Alvarion Technologies SUI-MMDS1 Indoor MMDS CPE transceiver User Manual New 24 Sept
Alvarion Ltd. Indoor MMDS CPE transceiver New 24 Sept
Contents
- 1. Indoor Subscriber unit radio user manual
- 2. New SUI user manual
- 3. New 24 Sept user manual
New 24 Sept user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 118490 |
| Application ID | DaG2o4AyrLs9y+eMfSH/dQ== |
| Document Description | New 24 Sept user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 14.73kB (184065 bits) |
| Date Submitted | 2000-09-24 00:00:00 |
| Date Available | 2000-10-30 00:00:00 |
| Creation Date | 0000-00-00 00:00:00 |
| Producing Software | Acrobat Distiller 3.0 for Windows |
| Document Lastmod | 2000-09-24 18:50:27 |
| Document Title | New 24 Sept user manual |
BreezeACCESS MMDS Indoor Subscriber Units SU-I/ID-MMDS Series Installation Manual July, 2000 Cat. No. 213099 Front Matter © 2000 by BreezeCOM Ltd. All rights reserved. No part of this publication may be reproduced in any material form without the written permission of the copyright owner. Trade Names BreezeACCESS, BreezeNET, BreezeLINK, BreezeVIEW and WIX are trade names of BreezeCOM Ltd. Other brand and product names are registered trademarks or trademarks of their respective companies. Statement of Conditions The information contained in this manual is subject to change without notice. BreezeCOM shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual or equipment supplied with it. Warranty In the following warranty text, “the Company” shall mean: • BreezeCOM Ltd., for products located outside the USA. • BreezeCOM Inc., for products located in the USA. This BreezeACCESS product is warranted against defects in material and workmanship for a period of one year from date of purchase. During this warranty period the Company will, at its option, either repair or replace products that prove to be defective. For warranty service or repair, the product must be returned to a service facility designated by the Company. Authorization to return products must be obtained prior to shipment. The buyer shall pay all shipping charges to the Company and the Company shall pay shipping charges to return the product to the buyer within the USA. The Company warrants that the firmware designed by it for use with the unit will execute its programming instructions when properly installed on the unit. The Company does not warrant that the operation of the unit or firmware will be uninterrupted or error-free. Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the buyer, buyer supplied interfacing, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or improper site preparation or maintenance. No other warranty is expressed or implied. The company specifically disclaims the implied warranties of merchantability and fitness for any particular purpose. SU-I/ID Installation Manual ii BreezeACCESS MMDS Series Front Matter BreezeCOM shall not be liable to any person for any special or indirect damages, including, but not limited to, loss of profits or revenues, loss of use or damage to any associated equipment, cost of capital, cost of substitute products, facilities or services, downtime costs or claims resulting from any cause whatsoever arising from or in any way connected with the manufacture, sale, handling, service, repair, maintenance or use of the products. In no event shall the company’s liability exceed the purchase price denoted on the invoice. Electronic Emission Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Information to User Any changes or modifications of equipment not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Safety Considerations For the following safety considerations, “Instrument” means the BreezeACCESS Subscriber or Access unit components and their cables. Caution To avoid shock, do not perform any servicing unless you are qualified to do so. To comply with FCC RF exposure requirements in section 1.1307, a minimum separation distance 20cm (8 inches) is required between this antenna and all persons. BreezeACCESS/MMDS Series iii SU-I/ID Installation Manual Front Matter Grounding Before connecting the instrument to the power line, verify that a suitable power cord is being used (the protective earth terminal of this instrument must be connected to the protective conductor of the power cord). The mains plug shall only be inserted in a socket outlet provided with a protective earth contact. If an extension cord (power cable) is used make sure it has a protective conductor (grounding). Line Voltage Before connecting this instrument to the power line, make sure that the voltage of the power source matches the requirements of the instrument: 100-250 VAC, 50-60 Hz. Radio The instrument transmits radio energy during normal operation. To avoid possible harmful exposure to this energy, do not stand or work for extended periods of time