additional status
information for the following parameters tables:
General (refer to Section 4.6.1.6.1)
Reserved (refer to Section 4.6.1.6.2)
4.6.1.6.1
Displaying Configuration and Status Information for ODU General
Parameters
To display configuration and status information for the general parameters of a
specific or all ODU objects, run the following command:
npu# show odu-general [odu-no <(1 to 28 StepSize 1)>]
Specify the ODU number (1-28) if you want to display configuration and status
information for a particular ODU. Do not specify a value for this parameter if you
want to view configuration and status information for all existing ODU objects.
Command
Syntax
npu# show odu-general [odu-no <(1 to 28 StepSize 1)> ]
Privilege
Level
4Motion
493
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Display
Format
(for each
existing
ODU object
if requested
for all
ODUs)
Command
Modes
Managing ODUs
Parameter
Description
Presence
Default
Value
Possible
Values
[odu-no <(1 to 28
StepSize 1)> ]
The number of the ODU
Optional
N/A
1-28
Specify a value for this
parameter if you want to
display the general
parameters of a specific
ODU. Do not specify a value
for this parameter if you want
to display the general
parameters of all ODUs.
ODUNo.
:
HeaterExistence
: or (0) if object does not exist
ExternalCavityFilterExistence
: or (0) if object does not exist
RequiredODUType
: or (0) if object does not exist
InstalledODUType
: or (0) if ODU is not installed
SerialNumber
: or null if ODU is not installed
Global command mode
In addition to the configurable parameters, the following status parameters are
also displayed:
4Motion
494
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing ODUs
Parameter
Description
Possible Values
InstalledODUType
The installed ODU Type.
oDU23002360000N361by1N0 (1)
oDU24962602000N361by1N0 (2)
oDU25902690000N361by1N0 (3)
oDU24962602000N382by1N0 (4)
oDU25902690000N382by1N0 (5)
oDU34003455000N341by1N0 (6)
oDU34453500000N341by1N0 (7)
oDU35003555000N341by1N0 (8)
oDU35453600000N341by1N0 (9)
oDU24962602000N384by2N0 (10)
oDU25902690000N384by2N0 (11)
oDU34003600000N372by1N0 (12)
oDU36003800000N372by1N0 (13)
oDU34003600000N374by2N0 (14)
oDU36003800000N374by2N0 (15)
oDU23052360000N361by1Y0 (16)
oDU24962602000N392by1N0 (17)
oDU25902690000N392by1N0 (18)
oDU24962602000N394by2N0 (19)
oDU25902690000N394by2N0 (20)
odunotDetected (97)
odutypeUnknown (98)
odunotAssociated to sector (0)
SerialNumber
4Motion
The ODU serial number
495
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.6.1.6.2
Managing ODUs
Displaying Configuration Information for ODU Reserved Parameters
To display configuration information for the reserved parameters of a specific or
all ODU objects, run the following command:
npu# show odu-reserved [odu-no <(1 to 28 StepSize 1)>]
Specify the ODU number (1-28) if you want to display configuration for a
particular ODU. Do not specify a value for this parameter if you want to view
configuration for all existing ODU objects.
Command
Syntax
npu# show odu-reserved [odu-no <(1 to 28 StepSize 1)> ]
Privilege
Level
Syntax
Description
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
[odu-no <(1 to 28
StepSize 1)> ]
The number of the ODU
Optional
N/A
1-28
Specify a value for this
parameter if you want to
display the reserved
parameters of a specific
ODU. Do not specify a value
for this parameter if you want
to display the reserved
parameters of all ODUs.
496
System Manual
Chapter 4 - Operation and Administration Using the CLI
Display
Format
(for each
existing
ODU object
if requested
for all
ODUs)
Command
Modes
4.6.2
Managing ODUs
ODUNo.
:
ReservedParameter1
:
ReservedParameter2
:
ReservedParameter3
:
ReservedParameter4
:
ReservedParameter5
:
ReservedParameter6
:
ReservedParameter7
:
ReservedParameter8
:
ReservedParameter9
:
Global command mode
Configuring ODU Ports
Up to four ODU Ports, numbered 1 to 4, can be created and configured for each
ODU. However, for a 1by1 ODU only port number 1 is meaningful. For a 2by1
ODU only ports 1 and 2 are meaningful.
To configure an ODU Port:
Enable the ODU Port configuration mode for the selected ODU Port (refer to
Section 4.6.2.1)
You can now execute any of the following tasks:
»
Configure one or more of the ODU Port parameters (refer to
Section 4.6.2.2)
»
Restore the default value of the txpower-onoff parameter (refer to
Section 4.6.2.3)
Terminate the ODU Port configuration mode (refer to Section 4.6.2.4)
In addition, you can, at any time, display configuration and status information for
each or all of the ODU Ports (refer to Section 4.6.2.6) or delete an existing ODU
Port (refer to Section 4.6.2.5).
4Motion
497
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.6.2.1
Managing ODUs
Enabling the ODU Port Configuration Mode\Creating an
ODU Port
To configure the parameters of an ODU Port, first enable the ODU Port
configuration mode for the specific ODU Port. Run the following command to
enable the ODU Port configuration mode for an existing ODU Port:
npu (config)# odu-port <(1 to 28 StepSize 1)> <(1 to 4 StepSize 1)>
To create a new ODU Port, the mandatory txpower parameter must be specified.
Run the following command to create a new ODU Port and enable the
configuration mode for this ODU Port:
npu (config)# odu-port <(1 to 28 StepSize 1)> <(1 to 4 StepSize 1)> txpower
<(0 to 46 StepSize 0.1)>
A new ODU Port is created with default values for the txpower-onoff parameter.
For example, to create Port 1 in ODU 1 with a configured Tx Power of 34 dBm, and
enable the parameters configuration mode for this ODU Port run the following
command:
npu (config)# odu-port 1 1 txpower 34
After enabling the configuration mode for an ODU Port you can execute any of the
following tasks:
Configure one or more of the parameters of the ODU Port (refer to
Section 4.6.2.2)
Restore the default value of the txpower-onoff parameter (refer to
Section 4.6.2.3)
After executing the above tasks, you can terminate the ODU Port configuration
mode (refer to Section 4.6.2.4) and return to the global configuration mode.
Command
Syntax
npu (config)# odu-port <(1 to 28 StepSize 1)> <(1 to 4 StepSize 1)> [txpower <(0 to 46 StepSize
0.1)>]
Privilege
Level
10
4Motion
498
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Managing ODUs
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 28 StepSize 1)>
The ODU number
Mandatory
N/A
1-28
<(1 to 4 StepSize 1)>
The Port number.
Mandatory
N/A
1-4
[txpower <(0 to 46
StepSize 0.1)>]
The required tx power at the
specified ODU Port, in dBm.
Mandatory
for a new
ODU Port
N/A
0 to 46 in
increment
s of 0.1
The actually available range
depends on ODU Type: The
upper limit is set by the
Maximum Tx Power supported
by the ODU (see “Currently
Available Single Port
ODU Types” on
page 487). The control range
for all ODUs is 10dBm, except
to the following ODUs whose
control range is 6dBm:
oDU23002360000N361by1N0,
oDU24962602000N361by1N0,
oDU25902690000N361by1N0,
oDU23052360000N361by1Y0
Command
Modes
Global configuration mode
NOTE
The following examples are for odu-1, port-1 configuration mode.
4.6.2.2
Configuring ODU Port Parameters
After enabling the ODU Port configuration mode you can configure the transmit
power parameters of the port.
To configure the ODU Port parameters, run the following command:
npu(config-odu-port-1-1)# params [txpower <(0 to 46 StepSize 0.1)> ]
[txpower-onoff {on | off} ]
NOTE
You can display configuration information for the ODU Port parameters. For details, refer to
Section 4.6.2.6.
4Motion
499
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing ODUs
IMPORTANT
An error may occur if you provide an invalid value for any of these parameters. Refer the syntax
description for more information about the appropriate values and format for configuring these
parameters.
Command
Syntax
npu(config-odu-port-1-1)# params [txpower <(0 to 46 StepSize
0.1)>] [txpower-onoff {on | off} ]
Privilege
Level
10
Syntax
Description
Parameter
Description
Presence
Default
Value
Possible
Values
[txpower <(0 to 46
StepSize 0.1)>]
The transmit power at the
ODU Port, in dBm.
Optional
As
configured
previouslu
0 to 46 in
increments of 0.1
on
on
[txpower-onoff {on
| off} ]
Enables or disables
transmissions on this port.
Optional
Actual range
depends on ODU
type.
off
Command
Modes
odu-port configuration mode
IMPORTANT
An error may occur if you provide an invalid value for any of these parameters. Refer the syntax
description for more information about the appropriate values and format for configuring these
parameters.
4.6.2.3
Restoring Default Values for ODU Port Parameters
After enabling the ODU Port configuration mode you can restore the default
values for the txpower-onoff parameter:
To restore the default values for the txpower-onoff parameter, run the following
command:
npu(config-odu-port-1-1)# no params
4Motion
500
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing ODUs
The txpower-onoff parameter will be restored to its default value (on), while the
mandatory txpower parameter will remain unchanged.
Command
Syntax
npu(config-odu-port-1-1)# no params
Privilege
Level
10
Command
Modes
odu-port configuration mode
4.6.2.4
Terminating the ODU Port Configuration Mode
Run the following command to terminate the ODU Port configuration mode:
npu(config-odu-port-1-1)# exit
Command
Syntax
npu(config-odu-port-1-1)# exit
Privilege
Level
10
Command
Modes
odu-port configuration mode
4.6.2.5
Deleting an ODU Port
Run the following command to delete an ODU Port:
npu(config)# no odu-port <(1 to 28 StepSize 1)> <(1 to 4 StepSize 1)>
IMPORTANT
An associated ODU Port (specified in a Sector Association) cannot be deleted.
Command
Syntax
4Motion
npu(config)# no odu-params <(1 to 28 StepSize 1)> <(1 to 4 StepSize 1)>
501
System Manual
Chapter 4 - Operation and Administration Using the CLI
Privilege
Level
Syntax
Description
Command
Modes
4.6.2.6
Managing ODUs
10
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 28 StepSize 1)>
The ODU number
Mandatory
N/A
1-28
<(1 to 4 StepSize 1)>
The Port number
Mandatory
N/A
1-4
Global configuration mode
Displaying Configuration and Status Information for ODU
Ports
To display configuration and status information of a specific or all ODU Ports, run
the following command:
npu# show odu-port [odu-no <(1 to 28 StepSize 1)> port-no <(1 to 4 StepSize 1)>]
Specify the ODU number (1-28) and Port number (1-4) if you want to display
configuration and status information for a particular ODU Port. Do not specify
values for these parameters if you want to view configuration and status
information for all existing ODU Ports.
Command
Syntax
npu# show odu-port [odu-no <(1 to 28 StepSize 1)> port-no <(1 to 4 StepSize 1)> ]
Privilege
Level
4Motion
502
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Display
Format
(for each
existing
ODU Port if
requested
for all ODU
Ports)
Command
Modes
4Motion
Managing ODUs
Parameter
Description
Presence
Default
Value
Possible
Values
[odu-no <(1 to 28
StepSize 1)> ]
The number of the ODU
Optional
N/A
1-28
[port-no <(1 to 4
StepSize 1)> ]
The number of the Port
Optional
N/A
1-4
Specify a value for this
parameter if you want to
display the parameters of a
specific ODU Port. Do not
specify a value for this
parameter if you want to
display the general
parameters of all ODU Ports.
Specify a value for this
parameter if you want to
display the parameters of a
specific ODU Port. Do not
specify a value for this
parameter if you want to
display the general
parameters of all ODU Portss.
ODUNo.
:
ODUPortNo
:
TxPower(dBm)
:
TxEnable
:
HWVersion
:
HWRevision
:
HPACard
:
HPAHWVersion
:
HC08SWVersion
:
CPLDSWVersion
:
SerialNumber
:
txpower-status
:
Global command mode
503
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing ODUs
In addition to the configurable parameters, the following status parameters are
also displayed:
Parameter
Description
Possible Values
HWVersion
HW version no. of ODU basic card connected to
this port
HWRevision
HW revision no. of ODU basic card connected to
this port
HPACard
Indicates whether the port is connected to an
HPA card
installed (1)
notInstalled (0)
4Motion
HPAHWVersion
HW version no. of HPA connected to this port
(relevant only if HPACard is installed)
HC08SWVersion
SW version of HC08 controlling card connected
to this port
CPLDSWVersion
SW version of CPLD controlling card connected
to this port
SerialNumber
Serial number of ODU basic card connected to
this port
txpower-status
The operation status of the port
504
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.7
Managing Antennas
Managing Antennas
Up to 28 Antenna objects, identified by the Antenna number (1-28), can be
created and configured.
To configure an Antenna:
Enable the Antenna configuration mode for the selected Antenna (refer to
Section 4.7.1)
You can now execute any of the following tasks:
»
Configure one or more of the Antenna parameters (Section 4.7.2)
»
Restore the default value of some or all of the Antenna parameters (refer to
Section 4.7.3)
Terminate the Antenna configuration mode (refer to Section 4.7.4)
In addition, you can, at any time, display configuration information for one or all
of the Antennas (refer to Section 4.7.6) or delete an existing Antenna (refer to
Section 4.7.5).
4.7.1
Enabling the Antenna Configuration
Mode\Creating an Antenna
To configure the parameters of an Antenna, first enable the Antenna configuration
mode for the specific Antenna. Run the following command to enable the Antenna
configuration mode for an existing Antenna:
npu (config)# antenna <(1 to 28 StepSize 1)>
To create a new Antenna, the mandatory heading parameter must be specified.
Run the following command to create a new Antenna and enable the configuration
mode for this Antenna:
npu (config)# antenna <(1 to 28 StepSize 1)> heading <(0 to 359 StepSize 1)>
A new Antenna is created with default values for all other parameters.
4Motion
505
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing Antennas
IMPORTANT
An error may occur if you provide an invalid value for any of these parameters. Refer the syntax
description for more information about the appropriate values and format for configuring these
parameters.
For example, to create Antenna 1 with a configured heading of 90 degrees and
enable the parameters configuration mode for this Antenna, run the following
command:
npu (config)# antenna 1 heading 90
CAUTION
When an antenna is associated to a sector, the antenna heading must be the same as the sector
heading for every antenna associated to the sector.
After enabling the configuration mode for an Antenna you can execute any of the
following tasks:
Configure one or more of the parameters of the Antenna (refer to Section 4.7.2)
Restore the default value of the non-mandatory parameters parameter (refer to
Section 4.7.3)
After executing the above tasks, you can terminate the Antenna configuration
mode (refer to Section 4.7.4) and return to the global configuration mode.
Command
Syntax
npu (config)# antenna <(1 to 28 StepSize 1)> [heading <(0 to 359 StepSize 1)>]
Privilege
Level
10
Syntax
Description
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 28 StepSize 1)>
The ODU number
Mandatory
N/A
1-28
506
System Manual
Chapter 4 - Operation and Administration Using the CLI
[heading <(0 to 359
StepSize 1)>]
Command
Modes
Managing Antennas
Indicates the azimuth angle
(in degrees) between the
center of the horizontal
antenna beamwidth and the
true north; counting
clockwise.
Mandatory
for a new
Antenna
N/A
0 to 359
Global configuration mode
NOTE
The following examples are for antenna-1 configuration mode.
4.7.2
Configuring Antenna Parameters
After enabling the Antenna configuration mode you can configure the Antenna
parameters.
To configure the Antenna parameters, run the following command:
npu(config-antenna-1)# params [antenna-type ] [no-of-ports <(1 to 8
StepSize 1)>] [gain <(0 to 60 StepSize 0.1)>] [mechanical-downtilt <(-90 to 90
StepSize 0.1)>] [electrical-downtilt <(-90 to 90 StepSize 0.2)>]
[electrical-azimuth-adjustment <(-90 to 90 StepSize 0.3)>] [longitude ]
[latitude ] [tower-height <(0 to 500 StepSize 1)>] [altitude <(-500 to
10000 StepSize 1)>] [heading <(0 to 359 StepSize 1)>] [beamwidth <(0 to 359
StepSize 1)>] [cable-loss <(0 to 20 StepSize 0.1)>]
Command
Syntax
npu(config-antenna-1)# params [antenna-type ]
[no-of-ports <(1 to 8 StepSize 1)> ] [gain <(0 to 60 StepSize
0.1)> ] [mechanical-downtilt <(-90 to 90 StepSize 0.1)> ]
[electrical-downtil <(-90 to 90 StepSize 0.2)> ]
[electrical-azimuth-adjustment <(-90 to 90 StepSize 0.3)> ]
[longitude ] [latitude ] [tower-height <(0
to 500 StepSize 1)> ] [altitude <(-500 to 10000 StepSize 1)> ]
[heading <(0 to 359 StepSize 1)> ] [beamwidth <(0 to 359 StepSize
1)> ] [cable-loss <(0 to 20 StepSize 0.1)> ]
Privilege
Level
10
4Motion
507
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
4Motion
Managing Antennas
Parameter
Description
Presence
Default
Value
Possible
Values
[antenna-type
]
Antenna type to be populated
manually for inventory
information only
Optional
N/A
String (up to 32
printable
characters)
[no-of-ports <(1 to
8 StepSize 1)> ]
The number of antenna ports
Optional
1-8
[gain <(0 to 60
StepSize 0.1)> ]
Antenna Gain (in dB)
Optional
17
0-60 in steps of
0.1
[mechanical-downt
ilt <(-90 to 90
StepSize 0.1)> ]
Downwards mechanical tilt of
the antenna (in degrees) as
opposed to the electrical tilt
already integrated in the
antenna (and thus taken as
reference; instead of the
horizontal plane)
Optional
-90.0 to 90.0
in steps of 0.1
[electrical-downtil
<(-90 to 90
StepSize 0.1)> ]
Downwards electrical tilt of
the antenna, in degrees
Optional
-90.0 to 90.0
in steps of 0.1
[electrical-azimuthadjustment <(-90
to 90 StepSize
0.1)> ]
Electrical azimuth adjustment
of the antenna, in degrees (in
a clockwise direction)
Optional
-90.0 to 90.0
in steps of 0.1
[longitude
]
The longitude of the antenna.
Optional
000.000;
String
[latitude
The latitude of the antenna.
Optional
000.000;
String
[tower-height <(0
to 500 StepSize
1)> ]
Defines the height of the
antenna above the ground in
meters.
Optional
0-500
The recommended format is
lll.mmm.a where lll.mmm is
the longitude in degrees (lll between 000 and 180, mmm between 000 and 999), a is E
(East) or W (West).
The recommended format is
lll.mmm.a where lll.mmm is
the longitude in degrees (lll between 000 and 90, mmm between 000 and 999), a is N
(North) or S (South).
508
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Modes
Managing Antennas
[altitude <(-500 to
10000 StepSize
1)> ]
Absolute altitude of the
sector (above sea level) in
meters.
Optional
-500 to 10000
[heading <(0 to
359 StepSize 1)> ]
Indicates the azimuth angle
(in degrees) between the
center of the horizontal
antenna beamwidth and the
true north; counting
clockwise.
Optional
0-359
[beamwidth <(0 to
359 StepSize 1)> ]
Beamwidth of the antenna in
degrees
Optional
60
0-359
[cable-loss <(0 to
20 StepSize 0.1)> ]
The attenuation (in dB) of the
cable between the ODU port
and antenna port (informative
only)
Optional
0.5
0-20 in steps of
0.1
antenna configuration mode
NOTE
You can display configuration information for the Antenna parameters. For details, refer to
Section 4.7.6.
IMPORTANT
An error may occur if you provide an invalid value for any of these parameters. Refer the syntax
description for more information about the appropriate values and format for configuring these
parameters.
4.7.3
Restoring Default Values for Antenna
Parameters
After enabling the Antenna configuration mode you can restore the default values
for some or all of the parameters (excluding the mandatory heading parameter).
To restore one or several Antenna parameters do their default value, run the
following command:
npu(config-antenna-1)# no params [antenna-type] [no-of-ports]
[gain] [mechanical-downtilt] [electrical-downtil]
[electrical-azimuth-adjustment] [longitude] [latitude]
[tower-height] [altitude] [beamwidth] [cable-loss]
4Motion
509
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing Antennas
You can restore one or several parameters to the default value(s) by specifying
only those parameter. For example, to restore only the mechanical-downtilt and
electrical-downtilt to their default values, run the following command:
npu(config-antenna-1)# no params mechanical-downtilt
electrical-downtil
The mechanical-downtilt and electrical-downtilt will be restored to their default
values, while all other parameters will remain unchanged.
To restore all parameters to their default value, run the following command:
npu(config-antenna-1)# no params
NOTE
Refer to Section 4.7.2 for a description and default values of these parameters.