in front of its antenna. The long-term characteristics or the possible physiological effects of Radio Frequency Electromagnetic fields have not been yet fully investigated. Antenna Installation and Grounding Be sure that the outdoor antennas and the supporting structure are properly installed to eliminate any physical hazard to either people or property. Verify that the antenna mast is grounded so as to provide protection against voltage surges and static charges. Make sure that the installation of the antenna and cable is performed in accordance with all relevant national and local building and safety codes. SU-I/ID Installation Manual iv BreezeACCESS MMDS Series Table of Contents 1. INTRODUCTION ..................................................................................................................... 1 2. BASIC INSTALLATION ......................................................................................................... 2 2.1 Packing List .......................................................................................................................... 2 2.2 Other Required Items ............................................................................................................ 2 2.3 Installation Overview............................................................................................................ 3 2.4 Installation Guidelines .......................................................................................................... 3 2.4.1 Location of the Unit and Antenna(s) ............................................................................. 3 2.4.2 Location of the Antenna(s) ............................................................................................ 4 2.4.3 Antenna Diversity .......................................................................................................... 4 2.4.4 Antenna Polarization...................................................................................................... 5 2.4.5 Antenna Seal .................................................................................................................. 5 2.4.6 Lightning Protection ...................................................................................................... 5 2.5 Wall Mounting the Unit ........................................................................................................ 6 2.6 Connecting Antenna(s) to the Units (SU-ID units only)....................................................... 8 2.7 Connecting the Unit to the Power Supply and to the CPE.................................................... 9 3. CONFIGURING SYSTEM PARAMETERS ....................................................................... 10 3.1 Getting Started with the Local Terminal............................................................................. 10 3.2 Configuration Parameters ...................................................................................................12 3.3 Reset Unit............................................................................................................................ 14 4. ALIGNING THE ANTENNA ................................................................................................ 15 4.1 Aligning the Antenna Using the LEDs ............................................................................... 15 4.2 Aligning the Antenna Using the Site Survey Menu............................................................ 16 5. MAXIMUM DATA RATE CONFIGURATION ................................................................. 17 BreezeACCESS MMDS Series SU-I/ID Installation Manual Table of Contents 6. VERIFYING PROPER OPERATION.................................................................................. 18 6.1 Verifying Data Connectivity............................................................................................... 18 7. SPECIFICATIONS ................................................................................................................. 19 7.1 Radio ................................................................................................................................... 19 7.2 Data Communication .......................................................................................................... 19 7.3 Configuration and Management ......................................................................................... 20 7.4 Interfaces............................................................................................................................. 20 7.5 Electrical ............................................................................................................................. 20 7.6 Mechanical.......................................................................................................................... 