Command
Syntax
npu(config-antenna-1)# no params [antenna-type] [no-of-ports]
[gain] [mechanical-downtilt] [electrical-downtil]
[electrical-azimuth-adjustment] [longitude] [latitude]
[tower-height] [altitude] [beamwidth] [cable-loss]
Privilege
Level
10
Command
Modes
antenna configuration mode
4.7.4
Terminating the Antenna Configuration Mode
Run the following command to terminate the Antenna configuration mode:
npu(config-antenna-1)# exit
Command
Syntax
npu(config-antenna-1)# exit
Privilege
Level
10
4Motion
510
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Modes
4.7.5
Managing Antennas
antenna configuration mode
Deleting an Antenna
Run the following command to delete an Antenna:
npu(config)# no antenna <(1 to 28 StepSize 1)>
IMPORTANT
An associated Antenna (specified in a Sector Association) cannot be deleted.
Command
Syntax
npu(config)# no antenna <(1 to 28 StepSize 1)>
Privilege
Level
10
Syntax
Description
Command
Modes
4.7.6
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 28 StepSize 1)>
The Antenna number
Mandatory
N/A
1-28
Global configuration mode
Displaying Configuration Information for
Antennas
To display configuration information of a specific or all Antennas, run the
following command:
npu# show antenna [antenna-no <(1 to 28 StepSize 1)>]
Specify the Antenna number (1-28) if you want to display configuration
information for a particular Antenna. Do not specify values for this parameter if
you want to view configuration information for all existing Antennas.
4Motion
511
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing Antennas
Command
Syntax
npu# show antenna [antenna-no <(1 to 28 StepSize 1)>]
Privilege
Level
Syntax
Description
Display
Format
(for each
existing
Antenna if
requested
for all
Antennas)
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
[antenna-no <(1 to
28 StepSize 1)> ]
The number of the Antenna
Optional
N/A
1-28
Specify a value for this
parameter if you want to
display the parameters of a
specific Antenna. Do not
specify a value for this
parameter if you want to
display the parameters of all
Antennas.
AntennaNo.
:
AntennaType
:
No.ofPorts
:
Gain(dB)
:
MechanicalDownTilt(degrees)
:
ElectricalDownTilt(degrees)
:
ElectricalAzymuthAdjustment(degrees)
:
Longtitude
:
Latitude
:
TowerHeight(meters)
:
Altitude(meters)
:
AntennaHeading(degrees)
:
AntennaBeamWidth(degrees)
:
CableLoss(dB)
:
512
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Modes
4Motion
Managing Antennas
Global command mode
513
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8
Managing BSs
Managing BSs
Up to 28 different BSs can be defined.
The full configuration of each BS includes multiple components (tables). Many of
these tables include one or more mandatory parameters (parameters with no
default value). The creation of a new BS is not completed until all mandatory
parameters have been configured.
For each table that has only optional (non-mandatory) parameters, at least one
parameter must be configured explicitly (even if not changed from the default
value) when creating a new BS.
Due to the complicated structure of the BS object and the high number of
mandatory parameters in different tables, a special apply command must be
executed for properly completing the configuration of certain tables. The apply
command must be executed before exiting the applicable configuration mode.
Failure to execute the apply command will result in loss of the newly configured
parameters. Wherever required, the need to use the apply command will be
indicated in the manual.
The following table lists the tasks for configuring a BS, indicating the applicable
mandatory parameters and the need to execute the apply command where
applicable. When configuring a new BS, verify that all mandatory parameters have
been configured (otherwise a trial to associate the BS to a Sector will fail):
Table 4-29: Tasks for Configuring a BS
Task
Mandatory Parameters
“Enabling the BS Configuration
Mode\Creating a BS Object” on
page 518
bs id
“Managing BS General Parameters” on
page 520
“Managing BS Services” on page 523
4Motion
apply required
No
No
service name (type)
514
Yes
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Table 4-29: Tasks for Configuring a BS
Task
Mandatory Parameters
apply required
“Managing Service Mapping Rules” on
page 529
service mapping rule index
Yes
srvc (service-name)
order
r1 profile parameters:
datadelivery-type
priority
mir
cir
jitter
latency
sdu-size
grant-interval
“Managing Power Control Levels and
Policies” on page 548
“Managing BS Feedback Allocation
Parameters” on page 580
Yes
max-cqi
No
“Managing Neighbor Advertisement
Parameters” on page 584
No
“Managing Triggers Parameters” on
page 587
No
“Managing Trigger Setup Parameters” on
page 591
No
“Managing Scan Negotiation
Parameters” on page 595
No
“Managing Handover Negotiation at SBS
Parameters” on page 599
No
4Motion
515
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Table 4-29: Tasks for Configuring a BS
Task
Mandatory Parameters
“Managing Neighbor BSs” on page 606
General Parameters:
apply required
Yes
eirp
bw
feedbackzone-permbase
ucd-configchangecount
dcd-configchangecount
frequency
restartcount
preamble-idx
“Managing UCD Parameters” on
page 629
No
“Managing DCD Parameters” on
page 633
No
“Managing the RF Frequency Parameter”
on page 637
frequency
No
“Managing the Baseband Bandwidth
Parameter” on page 640
bandwidth
No
4Motion
516
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Table 4-29: Tasks for Configuring a BS
Task
Mandatory Parameters
“Managing Airframe Structure
Parameters” on page 642
General Parameters:
apply required
Yes
cell-id
segment
frame-offset
ul-dl-allocation
Map Zone Parameters:
majorgrps
Uplink Feedback Zone Parameters:
permbase
Downlink Data Zone:
subchannels
permbase
Uplink Data Zone:
subchannels
“Managing Rate Adaptation Parameters”
on page 683
“Managing BS Bearer Interface
Parameters” on page 692
No
ip-address
No
ip-subnetmask
dflt-gw
“Managing Authentication Relay
Parameters” on page 695
dflt-auth-ip-address
“Managing Handover Control
Parameters” on page 700
“Managing Bearer Traffic QoS Marking
Rules” on page 704
No
enable-srvcflow-mediaflowtype
Yes
srvcflow-mediaflowtype (if
enable-srvcflow-mediaflowtype is set to
True)
“Managing Control Traffic QoS Marking
Rules” on page 712
4Motion
No
Yes
517
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Table 4-29: Tasks for Configuring a BS
Task
Mandatory Parameters
“Managing BS Management Alarm
Thresholds Parameters” on page 721
“Managing ID-IP Mapping Parameters”
on page 724
apply required
No
nw-node-id (Next Hop BS ID)
No
nw-node-ip
“Managing Ranging Parameters” on
page 728
Yes
“Managing Alarm Threshold Parameters”
on page 750
No
“Managing BS Reserved Parameters” on
page 756
No
“Managing the BS Keep-Alive
Functionality” on page 760
No
4.8.1
Enabling the BS Configuration Mode\Creating
a BS Object
To configure the parameters of a BU, first enable the BS configuration mode for
the specific BS. Run the following command to enable the BS configuration mode.
You can also use this command to create a new BS object. Note that for a new
object this command only defines the BS ID, and that the BS is not fully created
until completing configuration of all mandatory parameters.
The BS ID is the unique identifier of the BS in the access network. The BS ID used
in the system is in the format A.B.C where A, B, C are from 0 to 255. The BS ID
used in the CLI is an integer that is calculated by the formula A*65536+B*256+C.
For example, a BS ID of 1.2.5 is translated to 1*65536+2*256+5=66053.
npu(config)# bs <(1 to 16777215 StepSize 1)>
For example, to configure BS 66053, run the following command:
npu (config)# bs 66053
IMPORTANT
An error occurs if you specify BS ID that is not in the range, 1-16777215.
If you use this command to create a new BS, the configuration mode for this BS is
automatically enabled, after which you can execute any of the following tasks:
Configure one or more of the parameters tables of the BS
4Motion
518
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Restore the default values for the non-mandatory parameters of one or more of
the parameters tables of the BS
After executing the above tasks, you can terminate the BS configuration mode
(refer to Section 4.5.4) and return to the global configuration mode. From the
global configuration mode you can delete an existing BS (refer to). You can display
configuration information for selected tables from the global command mode.
Command
Syntax
npu(config)# bs <(1 to 16777215 StepSize 1)>
Privilege
Level
10
Syntax
Description
Command
Modes
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The unique ID (BSIDLSB) of
the BS. Must be unique in the
radio access network. A
number in the range from 1 to
16,777,215 (a 24-bit value
that can be represented as
A.B.C where A, B, C are from
0 to 255).
Mandatory
N/A
1 to 16777215
Global configuration mode
NOTE
The following examples are for bs configuration mode for bs-66053 .
4.8.2
Deleting a BS
Run the following command to delete a BS:
npu(config)# no bs <(1 to 16777215 StepSize 1)>
IMPORTANT
An associated bs (specified in an associated sector) cannot be deleted.
4Motion
519
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Command
Syntax
npu(config)# no bs <(1 to 16777215 StepSize 1)>
Privilege
Level
10
Syntax
Description
Command
Modes
4.8.3
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The unique ID (BSIDLSB) of
the BS.
Mandatory
N/A
1 to
16777215
Global configuration mode
Managing BS General Parameters
The general parameters of a BS include the Operator ID and the BS Name.
After enabling the BS configuration mode, you can execute the following tasks:
Configure one or more of the general parameters (refer to Section 4.8.3.1).
Restore the default values of one or all of the general parameters (refer to
Section 4.8.3.2).
You can display configuration information for the general parameters of a selected
or all existing BSs (refer to Section 4.8.3.3).
4.8.3.1
Configuring BS General Parameters
To configure the BS General Parameters:
From the BS configuration mode, run the following command:
npu(config-bs-66053)# general [operator-id <(1 to 16777215 StepSize 1)>]
[bs-name ]
4Motion
520
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
IMPORTANT
When creating a new BS, at least one of the BS General parameters must be configured explicitly
(even if configured to the default value).
Command
Syntax
npu(config-bs-66053)# general [operator-id <(1 to 16777215
StepSize 1)> ] [bs-name ]
Privilege
Level
10
Syntax
Description
Command
Modes
4.8.3.2
Parameter
Description
Presence
Default
Value
Possible
Values
[operator-id <(1 to
16777215 StepSize 1)>]
A unique operator
identifier. The same
Operator ID must be
used throughout the
radio access network.
(a 24-bit value that
can be represented as
A.B.C where A, B, C
are from 0 to 255)
Optional
16773929
1 to 16777215
[bs-name ]
BS name
Optional
empty
string
A string of up to
32 printable
characters.
bs configuration mode
Restoring Default Values for BS General Parameters
After enabling the BS configuration mode you can restore the default values for
one or all of the general BS parameters.
To restore one or all general BS parameters do their default value, run the
following command:
npu(config-bs-66053)# no general [operator-id] [bs-name]
You can restore one parameter to its default value by specifying only that
parameter. For example, to restore only the operator-id to its default value, run
the following command:
4Motion
521
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
npu(config-bs-66053)# no general operator-id
The operator-id will be restored to its default value, while the bs-name parameter
will remain unchanged.
To restore all parameters to their default value, run the following command:
npu(config-bs-66053)# no general
NOTE
Refer to Section 4.8.3.1 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053)# no general [operator-id] [bs-name]
Privilege
Level
10
Command
Modes
bs configuration mode
4.8.3.3
Displaying Configuration Information for BS General
Parameters
To display configuration information of the general parameters of a specific or all
BSs, run the following command:
npu# show general bs [<(1 to 16777215 StepSize 1)>]
Specify the BS ID (1-16777215) of an existing BS if you want to display
configuration information for a particular BS. Do not specify values for this
parameter if you want to view configuration information for all existing BSs.
Command
Syntax
npu# show general bs [<(1 to 16777215 StepSize 1)> ]
Privilege
Level
4Motion
522
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Display
Format
(for each
existing BS
if requested
for all BSs)
Command
Modes
4.8.4
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
[<(1 to 16777215
StepSize 1)> ]
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the general
parameters of a specific BS.
Do not specify a value for this
parameter if you want to
display the general
parameters of all BSs.
BSIDLSB
:
OperatorID
:
BSName
:
Global command mode
Managing BS Services
The BS Service parameters affect the properties of the HARQ mechanism for each
Service.
4.8.4.1
Enabling the BS Service Configuration Mode\Creating a BS
Service
To configure the parameters of a BS Service, first enable the BS service
configuration mode for the specific service. Run the following command to enable
the BS service configuration mode. You can also use this command to create a
new service with default values.
npu(config-bs-66053)# service <(string (32))>
For example, to define a new service named video, or to enable the configuration
mode for an existing service named video, run the following command:
npu(config-bs-66053)# service video
4Motion
523
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
If you use this command to create a new service, the configuration mode for this
service is automatically enabled, after which you can execute any of the following
tasks:
Configure the parameters of the service (refer to Section 4.8.4.2)
Restore the default values for the non-mandatory parameters of the service
(refer to Section 4.8.4.3)
After executing the above tasks, you can terminate the BS Service configuration
mode (refer to Section 4.8.4.4) and return to the BS configuration mode. From the
BS configuration mode you can delete an existing service (refer to Section 4.8.4.5).
You can display configuration information for BS services from the global
command mode (refer to Section 4.8.4.6).
Note that for properly completing the configuration of a service the apply
command must be executed prior to exiting the BS Service configuration mode.
Command
Syntax
npu(config-bs-66053)# service <(string (32))>
Privilege
Level
10
Syntax
Description
Command
Modes
4.8.4.2
Parameter
Description
Presence
Default
Value
Possible
Values
<(string (32))>
The Service name (type).
Mandatory
N/A
A string of 1 to
32 characters.
bs configuration mode
Configuring Service Parameters
To configure the BS Service Parameters:
From the BS configuration mode, run the following command:
npu(config-bs-66053-service-video)# def [max-dl-rtx <(0 to 15
StepSize1)> ] [max-ul-rtx <(0 to 15 StepSize 1)> ] [max-subburst
4Motion
524
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
<(0 to 1500 StepSize 1)> ] [trgt-err-rate <(0.1 to 10 StepSize
0.1)> ]
IMPORTANT
When creating a new Service, at least one of the Service parameters must be configured explicitly
(even if configured to the default value).
Command
Syntax
npu(config-bs-66053-service-video)# def [max-dl-rtx <(0 to 15
StepSize1)> ] [max-ul-rtx <(0 to 15 StepSize 1)> ] [max-subburst
<(0 to 1500 StepSize 1)> ] [trgt-err-rate <(0.1 to 10 StepSize
0.1)> ]
Privilege
Level
10
Syntax
Description
Command
Modes
4.8.4.3
Parameter
Description
Presence
Default
Value
Possible
Values
[max-dl-rtx <(0 to 15
StepSize1)> ]
The maximal number of
downlink retransmissions of
an HARQ sub-burst for this
servic
Optional
0 -15i
[max-ul-rtx <(0 to 15
StepSize 1)> ]
The maximal number of
uplink retransmissions of an
HARQ sub-burst for this
service
Optional
0 - 15
[max-subburst <(0 to
1500 StepSize 1)> ]
The maximal size of a
sub-burst in bytes for this
service
Optional
600
0 - 1500
[trgt-err-rate <(0.1 to
10 StepSize 0.1)>]
The target sub-burst error
rate for this service
Optional
0.1 to 10 in
steps of 0.1
bs service configuration mode
Restoring Default Values for BS Service Parameters
After enabling the BS Service configuration mode you can restore the default
values for some or all of the non-mandatory parameters.
4Motion
525
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
To restore one or several BS Service parameters do their default value, run the
following command:
npu(config-bs-66053-service-video)# no def [max-dl-rtx ]
[max-ul-rtx ] [max-subburst ] [trgt-err-rate ]
You can restore one or several parameters to the default value(s) by specifying
only those parameter. For example, to restore only the max-dl-rtx and max-ul-rtx
parameters to their default values, run the following command:
npu(config-bs-66053-service-video)# no def max-dl-rtx max-ul-rtx
The max-dl-rtx and max-ul-rtx parameters will be restored to their default values,
while all other parameters will remain unchanged.
To restore all parameters to their default value, run the following command:
npu(config-bs-66053-service-video)# no def
NOTE
Refer to Section 4.8.4.2 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-service-video)# no def [max-dl-rtx ]
[max-ul-rtx ] [max-subburst ] [trgt-err-rate ]
Privilege
Level
10
Command
Modes
bs service configuration mode
4.8.4.4
Terminating the BS Service Configuration Mode
Run the following command to terminate the BS Service configuration mode:
npu(config-bs-66053-service-video)# exit
IMPORTANT
Do not forget to execute the apply command before terminating the
BS Service configuration mode:
npu(config-bs-66053-service-video)# apply
4Motion
526
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Command
Syntax
npu(config-bs-66053-service-video)# exit
Privilege
Level
10
Command
Modes
bs service configuration mode
4.8.4.5
Deleting a BS Service
Run the following command from the BS configuration mode to delete a BS
Service:
npu(config-bs 66053)# no service
Command
Syntax
npu(config-bs 66053)# no service
Privilege
Level
10
Syntax
Description
Command
Modes
4.8.4.6
Parameter
Description
Presence
Default
Value
Possible
Values
The Service name
Mandatory
N/A
String
bs service configuration mode
Displaying Configuration Information for BS Service
To display configuration information of a specific or all BS Services, run the
following command:
npu# show service bs [<(1 to 16777215 StepSize 1)> service-name ]
Specify the BS ID and Service name if you want to display configuration
information for a particular Service. Do not specify values for these parameter if
you want to view configuration information for all existing BS Services.
4Motion
527
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Command
Syntax
npu# show service bs [<(1 to 16777215 StepSize 1)> service-name ]
Privilege
Level
Syntax
Description
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
The Service name
Optional
N/A
String
Specify a value for this
parameter if you want to
display the parameters of a
specific BS Service. Do not
specify a value for this
parameter if you want to
display the parameters of all
BS Services.
Specify a value for this
parameter if you want to
display the parameters of a
specific BS Service. Do not
specify a value for this
parameter if you want to
display the parameters of all
BS Services.
Display
Format
(for each
existing
Antenna if
requested
for all
Antennas)
Command
Modes
4Motion
BSIDLSB
:
ServiceName
:
MaximumDownlinkRetransmissions
:
MaximumUplinkRetransmissions
:
MaximumSub-BurstSize(bytes)
:
TargetPacketErrorRate(%)
:
Global command mode
528
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.5
Managing BSs
Managing Service Mapping Rules
Up to 255 Service Mapping Rule may be defined.
To configure a Service Mapping Rule:
Enable the BS Service Mapping Rule configuration mode for the selected
Service Mapping Rule (refer to Section 4.8.5.1)
You can now execute any of the following tasks:
»
Configure one or more of the parameters tables of the Service Mapping
Rule (refer to Section 4.8.5.2)
»
Restore the default values of parameters in one or more of the parameters
tables of the Service Mapping Rule (refer to Section 4.8.5.3)
»
Terminate the Service Mapping Rule configuration mode (refer to
Section 4.8.5.4)
In addition, you can, at any time, display configuration information for each of the
parameters tables of the Service Mapping Rule (refer to Section 4.8.5.6) or delete
an existing Service Mapping Rule (refer to Section 4.8.5.5).
4.8.5.1
Enabling the Service Mapping Rule Configuration
Mode\Creating a Service Mapping Rule
To configure the parameters of a Service Mapping Rule, first enable the BS Service
Mapping Rule configuration mode for the specific Service Mapping Rule. Run the
following command to enable the BS Service Mapping Rule configuration mode.
You can also use this command to create a new Service Mapping Rule.
Note that for a new Service Mapping Rule this command only defines the Service
Mapping Rule index, and that the Service Mapping Rule is not fully created until
completing configuration of all mandatory parameters and executing the apply
command (must be executed before exiting the BS Service Mapping Rule
configuration mode). Also when updating an existing Service Mapping Rule, the
apply command must be executing prior to termination the Service Mapping Rule
configuration mode.
npu(config-bs-66053)# srvcmaprule <(1 to 255 StepSize 1)
For example, to define a new Service Mapping Rule index 1, or to enable the
configuration mode for Service Mapping Rule 1, run the following command:
4Motion
529
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
npu(config-bs-66053)# srvcmaprule 1
If you use this command to create a new Service Mapping Rule, the configuration
mode for this Service Mapping Rule is automatically enabled, after which you can
execute any of the following tasks:
Configure one or more of the parameters tables of the Service Mapping Rule
(refer to Section 4.8.5.2)
Restore the default values of parameters in one or more of the parameters
tables of the Service Mapping Rule (refer to Section 4.8.5.3)
After executing the above tasks, you can terminate the Service Mapping Rule
configuration mode (refer to Section 4.8.5.4) and return to the BS configuration
mode.
Note that for properly completing the configuration of a Service Mapping Rule the
apply command must be executed prior to exiting the BS Service Mapping Rule
configuration mode.