20 7.7 Environmental..................................................................................................................... 20 7.8 Standards Compliance, General.......................................................................................... 21 APPENDIX A. AL 1 Lightning Arrestor.................................................................................. 22 APPENDIX B. USING TELNET............................................................................................. 24 APPENDIX C. MMDS CHANNELS AND FREQUENCIES ................................................. 25 SU-I/ID Installation Manual vi BreezeACCESS MMDS Series Table of Contents Table of Figures Figure 2-1. Wall Mounting the Unit .......................................................................................... 7 Figure 2-2. Wall Mounting Plate ...............................................................................................7 Figure 2-3. Tightening the Cable(s) to the Connector(s) ............................................................ 8 Figure 3-1. Main Menu ............................................................................................................ 11 Figure 3-2. Basic Configuration Menu .................................................................................... 13 Figure A-1. AL-1 Connection Block Diagram ........................................................................ 22 BreezeACCESS/MMDS Series vii SU-I/ID Installation Manual 1. INTRODUCTION This manual describes installation guidelines for BreezeACCESS/MMDS SU-I and SU-ID Subscriber Units. The BreezeACCESS IP Broadband Wireless Local Loop (WLL) system allows access service providers to provide high-speed IP connectivity services to their subscribers. To support IP-based services effectively BreezeACCESS systems employ wireless packet data switching technology. The BreezeACCESS MMDS line of products uses Frequency Hopping Spread Spectrum radios that operate in Time Duplex Division (TDD) mode in the 2.500GHz – 2.686GHz frequency range. The SU-I/ID-MMDS line of Subscriber Units comprises compact units that are designed for indoor installation. SU-I units include two 2dBi integrated antennas. SU-ID units have two RF connectors for detached diversity antennas. Detached antennas can be installed either indoors or outdoors, depending on the specific site conditions. The SU-I/ID-MMDS is available in two frequency bands: • • SU-I/ID-MMDSa products operate in the 2.500 - 2.600 GHz frequency band. SU-I/ID-MMDSb products operate in the 2.596 - 2.686 GHz frequency band. The SU-I/ID-MMDS series includes the following products: • • • SU-I/ID-1D-MMDSa/b: supports a single Ethernet device SU-I/ID-8D-MMDSa/b: supports up to eight Ethernet workstations/PCs SU-I/ID-BD-MMDSa/b: supports a LAN (a bridge functionality) Note: The information contained in this manual is applicable to BreezeACCESS MMDS units with software release 2.5. BreezeACCESS MMDS Series SU-I/ID Installation Manual Basic Installation 2. BASIC INSTALLATION 2.1 Packing List The SU-I/ID units are shipped with the following units and accessories. The exact packing list varies depending on system configuration and ordered equipment. • • • • SU-I unit (with two integral antennas) or SU-ID unit (without antennas) A 5 VDC universal power supply transformer Mounting bracket for wall or ceiling installation A torque key for antenna connectors (SU-ID units) 2.2 Other Required Items The following items must be available for the installation • Antenna(s)*and RF cable(s)*for SU-ID units (according to specific installation requirements) • A PC with terminal emulation program • A monitor cable* (supplied with each AU) • An Ethernet cable (straight) • Installation tools and materials Items marked with an asterisk (*) are available from BreezeCOM. SU-I/ID Installation Manual BreezeACCESS MMDS Series Basic Installation 2.3 Installation Overview Standard installation involves the following steps: 1. Verify that all components of the packing list, described in Section 2.1, are intact and verify availability of the required items listed in Section 2.2. 2. Install the unit and antenna(s) in optimal locations as described in Section 2.4. 3. Connect the antenna(s) to the unit as described in Section 2.6.(SU-ID units) 4. Connect the power supply to the unit as described in Section 2.7. 5. Connect the Ethernet port to the unit as described in Section 2.7. 6. Configure the basic system parameters as described in Section 3. 7. Align the antenna(s) for optimal connectivity and configure the Maximum Data Rate if applicable, as described in Chapters 4 and 5. 8. Check the functionality of the unit as described in Chapter 6. 2.4 Installation Guidelines This section describes the installation guidelines and the various considerations that must be taken into account when planning the installation. 