Command
Syntax
npu(config-bs-66053)# srvcmaprule <(1 to 255 StepSize 1)>
Privilege
Level
10
Syntax
Description
Command
Modes
Parameter
Description
Presence
srvcmaprule
<(1 to 255
StepSize 1)>
The Service Mapping Rule
index
Mandatory
Default
Value
Possible
Values
1 - 255
BS configuration mode
For example, to define Service Mapping Rule 1 for BS 66053, run the following
command:
npu(config-bs-66053)# srvcmaprule 1
4Motion
530
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
NOTE
The following examples are for BS Service Mapping Rule configuration mode for bs-66053, service
mapping rule (srvcmaprule)-1.
4.8.5.2
Configuring Service Mapping Rule Parameters
After enabling the Service Mapping Rule configuration mode you can configure the
following parameters tables:
General (refer to Section 4.8.5.2.1)
Order (refer to Section 4.8.5.2.2)
R1 Profile (refer to Section 4.8.5.2.3)
R6 Profile (refer to Section 4.8.5.2.4)
IMPORTANT
After completing the Service Mapping Rule configuration,do not forget to execute the apply
command before exiting the BS Service Mapping Rule configuration mode:
npu(config-bs-66053-srvcmaprule-1)# apply
4.8.5.2.1
Configuring General Service Mapping Rule Parameters
The General Service Mapping Parameters table enables associating the Service
Mapping Rule to a specific Service.
To configure the General Service Mapping Rule parameters, run the following
command:
npu(config-bs-66053-srvcmaprule-1)# general srvc
IMPORTANT
When creating a new Service Mapping Rule, the mandatory srvc parameters must be configured.
Command
Syntax
npu(config-bs-66053-srvcmaprule-1)# general srvc
Privilege
Level
10
4Motion
531
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Managing BSs
Parameter
Description
Presence
[srvc ]
The service type to which the
connection will be mapped.
Mandatory
Default
Value
Must be the same as the
name (type) configured for
the relevant service (refer to
Section 4.8.4).
Possible
Values
A string of 1
to 32 printable
characters.
All service a certain data
delivery type (see
Section 4.8.5.2.3) must
use the same service type
(same HARQ properties).
Command
Modes
4.8.5.2.2
bs service mapping rule configuration mode
Configuring the Order Parameters
The Order Parameters table enables configuring the look-up-order parameter that
defines the order in which conceptual rows of the table are checked to find a
match.
To configure the Order parameters, run the following command:
npu(config-bs-66053-srvcmaprule-1)# order look-up-order <(1 to 255
StepSize 1)>
IMPORTANT
When creating a new Service Mapping Rule, the mandaory order parameter must be configured.
Command
Syntax
npu(config-bs-66053-srvcmaprule-1)# order [look-up-order <(1 to
Privilege
Level
10
4Motion
255 StepSize 1)> ]
532
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Managing BSs
Parameter
Description
Presence
[look-up-order <(1 to
255 StepSize 1)> ]
Defines the order in which the
conceptual rows of the table are
checked to find a match.
Mandatory
Default
Value
Possible
Values
1 to 255
Note: The value of this
parameter must be different for
each conceptual row instance
Command
Modes
4.8.5.2.3
bs service mapping rule configuration mode
Configuring R1 Profile Parameters
To configure mapping rules to R1 Profile parameters, run the following command:
npu(config-bs-66053-srvcmaprule-1)# r1prof [modify-serviceqos
{TRUE | FALSE} ] [dfltpriority <(0 to 7 StepSize 1)> ]
[datadeliverytype {uGS | rTVR | nRTVR | bE | eRTVR} ] [priority <(0
to 7 StepSize 1)> ] [mir <(0 to 20000 StepSize 1)> ] [cir <(0 to
20000 StepSize 1)> ] [jitter <(0 to 5000 StepSize 1)> ] [latency
<(0 to 5000 StepSize 1)> ] [sdu-length {fixed | variable} ]
[sdu-size <(1 to 255 StepSize 1)> ] [grant-interval <(0 to 5000
StepSize 1)> ]
IMPORTANT
When creating a new Service Mapping Rule, all mandatory parameters must be configured.
Command
Syntax
npu(config-bs-66053-srvcmaprule-1)# r1prof [modify-serviceqos
{TRUE | FALSE} ] [dfltpriority <(0 to 7 StepSize 1)> ]
[datadeliverytype {uGS | rTVR | nRTVR | bE | eRTVR} ] [priority
<(0 to 7 StepSize 1)> ] [mir <(0 to 20000 StepSize 1)> ] [cir <(0
to 20000 StepSize 1)> ] [jitter <(0 to 5000 StepSize 1)> ]
[latency <(0 to 5000 StepSize 1)> ] [sdu-length{fixed | variable}
] [sdu-size <(1 to 255 StepSize 1)> ] [grant-interval <(0 to 5000
StepSize 1)> ]
Privilege
Level
4Motion
10
533
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
[modify-serviceqos
{TRUE | FALSE} ]
Indicates whether to modify
service QoS parameters
using internal R1 profile
parameters.
Optional
FALSE
TRUE
[dfltpriority <(0 to 7
StepSize 1)> ]
Relevant only if
modify-serviceqos is FALSE.
Indicates the traffic priority to
be used when it is missing in
R6 request.
Optional
0 to 7
[datadeliverytype
{uGS | rTVR |
nRTVR | bE |
eRTVR} ]
Relevant only if
modify-serviceqos is TRUE.
An internal R1 profile
parameter, specifying the
type of data delivery (service
type).
Mandatory
when
creating a
new Service
Mapping
Rule.
N/A
uGS
FALSE
rTVR
nRTVR
bE
(RTVR and NRTVR are not
applicable for current release)
4Motion
eRTVR
[priority <(0 to 7
StepSize 1)> ]
Relevant only if
modify-serviceqos is TRUE
and the datadeliverytype is
rTVR, nRTVR, eRTVR or bE.
An internal R1 profile
parameter specifying the
traffic priority.
Mandatory
when
creating a
new Service
Mapping
Rule.
N/A
0 to 7
[mir <(0 to 20000
StepSize 1)> ]
Relevant only if
modify-serviceqos is TRUE
and the datadeliverytype is
bE or eRTVR. An internal R1
profile parameter specifying
the maximum sustained traffic
rate in Kbps.
Mandatory
when
creating a
new Service
Mapping
Rule.
N/A
0 - 20000
[cir <(0 to 20000
StepSize 1)> ]
Relevant only if
modify-serviceqos is TRUE
and the datadeliverytype is
uGS or eRTVR. An internal
R1 profile parameter
specifying the minimum
reserved traffic rate in Kbps.
Mandatory
when
creating a
new Service
Mapping
Rule.
N/A
0 - 20000
534
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Modes
4Motion
Managing BSs
[jitter <(0 to 5000
StepSize 1)> ]
Relevant only if
modify-serviceqos is TRUE
and the datadeliverytype is
uGS or eRTVR. An internal
R1 profile parameter
specifying maximum tolerated
jitter in milliseconds.
Mandatory
when
creating a
new Service
Mapping
Rule.
N/A
0 - 5000
[latency <(0 to
5000 StepSize 1)>
Relevant only if
modify-serviceqos is TRUE
and the datadeliverytype is
uGS or eRTVR. An internal
R1 profile parameter
specifying maximum latency
in milliseconds.
Mandatory
when
creating a
new Service
Mapping
Rule.
N/A
0 - 5000
[sdu-length{fixed |
variable} ]
Relevant only if
modify-serviceqos is TRUE
and the datadeliverytype is
uGS. An internal R1 profile
parameter specifying whether
SDU length is fixed or
variable. In the current
release only fixed length is
supported.
Optional
fixed
fixed
[sdu-size <(1 to
255 StepSize 1)> ]
Relevant only if
modify-serviceqos is TRUE,
the datadeliverytype is uGS
and the sdu-length is fixed.
An internal R1 profile
parameter specifying the
SDU size in bytes.
Mandatory
when
creating a
new Service
Mapping
Rule.
N/A
1 - 255
[grant-interval <(0
to 5000 StepSize
1)> ]
Relevant only if
modify-serviceqos is TRUE
and the datadeliverytype is
uGS or eRTVR. An internal
R1 profile parameter
specifying the grant interval in
milliseconds.
Mandatory
when
creating a
new Service
Mapping
Rule.
N/A
0 - 5000
variable
(not
supported
in current
release)
bs service mapping rule configuration mode
535
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
IMPORTANT
Note that when creating a new Service Mapping Rule all mandatory parameters must be
configured, including those that may not be relevant for the Service Mapping Rule.
4.8.5.2.4
Configuring R6 Profile Parameters
To configure mapping rules to R6 Profile parameters, run the following command:
npu(config-bs-66053-srvcmaprule-1)# r6prof [datadeliverytype {uGS |
rTVR | nRTVR | bE | eRTVR | any} ] [priority <(-1 to -1 StepSize 1) | (0 to 7
StepSize 1)> ] [mediaflowtype ] [use-mediaflowtype {TRUE | FALSE} ]
[mir <(-1 to -1 StepSize 1) | (0 to 20000 StepSize 1)> ] [cir <(-1 to -1 StepSize 1) |
(0 to 20000 StepSize 1)> ] [latency <(-1 to -1 StepSize 1) | (0 to 5000 StepSize 1)>].
IMPORTANT
When creating a new Service Mapping Rule, at least one of the R6 Profile parameters must be
configured explicitly (even if configured to the default value).
Command
Syntax
npu(config-bs-66053-srvcmaprule-2)# r6prof [datadeliverytype {uGS
| rTVR | nRTVR | bE | eRTVR | any} ] [priority <(-1 to -1 StepSize
1) | (0 to 7 StepSize 1)> ] [mediaflowtype ]
[use-mediaflowtype {TRUE | FALSE} ] [mir <(-1 to -1 StepSize 1) |
(0 to 20000 StepSize 1)> ] [cir <(-1 to -1 StepSize 1) | (0 to
20000 StepSize 1)> ] [latency <(-1 to -1 StepSize 1) | (0 to 5000
StepSize 1)> ]
Privilege
Level
Syntax
Description
4Motion
10
Parameter
Description
Presence
536
Default
Value
Possible
Values
System Manual
Chapter 4 - Operation and Administration Using the CLI
[datadeliverytype
{uGS | rTVR |
nRTVR | bE |
eRTVR | any} ]
Managing BSs
An R6 parameter entry in the
lookup table specifying the
data delivery type (service
type).
Optional
any
uGS
rTVR
nRTVR
bE
eRTVR
any
-1
[priority <(-1 to -1
StepSize 1) | (0 to
7 StepSize 1)> ]
An R6 parameter entry in the
lookup table specifying the
traffic priority. A value of -1
means any.
Optional
[mediaflowtype
]
An R6 parameter entry in the
lookup table that is relevant
only if the use-mediaflowtype
parameter is defined as
TRUE
Optional
blank
string
A string of 32
printable
characters.
[use-mediaflowtyp
e {TRUE | FALSE}
If this parameter has a value
TRUE, the service lookup
function will try to match the
R6 media flow type with the
mediaFlowType entry in the
table.
Optional
FALSE
TRUE
-1
0-7
FALSE
If FALSE the service lookup
function will ignore the R6
media flow type.
4Motion
[mir <(-1 to -1
StepSize 1) | (0 to
20000 StepSize
1)> ]
An R6 parameter entry in the
lookup table specifyingthe
maximum sustained traffic
rate in Kbps. A value of -1
means any.
Optional
[cir <(-1 to -1
StepSize 1) | (0 to
20000 StepSize
1)> ]
An R6 parameter entry in the
lookup table specifying the
minimum reserved traffic rate
in Kbps. A value of -1 means
any.
Optional
[latency <(-1 to -1
StepSize 1) | (0 to
5000 StepSize 1)>
An R6 parameter entry in the
lookup table specifying
tolerated latency in
milliseconds. A value of -1
means any.
Optional
537
-1
-1
0 - 20000
-1
-1
0 - 20000
-1
-1
0 - 5000
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Modes
4.8.5.3
Managing BSs
bs service mapping rule configuration mode
Restoring Default Values for Service Mapping Rule
Configuration Parameters
After enabling the Service Mapping Rule configuration mode you can restore the
default values for non-mandatory parameters in the following parameters tables:
R1 Profile (refer to Section 4.8.5.3.1)
R6 Profile (refer to Section 4.8.5.3.2)
4.8.5.3.1
Restoring the Default Values of RI Profile Parameters
To restore some or all of R1 Profile non-mandatory parameters to their default
values, run the following command:
npu(config-bs-66053-srvcmaprule-1)# no r1prof [modify-serviceqos ]
[dfltpriority ]
You can restore only one or several parameters to the default values by specifying
only those parameters. For example, to restore only the dfltpriority to the default
value, run the following command:
npu(config-bs-66053-srvcmaprule-1)# no r1prof dfltpriority
The parameter will be restored to its default value, while the other parameters will
remain unchanged.
To restore all R1 Profile non-mandatory parameters to their default value, run the
following command:
npu(config-bs-66053-srvcmaprule-1)# no r1prof
NOTE
Refer to Section 4.8.5.2.3 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-srvcmaprule-1)# no r1prof [modify-serviceqos ]
Privilege
Level
10
4Motion
[dfltpriority ]
538
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Modes
4.8.5.3.2
Managing BSs
bs service mapping rule configuration mode
Restoring the Default Values of R6 Profile Parameters
To restore some or all of R6 Profile parameters to their default values, run the
following command:
npu(config-bs-66053-srvcmaprule-1)# no r6prof [datadeliverytype ]
[priority ] [mediaflowtype ] [use-mediaflowtype] [mir ] [cir ]
[latency ]
You can restore only one or several parameters to the default values by specifying
only those parameters. For example, to restore only the mir and cir to the default
values, run the following command:
npu(config-bs-66053-srvcmaprule-1)# no r6prof mir cir
These parameter will be restored to their default values, while all other
parameters will remain unchanged.
To restore all R6 Profile parameters to their default value, run the following
command:
npu(config-bs-66053-srvcmaprule-1)# no r6prof
NOTE
Refer to Section 4.8.5.2.4 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-srvcmaprule-1)# no r6prof [datadeliverytype ]
[priority ] [mediaflowtype ] [use-mediaflowtype] [mir ] [cir ]
[latency ]
Privilege
Level
10
Command
Modes
bs service mapping rule configuration mode
4.8.5.4
Terminating the Service Mapping Rule Configuration Mode
Run the following command to terminate the Service Mapping Rule configuration
mode:
4Motion
539
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
npu(config-bs-66053-srvcmaprule-1)# exit
IMPORTANT
Do not forget to execute the apply command before terminating the BS Service Mapping Rule
configuration mode:
npu(config-bs-66053-srvcmaprule-1)# apply
Command
Syntax
npu(config-bs-66053-servmaprule-1)# exit
Privilege
Level
10
Command
Modes
bs service mapping rule configuration mode
4.8.5.5
Deleting a Service Mapping Rule
Run the following command from the BS configuration mode to delete a Service
Mapping Rule:
npu(config-bs 66053)# no srvcmaprule <(1 to 255 StepSize 1)>
Command
Syntax
npu(config-bs 66053)# no srvcmaprule <(1 to 255 StepSize 1)>
Privilege
Level
10
Syntax
Description
Command
Modes
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 255
StepSize 1)>
The Service Mapping Rule
index
Mandatory
N/A
1-255
bs configuration mode
540
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.5.6
Managing BSs
Displaying Configuration Information for Service Mapping
Rules
You can display the current configuration information for the following
parameters tables:
General (refer to Section 4.8.5.6.1)
Order (refer to Section 4.8.5.6.2)
R1 Profile (refer to Section 4.8.5.6.3)
R6 Profile (refer to Section 4.8.5.6.4)
All (refer to Section 4.8.5.6.5)
4.8.5.6.1
Displaying Configuration Information for General Service Mapping
Rule Parameters
To display configuration for the general parameters of a specific or all Service
Mapping Rules, run the following command:
npu# show srvcmaprule-general bs [<(1 to 16777215 StepSize 1)> rule-index <(1
to 255 StepSize 1)>]
Specify the BS ID and Service Mapping Rule index if you want to display
configuration for a particular Service Mapping Rule. For example, to display the
General parameters of Service Mapping Rule 1 in BS 66053, run the following
command:
npu# show srvcmaprule-general bs 66053 rule-index 1
Do not specify these parameters if you want to view configuration information for
all existing Service Mapping Rules. To display information for all Service Mapping
Rules, run the following command:
npu# show srvcmaprule-general bs
Command
Syntax
npu# show srvcmaprule-general bs [<(1 to 16777215 StepSize 1)> rule-index <(1 to 255
StepSize 1)> ]
Privilege
Level
4Motion
541
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Display
Format
(for each
existing
Service
Mapping
Rule if
requested
for all
Service
Mapping
Rules)
Command
Modes
4.8.5.6.2
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
rule-index <(1 to
255 StepSize 1)> ]
The Service Mapping Rule
index. To be used only if you
want to display the general
parameters of a specific
Service Mapping Rule.
Optional
N/A
1-255
Specify a value for this
parameter if you want to
display the general
parameters of a specific
Service Mapping Rule. Do not
specify a value for this
parameter if you want to
display the general
parameters of all Service
Mapping Rules.
BSIDLSB
:
MappingRuleIndex
:
ServiceName
:
Global command mode
Displaying Configuration Information for Service Mapping Rule Order
Parameters
To display configuration for the order parameters of a specific or all Service
Mapping Rules, run the following command:
npu# show srvcmaprule-order bs [<(1 to 16777215 StepSize 1)> rule-index <(1 to
255 StepSize 1)>]
4Motion
542
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Specify the BS ID and Service Mapping Rule index if you want to display
configuration for a particular Service Mapping Rule. For example, to display the
order parameters of Service Mapping Rule 1 in BS 66053, run the following
command:
npu# show srvcmaprule-order bs 66053 rule-index 1
Do not specify these parameters if you want to view configuration information for
all existing Service Mapping Rules. To display information for all Service Mapping
Rules, run the following command:
npu# show srvcmaprule-order bs
Command
Syntax
npu# show srvcmaprule-order bs [<(1 to 16777215 StepSize 1)> rule-index <(1 to 255 StepSize
1)> ]
Privilege
Level
Syntax
Description
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
rule-index <(1 to 255
StepSize 1)>]
The Service Mapping Rule
index. To be used only if you
want to display the order
parameters of a specific
Service Mapping Rule.
Optional
N/A
1-255
Specify a value for this
parameter if you want to
display the order parameters
of a specific Service Mapping
Rule. Do not specify a value
for this parameter if you want
to display the order
parameters of all Service
Mapping Rules.
543
System Manual
Chapter 4 - Operation and Administration Using the CLI
Display
Format
(for each
existing
Service
Mapping
Rule if
requested
for all
Service
Mapping
Rules)
Command
Modes
4.8.5.6.3
Managing BSs
BSIDLSB
:
MappingRuleIndex
:
LookUpOrder
:
Global command mode
Displaying Configuration Information for Service Mapping Rule R1
Profile Parameters
To display configuration for the R1 Profile parameters of a specific or all Service
Mapping Rules, run the following command:
npu# show srvcmaprule-r1prof bs [<(1 to 16777215 StepSize 1)> rule-index <(1
to 255 StepSize 1)>]
Specify the BS ID and Service Mapping Rule index if you want to display
configuration for a particular Service Mapping Rule. For example, to display the
R1 Profile parameters of Service Mapping Rule 1 in BS 66053, run the following
command:
npu# show srvcmaprule-r1prof bs 66053 rule-index 1
Do not specify these parameters if you want to view configuration information for
all existing Service Mapping Rules. To display information for all Service Mapping
Rules, run the following command:
npu# show srvcmaprule-r1prof bs
Command
Syntax
npu# show srvcmaprule-r1prof bs [<(1 to 16777215 StepSize 1)> rule-index <(1 to 255 StepSize
1)> ]
Privilege
Level
4Motion
544
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Display
Format
(for each
existing
Service
Mapping
Rule if
requested
for all
Service
Mapping
Rules)
Command
Modes
4Motion
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
rule-index <(1 to 255
StepSize 1)>]
The Service Mapping Rule
index. To be used only if you
want to display the R1 Profile
parameters of a specific
Service Mapping Rule.
Optional
N/A
1-255
Specify a value for this
parameter if you want to
display the R1 Profile
parameters of a specific
Service Mapping Rule. Do not
specify a value for this
parameter if you want to
display the R1 Profile
parameters of all Service
Mapping Rules.