2.4.1 Location of the Unit and Antenna(s) • The unit can be placed on a shelf, or can be attached to the ceiling or a wall using a mounting bracket. SU-ID units should be installed as near to the antenna(s) as possible to minimize loss of RF power in the cable(s). • Keep the units well away from sources of heat, such as radiators, airconditioners, etc. BreezeACCESS/MMDS Series SU-I/ID Installation Manual Basic Installation • For most applications, the most convenient choice is to use SU-I units, equipped with two integral 2dBi omni antennas. 2.4.2 Location of the Antenna(s) • Any physical object in the path between two units can cause signal attenuation. Common obstructions are buildings and trees. If a unit’s antenna is installed indoors, the walls and/or windows between the two sites are physical obstructions. If the antenna is positioned outdoors, any buildings or other physical structure such as trees, mountains or other natural geographic features higher than the antenna and situated in the path between the two sites can constitute obstructions. • Install indoor antennas as close as possible to a window (or wall if a window is not accessible) facing the required direction. Avoid metal obstacles such as metal window frames or metal film anti-glare windows in the transmission path. Install outdoor antennas high enough to avoid any obstacles, which may block the signal. • Position the antennas clear of metal furniture and away from moving metal objects such as metal fans or doors. • For best performance, position the antennas clear of radiation sources that emit in the 2.5 - 2.7 GHz frequency band, such as microwave ovens. 2.4.3 Antenna Diversity In applications where no multipath propagation is expected, a single antenna is sufficient to ensure good performance levels. However, in cases where multipath propagation exists, BreezeCOM recommends that two antennas be used. This takes advantage of space diversity capabilities. By using two antennas per unit, the system can select the best antenna on a per-packet basis (every several milliseconds). Multipath propagation is to be expected when there are potential reflectors between the Access Unit and Subscriber Units. These reflectors may be buildings or moving objects such as airplanes and motor vehicles. If this is the case, the radio signal does not travel in a straight line, but is reflected or deflected off of the object, creating multiple propagation paths. SU-I/ID Installation Manual BreezeACCESS MMDS Series Basic Installation When installing a single antenna, modify the transmit diversity option to either antenna 1 or antenna 2, according to the antenna being used. 2.4.4 Antenna Polarization Antenna polarization must be the same at either end of the link. In most applications, the preferred orientation is vertical polarization. Above-ground propagation of the signal is better when it is polarized vertically. To verify antenna polarization, refer to the assembly instructions supplied with the antenna set. For screw-on and detached omni antennas, make sure that the antennas are extended upward vertically in relation to the floor to achieve vertical polarization. 2.4.5 Antenna Seal When using outdoor antennas, you must seal the antenna connectors against rain. Otherwise the antennas are not suitable for use in outdoor installations. 2.4.6 Lightning Protection Lightning protection is designed to protect people, property and equipment by providing a path to ground for the lightning’s energy. The lightning arrestor diverts the strike energy to ground through a deliberate and controlled path instead of allowing it to choose a random path. Lightning protection for a building is more forgiving than protection of electronic devices. A building can withstand up to 100,000 volts, but electronic equipment may be damaged by just a few volts. Lightning protection entails connecting an antenna discharge unit (also called an arrestor) to each cable as close as possible to the point where it enters the building. It also entails proper grounding of the arrestors and of the antenna mast (if the antenna is connected to one). The lightning arrestor should be installed and grounded at the point where the cable enters the building. The arrestor is connected to the unit at one end and to the antenna at the other end. BreezeACCESS/MMDS Series SU-I/ID Installation Manual Basic Installation The professional installer you choose must be knowledgeable about lightning protection. The installer must install the lightning protector in a way that maximizes lightning protection. BreezeCOM offers the following high-quality lightning arrestor assembly: BreezeACCESS AL 1 Lightning Arrestor - Part No. 872905 5 ft (1.5m), “N” Male to “N” Female. Note: Detached antennas, whether installed indoors or out, should be installed ONLY by experienced antenna installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void the BreezeACCESS Product Warranty and may expose the end user to legal and financial liabilities. BreezeCOM and its resellers or distributors are not liable for injury, damage or violation of government regulations associated with the installation of detached antennas. 