BSIDLSB
:
MappingRuleIndex
:
ModifyServiceQoSParameters
:
DefaultPriority
:
DataDeliveryTypeR1Profile
:
PriorityR1Profile
:
MIRR1Profile
:
CIRR1Profile
:
Jitter
:
LatencyR1Profile
:
SDULength
:
SDUSize
:
Global command mode
545
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.5.6.4
Managing BSs
Displaying Configuration Information for Service Mapping Rule R6
Profile Parameters
To display configuration for the R6 Profile parameters of a specific or all Service
Mapping Rules, run the following command:
npu# show srvcmaprule-r6prof bs [<(1 to 16777215 StepSize 1)> rule-index <(1
to 255 StepSize 1)>]
Specify the BS ID and Service Mapping Rule index if you want to display
configuration for a particular Service Mapping Rule. For example, to display the
R6 Profile parameters of Service Mapping Rule 1 in BS 66053, run the following
command:
npu# show srvcmaprule-r6prof bs 66053 rule-index 1
Do not specify these parameters if you want to view configuration information for
all existing Service Mapping Rules. To display information for all Service Mapping
Rules, run the following command:
npu# show srvcmaprule-r6prof bs
Command
Syntax
npu# show srvcmaprule-r6prof bs [<(1 to 16777215 StepSize 1)> rule-index <(1 to 255 StepSize
1)> ]
Privilege
Level
Syntax
Description
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the R6 Profile
parameters of a specific
Service Mapping Rule. Do not
specify a value for this
parameter if you want to
display the general
parameters of all Service
Mapping Rules.
546
System Manual
Chapter 4 - Operation and Administration Using the CLI
rule-index <(1 to 255
StepSize 1)>]
Display
Format
(for each
existing
Service
Mapping
Rule if
requested
for all
Service
Mapping
Rules)
Command
Modes
4.8.5.6.5
Managing BSs
The Service Mapping Rule
index. To be used only if you
want to display the R6 Profile
parameters of a specific
Service Mapping Rule.
Optional
N/A
BSIDLSB
:
MappingRuleIndex
:
DataDeliveryTypeR6Profile
:
PriorityR6Profile
:
MediaFlowType
:
UseMediaFlowType
:
CIRR6Profile
:
MIRR6Profile
:
LatencyR6Profile
:
1-255
Global command mode
Displaying Configuration Information for All Service Mapping Profile
Parameters
To display all configuration parameters of a specific or all Service Mapping Rules,
run the following command:
npu# show srvcmaprule-all bs [<(1 to 16777215 StepSize 1)> rule-index <(1 to
255 StepSize 1)>]
Specify the BS ID and Service Mapping Rule index if you want to display
configuration for a particular Service Mapping Rule. For example, to display all
parameters of Service Mapping Rule 1 in BS 66053, run the following command:
npu# show srvcmaprule-all bs 66053 rule-index 1
Do not specify these parameters if you want to view configuration information for
all existing Service Mapping Rules. To display information for all Service Mapping
Rules, run the following command:
npu# show srvcmaprule-all bs
4Motion
547
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Command
Syntax
npu# show srvcmaprule-all bs [<(1 to 16777215 StepSize 1)> rule-index <(1 to 255 StepSize 1)>]
Privilege
Level
10
Syntax
Description
Command
Modes
4.8.6
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
rule-index <(1 to 255
StepSize 1)>]
The Service Mapping Rule
index. To be used only if you
want to display all parameters
of a specific Service Mapping
Rule.
Optional
N/A
1-255
Specify a value for this
parameter if you want to
display all parameters of a
specific Service Mapping
Rule. Do not specify a value
for this parameter if you want
to display all parameters of all
Service Mapping Rules.
Global command mode
Managing Power Control Levels and Policies
To configure a the Power Control Levels and Policies:
4Motion
Enable the Power Control configuration mode (refer to Section 4.8.6.1)
548
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
You can now execute any of the following tasks:
»
Configure one or more of the Power Control parameters tables (refer to
Section 4.8.6.2)
»
Restore the default values of parameters in one or more of the Power
Control parameters tables (refer to Section 4.8.6.3)
»
Terminate the Power Control configuration mode (refer to Section 4.8.6.4)
In addition, you can, at any time, display configuration information for each of the
parameters tables (refer to Section 4.8.6.5).
4.8.6.1
Enabling the Power Control Configuration Mode
To configure the Power Control parameters, first enable the Power Control
configuration mode. Run the following command to enable the Power Control
configuration mode.
Note that for properly completing the configuration the apply command must be
executed prior to exiting the Power Control configuration mode.
npu(config-bs-66053)# pwrctrl
The Power Control configuration mode is enabled, after which you can execute
any of the following tasks:
Configure one or more of the Power Control parameters tables (refer to
Section 4.8.6.2)
Restore the default values of parameters in one or more of the parameters
tables (refer to Section 4.8.6.3)
After executing the above tasks, you can terminate the Power Control
configuration mode (refer to Section 4.8.6.4) and return to the BS configuration
mode.
Note that for properly completing the Power Control configuration the apply
command must be executed prior to exiting the Power Control configuration
mode.
Command
Syntax
4Motion
npu(config-bs-66053)# pwrctrl
549
System Manual
Chapter 4 - Operation and Administration Using the CLI
Privilege
Level
10
Command
Modes
bs configuration mode
4.8.6.2
Managing BSs
Configuring Power Control Parameters
After enabling the Power Control configuration mode you can configure the
following parameters tables:
Target Noise and Interference Level (refer to Section 4.8.6.2.1)
Maximum EIRP (refer to Section 4.8.6.2.2)
Required C/N Level (refer to Section 4.8.6.2.3)
Open Loop Correction Policy (refer to Section 4.8.6.2.4)
Open Loop Correction Range (refer to Section 4.8.6.2.5)
Closed Loop - Unstable MS (refer to Section 4.8.6.2.6)
Closed Loop - MS in Network Entry (refer to Section 4.8.6.2.7)
Closed Loop Correction Range (refer to Section 4.8.6.2.8)
IMPORTANT
After completing the Power Control configuration,do not forget to execute the apply command
before exiting the Power Control configuration mode:
npu(config-bs-66053-pwrctrl)# apply
4.8.6.2.1
Configuring Power Control Target Noise and Interference Level
Parameters
The Target Noise and Interference Level table enables defining the target limits for
various noise and interference levels.
To configure the Target Noise and Interference Levels, run the following command:
npu(config-bs-66053-pwrctrl)# nilevels [cqi-ack-ranging <(-150 to -22.5
StepSize 0.5)>] [pusc <(-150 to -22.5 StepSize 0.5)>]
4Motion
550
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
IMPORTANT
When creating a new BS, at least one of the Power Control Target Noise and Interference Level
parameters must be configured explicitly (even if configured to the default value).
Command
Syntax
npu(config-bs-66053-pwrctrl)# nilevels [cqi-ack-ranging <(-150 to
Privilege
Level
10
Syntax
Description
Command
Modes
4.8.6.2.2
-22.5 StepSize 0.5)> ] [pusc <(-150 to -22.5 StepSize 0.5)> ]
Parameter
Description
Presence
Default
Value
Possible
Values
[cqi-ack-ran
ging <(-150
to -22.5
StepSize
0.5)> ]>
Target Noise and interference
level for the CQI, ACK and
periodic ranging regions, in
dBm.
Optional
-128
-150 to -22.5 in
steps of 0.5
[pusc <(-150
to -22.5
StepSize
0.5)> ]
Target Noise and interference
level for the PUSC zone, in
dBm
Optional
-128
-150 to -22.5 in
steps of 0.5
bs power control configuration mode
Configuring the Power Control Maximum EIRP
The maxeirxp parameter enables defining the maximum effective isotropic
received power at the BS for Initial ranging.
To configure the maxeirxp, run the following command:
npu(config-bs-66053-pwrctrl)# maxeirxp <(-140 to -40 StepSize 1)>
IMPORTANT
When creating a new BS, the maxeirxp parameters must be configured explicitly (even if configured
to the default value).
4Motion
551
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Command
Syntax
npu(config-bs-66053-pwrctrl)# maxeirxp <(-140 to -40 StepSize 1)>
Privilege
Level
10
Syntax
Description
Command
Modes
4.8.6.2.3
Parameter
Description
Presence
Default
Value
Possible
Values
maxeirxp <(-140 to
-40 StepSize 1)>
The maximum effective
isotropic received power at
the BS for Initial ranging, in
dBm.
Optional
-124
-140 to -40
bs power control configuration mode
Configuring the Power Control Required C/N Level Parameters
The Required C/N Levels table enables defining the Carrier to Noise Ratios
required for various types of transmissions.
To configure the Required C/N Levels, run the following command:
npu(config-bs-66053-pwrctrl)# requiredcnr [ack <(-20 to 50 StepSize 1)>] [cqi
<(-20 to 50 StepSize 1)>] [cdma <(-20 to 50 StepSize 1)>] [qpsk-1by2 <(-20 to 50
StepSize 1)>] [qpsk-3by4 <(-20 to 50 StepSize 1)>] [qam16-1by2 <(-20 to 50
StepSize 1)>] [qam16-3by4 <(-20 to 50 StepSize 1)>] [qam64-1by2 <(-20 to 50
StepSize 1)>] [qam64-2by3 <(-20 to 50 StepSize 1)>] [qam64-3by4 <(-20 to 50
StepSize 1)>] [qam64-5by6 <(-20 to 50 StepSize 1)>]
IMPORTANT
When creating a new BS, at least one of the Power Control Required C/N Level parameters must
be configured explicitly (even if configured to the default value).
4Motion
552
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Syntax
Managing BSs
npu(config-bs-66053-pwrctrl)# requiredcnr [ack <(-20 to 50
StepSize 1)> ] [cqi <(-20 to 50 StepSize 1)> ] [cdma <(-20 to 50
StepSize 1)> ] [qpsk-1by2 <(-20 to 50 StepSize 1)> ] [qpsk-3by4
<(-20 to 50 StepSize 1)> ] [qam16-1by2 <(-20 to 50 StepSize 1)> ]
[qam16-3by4 <(-20 to 50 StepSize 1)> ] [qam64-1by2 <(-20 to 50
StepSize 1)> ] [qam64-2by3 <(-20 to 50 StepSize 1)> ] [qam64-3by4
<(-20 to 50 StepSize 1)> ] [qam64-5by6 <(-20 to 50 StepSize 1)> ]
Privilege
Level
Syntax
Description
10
Parameter
Description
Presence
Default
Value
Possible
Values
[ack <(-20 to 50
StepSize 1)> ]
The C/N in dB required for
sending ACK, reported to the MS
for power control purposes.
Optional
-20 to 50
[cqi <(-20 to 50
StepSize 1)> ]
The C/N in dB required for
sending CQI, reported to the MS
for power control purposes.
Optional
-20 to 50
Optional
-20 to 50
Optional
14
-20 to 50
Must be in the range from
requiredcnr-ack - 8 to
requiredcnr-ack + 7 (see ack
parameter above)
[cdma <(-20 to 50
StepSize 1)> ]
The C/N in dB required for
transmitting CDMA, reported to
the MS for power control
purposes.
Must be in the range from
requiredcnr-cqi - 8 to
requiredcnr-cqi + 7 (see cqi
parameter above)
[qpsk-1by2 <(-20 to
50 StepSize 1)> ]
The C/N in dB required for
transmitting using QPSK 1/2,
reported to the MS for power
control purposes.
Must be in the range from
requiredcnr-cdma - 16 to
requiredcnr-cdma + 14 (see cdma
parameter above)
4Motion
553
System Manual
Chapter 4 - Operation and Administration Using the CLI
[qpsk-3by4<(-20 to
50 StepSize 1)> ]
Managing BSs
The C/N in dB required for
transmitting using QPSK 3/4,
reported to the MS for power
control purposes.
Optional
16
-20 to 50
Optional
18
-20 to 50
Optional
22
-20 to 50
Optional
23
-20 to 50
Optional
23
-20 to 50
Must be in the range from
requiredcnr-qpsk-1by2 - 16 to
requiredcnr-qpsk-1by2 + 14 (see
qpsk-1by2 parameter above)
[qam16-1by2 <(-20
to 50 StepSize 1)> ]
The C/N in dB required for
transmitting using 16QAM 1/2,
reported to the MS for power
control purposes.
Must be in the range from
requiredcnr-qpsk-3by4 - 8 to
requiredcnr-qpsk-3by4 + 7 (see
qpsk-3by4 parameter above)
[qam16-3by4 <(-20
to 50 StepSize 1)> ]
The C/N in dB required for
transmitting using 16QAM 3/4,
reported to the MS for power
control purposes.
Must be in the range from
requiredcnr-qam16-1by2 - 16 to
requiredcnr-qam16-1by2 + 14
(see qam16-1by2 parameter
above)
qam64-1by2 <(-20
to 50 StepSize 1)> ]
The C/N in dB required for
transmitting using 64QAM 1/2,
reported to the MS for power
control purposes.
Must be in the range from
requiredcnr-qam16-3by4 - 16 to
requiredcnr-qam16-3by4 + 14
(see qam16-3by4 parameter
above)
[qam64-2by3 <(-20
to 50 StepSize 1)> ]
The C/N in dB required for
transmitting using 64QAM 2/3,
reported to the MS for power
control purposes.
Must be in the range from
requiredcnr-qam64-1by2 - 8 to
requiredcnr-qam64-1by2 + 7 (see
qam64-1by2 parameter above)
4Motion
554
System Manual
Chapter 4 - Operation and Administration Using the CLI
[qam64-3by4 <(-20
to 50 StepSize 1)> ]
Managing BSs
The C/N in dB required for
transmitting using 64QAM 3/4,
reported to the MS for power
control purposes.
Optional
23
-20 to 50
Optional
23
-20 to 50
Must be in the range from
requiredcnr-qam64-2by3 - 8 to
requiredcnr-qam54-2by3 + 7 (see
qam54-2by3 parameter above)
[qam64-5by6 <(-20
to 50 StepSize 1)> ]
he C/N in dB required for
transmitting using 64QAM 5/6,
reported to the MS for power
control purposes.
Must be in the range from
requiredcnr-qam64-3by4 - 8 to
requiredcnr-qam64-3by4 + 7 (see
qam64-3by4 parameter above)
Command
Modes
4.8.6.2.4
bs power control configuration mode
Configuring the Power Control Open Loop Correction Policy
Parameters
To configure the Open Loop Correction Policy parameters, run the following
command:
npu(config-bs-66053-pwrctrl)# olpolicy [positivecoefficient <(0 to 1 StepSize
0.05)>] [negativecoefficient<(0 to 1 StepSize 0.05)>] [max-positivecorrection <(0 to
20 StepSize 0.1)>] [max-negativecorrection <(0 to 20 StepSize 0.1)>]
IMPORTANT
When creating a new BS, at least one of the Power Control Open Loop Correction Policy
parameters must be configured explicitly (even if configured to the default value).
Command
Syntax
npu(config-bs-66053-pwrctrl)# olpolicy [positivecoefficient <(0 to
1 StepSize 0.05)> ] [negativecoefficient<(0 to 1 StepSize 0.05)> ]
[max-positivecorrection <(0 to 20 StepSize 0.1)> ]
[max-negativecorrection <(0 to 20 StepSize 0.1)> ]
Privilege
Level
10
4Motion
555
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Command
Modes
4.8.6.2.5
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
[positivecoefficient
<(0 to 1 StepSize
0.05)> ]
Correction coefficient for
open loop when giving
positive corrections
Optional
0.7
0 to 1 in steps
of 0.05
[negativecoefficien
t <(0 to 1 StepSize
0.05)> ]
Correction coefficient for
open loop when giving
negative corrections
Optional
0.7
0 to 1 in steps
of 0.05
[max-positivecorre
ction <(0 to 20
StepSize 0.1)> ]
Maximum positive power
correction (in dB) for open
loop
Optional
0 to 20 in steps
of 0.1
[max-negativecorr
ection <(0 to 20
StepSize 0.1)> ]
Maximum negative power
correction (in dB) for open
loop
Optional
0 to 20 in steps
of 0.1
bs power control configuration mode
Configuring the Power Control Open Loop Correction Range
Parameters
To configure the Open Loop Correction Range parameters, run the following
command:
npu(config-bs-66053-pwrctrl)# olrange [lowthrshld-linear <(-20 to 0 StepSize
0.1)>] [lowthrshld-constant <(-20 to 0 StepSize 0.1)>] [highthrshld-linear <(0 to 20
StepSize 0.1)>] [highthrshld-constant <(0 to 20 StepSize 0.1)>]
IMPORTANT
When creating a new BS, at least one of the Power Control Open Loop Correction Range
parameters must be configured explicitly (even if configured to the default value).
Command
Syntax
npu(config-bs-66053-pwrctrl)# olrange [lowthrshld-linear <(-20 to
0 StepSize 0.1)> ] [lowthrshld-constant <(-20 to 0 StepSize 0.1)>
] [highthrshld-linear <(0 to 20 StepSize 0.1)> ]
[highthrshld-constant <(0 to 20 StepSize 0.1)> ]
Privilege
Level
10
4Motion
556
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
[lowthrshld-linear
<(-20 to 0 StepSize
0.1)> ]
The open loop correction
range threshold (in dB) below
which linear corrections are
made.
Optional
-18
-20 to 0 in
steps of 0.1
Cannot be lower than
olrange-lowthrshld-constant
(see below)
[lowthrshld-consta
nt <(-20 to 0
StepSize 0.1)> ]
The open loop correction
range threshold (in dB) below
which constant corrections
are made.
Optional
-19
-20 to 0 in
steps of 0.1
[highthrshld-linear
<(0 to 20 StepSize
0.1)> ]
The open loop correction
range threshold (in dB) above
which linear corrections are
made.
Optional
18
0 to 20 in steps
of 0.1
[highthrshld-consta
nt <(0 to 20
StepSize 0.1)> ]
The open loop correction
range threshold (in dB) above
which constant corrections
are made.
Optional
19
0 to 20 in steps
of 0.1
Cannot be lower than
olrange-highthrshld-linear
(see above)
Command
Modes
4.8.6.2.6
bs power control configuration mode
Configuring the Power Control Closed Loop - Unstable MS Correction
Policy Parameters
To configure the Closed Loop - Unstable MS Correction Policy parameters, run the
following command:
npu(config-bs-66053-pwrctrl)# clunstable [positivecoefficient <(0 to 1 StepSize
0.05)>] [negativecoefficient <(0 to 1 StepSize 0.05)>] [max-positivecorrection <(0 to
20 StepSize 0.1)>][max-negativecorrection <(0 to 20 StepSize 0.1)>]
IMPORTANT
When creating a new BS, at least one of the Power Control Closed Loop - Unstable MS parameters
must be configured explicitly (even if configured to the default value).
4Motion
557
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Syntax
Managing BSs
npu(config-bs-66053-pwrctrl)# clunstable [positivecoefficient <(0
to 1 StepSize 0.05)> ] [negativecoefficient <(0 to 1 StepSize
0.05)> ] [max-positivecorrection <(0 to 20 StepSize 0.1)>
][max-negativecorrection <(0 to 20 StepSize 0.1)> ]
Privilege
Level
Syntax
Description
Command
Modes
4.8.6.2.7
10
Parameter
Description
Presence
Default
Value
Possible
Values
[positivecoefficient
<(0 to 1 StepSize
0.05)> ]
Correction coefficient for
problematic MS in a closed
loop when giving positive
corrections
Optional
0.8
0 to 1 in steps
of 0.05
[negativecoefficien
t <(0 to 1 StepSize
0.05)> ]
Correction coefficient for
problematic MS in a closed
loop when giving negative
corrections
Optional
0.7
0 to 1 in steps
of 0.05
[max-positivecorre
ction <(0 to 20
StepSize 0.1)> ]
Maximum positive power
correction (in dB) for
problematic MS in a closed
loop
Optional
0 to 20 in steps
of 0.1
[max-negativecorr
ection <(0 to 20
StepSize 0.1)> ]
Maximum negative power
correction (in dB) for
problematic MS in a closed
loop
Optional
0 to 20 in steps
of 0.1
bs power control configuration mode
Configuring the Power Control Closed Loop - MS in Network Entry
Correction Policy Parameters
To configure the Closed Loop - MS in Network Entry Correction Policy parameters,
run the following command:
npu(config-bs-66053-pwrctrl)# clne [positivecoefficient <(0 to 1 StepSize 0.05)>]
[negativecoefficient <(0 to 1 StepSize 0.05)>] [max-positivecorrection <(0 to 20
StepSize 0.1)>] [max-negativecorrection <(0 to 20 StepSize 0.1)>]
4Motion
558
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
IMPORTANT
When creating a new BS, at least one of the Power Control Closed Loop - MS in Network Entry
parameters must be configured explicitly (even if configured to the default value).