2.5 Wall Mounting the Unit Use the supplied brackets for wall mounting to install the unit on a wall or a ceiling. 1. Turn the unit so the rear panel is facing you. 2. Unscrew the two screws located at the antennas end of the unit (the top screws). 3. Align the Unit Mounting Slots (see Figure 2-2) with the slots you have just unscrewed. 4. Using the longer screws supplied with the wall mounts, screw the wall mount to the unit. 5. Align the Convenience Mounting Slots (see Figure 2-2) with the nails, push the wall mount against the wall and let it slide down until it rests on the nails. SU-I/ID Installation Manual BreezeACCESS MMDS Series Basic Installation Figure 2-1. Wall Mounting the Unit Special slots have been added to the wall mounts to allow for unobtrusive cable installation. These slots should be used to fasten cables coming out of the unit to the wall mounts, eliminating loose or tangled cable installations. Convenience M ounting Slots Unit M ounting Slots Cable Fastening S lots Figure 2-2. Wall Mounting Plate BreezeACCESS/MMDS Series SU-I/ID Installation Manual Basic Installation 2.6 Connecting Antenna(s) to the Units (SU-ID units only) For installation convenience, a torque key is included with all BreezeACCESS SU-ID units. WARNING: The use of improper tools for tightening antenna connection cables to BreezeACCESS SU-I units may result in damage to the cable connectors. Use the included torque key to tighten the cable(s) to the connector(s) on the side of the SU-I unit. The key is designed to prevent over tightening of the screws and protects the connectors from damage. Tighten the cable(s) to the connector(s) using the torque key. Figure 2-3. Tightening the Cable(s) to the Connector(s) If excessive pressure is applied to tighten the screws, the torque key will break. Note: Do not attempt to tighten the screws any further. This may damage the connectors on the BreezeACCESS SU-ID unit. SU-I/ID Installation Manual BreezeACCESS MMDS Series Basic Installation 2.7 Connecting the Unit to the Power Supply and to the CPE The unit operates on a power input of 5V DC, supplied by the power transformer included with the unit. 1. Plug the output jack of the power transformer into the DC input jack located on the rear panel of the unit. 2. Connect the supplied universal power transformer to a power outlet - 110/ 220VAC. 3. Use a straight Ethernet 10BaseT cable to connect a PC (SU-I/ID) or a hub (SU-I/ID-8D or SU-I/ID-BD) to the Ethernet port (marked UTP) located on the rear panel of the unit. BreezeACCESS/MMDS Series SU-I/ID Installation Manual Configuring System Parameters 3. CONFIGURING SYSTEM PARAMETERS After completing the installation process, as described in the preceding sections of this manual, proceed with configuration of the basic system parameters. This manual covers the configuration of basic installation parameters. Refer to the Administration Manual for information related to other parameters. Note: Optionally, the product can be configured using Telnet over the Ethernet port, after setting IP address. For further information refer to Appendix B. 3.1 Getting Started with the Local Terminal 1. Connect one end of the Monitor cable to the MON jack on the rear side of the unit. Connect the second end of the cable to the COM port of the terminal. The COM port connector on the Monitor cable is a 9 pin D-type plug. 2. Run a terminal emulation program (e.g., ProComm or Windows HyperTerminal) using the following setup: Baud rate 9600 Data bits Stop bits Parity None Flow Control Xon/Xoff Connector Available Com Port 3. Press Enter. The Select Access Level menu appears. Select the access level according to your authorized access level. You will be requested to enter your password. After entering the correct password press enter. The main menu appears (refer to Figure 3-1). SU-I/ID Installation Manual 10 BreezeACCESS MMDS Series Configuring System Parameters Unit Type BreezeACCESS/SU-I-1D Official Release Version – 2.5.3 Release Date: Tue Jul 18 21:12:54 2000 Software Version No. Main Menu ===================== 1 – Info Screens 2 – Unit Control 3 – Basic Configuration 4 – Site Survey 5 – Advanced Configuration BreezeACCESS >>> Unit Name Figure 3-1. Main Menu The appearance of the displayed Main Menu varies in accordance with the access level. • For users with read only access rights, only the Info Screens option is displayed. Users with this access level cannot access the Unit Control, Basic