Command
Syntax
npu(config-bs-66053-pwrctrl)# clne [positivecoefficient <(0 to 1
StepSize 0.05)> ] [negativecoefficient <(0 to 1 StepSize 0.05)> ]
[max-positivecorrection <(0 to 20 StepSize 0.1)> ]
[max-negativecorrection <(0 to 20 StepSize 0.1)> ]
Privilege
Level
Syntax
Description
Command
Modes
4.8.6.2.8
10
Parameter
Description
Presence
Default
Value
Possible
Values
[positivecoefficient
<(0 to 1 StepSize
0.05)> ]
Correction coefficient for
network entry in closed loop
when giving positive
corrections
Optional
0.7
0 to 1 dB in
steps of 0.05
[negativecoefficien
t <(0 to 1 StepSize
0.05)> ]
Correction coefficient for
network entry in closed loop
when giving negative
corrections
Optional
0.7
0 to 1 dB in
steps of 0.05
[max-positivecorre
ction <(0 to 20
StepSize 0.1)> ]
Maximum positive power
correction (in dB) for network
entry in closed loop
Optional
0 to 20 in steps
of 0.1
[max-negativecorr
ection <(0 to 20
StepSize 0.1)> ]
Maximum negative power
correction (in dB) for network
entry in closed loop
Optional
0 to 20 in steps
of 0.1
bs power control configuration mode
Configuring the Power Control Closed Loop Correction Range
Parameters
To configure the Closed Loop Correction Range parameters, run the following
command:
4Motion
559
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
npu(config-bs-66053-pwrctrl)# clrange [lowthrshld-linear <(-20 to 0 StepSize
0.1)>] [lowthrshld-constant <(-20 to 0 StepSize 0.1)>] [highthrshld-linear <(0 to 20
StepSize 0.1)>] [highthrshld-constant <(0 to 20 StepSize 0.1)>]
IMPORTANT
When creating a new BS, at least one of the Power Control Closed Loop Correction Range
parameters must be configured explicitly (even if configured to the default value).
Command
Syntax
npu(config-bs-66053-pwrctrl)# clrange [lowthrshld-linear <(-20 to
0 StepSize 0.1)> ] [lowthrshld-constant <(-20 to 0 StepSize 0.1)>
] [highthrshld-linear <(0 to 20 StepSize 0.1)> ]
[highthrshld-constant <(0 to 20 StepSize 0.1)> ]
Privilege
Level
Syntax
Description
10
Parameter
Description
Presence
Default
Value
Possible
Values
[lowthrshld-linear
<(-20 to 0 StepSize
0.1)> ]
Closed loop correction range
threshold (in dB) below which
linear corrections are made.
Optional
-2
-20 to 0 in
steps of 0.1
Cannot be lower than
clrange-lowthrshld-constant
(see below)
lowthrshld-constan
t <(-20 to 0
StepSize 0.1)> ]
Closed loop correction range
threshold (in dB) below which
constant corrections are
made.
Optional
-8
-20 to 0 in
steps of 0.1
[highthrshld-linear
<(0 to 20 StepSize
0.1)> ]
Closed loop correction range
threshold (in dB) above which
linear corrections are made.
Optional
-20 to 0 in
steps of 0.1
[highthrshld-consta
nt <(0 to 20
StepSize 0.1)> ]
Closed loop correction range
threshold (in dB) above which
constant corrections are
made.
Optional
-20 to 0 in
steps of 0.1
Cannot be lower than
clrange-highthrshld-linear
(see above)
4Motion
560
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Modes
4.8.6.3
Managing BSs
bs power control configuration mode
Restoring Default Values for Power Control Configuration
Parameters
After enabling the Power Control configuration mode you can restore the default
values for parameters in the following parameters tables:
Noise and Interference Level (refer to Section 4.8.6.3.1)
Maximum EIRP (refer to Section 4.8.6.3.2)
Required C/N Level (refer to Section 4.8.6.3.3)
Open Loop Correction Policy (refer to Section 4.8.6.3.4)
Open Loop Correction Range (refer to Section 4.8.6.3.5)
Closed Loop - Unstable MS (refer to Section 4.8.6.3.6)
Closed Loop - MS in Network Entry (refer to Section 4.8.6.3.7)
Closed Loop Correction Range (refer to Section 4.8.6.3.8)
4.8.6.3.1
Restoring the Default Values of Power Control Target Noise and
Interference Level Parameters
To restore one or all of the Target Noise and Interference Level parameters to their
default values, run the following command:
npu(config-bs-66053-pwrctrl)# no nilevels [cqi-ack-ranging] [pusc]
You can restore only one parameter to its default values by specifying only that
parameter. For example, to restore only the pusc to the default value, run the
following command:
npu(config-bs-66053-pwrctrl)# no nilevels pusc
The parameter will be restored to its default value, while the other parameter will
remain unchanged.
To restore all Target Noise and Interference Level parameters to their default
value, run the following command:
npu(config-bs-66053-pwrctrl)# no nilevels
4Motion
561
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
NOTE
Refer to Section 4.8.6.2.1 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-pwrctrl)# no nilevels [cqi-ack-ranging ]
Privilege
Level
10
Command
Modes
bs power control configuration mode
4.8.6.3.2
[pusc]
Restoring the Default Values of the Power Control Maximum EIRP
Parameter
To restore the maxeirxp parameter to its default value, run the following
command:
npu(config-bs-66053-pwrctrl)# no maxeirxp
NOTE
Refer to Section 4.8.6.2.2 for a description and default value of this parameter.
Command
Syntax
npu(config-bs-66053-pwrctrl)# no maxeirxp
Privilege
Level
10
Command
Modes
bs power control configuration mode
4.8.6.3.3
Restoring the Default Values of Power Control Required C/N Level
Parameters
To restore some or all of the Required C/N Levels parameters to their default
values, run the following command:
4Motion
562
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
npu(config-bs-66053-pwrctrl)# no requiredcnr [ack] [cqi] [cdma] [qpsk-1by2]
[qpsk-3by4] [qam16-1by2] [qam16-3by4] [qam64-1by2] [qam64-2by3]
[qam64-3by4] [qam64-5by6]
You can restore only some parameters to their default values by specifying only
those parameter. For example, to restore only the ack and cqi parameters to the
default values, run the following command:
npu(config-bs-66053-pwrctrl)# no requiredcnr ack cqi
These parameters will be restored to their default value, while the other
parameters will remain unchanged.
To restore all Required C/N Levels parameters to their default value, run the
following command:
npu(config-bs-66053-pwrctrl)# no requiredcnr
NOTE
Refer to Section 4.8.6.2.3 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-pwrctrl)# no requiredcnr [ack ] [cqi ] [cdma ]
[qpsk-1by2 ] [qpsk-3by4 ] [qam16-1by2 ] [qam16-3by4 ] [qam64-1by2
] [qam64-2by3 ] [qam64-3by4 ] [qam64-5by6 ]
Privilege
Level
10
Command
Modes
bs power control configuration mode
4.8.6.3.4
Restoring the Default Values of Power Control Open Loop Correction
Policy Parameters
To restore some or all of the Open Loop Correction Policy parameters to their
default values, run the following command:
npu(config-bs-66053-pwrctrl)# no olpolicy [positivecoefficient]
[negativecoefficient] [max-positivecorrection] [max-negativecorrection]
You can restore only some parameters to their default values by specifying only
those parameters. For example, to restore only the positivecoefficient and
negativecoefficient parameters to the default values, run the following command:
4Motion
563
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
npu(config-bs-66053-pwrctrl)# no olpolicy positivecoefficient
negativecoefficient
These parameters will be restored to their default value, while the other
parameters will remain unchanged.
To restore all Open Loop Correction Policy parameters to their default value, run
the following command:
npu(config-bs-66053-pwrctrl)# no olpolicy
NOTE
Refer to Section 4.8.6.2.4 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-pwrctrl)# no olpolicy [positivecoefficient ]
[negativecoefficient ] [max-positivecorrection ]
[max-negativecorrection ]
Privilege
Level
10
Command
Modes
bs power control configuration mode
4.8.6.3.5
Restoring the Default Values of Power Control Open Loop Correction
Range Parameters
To restore some or all of the Open Loop Correction Range parameters to their
default values, run the following command:
npu(config-bs-66053-pwrctrl)# no olrange [lowthrshld-linear]
[lowthrshld-constant] [highthrshld-linear] [highthrshld-constant]
You can restore only some parameters to their default values by specifying only
those parameters. For example, to restore only the highthrshld-linear and
highthrshld-constant parameters to the default values, run the following
command:
npu(config-bs-66053-pwrctrl)# no olrange highthrshld-linear
highthrshld-constant
These parameters will be restored to their default value, while the other
parameters will remain unchanged.
4Motion
564
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
To restore all Open Loop Correction Range parameters to their default value, run
the following command:
npu(config-bs-66053-pwrctrl)# no olrange
NOTE
Refer to Section 4.8.6.2.5 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-pwrctrl)# no olrange [lowthrshld-linear ]
[lowthrshld-constant ] [highthrshld-linear ]
[highthrshld-constant ]
Privilege
Level
10
Command
Modes
bs power control configuration mode
4.8.6.3.6
Restoring the Default Values of Power Control Closed Loop - Unstable
MS Correction Policy Parameters
To restore some or all of the Open Loop - Unstable MS Correction Policy
parameters to their default values, run the following command:
npu(config-bs-66053-pwrctrl)# no clunstable [positivecoefficient]
[negativecoefficient] [max-positivecorrection] [max-negativecorrection]
You can restore only some parameters to their default values by specifying only
those parameters. For example, to restore only the positivecoefficient and
negativecoefficient parameters to the default values, run the following command:
npu(config-bs-66053-pwrctrl)# no clunstable positivecoefficient
negativecoefficient
These parameters will be restored to their default value, while the other
parameters will remain unchanged.
To restore all Open Loop - Unstable MS parameters to their default value, run the
following command:
npu(config-bs-66053-pwrctrl)# no clunstable
NOTE
Refer to Section 4.8.6.2.6 for a description and default values of these parameters.
4Motion
565
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Syntax
Managing BSs
npu(config-bs-66053-pwrctrl)# no clunstable [positivecoefficient ]
[negativecoefficient ] [max-positivecorrection ]
[max-negativecorrection ]
Privilege
Level
10
Command
Modes
bs power control configuration mode
4.8.6.3.7
Restoring the Default Values of Power Control Closed Loop - MS in
Network Entry Correction Policy Parameters
To restore some or all of the Open Loop - MS in Network Entry Correction Policy
parameters to their default values, run the following command:
npu(config-bs-66053-pwrctrl)# no clne [positivecoefficient] [negativecoefficient]
[max-positivecorrection] [max-negativecorrection]
You can restore only some parameters to their default values by specifying only
those parameters. For example, to restore only the positivecoefficient and
negativecoefficient parameters to the default values, run the following command:
npu(config-bs-66053-pwrctrl)# no clne positivecoefficient
negativecoefficient
These parameters will be restored to their default value, while the other
parameters will remain unchanged.
To restore all Open Loop - MS in Network Entry parameters to their default value,
run the following command:
npu(config-bs-66053-pwrctrl)# no clne
NOTE
Refer to Section 4.8.6.2.7 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-pwrctrl)# no clne [positivecoefficient ]
[negativecoefficient ] [max-positivecorrection ]
[max-negativecorrection ]
4Motion
566
System Manual
Chapter 4 - Operation and Administration Using the CLI
Privilege
Level
10
Command
Modes
bs power control configuration mode
4.8.6.3.8
Managing BSs
Restoring the Default Values of Power Control Closed Loop Correction
Range Parameters
To restore some or all of the Closed Loop Correction Range parameters to their
default values, run the following command:
npu(config-bs-66053-pwrctrl)# no clrange [lowthrshld-linear]
[lowthrshld-constant] [highthrshld-linear] [highthrshld-constant]
You can restore only some parameters to their default values by specifying only
those parameters. For example, to restore only the highthrshld-linear and
highthrshld-constant parameters to the default values, run the following
command:
npu(config-bs-66053-pwrctrl)# no clrange highthrshld-linear
highthrshld-constant
These parameters will be restored to their default value, while the other
parameters will remain unchanged.
To restore all Closed Loop Correction Range parameters to their default value, run
the following command:
npu(config-bs-66053-pwrctrl)# no clrange
NOTE
Refer to Section 4.8.6.2.8 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-pwrctrl)# no clrange [lowthrshld-linear ]
[lowthrshld-constant ] [highthrshld-linear ]
[highthrshld-constant ]
Privilege
Level
10
Command
Modes
bs power control configuration mode
4Motion
567
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.6.4
Managing BSs
Terminating the Power Control Configuration Mode
Run the following command to terminate the Power Control configuration mode:
npu(config-bs-66053-pwrctrl)# exit
IMPORTANT
Do not forget to execute the apply command before terminating the Power Control configuration
mode: npu(config-bs-66053-pwrctrl)# apply
Command
Syntax
npu(config-bs-66053-pwrctrl)# exit
Privilege
Level
10
Command
Modes
bs power control configuration mode
4.8.6.5
Displaying Configuration Information for Power Control
Parameters
You can display the current configuration information for the following
parameters tables:
Noise and Interference Level (refer to Section 4.8.6.5.1)
Maximum EIRP (refer to Section 4.8.6.5.2)
Required C/N Level (refer to Section 4.8.6.5.3)
Open Loop Correction Policy (refer to Section 4.8.6.5.4)
Open Loop Correction Range (refer to Section 4.8.6.5.5)
Closed Loop - Unstable MS (refer to Section 4.8.6.5.6)
Closed Loop - MS in Network Entry (refer to Section 4.8.6.5.7)
Closed Loop Correction Range (refer to Section 4.8.6.5.8)
All (refer to Section 4.8.6.5.9)
4Motion
568
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.6.5.1
Managing BSs
Displaying Configuration Information for Power Control Target Noise
and Interference Level Parameters
To display configuration for the Power Control Target Noise and Interference Level
parameters, run the following command:
npu# show pwrctrl-nilevels bs [<(1 to 16777215 StepSize 1)
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Power Control Target Noise and Interference Level
parameters of BS 66053, run the following command:
npu# show pwrctrl-nilevels bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show pwrctrl-nilevels bs
Command
Syntax
npu# show pwrctrl-nilevels bs [<(1 to 16777215 StepSize 1)
Privilege
Level
Syntax
Description
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the Target Noise and
Interference Level
parameters of a specific BS.
Do not specify a value for this
parameter if you want to
display the Target Noise and
Interference Level
parameters of all BSs.
569
System Manual
Chapter 4 - Operation and Administration Using the CLI
Display
Format
(for each
existing BS
if requested
for all BSs)
Command
Modes
4.8.6.5.2
Managing BSs
BSIDLSB
:
NoiseandInterferenceLevelforCQI&ACKRegion
:
NoiseandInterferenceLevelforPUSCZone
:
Global command mode
Displaying Configuration Information for Power Control Maximum
EIRP
To display configuration for the Power Control Maximum EIRP parameter, run the
following command:
npu# show pwrctrl-maxeirxp bs [<(1 to 16777215 StepSize 1)
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Power Control Maximum EIRP parameter of BS 66053,
run the following command:
npu# show pwrctrl-maxeirxp bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show pwrctrl-maxeirxp bs
Command
Syntax
npu# show pwrctrl-maxeirxp bs [<(1 to 16777215 StepSize 1)
Privilege
Level
4Motion
570
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Display
Format
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the Maximum EIRP
parameter of a specific BS.
Do not specify a value for this
parameter if you want to
display the Maximum EIRP
parameter of all BSs.
BSIDLSB
:
MaxEIRxP
:
(for each
existing BS
if requested
for all BSs)
Command
Modes
4.8.6.5.3
Global command mode
Displaying Configuration Information for Power Control Required C/N
Level Parameters
To display configuration for the Power Control Required C/N Level parameters,
run the following command:
npu# show pwrctrl-requiredcnr bs [<(1 to 16777215 StepSize 1)
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Power Control Required C/N Level parameters of BS
66053, run the following command:
npu# show pwrctrl-requiredcnr bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show pwrctrl-requiredcnr bs
4Motion
571
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Command
Syntax
npu# show pwrctrl-requiredcnr bs [<(1 to 16777215 StepSize 1)
Privilege
Level
Syntax
Description
Display
Format
(for each
existing BS
if requested
for all BSs)
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the Required C/N
Level parameters of a specific
BS. Do not specify a value for
this parameter if you want to
display the Required C/N
Level parameters of all BSs.
BSIDLSB
:
RequiredCNRforACK
:
RequiredCNRforCQI
:
RequiredCNRforCDMA
:
RequiredCNRforQPSK1/2
:
RequiredCNRforQPSK3/4
Command
Modes
4Motion
:
RequiredCNRfor16QAM1/2
:
RequiredCNRfor16QAM3/4
:
RequiredCNRfor64QAM1/2
:
RequiredCNRfor64QAM2/3
:
RequiredCNRfor64QAM3/4
:
RequiredCNRfor64QAM5/6
:
Global command mode
572
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.6.5.4
Managing BSs
Displaying Configuration Information for Power Control Open Loop
Correction Policy Parameters
To display configuration for the Power Control Open Loop Correction Policy
parameters, run the following command:
npu# show pwrctrl-olpolicy bs [<(1 to 16777215 StepSize 1)
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Power Control Open Loop Correction Policy parameters of
BS 66053, run the following command:
npu# show pwrctrl-olpolicy bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show pwrctrl-olpolicy bs
Command
Syntax
npu# show pwrctrl-olpolicy bs [<(1 to 16777215 StepSize 1)
Privilege
Level
Syntax
Description
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the Open Loop
Correction Policy parameters
of a specific BS. Do not
specify a value for this
parameter if you want to
display the Open Loop
Correction Policy parameters
of all BSs.
573
System Manual
Chapter 4 - Operation and Administration Using the CLI
Display
Format
(for each
existing BS
if requested
for all BSs)
Command
Modes
4.8.6.5.5
Managing BSs
BSIDLSB
:
OpenLoopPositiveCorrectionCoefficient
:
OpenLoopNegativeCorrectionCoefficient
:
OpenLoopMaximumPositivePowerCorrection(dB)
:
OpenLoopMaximumNegativePowerCorrection(dB)
:
Global command mode
Displaying Configuration Information for Power Control Open Loop
Correction Range Parameters
To display configuration for the Power Control Open Loop Correction Range
parameters, run the following command:
npu# show pwrctrl-olrange bs [<(1 to 16777215 StepSize 1)
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Power Control Open Loop Correction Range parameters of
BS 66053, run the following command:
npu# show pwrctrl-olrange bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show pwrctrl-olrange bs
Command
Syntax
npu# show pwrctrl-olrange bs [<(1 to 16777215 StepSize 1)
Privilege
Level
4Motion
574
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Display
Format
(for each
existing BS
if requested
for all BSs)
Command
Modes
4.8.6.5.6
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the Open Loop
Correction Range parameters
of a specific BS. Do not
specify a value for this
parameter if you want to
display the Open Loop
Correction Range parameters
of all BSs.
BSIDLSB
:
OpenLoopLowerThresholdforLinearCorrection(dB)
:
OpenLoopLowerThresholdforConstantCorrection(dB)
:
OpenLoopHigherThresholdforLinearCorrection(dB)
:
OpenLoopHigherThresholdforConstantCorrection(dB)
:
Global command mode
Displaying Configuration Information for Power Control Closed Loop Unstable MS Correction Policy Parameters
To display configuration for the Power Control Closed Loop - Unstable MS
Correction Policy parameters, run the following command:
npu# show pwrctrl-clunstable bs [<(1 to 16777215 StepSize 1)
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Power Control Closed Loop - Unstable MS parameters of
BS 66053, run the following command:
npu# show pwrctrl-clunstable bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show pwrctrl-clunstable bs
4Motion
575
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Command
Syntax
npu# show pwrctrl-clunstable bs [<(1 to 16777215 StepSize 1)
Privilege
Level
Syntax
Description
Display
Format
(for each
existing BS
if requested
for all BSs)
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the Closed Loop Unstable MS parameters of a
specific BS. Do not specify a
value for this parameter if you
want to display the Closed
Loop - Unstable MS
parameters of all BSs.
BSIDLSB
:
ClosedLoopUnstableMSPositiveCorrectionCoefficient :
ClosedLoopUnstableMSNegativeCorrectionCoefficient :
ClosedLoopUnstableMSMaximumPositivePowerCorrection(dB):
ClosedLoopUnstableMSMaximumNegativePowerCorrection(dB):
Command
Modes
4.8.6.5.7
Global command mode
Displaying Configuration Information for Power Control Closed Loop MS in Network Entry Correction Policy Parameters
To display configuration for the Power Control Closed Loop - MS in Network Entry
Correction Policy parameters, run the following command:
npu# show pwrctrl-clne bs [<(1 to 16777215 StepSize 1)
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Power Control Closed Loop - MS in Network Entry
parameters of BS 66053, run the following command:
4Motion
576
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
npu# show pwrctrl-clne bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show pwrctrl-clne bs
Command
Syntax
npu# show pwrctrl-clne bs [<(1 to 16777215 StepSize 1)
Privilege
Level
Syntax
Description
Display
Format
(for each
existing BS
if requested
for all BSs)
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the Closed Loop - MS
in Network Entry parameters
of a specific BS. Do not
specify a value for this
parameter if you want to
display the Closed Loop - MS
in Network Entry parameters
of all BSs.