Configuration, Site Survey and Advanced Configuration menus. • For users with Installer access rights, the first four menu items (Info Screens, Unit Control, Basic Configuration and Site Survey) are displayed. Users with this access level cannot access the Advanced Configuration menu. • For users with Administrator access rights, the full Main Menu will be displayed. These users can access all the menu items. BreezeACCESS/MMDS Series 11 SU-I/ID Installation Manual Configuring System Parameters 4. Operate the monitor program as follows: • Type an option number to open/activate the option. You may need to press the Enter key in some cases. • Press the Esc key to exit a menu or an option. • You can log-out and exit the monitor program at any time by simultaneously pressing the Ctrl and X keys. • Reset the unit after making configuration changes for the new values to take effect. • You can view the current parameters’ configuration by selecting 1 in the Main Menu to Access the Info Screens menu, and than selecting 2 in the Info Screens menu to view the Basic Configuration parameters. 3.2 Configuration Parameters The following system parameters must be configured for each specific installation: • • • • • • • • Note: ESSID IP Address Subnet Mask Default Gateway Address Frequency Offset Hopping Band Flexible sub-bands Definition (if Flexible Hopping was selected in the Hopping Band menu) Transmit Antenna You must select Reset Unit in the Unit Control menu for the changes to take effect. Subscriber Units should be configured after the applicable Access Unit is operational. When configuring Subscriber Units, the first parameter that should be configured is the ESSID. Otherwise the unit will not successfully synchronize with the Access Unit and will continuously reset itself, thus interfering with the configuration process. SU-I/ID Installation Manual 12 BreezeACCESS MMDS Series Configuring System Parameters 1. From the main menu, type 3 to access the Basic Configuration menu. BreezeACCESS/SU-I-1D Official Release Version – 2.5.3 Release Date: Tue Jul 18 21:12:54 2000 Basic Configuration ==================== 1 – IP Address 2 – Subnet Mask 3 – Default Gateway Address 4 – ESSID 5 – Maximum Data Rate 6 - Frequency Offset H – Hopping Band F – Flexible sub-bands Definition G – Transmit Antenna P - Power Level S - Show Basic Configuration BreezeACCESS >>> Figure 3-2. Basic Configuration Menu 2. From the Basic Configuration menu, type 4 to access the ESSID selection screen. Enter the required ESSID. 3. Type 1 to access the IP Address selection screen. Enter the required IP address. 4. Type 2 to access the Subnet Mask selection screen. Enter the required subnet mask. 5. Type 3 to access the Default Gateway Address selection screen. Enter the required default gateway address. 6. Type 6 to access the Frequency Offset selection screen. Enter the required Frequency Offset BreezeACCESS/MMDS Series 13 SU-I/ID Installation Manual Configuring System Parameters 7. Type H to access the Hopping Band selection screen. Enter the required hopping band. 8. If Flexible Hopping was selected in the Hopping Band selection menu, type F to access the Flexible sub-bands Definition menu. Use the Add/Delete subbands screens to define the required frequencies. See Appendix C for a list of the standard frequencies as a function of the allocated channel(s). 9. Type G to access the Transmit Antenna selection screen. Enter the required selection (0 - use two antennas, 1 - use antenna #1, 2 - use antenna #2). For SU-I units with two integral antennas, select 0 - use two antennas. 3.3 Reset Unit 1. From the main menu, type 2 to access the Unit Control menu. 2. Type 1 to access the Reset Unit menu. Type 1 to reset the unit so that new configuration settings are applied. Note: Should you make any mistakes during configuration or encounter any problems associated with system configuration parameters, you may configure the unit back to the factory defaults, as follows: Type 2 in the Unit Control menu to access the Set Factory Defaults menu. Type in 2 (Set Factory defaults-Full) to load the default values. Reset the unit for the factory defaults values to take effect. SU-I/ID Installation Manual 14 BreezeACCESS MMDS Series Aligning the Antenna 4. ALIGNING THE ANTENNA Omni and low gain antennas do not require alignment due to their wide radiation pattern. High gain antennas have a narrow beamwidth, necessitating an alignment procedure in order to optimize the link. For Subscriber Units with directional antenna(s), you can either use the LED indicators on the front panel of the unit or view the Received Signal Strength Indication (RSSI) on the monitor. In most installations, alignment using the LEDs is sufficient. The RSSI reading can be used when finer alignment is required. Note: Antenna alignment of the Subscriber Unit is possible only after the Access Unit you wish to associate with is operational and the ESSID was properly configured. 