BSIDLSB
:
ClosedLoopNetworkEntryPositiveCorrectionCoefficient:
ClosedLoopNetworkEntryNegativeCorrectionCoefficient:
ClosedLoopNetworkEntryMaximumPositivePowerCorrection(dB):
ClosedLoopNetworkEntryMaximumNegativePowerCorrection(dB):
Command
Modes
4Motion
Global command mode
577
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.6.5.8
Managing BSs
Displaying Configuration Information for Power Control Closed Loop
Correction Range Parameters
To display configuration for the Power Control Closed Loop Correction Range
parameters, run the following command:
npu# show pwrctrl-clrange bs [<(1 to 16777215 StepSize 1)
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Power Control Closed Loop Correction Range parameters
of BS 66053, run the following command:
npu# show pwrctrl-clrange bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show pwrctrl-clrange bs
Command
Syntax
npu# show pwrctrl-clrange bs [<(1 to 16777215 StepSize 1)
Privilege
Level
Syntax
Description
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the Closed Loop
Correction Range parameters
of a specific BS. Do not
specify a value for this
parameter if you want to
display the Closed Loop
Correction Range parameters
of all BSs.
578
System Manual
Chapter 4 - Operation and Administration Using the CLI
Display
Format
(for each
existing BS
if requested
for all BSs)
Managing BSs
BSIDLSB
:
ClosedLoopLowerThresholdforLinearCorrection(dB)
:
ClosedLoopLowerThresholdforConstantCorrection(dB) :
ClosedLoopHigherThresholdforLinearCorrection(dB)
:
ClosedLoopHigherThresholdforConstantCorrection(dB):
Command
Modes
4.8.6.5.9
Global command mode
Displaying Configuration Information for All Power Control
Parameters
To display configuration for all Power Control parameters, run the following
command:
npu# show pwrctrl-all bs [<(1 to 16777215 StepSize 1)
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display all Power Control parameters of BS 66053, run the following
command:
npu# show pwrctrl-all bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show pwrctrl-all bs
Command
Syntax
npu# show pwrctrl-all bs [<(1 to 16777215 StepSize 1)
Privilege
Level
10
4Motion
579
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Command
Modes
4.8.7
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display all Power Control
parameters of a specific BS.
Do not specify a value for this
parameter if you want to
display all Power Control
parameters of all BSs.
Global command mode
Managing BS Feedback Allocation
Parameters
After enabling the BS configuration mode, you can execute the following tasks:
Configure one or more of the Feedback Allocation parameters (refer to
Section 4.8.7.1).
Restore the default values of one or all of the Feedback Allocation parameters
(refer to Section 4.8.7.2).
You can display configuration information for the Feedback Allocation parameters
of a selected or all existing BSs (refer to Section 4.8.7.3).
4.8.7.1
Configuring Feedback Allocation Parameters
To configure the Feedback Allocation Parameters:
From the BS configuration mode, run the following command:
npu(config-bs-66053)# feedbackalloc [pr-cdma <(0 to 12000 StepSize
1)> ] [ir-cdma <(0 to 12000 StepSize 1)> ] [max-cqi <(0 to 29
StepSize 1)> ] [ert-poll-enable {true | false} ]
4Motion
580
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
IMPORTANT
When creating a new BS, the mandatory max-cqi parameter must be configured. Typically it should
be configured to 7 for bandwidth=5MHz and 19 for bandwidth=7 or 10 MHz.
Command
Syntax
npu(config-bs-66053)# feedbackalloc [pr-cdma <(0 to 12000 StepSize
1)> ] [ir-cdma <(0 to 12000 StepSize 1)> ] [max-cqi <(0 to 29
StepSize 1)> ] [ert-poll-enable {true | false} ]
Privilege
Level
10
Syntax
Description
Parameter
Description
Presence
Default
Value
Possible
Values
[pr-cdma <(0 to
12000 StepSize 1)> ]
The period of PR CDMA
allocations, in frames.
Optional
0 - 12000
Cannot be higher than
ir-cdma (see below)
[ir-cdma <(0 to
12000 StepSize 1)> ]
The period of IR CDMA
allocations, in frames
Optional
20
0 - 12000
[max-cqi <(0 to 29
StepSize 1)> ]
The maximum size
allowed for the CQI
region, in subchannels.
Mandatory
when
creating a
new BS.
N/A*
0-11 for
Optional
true
[ert-poll-enable {true
| false} ]
Command
Modes
Defines the BS's behavior
(whether polling is
enabled or not) upon
reception of zero size BW
requests.
bw=5MHz
0-29 for
bw=7 or
10 MHz
true
False
bs configuration mode
* The default value for the mandatory max-cqi parameter is be 7 for bw=5MHz and
19 for bw=7 or 10 MHz.
4Motion
581
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.7.2
Managing BSs
Restoring the Default Values of Feedback Allocation
Parameters
To restore one or all of the Feedback Allocation non-mandatory parameters to
their default values, run the following command:
npu(config-bs-66053)# no feedbackalloc [pr-cdma] [ir-cdma] [ert-poll-enable]
You can restore only some parameters to their default values by specifying only
those parameters. For example, to restore only the pr-cdma and ir-cdma
parameters to the default values, run the following command:
npu(config-bs-66053)# no feedbackalloc pr-cdma ir-cdma
These parameters will be restored to their default value, while the other
parameters will remain unchanged.
To restore all Feedback Allocation non-mandatory parameters to their default
value, run the following command:
npu(config-bs-66053)# no feedbackalloc
NOTE
Refer to Section 4.8.7.1 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053)# no feedbackalloc [pr-cdma ] [ir-cdma ]
[ert-poll-enable]
Privilege
Level
10
Command
Modes
bs configuration mode
4.8.7.3
Displaying Configuration Information for Feedback
Allocation Parameters
To display configuration information for Feedback Allocation parameters, run the
following command:
npu# show feedbackalloc bs [<(1 to 16777215 StepSize 1)
4Motion
582
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Feedback Allocation parameters of BS 66053, run the
following command:
npu# show feedbackalloc bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show feedbackalloc bs
Command
Syntax
npu# show feedbackalloc bs [<(1 to 16777215 StepSize 1)
Privilege
Level
Syntax
Description
Display
Format
(for each
existing BS
if requested
for all BSs)
Command
Modes
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display Feedback Allocation
parameters of a specific BS.
Do not specify a value for this
parameter if you want to
display Feedback Allocation
parameters of all BSs.
BSIDLSB
:
PRCDMAAllocationsPeriod(frames)
:
IRCDMAAllocationsPeriod(frames)
:
MaximumCQIRegionSize(subchannels)
:
Global command mode
583
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.8
Managing BSs
Managing Neighbor Advertisement
Parameters
After enabling the BS configuration mode, you can execute the following tasks:
Configure one or more of the Neighbor Advertisement parameters (refer to
Section 4.8.8.1).
Restore the default values of one or all of the Neighbor Advertisement
parameters (refer to Section 4.8.8.2).
You can display configuration information for the Neighbor Advertisement
parameters of a selected or all existing BSs (refer to Section 4.8.8.3).
4.8.8.1
Configuring Neighbor Advertisement Parameters
To configure the Neighbor Advertisement Parameters:
From the BS configuration mode, run the following command:
npu(config-bs-66053)# nbradvertise [mininterval-normalload <(0 to 100
StepSize 0.1)>] [mininterval-highload <(0 to 100 StepSize 0.1)>] [triggersetup <(0
to 100 StepSize 0.1)>]
IMPORTANT
When creating a new BS, at least one of the Neighbour Advertisement parameters must be
configured explicitly (even if configured to the default value).
Command
Syntax
npu(config-bs-66053)# nbradvertise [mininterval-normalload <(0 to
100 StepSize 0.1)> ] [mininterval-highload <(0 to 100 StepSize
0.1)> ] [triggersetup <(0 to 100 StepSize 0.1)> ]
Privilege
Level
10
Syntax
Description
4Motion
Parameter
Description
584
Presence
Default
Value
Possible
Values
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Modes
4.8.8.2
Managing BSs
[mininterval-normalload
<(0 to 100 StepSize
0.1)> ]
The minimum interval (in
seconds) between
NBRADV transmissions in
normal load state.
Optional
0.5
0 -100 in
steps of 0.1
[mininterval-highload
<(0 to 100 StepSize
0.1)> ]
The minimum interval (in
seconds) between
NBRADV transmissions in
high load state.
Optional
0 -100 in
steps of 0.1
[triggersetup <(0 to 100
StepSize 0.1)> ]
The periodic NBRADV
transmission interval, in
seconds
Optional
10
0 - 100 in
steps of 0.1
bs configuration mode
Restoring the Default Values of Neighbor Advertisement
Parameters
To restore one or all of the Neighbor Advertisement parameters to their default
values, run the following command:
npu(config-bs-66053)# no nbradvertise [mininterval-normalload]
[mininterval-highload] [triggersetup]
You can restore only some parameters to their default values by specifying only
those parameters. For example, to restore only the mininterval-normalload
parameters to the default values, run the following command:
npu(config-bs-66053)# no nbradvertise mininterval-normalload
This parameter will be restored to its default value, while the other parameters
will remain unchanged.
To restore all Neighbor Advertisement parameters to their default value, run the
following command:
npu(config-bs-66053)# no nbradvertise
NOTE
Refer to Section 4.8.8.1 for a description and default values of these parameters.
Command
Syntax
4Motion
npu(config-bs-66053)# no nbradvertise [mininterval-normalload]
[mininterval-highload] [triggersetup]
585
System Manual
Chapter 4 - Operation and Administration Using the CLI
Privilege
Level
10
Command
Modes
bs configuration mode
4.8.8.3
Managing BSs
Displaying Configuration Information for Neighbor
Advertisement Parameters
To display configuration information for Neighbor Advertisement parameters, run
the following command:
npu# show nbradvertise bs [<(1 to 16777215 StepSize 1)
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Neighbor Advertisement parameters of BS 66053, run the
following command:
npu# show nbradvertise bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show nbradvertise bs
Command
Syntax
npu# show nbradvertise bs [<(1 to 16777215 StepSize 1)
Privilege
Level
4Motion
586
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Display
Format
(for each
existing BS
if requested
for all BSs)
Command
Modes
4.8.9
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display Neighbour
Advertisement parameters of
a specific BS. Do not specify
a value for this parameter if
you want to display
Neighbour Advertisement
parameters of all BSs.
BSIDLSB
:
MinimumInterval-NormalLoad
:
MinimumInterval-HighLoad
:
PeriodicInterval
:
Global command mode
Managing Triggers Parameters
After enabling the BS configuration mode, you can configure one or more of the
Triggers parameters (refer to Section 4.8.9.1).
You can display configuration information for the Triggers parameters of a
selected or all existing BSs (refer to Section 4.8.9.2).
4.8.9.1
Configuring Triggers Parameters
To configure the Triggers Parameters:
From the BS configuration mode, run the following command:
npu(config-bs-66053)# triggers-
Each Trigger is configured separately. This is the general structure of the
command.
4Motion
587
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
IMPORTANT
When creating a new BS, at least one of the Triggers parameters must be configured explicitly.
Command
Syntax
npu(config-bs-66053)# triggers-
Privilege
Level
10
Syntax
Description
Parameter
Description
Presence
Default
Value
Possible
Values
The Trigger name.
Mandatory
N/A
See
Table 4-3
0 below
Command
Modes
Defines the threshold
value for the Trigger.
Mandatory
N/A
See
Table 4-3
0 below
bs configuration mode
Table 4-30: Trigger Names and Possible Value Ranges
Trigger Name
Trigger Condition
Action
Possible Values
triggers-scnreq-cinr-min
The C/N at the Serving BS is
below the Trigger threshold
(in dB)
Scan Request
-64 to 63.5 in steps of 0.5
triggers-scnreq-rssi-min
The RSSI at the Serving BS
is below the Trigger
thresholdd (in Bm)
-103.75 to -40 in steps of 0.25
triggers-scnreq-rtd-max
The Serving BS distance from
the MS (calculated by
measuring the round trip
delay) is above the Trigger
threshold (in meter)
0-3400 in steps of 50 if BS BW
is 10 MHz, 0-6800 in steps of
50 if BS BW is 5 MHz, 0-4800
in steps of 50 if BS BW is 7
MHz
4Motion
588
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Table 4-30: Trigger Names and Possible Value Ranges
Trigger Name
Trigger Condition
Action
Possible Values
triggers-horeq-cinr-margin
The C/N at the Neighbour BS
minus the C/N at the Serving
BS is above the Trigger
threshold (in dB)
Handover
Request
-64 to 63.5 in steps of 0.5
triggers-horeq-cinr-max
The C/N at the Neighbour BS
is above the Trigger threshold
(in dB)
-64 to 63.5 in steps of 0.5
triggers-horeq-cinr-min
The C/N at the Serving BS is
below the Trigger threshold
(in dB)
-64 to 63.5 in steps of 0.5
triggers-horeq-rssi-margin
The RSSI at the Neighbour
BS minus the RSSI at the
Serving BS is above the
Trigger threshold (in dBm)
-32 to 31.75 in steps of 0.25
triggers-horeq-rssi-max
The RSSI at the Neighbour
BS is above the Trigger
threshold (in dBm)
-103.75 to -40 in steps of 0.25
triggers-horeq-rssi-min
The RSSI at the Serving BS is
below the Trigger threshold
(in dBm)
-103.75 to -40 in steps of 0.25
triggers-horeq-rtd-max
The Serving BS distance from
the MS (calculated by
measuring the round trip
delay) is above the Trigger
threshold (in meter)
0-3400 in steps of 50 if BS BW
is 10 MHz, 0-6800 in steps of
50 if BS BW is 5 MHz, 0-4800
in steps of 50 if BS BW is 7
MHz
4.8.9.2
Displaying Configuration Information for Triggers
Parameters
To display configuration information for Triggers parameters, run the following
command:
npu# show triggers bs [<(1 to 16777215 StepSize 1)> TrigName {scnReqCinrMin
| scnReqRssiMin | scnReqRtdMax | hoReqCinrMaxNbs | hoReqRssiMaxNbs |
hoReqCinrMargin | hoReqRssiMargin | hoReqRtdMax | hoReqCinrMinSbs |
hoReqRssiMinSbs}]
Specify the BS ID and Trigger name if you want to display configuration for a
particular Trigger. For example, to display the scnReqCinrMin parameters of BS
66053, run the following command:
npu# show triggers bs 66053 TrigName scnReqCinrMin
4Motion
589
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Do not specify these parameters if you want to view configuration information for
all existing BSs. To display information for all BSs, run the following command:
npu# show triggers bs
Command
Syntax
npu# show triggers bs [<(1 to 16777215 StepSize 1)> TrigName {scnReqCinrMin |
Privilege
Level
Syntax
Description
scnReqRssiMin | scnReqRtdMax | hoReqCinrMaxNbs | hoReqRssiMaxNbs | hoReqCinrMargin |
hoReqRssiMargin | hoReqRtdMax | hoReqCinrMinSbs | hoReqRssiMinSbs} ]
Parameter
Description
Presence
Default
Value
Possible Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
TrigName
{scnReqCinrMin |
scnReqRssiMin |
scnReqRtdMax |
hoReqCinrMaxNbs |
hoReqRssiMaxNbs |
hoReqCinrMargin |
hoReqRssiMargin |
hoReqRtdMax |
hoReqCinrMinSbs |
hoReqRssiMinSbs} ]
The Trigger name
scnReqCinrMin
Specify only if you
want to display a
specific Trigger of a
specific BS. Do not
specify if you want to
display all Triggers
parameters of all BSs
scnReqRssiMin
Specify a value for
this parameter if you
want to display a
specific Trigger of a
specific BS. Do not
specify a value for
this parameter if you
want to display all
Triggers parameters
of all BSs.
scnReqRtdMax
hoReqCinrMaxNbs
hoReqRssiMaxNbs
hoReqCinrMargin
hoReqRssiMargin
hoReqRtdMax
hoReqCinrMinSbs
hoReqRssiMinSbs}
4Motion
590
System Manual
Chapter 4 - Operation and Administration Using the CLI
Display
Format
Managing BSs
BSIDLSB
:
scnReqRssiMin
:
(for a
selected
Trigger)
Command
Modes
Global command mode
4.8.10 Managing Trigger Setup Parameters
After enabling the BS configuration mode, you can execute the following tasks:
Configure one or more of the Trigger Setup parameters (refer to
Section 4.8.10.1).
Restore the default values of one or all of the Trigger Setup parameters (refer to
Section 4.8.10.2).
You can display configuration information for the Trigger Setup parameters of a
selected or all existing BSs (refer to Section 4.8.10.3).
4.8.10.1
Configuring Trigger Setup Parameters
To configure the Trigger Setup Parameters:
From the BS configuration mode, run the following command:
npu(config-bs-66053)# triggersetup [hysteresismargin <(0 to 255 StepSize 1)>]
[timetotrigger <(0 to 255 StepSize 1)>] [avgduration-rssi <(0 to 255 StepSize 1)>]
[avgduration-cinr <(0 to 255 StepSize 1)>] [avgduration-rtd <(0 to 255 StepSize
1)>]
IMPORTANT
When creating a new BS, at least one of the Trigger Setup parameters must be configured explicitly
(even if configured to the default value).
4Motion
591
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Command
Syntax
npu(config-bs-66053)# triggersetup [hysteresismargin <(0 to 255
StepSize 1)> ] [timetotrigger <(0 to 255 StepSize 1)> ]
[avgduration-rssi <(0 to 255 StepSize 1)> ] [avgduration-cinr <(0
to 255 StepSize 1)> ] [avgduration-rtd <(0 to 255 StepSize 1)> ]
Privilege
Level
10
Syntax
Description
Command
Modes
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
[hysteresismargin <(0
to 255 StepSize 1)> ]
The CINR hysteresis in dB
for adding or deleting
neighbors. The hysteresis
margin is used by the MS
in the decision whether to
include a neighbor BS in a
list of possible target BSs.
Optional
0 - 255
[timetotrigger <(0 to
255 StepSize 1)> ]
The minimum time in
milliseconds between
adding or deleting a
neighbor. It is the time
that the MS takes to
decide whether to select a
neighbor BS as a possible
target BS and is
applicable only for HHO.
Optional
50
0 - 255
[avgduration-rssi <(0
to 255 StepSize 1)> ]
The default RSSI average
duration for triggers, in
milliseconds
Optional
50
0 - 255
[avgduration-cinr <(0
to 255 StepSize 1)> ]
The default CINR average
duration for triggers, in
milliseconds
Optional
50
0 - 255
[avgduration-rtd <(0 to
255 StepSize 1)> ]
The default RTD average
duration for triggers, in
milliseconds
Optional
50
0 - 255
bs configuration mode
592
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.10.2
Managing BSs
Restoring the Default Values of Trigger Setup Parameters
To restore one or all of the Trigger Setup parameters to their default values, run
the following command:
npu(config-bs-66053)# no triggersetup [hysteresismargin] [timetotrigger]
[avgduration-rssi] [avgduration-cinr] [avgduration-rtd]
You can restore only some parameters to their default values by specifying only
those parameters. For example, to restore only the hysteresismargin parameter to
the default value, run the following command:
npu(config-bs-66053)# no triggersetup hysteresismargin
This parameter will be restored to its default value, while the other parameters
will remain unchanged.
To restore all Trigger Setup parameters to their default value, run the following
command:
npu(config-bs-66053)# no triggersetup
NOTE
Refer to Section 4.8.10.1 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053)# no triggersetup [hysteresismargin ]
[timetotrigger ] [avgduration-rssi] [avgduration-cinr]
[avgduration-rtd ]
Privilege
Level
10
Command
Modes
bs configuration mode
4.8.10.3
Displaying Configuration Information for Trigger Setup
Parameters
To display configuration information for Trigger Setup parameters, run the
following command:
npu# show triggersetup bs [<(1 to 16777215 StepSize 1)
4Motion
593
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Trigger Setup parameters of BS 66053, run the following
command:
npu# show triggersetup bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show triggersetup bs
Command
Syntax
npu# show triggersetup bs [<(1 to 16777215 StepSize 1)
Privilege
Level
Syntax
Description
Display
Format
(for each
existing BS
if requested
for all BSs)
Command
Modes
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display Trigger Setup
parameters of a specific BS.
Do not specify a value for this
parameter if you want to
display Trigger Setup
parameters of all BSs.
BSIDLSB
:
HysteresisMargin(dB)
:
TimetoTrigger(msec)
:
AverageDurationofDefaultRSSI(msec)
:
AverageDurationofDefaultCINR(msec)
:
AverageDurationofDefaultRTD(msec)
:
Global command mode
594
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
4.8.11 Managing Scan Negotiation Parameters
After enabling the BS configuration mode, you can execute the following tasks:
Configure one or more of the Scan Negotiation parameters (refer to
Section 4.8.11.1).
Restore the default values of some or all of the Scan Negotiation parameters
(refer to Section 4.8.11.2).
You can display configuration information for the Scan Negotiation parameters of
a selected or all existing BSs (refer to Section 4.8.11.3).
4.8.11.1
Configuring Scan Negotiation Parameters
To configure the Scan Negotiation Parameters:
From the BS configuration mode, run the following command:
npu(config-bs-66053)# scanning [max-attempts <(0 to 255 StepSize 1)>] [interval
<(0 to 100 StepSize 0.1)>] [enable-autoaccept {TRUE | FALSE}] [enable-modify
{TRUE | FALSE}] [min-interval <(2 to 255 StepSize 1)>] [max-duration <(0 to 255
StepSize 1)>] [min-degradationfactor <(0 to 1 StepSize 0.1)>] [honegotiation-sbs
<(0 to 255 StepSize 1)>]
IMPORTANT
When creating a new BS, at least one of the Scan Negotiation parameters must be configured
explicitly (even if configured to the default value).
Command
Syntax
npu(config-bs-66053)# scanning [max-attempts <(0 to 255 StepSize
1)> ] [interval <(0 to 100 StepSize 0.1)> ] [enable-autoaccept
{TRUE | FALSE} ] [enable-modify {TRUE | FALSE} ] [min-interval <(2
to 255 StepSize 1)> ] [max-duration <(0 to 255 StepSize 1)> ]
[min-degradationfactor <(0 to 1 StepSize 0.1)> ]
[honegotiation-sbs <(0 to 255 StepSize 1)> ]
Privilege
Level
10
4Motion
595
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
[max-attempts <(0 to
255 StepSize 1)> ]
The maximum allowed
number of consecutive
MOB_SCN-REQs .
Optional
10
0 - 255
[interval <(0 to 100
StepSize 0.1)> ]
The measuring interval for
counting
MOB_SCN-REQs abuse.
Optional
0 to 100
secs in
steps of 0.1
[enable-autoaccept
{TRUE | FALSE} ]
Determine whether all
scan profiles requested by
MSs will be accepted
automatically.
Optional
TRUE
TRUE
FALSE
Note: If TRUE all scan
request will be
automatically accepted.
[enable-modify {TRUE
| FALSE} ]
Determines whether the
BS will modify unfeasible
scan profiles requested by
MSs.
Optional
TRUE
TRUE
FALSE
Note: If TRUE the BS will
modify unfeasible scan
profile requests and if
FALSE the BS will deny
the requests.
Command
Modes
4Motion
[min-interval <(2 to
255 StepSize 1)> ]
The minimum interleaving
interval permitted to the
MS in the scan profile (in
frames)
Optional
0 - 255
[max-duration <(0 to
255 StepSize 1)> ]
The maximum duration of
a scan permitted to the
MS in the scan profile (in
frames).
Optional
255
0 - 255
[min-degradationfacto
r <(0 to 1 StepSize
0.1)> ]
The minimum bandwidth
degradation factor allowed
in the scan profile
Optional
0 to 1 in
steps of 0.1
[honegotiation-sbs
<(0 to 255 StepSize
1)> ]
The minimum value (in
frames) for the start frame
in the scan profile.
Optional
0 - 255
bs configuration mode
596
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.11.2
Managing BSs
Restoring the Default Values of Scan Negotiation
Parameters
To restore some or all of the Scan Negotiation parameters to their default values,
run the following command:
npu(config-bs-66053)# no scanning [max-attempts] [interval]
[enable-autoaccept] [enable-modify][min-interval] [max-duration]
[min-degradationfactor] [honegotiation-sbs]
You can restore only some parameters to their default values by specifying only
those parameters. For example, to restore only the max-attempts parameter to the
default value, run the following command:
npu(config-bs-66053)# no scanning max-attempts
This parameter will be restored to its default value, while the other parameters
will remain unchanged.
To restore all Scan Negotiation parameters to their default value, run the following
command:
npu(config-bs-66053)# no scanning
NOTE
Refer to Section 4.8.11.1 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053)# no scanning [max-attempts ] [interval ]
[enable-autoaccept ] [enable-modify ][min-interval ] [max-duration
] [min-degradationfactor ] [honegotiation-sbs ]
Privilege
Level
10
Command
Modes
bs configuration mode
4.8.11.3
Displaying Configuration Information for Scan Negotiation
Parameters
To display configuration information for Scan Negotiation parameters, run the
following command:
npu# show scanning bs [<(1 to 16777215 StepSize 1)
4Motion
597
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Scan Negotiation parameters of BS 66053, run the
following command:
npu# show scanning bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show scanning bs
Command
Syntax
npu# show scanning bs [<(1 to 16777215 StepSize 1)
Privilege
Level
Syntax
Description
Display
Format
(for each
existing BS
if requested
for all BSs)
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display Scan Negotiation
parameters of a specific BS.
Do not specify a value for this
parameter if you want to
display Scan Negotiation
parameters of all BSs.
BSIDLSB
:
MaximumAttempts
:
MeasuringInterval(sec)
:
EnableAutoAcceptProfile
:
EnableModifyProfile
:
MinimumInterleavingInterval(frames)
:
MaximumScanDuration(frames)
:
MinimumBandwidthDegradationFactor
:
MinimumStartFrame(frames)
:
598
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Modes
Managing BSs
Global command mode
4.8.12 Managing Handover Negotiation at SBS
Parameters
After enabling the BS configuration mode, you can execute the following tasks:
Configure one or more of the Handover Negotiation at SBS parameters (refer to
Section 4.8.12.1).
Restore the default values of some or all of the Handover Negotiation at SBS
parameters (refer to Section 4.8.12.2).
You can display configuration information for the Handover Negotiation at SBS
parameters of a selected or all existing BSs (refer to Section 4.8.12.3).
4.8.12.1
Configuring Handover Negotiation at SBS Parameters
To configure the Handover Negotiation at SBS Parameters:
From the BS configuration mode, run the following command:
npu(config-bs-66053)# honegotiation-sbs [selectcoefficient <(0 to 10 StepSize
0.1)>] [max-tbs <(0 to 255 StepSize 1)>] [min-actiontime <(0 to 255 StepSize 1)>]
[max-actiontime <(0 to 255 StepSize 1)>]
IMPORTANT
When creating a new BS, at least one of the Handover Negotiation at SBS parameters must be
configured explicitly (even if configured to the default value).
Command
Syntax
npu(config-bs-66053)# honegotiation-sbs [selectcoefficient <(0 to
10 StepSize 0.1)> ] [max-tbs <(0 to 255 StepSize 1)> ]
[min-actiontime <(0 to 255 StepSize 1)> ] [max-actiontime <(0 to
255 StepSize 1)> ]
Privilege
Level
10
4Motion
599
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Command
Modes
4.8.12.2
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
[selectcoefficient <(0
to 10 StepSize 0.1)> ]
The coefficient for
selection of Target BSs for
MOB_BSHO-RSP
Optional
0.3
0 to 10 in
steps of 0.1
[max-tbs <(0 to 255
StepSize 1)> ]
The naximum number of
Target BSs to which to
send HO-REQ message
through the backbone.
Optional
255
0 - 255
[min-actiontime <(0 to
255 StepSize 1)> ]
The minimum acceptable
action time in the Serving
BS (in frames)
Optional
0 - 255
[max-actiontime <(0 to
255 StepSize 1)> ]
The maximum acceptable
action time in the Serving
BS (in frames)
Optional
255
0 - 255
bs configuration mode
Restoring the Default Values of Handover Negotiation at
SBS Parameters
To restore some or all of the Handover Negotiation at SBS parameters to their
default values, run the following command:
npu(config-bs-66053)# no honegotiation-sbs [selectcoefficient] [max-tbs]
[min-actiontime] [max-actiontime]
You can restore only some parameters to their default values by specifying only
those parameters. For example, to restore only the max-tbs parameter to the
default value, run the following command:
npu(config-bs-66053)# no honegotiation-sbs max-tbs
This parameter will be restored to its default value, while the other parameters
will remain unchanged.
To restore all Handover Negotiation at SBS parameters to their default value, run
the following command:
npu(config-bs-66053)# no honegotiation-sbs
4Motion
600
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
NOTE
Refer to Section 4.8.12.1 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053)# no honegotiation-sbs [selectcoefficient ]
[max-tbs ] [min-actiontime ] [max-actiontime ]
Privilege
Level
10
Command
Modes
bs configuration mode
4.8.12.3
Displaying Configuration Information for Handover
Negotiation at SBS Parameters
To display configuration information for Handover Negotiation at SBS parameters,
run the following command:
npu# show honegotiation-sbs bs [<(1 to 16777215 StepSize 1)
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Handover Negotiation at SBS parameters of BS 66053,
run the following command:
npu# show honegotiation-sbs bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show honegotiation-sbs bs
Command
Syntax
npu# show honegotiation-sbs bs [<(1 to 16777215 StepSize 1)
Privilege
Level
4Motion
601
System Manual
Chapter 4 - Operation and Administration Using the CLI
Syntax
Description
Display
Format
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display Handover Negotiation
at SBS parameters of a
specific BS. Do not specify a
value for this parameter if you
want to display Handover
Negotiation at SBS
parameters of all BSs.
BSIDLSB
:
(for each
existing BS
if requested
for all BSs)
Command
Modes
Global command mode
4.8.13 Managing Handover Negotiation at TBS
Parameters
After enabling the BS configuration mode, you can execute the following tasks:
Configure one or more of the Handover Negotiation at TBS parameters (refer to
Section 4.8.13.1).
Restore the default values of some or all of the Handover Negotiation at TBS
parameters (refer to Section 4.8.13.2).
You can display configuration information for the Handover Negotiation at TBS
parameters of a selected or all existing BSs (refer to Section 4.8.13.3).
4Motion
602
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.13.1
Managing BSs
Configuring Handover Negotiation at TBS Parameters
To configure the Handover Negotiation at TBS Parameters:
From the BS configuration mode, run the following command:
npu(config-bs-66053)# honegotiation-tbs [defaultactiontime <(0 to 255 StepSize
1)>] [fastrangingalloc <(0 to 255 StepSize 1)>]
IMPORTANT
When creating a new BS, at least one of the Handover Negotiation at TBS parameters must be
configured explicitly (even if configured to the default value).
Command
Syntax
npu(config-bs-66053)# honegotiation-tbs [defaultactiontime <(0 to
255 StepSize 1)> ] [fastrangingalloc <(0 to 255 StepSize 1)> ]
Privilege
Level
10
Syntax
Description
Command
Modes
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
defaultactiontime <(0
to 255 StepSize 1)>
The number of frames
until allocation of
non-contention based
ranging opportunity at
target BS.
Optional
0 - 255
fastrangingalloc <(0 to
255 StepSize 1)>
The number of
consecutive fast ranging
opportunities the target
BS will allocate to an
incoming HO MS.
Optional
0 - 255
bs configuration mode
603
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.13.2
Managing BSs
Restoring the Default Values of Handover Negotiation at
TBS Parameters
To restore some or all of the Handover Negotiation at TBS parameters to their
default values, run the following command:
npu(config-bs-66053)# no honegotiation-tbs [defaultactiontime]
[fastrangingalloc]
You can restore only one parameter to the default values by specifying only that
parameters. For example, to restore only the fastrangingalloc parameter to the
default value, run the following command:
npu(config-bs-66053)# no honegotiation-tbs fastrangingalloc
This parameter will be restored to its default value, while the other parameter will
remain unchanged.
To restore all Handover Negotiation at TBS parameters to their default value, run
the following command:
npu(config-bs-66053)# no honegotiation-tbs
NOTE
Refer to Section 4.8.13.1 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053)# no honegotiation-stbs [defaultactiontime ]
[fastrangingalloc ]
Privilege
Level
10
Command
Modes
bs configuration mode
4.8.13.3
Displaying Configuration Information for Handover
Negotiation at TBS Parameters
To display configuration information for Handover Negotiation at TBS parameters,
run the following command:
npu# show honegotiation-tbs bs [<(1 to 16777215 StepSize 1)
4Motion
604
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Specify the BS ID if you want to display configuration for a particular BS. For
example, to display the Handover Negotiation at TBS parameters of BS 66053, run
the following command:
npu# show honegotiation-tbs bs 66053
Do not specify this parameter if you want to view configuration information for all
existing BSs. To display information for all BSs, run the following command:
npu# show honegotiation-tbs bs
Command
Syntax
npu# show honegotiation-tbs bs [<(1 to 16777215 StepSize 1)
Privilege
Level
Syntax
Description
Display
Format
(for each
existing BS
if requested
for all BSs)
Command
Modes
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display Handover Negotiation
at TBS parameters of a
specific BS. Do not specify a
value for this parameter if you
want to display Handover
Negotiation at TBS
parameters of all BSs.
BSIDLSB
:
DefaultActionTime(frames)
:
FastRangingallocations
:
Global command mode
605
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
4.8.14 Managing Neighbor BSs
To configure a Neighbor BS:
Enable the Neighbour BS configuration mode for the selected Neighbour BS
(refer to Section 4.8.14.1)
You can now execute any of the following tasks:
»
Configure one or more of the parameters tables of the Neighbor BS (refer to
Section 4.8.14.2)
»
Restore the default values of parameters in one or more of the parameters
tables of the Neighbor BS (refer to Section 4.8.14.3)
»
Terminate the Neighbor BS configuration mode (refer to Section 4.8.14.4)
In addition, you can, at any time, display configuration information for each of the
parameters tables of the Neighbour BS (refer to Section 4.8.14.6) or delete an
existing Neighbor BS (refer to Section 4.8.14.5).
4.8.14.1
Enabling the Neighbor BS Configuration Mode\Creating a
Neighbor BS
To configure the parameters of a Neighbour BS, first enable the Neighbour BS
configuration mode for the specific Neighbour BS. Run the following command to
enable the Neighbour BS configuration mode. You can also use this command to
create a new Neighbour BS.
npu(config-bs-66053)# nbr <(1 to 16777215 StepSize 1)>
Note that for a new Neighbour BS this command only defines the Neighbour BS
ID, and that the Neighbour BS is not fully created until completing configuration
of all mandatory parameters and executing the apply command (must be
executed before exiting the Neighbour BS configuration mode). Also when
updating an existing Neighbour BS, the apply command must be executing prior
to termination the Neighbour BS configuration mode.
For example, to define a new Neighbour BS with a BS ID 66055, or to enable the
configuration mode for Neighbour BS 66055, run the following command:
npu(config-bs-66053)# nbr 66055
4Motion
606
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
If you use this command to create a new Neighbour BS, the configuration mode
for this Neighbour BS is automatically enabled, after which you can execute any
of the following tasks:
Configure one or more of the parameters tables of the Neighbour BS (refer to
Section 4.8.14.2)
Restore the default values of parameters in one or more of the parameters
tables of the Neighbour BS (refer to Section 4.8.14.3)
After executing the above tasks, you can terminate the Neighbour BS
configuration mode (refer to Section 4.8.14.4) and return to the BS configuration
mode.
Note that for properly completing the configuration of a Neighbour BS the apply
command must be executed prior to exiting the Neighbour BS configuration mode.
Command
Syntax
npu(config-bs-66053)# nbr <(1 to 16777215 StepSize 1)>
Privilege
Level
10
Syntax
Description
Command
Modes
Parameter
Description
Presence
nbr <(1 to 16777215
StepSize 1)>
The BS ID (BSIDLSB) of the
Neighbour BS
Mandatory
Default
Value
Possible
Values
1 - 16777215
bs configuration mode
For example, to define Neighbor BS 66055 for bs-68000, run the following
command:
npu(config-bs-66053)# nbr 68000
NOTE
The following examples are for Neighbour BS configuration mode for bs-66053, neighbour bs (nbr)
68000.
4Motion
607
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.14.2
Managing BSs
Configuring Neighbor BS Parameters
After enabling the Neighbor BS configuration mode you can configure the
following parameters tables:
General (refer to Section 4.8.14.2.1)
Required C/N Level (refer to Section 4.8.14.2.2)
Trigger Setup (refer to Section 4.8.14.2.3)
Triggers (refer to Section 4.8.14.2.4)
IMPORTANT
After completing the Neighbour BS configuration,do not forget to execute the apply command
before exiting the Neighbour BS configuration mode:
npu(config-bs-66053-nbr-68000)# apply
4.8.14.2.1
Configuring General Neighbor BS Parameters
The General Neighbor BS Parameters table enables defining the general
parameters of the Neighbor BS.
To configure the General Neighbor BS parameters, run the following command:
npu(config-bs-66053-nbr-68000)# general [syncind {unsynchronized |
timeSynchronized | timeAndFrequencySynchronized}] [eirp <(-128 to 127
StepSize 1)>] [srvcsupport ] [bw {fiveMHz | tenMHz | sevenMHz}]
[feedbackzone-permbase <(0 to 69 StepSize 1)>] [ucd-configchangecount <(0 to
255 StepSize 1)>] [dcd-configchangecount <(0 to 255 StepSize 1)>] [eirx-pir-max
<(-140 to -40 StepSize 1)>] [frequency <(2302.5 to 2357.5 StepSize 0.125) |
(2498.5 to 2687.5 StepSize 0.125) | (3402.5 to 3597.5 StepSize 0.125) | (3602.5
to 3797.5 StepSize 0.125)>] [restartcount <(0 to 255 StepSize 1)>] [preamble-idx
<(0 to 113 StepSize 1)>]
IMPORTANT
When creating a new Neighbour BS, all mandatory Neighbour BS General parameters must be
configured.
4Motion
608
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Syntax
Managing BSs
npu(config-bs-66053-nbr-68000)# general [syncind {unsynchronized |
timeSynchronized | timeAndFrequencySynchronized} ] [eirp <(-128 to
127 StepSize 1)> ] [srvcsupport ] [bw {fiveMHz |
tenMHz | sevenMHz} ] [feedbackzone-permbase <(0 to 69 StepSize 1)>
] [ucd-configchangecount <(0 to 255 StepSize 1)>]
[dcd-configchangecount <(0 to 255 StepSize 1)> ] [eirx-pir-max
<(-140 to -40 StepSize 1)> ] [frequency <(2302.5 to 2357.5
StepSize 0.125) | (2498.5 to 2687.5 StepSize 0.125) | (3402.5 to
3597.5 StepSize 0.125) | (3602.5 to 3797.5 StepSize 0.125)> ]
[restartcount <(0 to 255 StepSize 1)>] [preamble-idx <(0 to 113
StepSize 1)> ]
Privilege
Level
Syntax
Description
4Motion
10
Parameter
Description
Presence
Default
Value
Possible Values
[syncind
{unsynchronized |
timeSynchronized |
timeAndFrequency
Synchronized} ]
Time/Frequency
synchronization
indicator.
Optional
timeAndFr
equencySy
nchronized
unsynchronized
[eirp <(-128 to 127
StepSize 1)> ]
Neighbour BS EIRP
In the current release
should always be set to
timeAndFrequencySyn
chronized.
609
timeSynchronized
timeAndFrequency
Synchronized
Mandatory
When
creating a
new
Neighbour
BS.
N/A
-128 to 127
System Manual
Chapter 4 - Operation and Administration Using the CLI
[srvcsupport
]
Managing BSs
Scheduling Service
Support. Two
hexadeximal digits that
can be presented as 8
bits where tbits 5-7 are
always 0. Bits 0-4
indicate whether
specific services are
supported, where a
value of 1 means that
the service is
supported: UGS (0),
RT-PS(1), NRT-PS(2),
BE(3), ERT-PS(4).
Optional
c8
(11001000,
meaning
that the BS
supports
UGS,
RT-PS and
ERT-PS
scheduling
services).
Two hexadecimal
digits.
Should be taken from
the displayed
information for
Handover Control
(hoctrl) in the relevant
BS (see
Section 4.8.23.3.
[bw {fiveMHz |
tenMHz |
sevenMHz} ]
[feedbackzone-per
mbase <(0 to 69
StepSize 1)> ]
The bandwidth of
neighbour BS.
Should be taken from
Baseband bandwidth
parameter of the
relevant BS (see
Section 4.8.18.2)
The first uplink zone
permutation base of
the neighbor BS.
In current release this
equals the feedback
zone permutation base
(see
Section 4.8.19.5.8)
[ucd-configchangec
ount <(0 to 255
StepSize 1)>]
UCD configuration
change count of
neighbor BS
Should be taken from
displayed UCD
information for the
relevant BS (see
fiveMHz
Mandatory
When
creating a
new
Neighbour
BS.
N/A
Mandatory
When
creating a
new
Neighbour
BS.
N/A
0 - 69
Mandatory
When
creating a
new
Neighbour
BS.