4.1 Aligning the Antenna Using the LEDs 1. Synchronize the units by aligning the antenna manually to point to the base station until the WLNK indicator LED on the front panel of the unit illuminates. 2. Rotate the antenna left and/or right until you reach the point of signal quality reading on the quality (QLT) LEDs. The higher the number of illuminated LEDs the better is the quality of the link. Make sure that at all times, the front of the antenna faces the general direction of the Access Unit. 3. For proper operation, at least one (L) LED should be illuminated. If this is not possible, improve the link quality by placing the antenna at a higher point or in a different location. 4. After the antenna is optimally aligned, tighten the U-bolts (or metal band) to secure the antenna to the pole. BreezeACCESS/MMDS Series 15 SU-I/ID Installation Manual Aligning the Antenna 4.2 Aligning the Antenna Using the Site Survey Menu 1. Start the Monitor program as described in Section 3.1. 2. From the main menu, type 4 to access the Site Survey menu. Type 4 to start the Continuous RSSI Display. Each line in the display includes the number of frames that were received since the last measurement (total Rx) and the average RSSI for these frames. 3. Rotate the antenna left and/or right until you reach the point of maximum RSSI reading. Make sure that at all times, the front of the antenna faces the general direction of the Base Station. 4. For proper operation, the RSSI reading should be at least 52 units. When the maximum reading is less than 52 units, try to improve it by placing the antenna at a higher point or in a different location. For best performance it is recommended that the RSSI be higher than 76. 5. Press the Esc key to stop the test. 6. Tighten the U-bolts (or metal band) over the antenna to secure it to the pole. SU-I/ID Installation Manual 16 BreezeACCESS MMDS Series Maximum Data Rate Configuration 5. MAXIMUM DATA RATE CONFIGURATION 1. If the average RSSI reading using the Average RSSI Continuous Display is lower than 76, the default data rate of 3 Mbps is too high and the data rate of the unit should be configured accordingly: 2. From the main menu, type 3 to access the Basic Configuration menu. Type 5 to access the Maximum Data Rate menu. L Type 3 (3Mbps) if the RSSI reading is higher than 76 units. LL Type 2 (2Mbps) if the RSSI reading is between 66 to 76 units. LLL Type 1 (1Mbps) if the RSSI reading is lower than 66 units. 3. Reset the unit for the new configuration to become effective. BreezeACCESS/MMDS Series 17 SU-I/ID Installation Manual Verifying Proper Operation 6. VERIFYING PROPER OPERATION After completing the installation, and after connecting the unit to the AC mains, the system starts operation. To verify proper operation, view the LED panel located on the front panel of the unit. Table 6-1 lists the various LED states. Table 6-1. SU-I LEDs Name Description Functionality PWR Power supply On – After successful power up Off – Power off WLNK Wireless Link Activity Blinking – Receiving packets from the wireless link Off – no reception of packets from the wireless link ETH Ethernet activity Blinking – Reception of data from Ethernet LAN Off – No reception of data from Ethernet LAN QLT Very low quality reception or not synchronized with Access Unit, less than -81 dBm Quality of received RF signal Low quality reception (usually enabling 1Mbps traffic) from -81 to -77 dBm Medium quality reception (usually enabling 2 Mbps traffic) from -77 to -65 dBm High quality reception (usually enabling 3 Mbps traffic) greater than -65 dBm 6.1 Verifying Data Connectivity From the user’s PC or from a portable PC connected to the unit, Ping the unit or try to connect it to the Internet. SU-I/ID Installation Manual 18 BreezeACCESS MMDS Series Specifications 7. SPECIFICATIONS 7.1 Radio Frequency band A (MMDSa):2.500 – 2.600GHz band B (MMDSb):2.596 – 2.686GHz Radio Access Method FH-CDMA or TDMA Operation Mode Time Duplex Division Channel Bandwidth 2 MHz Output Power (at antenna port) 19dBm typical. Sensitivity -6 (dBm at antenna port, BER 1E10 ) 1Mbps 2Mbps 3Mbps -89 -82 -73 Data Rate 3Mbps max Modulation Multilevel GFSK 7.2 Data Communication Standard Compliance IEEE 802.3 CSMA/CD BreezeACCESS/MMDS Series 19 SU-I/ID Installation Manual Specifications 7.3 Configuration and Management Local Management Via MON port, Monitor program using terminal emulation Remote Management SNMP, Telnet, TFTP Remote Management Access From Wired LAN, Wireless Link SNMP Agents MIB II, Bridge MIB, Private MIBs Accounting RADIUS compatible client Security Authentication and filtering Software upgrade TFTP download 7.4 Interfaces RF (Antenna) 2 x SMA jacks Ethernet 10Base-T (RJ-45) Monitor 3-pin low profile Power DC socket for a power transformer 7.5 Electrical External power Supply 100-250 VAC, 50-60 Hz, 0.5 A Input voltage 5VDC 7.6 Mechanical Without antenna and power supply 13cm x 8.6cm x 3cm 7.7 Environmental Operating Temperature 0°C to 40°C Operating Humidity 5%-95% non condensing SU-I/ID Installation Manual 20 BreezeACCESS MMDS Series Specifications 7.8 Standards Compliance, General EMC FCC part 15, FCC part 21 Safety UL 1950 Environmental GR - 63 - CORE (Bellcore) BreezeACCESS/MMDS Series 21 SU-I/ID Installation Manual Appendix A APPENDIX A. AL 1 Lightning Arrestor The AL 1 Lightning Arrestor is used to protect transmitters and receivers from transients originating from lightning or EMP. The AL 1 is gas tube-based and is not radioactive. The gas discharge tube can sustain several transients if the time period between transients is sufficient to allow the tube to cool down. Figure A-1. AL-1 Connection Block Diagram One of the female-type N connectors is mounted directly through a hole in the shelter wall and held in place with a lockwasher and nut. SU-I/ID Installation Manual 22 BreezeACCESS MMDS Series Appendix A AL 1 Lightning Arrestor Specifications Turn on voltage 75V Insertion loss 0.3dB typical DC path from input to output existing Operating Temperature -55° C to +70° C Dimensions 67.5mm x 25mm x 25mm (2.7” x 1” x 1”) Connectors • Antenna Port: N-type, Female • Equipment Port: N-type, Female Operating Environment Indoor/Outdoor Grounding One of the female-type N connectors is mounted directly through a hole in the shelter wall and held in place with a lockwasher and nut. Note: All specifications are subject to change without notice. BreezeACCESS/MMDS Series 23 SU-I/ID Installation Manual Appendix B APPENDIX B. USING TELNET Use the following procedure to connect to BreezeACCESS units via a Telnet session. 1. Connect the PC to the Ethernet port of the unit (or the hub to which the unit is connected) using a straight Ethernet cable. If you connect the PC directly to a unit that is normally connected to a hub, use a crossed Ethernet cable. You may also connect the PC to any Ethernet port on the network and communicate with the unit to be managed via the wired or wireless media. 2. Make sure that the IP parameters of the PC are configured to enable connectivity with the unit. 3. Run a Telnet application and use the IP address of the unit to be managed as the Host Name. 4. Set Port to Telnet (this is the default). 5. Set Terminal Type to VT100 (this is the default). 6. Enter the Service Provider password. 7. When the password is recognized, the following message is displayed: You have entered. 8. Press Enter, the Breeze ACCESS Monitor is displayed on the screen. To exit the Telnet session, choose Disconnect from the Connect menu. (The session is terminated automatically, after a specific time of inactivity determined by the Log-out Timer). SU-I/ID Installation Manual 24 BreezeACCESS MMDS Series Appendix C APPENDIX C. MMDS CHANNELS AND FREQUENCIES Channel Name Frequency Band (MHz Low Frequency (MHz) High Frequency (MHz) Actual Value in Add/Delete Sub-bands menu Actual Value in Add/Delete Sub-bands menu A1 2500 - 2506 2501.5 2501 2504.5 2504 B1 2506 - 2512 2507.5 2507 2510.5 2510 A2 2512 - 2518 2513.5 2513 2516.5 2516 B2 2518 - 2524 2519.5 2519 2522.5 2522 A3 2524 - 2530 2525.5 2525 2528.5 2528 B3 2530 - 2536 2531.5 2531 2534.5 2534 A4 2536 - 2542 2537.5 2537 2540.5 2540 B4 2542 - 2548 2543.5 2543 2546.5 2546 C1 2548 - 2554 2549.5 2549 2552.5 2552 D1 2554 - 2560 2555.5 2555 2558.5 2558 C2 2560 - 2566 2561.5 2561 2564.5 2564 D2 2566 - 2572 2567.5 2567 2570.5 2570 C3 2572 - 2578 2573.5 2573 2576.5 2576 D3 2578 - 2584 2579.5 2579 2582.5 2582 C4 2584 - 2590 2585.5 2585 2588.5 2588 BreezeACCESS/MMDS Series 25 SU-I/ID Installation Manual Appendix C Channel Name Frequency Band (MHz Low Frequency (MHz) High Frequency (MHz) Actual Value in Add/Delete Sub-bands menu Actual Value in Add/Delete Sub-bands menu D4 2590 - 2596 2591.5 2591 2594.5 2594 E1 2596 - 2602 2597.5 2597 2600.5 2600 F1 2602 - 2608 2603.5 2603 2606.5 2606 E2 2608 - 2614 2609.5 2609 2612.5 2612 F2 2614 - 2620 2615.5 2615 2618.5 2618 E3 2620 - 2626 2621.5 2621 2624.5 2624 F3 2626 - 2632 2627.5 2627 2630.5 2630 E4 2632 - 2638 2633.5 2633 2636.5 2636 F4 2638 - 2644 2639.5 2639 2642.5 2642 G1 2644 - 2650 2645.5 2645 2648.5 2648 H1 2650 - 2656 2651.5 2651 2654.5 2654 G2 2656 - 2662 2657.5 2657 2660.5 2660 H2 2662 - 2668 2663.5 2663 2666.5 2666 G3 2668 - 2674 2669.5 2669 2672.5 2672 H3 2674 - 2680 2675.5 2675 2678.5 2678 G4 2680 - 2686 2681.5 2681 2684.5 2684 SU-I/ID Installation Manual 26 BreezeACCESS MMDS Series
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 1910:00:80 20:81:83 Producer : Acrobat Distiller 3.0 for Windows Modify Date : 2000:09:24 18:50:27-07:00 Page Count : 34EXIF Metadata provided by EXIF.tools