N/A
0 - 255
tenMHz
sevenMHz
Section 4.8.15.3
4Motion
610
System Manual
Chapter 4 - Operation and Administration Using the CLI
[dcd-configchangec
ount <(0 to 255
StepSize 1)> ]
Managing BSs
DCD configuration
change count of
neighbor BS
Should be taken from
displayed DCD
information for the
relevant BS (see
Mandatory
When
creating a
new
Neighbour
BS.
N/A
0 - 255
Optional
-124
-140 to -40
Mandatory
When
creating a
new
Neighbour
BS.
N/A
2302.5 to 2357.5
Section 4.8.16.3
eirx-pir-max <(-140
to -40 StepSize 1)>
The required effective
isotropic received
power at the Neighbor
BS for Initial ranging, in
dBm.
Should be taken from
Power Control
maxeirxp (see
Section 4.8.6.2.2)
[frequency
<(2302.5 to 2357.5
StepSize 0.125) |
(2498.5 to 2687.5
StepSize 0.125) |
(3402.5 to 3597.5
StepSize 0.125) |
(3602.5 to 3797.5
StepSize 0.125)> ]
Downlink center
frequency of neighbor
BS.
Should be taken from
RF frequency
parameter of the
relevant BS (see
Section 4.8.17.2)
in steps of 0.125)
2498.5 to 2687.5
in steps of 0.125
3402.5 to 3597.5
in steps of 0.125
3602.5 to 3797.5
in steps of 0.125
restartcount <(0 to
255 StepSize 1)> ]
This value is
incremented by one
whenever the neighbor
BS restarts.
Should be taken from
displayed DCD
information for the
relevant BS (see
Mandatory
When
creating a
new
Neighbour
BS.
N/A
0 - 255
Section 4.8.16.3
4Motion
611
System Manual
Chapter 4 - Operation and Administration Using the CLI
[preamble-idx <(0
to 113 StepSize 1)>
Managing BSs
Neighbour BS
Preamble Index.
Should be the same as
preamble-idx in
displayed information
of Airframe General
parameters of the
relevant BS (see
Mandatory
When
creating a
new
Neighbour
BS.
N/A
0 - 113
Section 4.8.19.5.1
Command
Modes
4.8.14.2.2
bs neighbour bs configuration mode
Configuring the Neighbor BS Required C/N Level Parameters
The Neighbor BS Required C/N Levels table enables defining the Carrier to Noise
Ratios required for various types of transmissions.
The configured values should be the same as those defined for the applicable
Power Control Required C/N Level parameters (see Section 4.8.6.5.3) in the
neighbor BS.
To configure the Neighbor BS Required C/N Levels, run the following command:
npu(config-bs-66053-nbr-68000)# requiredcnr [ack <(-20 to 50 StepSize 1)>]
[cqi <(-20 to 50 StepSize 1)>] [cdma <(-20 to 50 StepSize 1)>] [qpsk-1by2 <(-20 to
50 StepSize 1)>] [qpsk-3by4 <(-20 to 50 StepSize 1)>] [qam16-1by2 <(-20 to 50
StepSize 1)>] [qam16-3by4 <(-20 to 50 StepSize 1)>] [qam64-1by2 <(-20 to 50
StepSize 1)>] [qam64-2by3 <(-20 to 50 StepSize 1)>] [qam64-3by4 <(-20 to 50
StepSize 1)>] [qam64-5by6 <(-20 to 50 StepSize 1)>]
IMPORTANT
When creating a new Neighbour BS, at least one of the Neighbour BS Required C/N Level
parameters must be configured explicitly (even if configured to the default value).
Command
Syntax
npu(config-bs-66053-nbr-68000)# requiredcnr [ack <(-20 to 50
StepSize 1)> ] [cqi <(-20 to 50 StepSize 1)> ] [cdma <(-20 to 50
StepSize 1)> ] [qpsk-1by2 <(-20 to 50 StepSize 1)> ] [qpsk-3by4
<(-20 to 50 StepSize 1)> ] [qam16-1by2 <(-20 to 50 StepSize 1)> ]
[qam16-3by4 <(-20 to 50 StepSize 1)> ] [qam64-1by2 <(-20 to 50
StepSize 1)> ] [qam64-2by3 <(-20 to 50 StepSize 1)> ] [qam64-3by4
<(-20 to 50 StepSize 1)> ] [qam64-5by6 <(-20 to 50 StepSize 1)> ]
4Motion
612
System Manual
Chapter 4 - Operation and Administration Using the CLI
Privilege
Level
Syntax
Description
4Motion
Managing BSs
10
Parameter
Description
Presence
Default
Value
Possible
Values
[ack <(-20 to 50
StepSize 1)> ]
The C/N in dB required for
sending ACK, reported by the
Neighbour BS to the MS for
power control purposes.
Optional
-20 to 50
[cqi <(-20 to 50
StepSize 1)> ]
The C/N in dB required for
sending CQI, reported by the
Neighbour BS to the MS for
power control purposes.
Optional
-20 to 50
[cdma <(-20 to 50
StepSize 1)> ]
The C/N in dB required for
transmitting CDMA, reported by
the Neighbour BS to the MS for
power control purposes.
Optional
-20 to 50
[qpsk-1by2 <(-20 to
50 StepSize 1)> ]
The C/N in dB required for
transmitting using QPSK 1/2,
reported by the Neighbour BS to
the MS for power control
purposes.
Optional
14
-20 to 50
[qpsk-3by4<(-20 to
50 StepSize 1)> ]
The C/N in dB required for
transmitting using QPSK 3/4,
reported by the Neighbour BS to
the MS for power control
purposes.
Optional
16
-20 to 50
[qam16-1by2 <(-20
to 50 StepSize 1)> ]
The C/N in dB required for
transmitting using 16QAM 1/2,
reported by the Neighbour BS to
the MS for power control
purposes.
Optional
18
-20 to 50
[qam16-3by4 <(-20
to 50 StepSize 1)> ]
The C/N in dB required for
transmitting using 16QAM 3/4,
reported by the Neighbour BS to
the MS for power control
purposes.
Optional
22
-20 to 50
613
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Modes
4.8.14.2.3
Managing BSs
qam64-1by2 <(-20
to 50 StepSize 1)> ]
The C/N in dB required for
transmitting using 64QAM 1/2,
reported by the Neighbour BS to
the MS for power control
purposes.
Optional
23
-20 to 50
[qam64-2by3 <(-20
to 50 StepSize 1)> ]
The C/N in dB required for
transmitting using 64QAM 2/3,
reported by the Neighbour BS to
the MS for power control
purposes.
Optional
23
-20 to 50
[qam64-3by4 <(-20
to 50 StepSize 1)> ]
The C/N in dB required for
transmitting using 64QAM 3/4,
reported by the Neighbour BS to
the MS for power control
purposes.
Optional
23
-20 to 50
[qam64-5by6 <(-20
to 50 StepSize 1)> ]
he C/N in dB required for
transmitting using 64QAM 5/6,
reported by the Neighbour BS to
the MS for power control
purposes.
Optional
23
-20 to 50
bs neighbour bs configuration mode
Configuring Trigger Setup Parameters
To configure the Neighbor BS Trigger Setup parameters, run the following
command:
npu(config-bs-66053-nbr-68000)# triggersetup [hysteresismargin <(0 to 255
StepSize 1)>] [timetotrigger <(0 to 255 StepSize 1)>] [avgduration-rssi <(0 to 255
StepSize 1)>] [avgduration-cinr <(0 to 255 StepSize 1)>] [avgduration-rtd <(0 to
255 StepSize 1)>]
The configured values should be the same as those defined for the applicable
Trigger Setup parameters (see Section 4.8.10.3) in the neighbor BS.
IMPORTANT
When creating a new Neighbour BS, at least one of the Neighbour BS Trigger Setup parameters
must be configured explicitly (even if configured to the default value).
4Motion
614
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Command
Syntax
npu(config-bs-66053-nbr-68000)# triggersetup [hysteresismargin
<(0 to 255 StepSize 1)> ] [timetotrigger <(0 to 255 StepSize 1)> ]
[avgduration-rssi <(0 to 255 StepSize 1)> ] [avgduration-cinr <(0
to 255 StepSize 1)> ] [avgduration-rtd <(0 to 255 StepSize 1)> ]
Privilege
Level
10
Syntax
Description
Command
Modes
4.8.14.2.4
Refer to Section 4.8.10.1
bs neighbour bs configuration mode
Configuring Neighbor BS Triggers Parameters
To configure the Neighbor BS Triggers parameters, run the following command:
npu(config-bs-66053-nbr-68000)# triggers-
Each Trigger is configured separately. This is the general structure of the
command.
The configured trigger names and values should be the same as those defined for
the applicable Triggers parameters (see Section 4.8.9.2) in the neighbor BS.
IMPORTANT
When creating a new Neighbour BS, at least one of the Neighbour BS Trigges parameters must be
configured.
Command
Syntax
npu(config-bs-66053-nbr-68000)# triggers-
Privilege
Level
10
Syntax
Description
4Motion
Parameter
Description
615
Presence
Default
Value
Possible
Values
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
The Trigger name.
Mandatory
N/A
See
Table 4-3
Command
Modes
4.8.14.3
Defines the threshold
value for the Trigger.
Mandatory
N/A
See
Table 4-3
bs neighbour bs configuration mode
Restoring Default Values for Neighbor BS Configuration
Parameters
After enabling the Neighbor BS configuration mode you can restore the default
values for non-mandatory parameters in the following parameters tables:
General (refer to Section 4.8.14.3.1)
Required C/N Level (refer to Section 4.8.14.3.2)
Trigger Setup (refer to Section 4.8.14.3.3)
4.8.14.3.1
Restoring the Default Values of Neighbor BS General Parameters
To restore one or all of the Neighbor BS non-mandatory General parameters to
their default values, run the following command:
npu(config-bs-66053-nbr-68000)# no general [syncind] [srvcsupport]
[eirx-pir-max]
You can restore only some parameters to the default values by specifying only
those parameters. For example, to restore only the syncind to the default value,
run the following command:
npu(config-bs-66053-nbr-68000)# no general syncind
The parameter will be restored to its default value, while the other parameters will
remain unchanged.
To restore all non-mandatory parameters to their default value, run the following
command:
npu(config-bs-66053-nbr-68000)# no general
4Motion
616
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
NOTE
Refer to Section 4.8.14.2.1 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-nbr-68000)# no general [syncind ]
Privilege
Level
10
Command
Modes
bs neighbour bs configuration mode
4.8.14.3.2
[srvcsupport][eirx-pir-max ]
Restoring the Default Values of Neighbor BS Required C/N Level
Parameters
To restore some or all of the Neighbor BS Required C/N Levels parameters to their
default values, run the following command:
npu(config-bs-66053-bs-68000)# no requiredcnr [ack] [cqi] [cdma] [qpsk-1by2]
[qpsk-3by4] [qam16-1by2] [qam16-3by4] [qam64-1by2] [qam64-2by3]
[qam64-3by4] [qam64-5by6]
You can restore only some parameters to their default values by specifying only
those parameter. For example, to restore only the ack and cqi parameters to the
default values, run the following command:
npu(config-bs-66053-nbr-68000)# no requiredcnr ack cqi
These parameters will be restored to their default value, while the other
parameters will remain unchanged.
To restore all Neighbor BS Required C/N Levels parameters to their default value,
run the following command:
npu(config-bs-66053-nbr-68000)# no requiredcnr
NOTE
Refer to Section 4.8.14.2.2 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-nbr-68000)# no requiredcnr [ack ] [cqi ] [cdma
] [qpsk-1by2 ] [qpsk-3by4 ] [qam16-1by2 ] [qam16-3by4 ]
[qam64-1by2 ] [qam64-2by3 ] [qam64-3by4 ] [qam64-5by6 ]
4Motion
617
System Manual
Chapter 4 - Operation and Administration Using the CLI
Privilege
Level
10
Command
Modes
bs neighbour bs configuration mode
4.8.14.3.3
Managing BSs
Restoring the Default Values of Neighbor BS Trigger Setup Parameters
To restore some or all of the Neighbor BS Trigger Setup parameters to their default
values, run the following command:
npu(config-bs-66053-nbr-68000)# no triggersetup [hysteresismargin]
[timetotrigger] [avgduration-rssi] [avgduration-cinr] [avgduration-rtd]
You can restore only some parameters to their default values by specifying only
those parameters. For example, to restore only the hysteresismargin parameter to
the default value, run the following command:
npu(config-bs-66053-nbr-68000)# no triggersetup hysteresismargin
This parameter will be restored to its default value, while the other parameters
will remain unchanged.
To restore all Neighbor BS Trigger Setup parameters to their default value, run the
following command:
npu(config-bs-66053-nbr-68000)# no triggersetup
NOTE
Refer to Section 4.8.14.2.3 for a description and default values of these parameters.
Command
Syntax
npu(config-bs-66053-nbr-68000)# no triggersetup [hysteresismargin ]
[timetotrigger ] [avgduration-rssi] [avgduration-cinr]
[avgduration-rtd ]
Privilege
Level
10
Command
Modes
bs neighbour bs configuration mode
4Motion
618
System Manual
Chapter 4 - Operation and Administration Using the CLI
4.8.14.4
Managing BSs
Terminating the Neighbor BS Configuration Mode
Run the following command to terminate the Neighbor BS configuration mode:
npu(config-bs-66053-nbr-68000)# exit
IMPORTANT
Do not forget to execute the apply command before terminating the Neighbour BS configuration
mode: npu(config-bs-66053-nbr-68000)# apply
Command
Syntax
npu(config-bs-66053-nbr-68000)# exit
Privilege
Level
10
Command
Modes
bs neighbour bs configuration mode
4.8.14.5
Deleting a Neighbor BS
Run the following command from the BS configuration mode to delete a Neighbor
BS:
npu(config-bs 66053)# no nbr <(1 to 16777215 StepSize 1)>
Command
Syntax
npu(config-bs 66053)# no nbr <(1 to 16777215 StepSize 1)>
Privilege
Level
10
Syntax
Description
4Motion
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to
16777215
StepSize 1)>
The Neighbour BS ID
(bs-id-lsb)
Mandatory
N/A
1-16777215
619
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Modes
4.8.14.6
Managing BSs
bs configuration mode
Displaying Configuration Information for Neighbor BS
Parameters
You can display the current configuration information for the following Neighbor
BS parameters tables:
General (refer to Section 4.8.14.6.1)
Required C/N Level (refer to Section 4.8.14.6.2)
Trigger Setup (refer to Section 4.8.14.6.3)
Triggers (refer to Section 4.8.14.6.4)
All (refer to Section 4.8.14.6.5)
4.8.14.6.1
Displaying Configuration Information for Neighbor BS General
Parameters
To display configuration for the Neighbor BS General parameters, run the
following command:
npu# show nbr-general bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to
16777215 StepSize 1)>]
Specify the BS ID and the Neighbor BS ID (bs-id-lsb) if you want to display
configuration for a particular Neighbor BS in a particular BS. For example, to
display the General parameters of Neighbor BS 68000 in BS 66503, run the
following command:
npu# show nbr-general bs 66053 bs-id-lsb 68000
Do not specify these parameters if you want to view configuration information for
all existing Neighbor BSs in all existing BSs. To display information for all
Neighbor BSs in all BSs, run the following command:
npu# show nbr-general bs
Command
Syntax
4Motion
npu# show nbr-general bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to 16777215
StepSize 1)> ]
620
System Manual
Chapter 4 - Operation and Administration Using the CLI
Privilege
Level
Syntax
Description
4Motion
Managing BSs
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
bs-id-lsb <(1 to
16777215
StepSize 1)>
The Neighbour BS ID.
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the General
parameters of a specific
Neighbour BS in a specific
BS. Do not specify a value for
this parameter if you want to
display the General
parameters of all Neighbour
BSs in all BSs.
Specify a value for this
parameter if you want to
display the General
parameters of a specific
Neighbour BS in a specific
BS. Do not specify a value for
this parameter if you want to
display the General
parameters of all Neighbour
BSs in all BSs.
621
System Manual
Chapter 4 - Operation and Administration Using the CLI
Display
Format
(for each
existing
Neighbour
BS in each
of the
existing BSs
if requested
for all)
Command
Modes
4.8.14.6.2
Managing BSs
BSIDLSB
:
NeighborBSIDLSB
:
SynchronizationIndicator
:
EIRP
:
SchedulingServiceSupport
:
Bandwidth(MHz)
:
UplinkFeedbackZonePermutationBase
:
UplinkDataZoneSub-ChannelsAllocated
:
UCDConfigurationChangeCount
:
DCDConfigurationChangeCount
:
IsotropicRecPwrForInitialRanging
:
CenterFrequency(MHz)
:
RestartCount
:
PreambleIndex
:
Global command mode
Displaying Configuration Information for Neighbor BS Required C/N
Level Parameters
To display configuration for the Neighbor BS Required C/N Level parameters, run
the following command:
npu# show nbr-requiredcnr bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to
16777215 StepSize 1)>]
Specify the BS ID and the Neighbor BS ID (bs-id-lsb) if you want to display
configuration for a particular Neighbor BS in a particular BS. For example, to
display the Required C/N Level parameters of Neighbor BS 68000 in BS 66503,
run the following command:
npu# show nbr-requiredcnr bs 66053 bs-id-lsb 68000
Do not specify these parameters if you want to view configuration information for
all existing Neighbor BSs in all existing BSs. To display information for all
Neighbor BSs in all BSs, run the following command:
npu# show nbr-requiredcnr bs
4Motion
622
System Manual
Chapter 4 - Operation and Administration Using the CLI
Managing BSs
Command
Syntax
npu# show nbr-requiredcnr bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to 16777215
Privilege
Level
Syntax
Description
4Motion
StepSize 1)> ]
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
bs-id-lsb <(1 to
16777215
StepSize 1)>
The Neighbour BS ID.
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the Required C/N
Level parameters of a specific
Neighbour BS in a specific
BS. Do not specify a value for
this parameter if you want to
display the Required C/N
Level parameters of all
Neighbour BSs in all BSs.
Specify a value for this
parameter if you want to
display the Required C/N
Level parameters of a specific
Neighbour BS in a specific
BS. Do not specify a value for
this parameter if you want to
display the Required C/N
Level parameters of all
Neighbour BSs in all BSs.
623
System Manual
Chapter 4 - Operation and Administration Using the CLI
Display
Format
(for each
existing
Neighbour
BS in each
of the
existing BSs
if requested
for all)
Command
Modes
4.8.14.6.3
Managing BSs
BSIDLSB
:
NeighborBSIDLSB
:
RequiredCNRforACK
:
RequiredCNRforCQI
:
RequiredCNRforCDMA
:
RequiredCNRforQPSK1/2
:
RequiredCNRforQPSK3/4
:
RequiredCNRfor16QAM1/2
:
RequiredCNRfor16QAM3/4
:
RequiredCNRfor64QAM1/2
:
RequiredCNRfor64QAM2/3
:
RequiredCNRfor64QAM3/4
:
RequiredCNRfor64QAM5/6
:
Global command mode
Displaying Configuration Information for Neighbor BS Trigger Setup
Parameters
To display configuration for the Neighbor BS Trigger Setup parameters, run the
following command:
npu# show nbr-triggersetup bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to
16777215 StepSize 1)>]
Specify the BS ID and the Neighbor BS ID (bs-id-lsb) if you want to display
configuration for a particular Neighbor BS in a particular BS. For example, to
display the Trigger Setup parameters of Neighbor BS 68000 in BS 66503, run the
following command:
npu# show nbr-triggersetup bs 66053 bs-id-lsb 68000
Do not specify these parameters if you want to view configuration information for
all existing Neighbor BSs in all existing BSs. To display information for all
Neighbor BSs in all BSs, run the following command:
npu# show nbr-triggersetup bs
4Motion
624
System Manual
Chapter 4 - Operation and Administration Using the CLI
Command
Syntax
Privilege
Level
Syntax
Description
4Motion
Managing BSs
npu# show nbr-triggersetup bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to 16777215
StepSize 1)> ]
Parameter
Description
Presence
Default
Value
Possible
Values
<(1 to 16777215
StepSize 1)>
The BS ID
Optional
N/A
1-16777215
bs-id-lsb <(1 to
16777215
StepSize 1)>
The Neighbour BS ID.
Optional
N/A
1-16777215
Specify a value for this
parameter if you want to
display the Trigger Setup
parameters of a specific
Neighbour BS in a specific
BS. Do not specify a value for
this parameter if you want to
display the Trigger Setup
parameters of all Neighbour
BSs in all BSs.
Specify a value for this
parameter if you want to
display the Trigger Setup
parameters of a specific
Neighbour BS in a specific
BS. Do not specify a value for
this parameter if you want to
display the Trigger Setup
parameters of all Neighbour
BSs in all BSs.
625
System Manual
Chapter 4 - Operation and Administration Using the CLI
Display
Format
(for each
existing
Neighbour
BS in each
of the
existing BSs
if requested
for all)
Command
Modes
4.8.14.6.4
Managing BSs
BSIDLSB
: