Amazon com Services 1459 3G Module User Manual and OEM installation manual
Gradys LLC 3G Module and OEM installation manual
User Manual and OEM installation manual
X1-Device User Manual/Specification HSDPA/WCDMA/EDGE/GPRS Data Module USER MANUAL / SPECIFICATION PN:63 PAGE2OF13 TITLE:;'(9,&( REV &RQWHQWV 5HYLVLRQ+LVWRU\ 2YHUYLHZ 5HFHLYH6SHFLILFDWLRQV ««««« 2.1 WCDMA/HSDPA «« 2.2 GSM / GPRS 7UDQVPLW6SHFLILFDWLRQV ««««««««««««««««««««««««« 3.1 WCDMA/HSDPA «««««««««««««««««««««««««« 3.2 GPRS / EDGE «««««««««««««««««««««««««« %DVHEDQG«««««««««««««««««««««««««««« 3,1'HVFULSWLRQV«««««««««««««««««««««««««««««««« 3,1&+$5$&7(5,67,&6 6.1 Power Management ««««««««««««««««««««««« 6.2 SIM Card Detection ««««««««««««««««««««««« 6.3 UART ««««««««««««««««««««««« 6.4 USB ««««««««««««««««««««««« 6.5 Host Wake & Interrupts ««««««««««««««««««««««« 0HFKDQLFDO,QWHUIDFH 7.1 SUPPLIER PART ««««««««««««««««««««««« 7.2 SUPPLIER PART – Complementary Part #1 (0.7mm stacking height) ««««« 7.3 Mechanical Drawings ««««««««««««««««««««««« 5)&RQQHFWRU6XSSOLHU3DUW «««««« 2(0,QVWDOODWLRQ,QVWUXFWLRQ USER MANUAL / SPECIFICATION TITLE:;'(9,&( PN:63 PAGE3OF13 REV 5(9,6,21+,6725< 5(9 (&2 1.0 &+$1*('(6&5,37,21 Initial release $33529('%< '$7( 09/08/10 Notes (unless otherwise specified): 1. All parts and materials must be ROHS compliant. FCC Regulations: zThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. zThis device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. zThe antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. zChanges or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. RF Exposure Information: This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. zThis device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. Maximum antenna gain allowed for use with this device is +2 dBi. When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text: &RQWDLQV7;)&&,';( 29(59,(: USER MANUAL / SPECIFICATION PN:63 PAGE4OF13 TITLE:;'(9,&( *(1(5$/63(&,),&$7,216 3$5$0(7(56 External Access Protocols Max Data Rate RX / TX Frequency Interval Max Output Power Operating Voltage GSM 850/900/1800/1900, GPRS/EDGE 3GPP TS 34.121 (WCDMA / HSDPA), 3GPP TS 51.010-1 (GSM/GPRS) HSDPA r5 3.6Mbps Down / 384 Kbps Up WCDMA 384 Kbps GPRS Multi slot class 10 – 48Kbps (Down / Up) EDGE 384 Kbps @ MSC9 (Down / Up) WCDMA / HSDPA 850 45 MHz WCDMA / HSDPA 1900 80 MHz WCDMA / HSDPA 2100 190 MHz GPRS / EDGE 850 45 MHz GPRS / EDGE 900 45 MHz GPRS / EDGE 1800 95 MHz GPRS / EDGE 1900 80 MHz WCDMA / HSDPA 23dBm (Power class: 3) GPRS 850 / 900 33dBm (Power class: 4) GPRS 1800 / 1900 30dBm (Power class: 1) EDGE 850 / 900 27dBm (Power class: E2) EDGE 1800 / 1900 26dBm (Power class: E2) VBATT 3.4V ~ 4.2V Rock Bottom [Sleep] WCDMA standby Current Consumption GPRS standby Peak Current Operating Temperature Range -10°C ~ +60°C Storage Temperature Range -30°C ~ +80°C Frequency Stability Physical Dimensions Weight '(6&5,37,216 WCDMA 850/1900/2100 0.75mA (Typical), 1.0mA (Max) 0.64s 1.28s 3.37mA 2.27mA 1.71mA 1.36mA 1.177s 2.98mA 1.69mA 1.8A ±80Hz WCDMA / HSDPA 2100 ±170Hz GSM / GPRS ±0.1ppm 0.2656 oz 5.12s 0.471s WCDMA / HSDPA 800 45.00 x 32.00 x 2.63mm 2.56s REV USER MANUAL / SPECIFICATION PN:63 PAGE5OF13 TITLE:;'(9,&( REV 5(&(,9(63(&,),&$7,216 :&'0$+6'3$ 3$5$0(7(56 Frequency Range Reference Sensitivity Level Adjacent Channel Selectivity Intermoduation Spurious Response In-Band Blocking Peak throughput '(6&5,37,216 WCDMA 2100 Down: 2110 ~ 2170 MHz WCDMA 1900 Down: 1930 ~ 1990 MHz WCDMA 850 Down: 869 ~ 894 MHz WCDMA 2100 -106.7dBm WCDMA 1900 -104.7dBm WCDMA 850 -104.7dBm WCDMA 2100 -92.7dBm WCDMA 1900 -90.7dBm WCDMA 850 -90.7dBm WCDMA 2100 -103.7dBm WCDMA 1900 -101.7dBm WCDMA 850 -101.7dBm WCDMA 2100 -103.7dBm WCDMA 1900 -101.7dBm WCDMA 850 -101.7dBm WCDMA 2100 -103.7dBm WCDMA 1900 -101.7dBm WCDMA 850 -101.7dBm HSDPA 33dB @ ±5MHz -46dBm ±10MHz, ±20MHz -44dBm -56dBm @ ±10MHz, -44dBm @ ±10MHz 3.6Mbps *60*356 3$5$0(7(56 Frequency Range '(6&5,37,216 GPRS / EDGE 850 Down: 869 ~ 894 MHz GPRS / EDGE 900 Down: 925 ~ 960 MHz GPRS / EDGE 1800 Down: 1805 ~ 1880 MHz GPRS / EDGE 1900 Down: 1930 ~ 1990 MHz Propagation Condition: Type of Channel BLER < 10%, Static PDTCH/CS-1 -102dBm GPRS 850/900/1800/1900 PDTCH/CS-2 -102dBm PDTCH/CS-3 -102dBm Minimum Input level for Reference Performance EDGE 850/900/1800/1900 PDTCH/CS-4 -102dBm PDTCH/CS-5 -99dBm PDTCH/MCS-5 -98dBm PDTCH/MCS-6 -96dBm PDTCH/MCS-7 -93dBm PDTCH/MCS-8 -90.5dBm PDTCH/MCS-9 -86dBm USER MANUAL / SPECIFICATION PN:63 PAGE6OF13 TITLE:;'(9,&( 75$160,763(&,),&$7,216 :&'0$+6'3$ 3$5$0(7(56 Frequency Range '(6&5,37,216 WCDMA 2100 Up: 1920 ~ 1980 MHz WCDMA 1900 Up: 1850 ~ 1910 MHz WCDMA 850 Up: 824 ~ 849 MHz Max Output Power 20.3 ~ 25.7dBm (Power Class III) Min Output Power Below -50dBm Spectrum Emission Mask Below -35dBc 2.5 ~ 3.5 MHz Offset 30KHz Below -35dBc 3.5 ~ 7.5 MHz Offset 1MHz Below -39dBc 7.5 ~ 8.5 MHz Offset 1MHz Below -49dBc 8.5 ~ 12.5 MHz Offset 1MHz Occupied Bandwidth Below 5MHz ACLR ±5MHz 33dB, ±10MHz 43dB *356('*( 3$5$0(7(56 Frequency Range Frequency error Phase error Modulation accuracy '(6&5,37,216 GPRS / EDGE 850 Up: 824 ~ 849 MHz GPRS / EDGE 900 Up: 880 ~ 915 MHz GPRS / EDGE 1800 Up: 1710 ~ 1785 MHz GPRS / EDGE 1900 Up: 1850 ~ 1910 MHz GPRS / EDGE GPRS EDGE GPRS / EDGE 850 / 900 Transmitter output power GPRS / EDGE 1800 / 1900 ±0.1ppm Peak phase error Below 20° RMS phase error Below 5° Peak EVM Less than 5% RMS EVM Less than 30% Power Level Output Power (dBm) 33 Tolerance (dBm) 31 ±3 29 ±3 27 ±3 25 ±3 10 23 ±3 11 21 ±3 12 19 ±3 13 17 ±3 14 15 ±3 15 13 ±3 16 11 ±5 Power Level Output Power (dBm) Tolerance (dBm) 30 ±2 28 ±3 26 ±3 24 ±3 22 ±3 20 ±3 18 ±3 REV USER MANUAL / SPECIFICATION PN:63 PAGE7OF13 TITLE:;'(9,&( 16 ±3 14 ±3 12 ±4 10 10 ±4 11 ±4 12 ±4 13 ±4 14 ±5 ±5 15 Power (dBm) ORFS @ Spectrum due to modulation ORFS @ Spectrum due to switching transient GSM / GPRS 850 / 900 REV Frequency offset (KHz) ±400 ±600 ±1200 ±1800 33 -19 -21 -21 -24 31 -21 -23 -23 -26 29 -23 -25 -25 -28 27 -23 -26 -27 -30 25 -23 -26 -29 -32 23 -23 -26 -31 -34 20 -23 -26 -32 -36 Power (dBm) Frequency offset (KHz) ±400 ±600 ±1200 ±1800 -22 -24 -24 -27 -23 -25 -26 -29 26 -23 -26 -28 -31 24 -23 -26 -30 -33 22 -23 -26 -31 -35 21 -23 -26 -32 -36 30 28 GSM / GPRS 1800 / 1900 USER MANUAL / SPECIFICATION TITLE:;'(9,&( %$6(%$1' Processors RISC CPU @ 230 MHz DSP @ 115 MHz Memory Multichip Package (MCP) contains both RAM & Flash 1GB NAND Flash 256MB (16MB x 16) DDR @ 92MHz Connectivity Full Speed USB UART JTAG (Debug Port) PN:63 PAGE8OF13 REV USER MANUAL / SPECIFICATION PN:63 PAGE9OF13 TITLE:;'(9,&( 3,1'(6&5,37,216 3,1 1DPH 'HVFULSWLRQ 3,1 1DPH 'HVFULSWLRQ GND Ground VBAT Battery GND Ground VBAT Battery GND Ground VBAT Battery GND Ground VBAT Battery GND Ground 10 VBAT Battery 11 GND Ground 12 VBAT Battery 13 GND Ground 14 VBAT Battery 15 GND Ground 16 VBAT Battery 17 GND Ground 18 VBAT Battery 19 NC No Connect 20 NC No Connect 21 PS_HOLD Power Supply Hold Up 22 UART_RXD Serial Receive 23 SIM_DETECT SIM card presence 24 UART_TXD Serial Transmit 25 GPIO2 Spare GPIO 26 UART_RTS Flow Control 27 GPIO3 Spare GPIO 28 UART_CTS Flow Control 29 GND Ground 30 JTAG_TDI Test Data In 31 USB_DM USB Data - 32 JTAG_TDO Test Data Out 33 USB_DP USB Data + 34 JTAG_TMS Test Mode Select 35 GND Ground 36 JTAG_TCK Test Clock 37 USB_EN USB Enable 38 JTAG_RTCK Return Clock 39 HOST_WAKE Host wake-up event 40 JTAG_TRST Test Reset + 41 H_M_INT Host to Modem Interrupt 42 JTAG_RESET_N Test Reset - 43 M_H_INT Modem to Host Interrupt 44 UIM_DATA SIM DATA 45 VBATT_EN Modem Power Enable 46 UIM_CLK SIM Clock 47 VREG_MSME 1.8V (Linear) 48 UIM_RESET SIM Reset 49 POWER_ON_OFF Modem ON/OFF 50 VREG_USIM SIM Voltage 51 GND Ground 52 GND Ground 53 GND Ground 54 GND Ground REV USER MANUAL / SPECIFICATION PN:63 PAGE10OF13 TITLE:;'(9,&( REV 3,1&+$5$&7(5,67,&6 3RZHU0DQDJHPHQW 3,1 1DPH 'LUHFWLRQ 9ROWDJH 'HVFULSWLRQ 21 PS_HOLD Modem Æ Host 1.8V Drive to 1.8V and hold for JTAG debug mode 49 POWER_ON_OFF Host Æ Modem 1.8V Pulling this pin LOW and holding for 500ms toggles power ON/OFF. 37 USB_EN Host Æ Modem 1.8V Enable/Disable USB PHY 45 VBATT_EN Host Æ Modem 1.8V Drive low to disconnect modem from the main battery POWER_ON_OFF application note: POWER_ON_OFF should be driven open collector on the host board. 6,0&DUG'HWHFWLRQ 3,1 23 1DPH SIM_DETECT 8$57 3,1 'LUHFWLRQ 9ROWDJH Host Æ Modem 'HVFULSWLRQ Software drives this pin HIGH. Hardware should pull it LOW when a SIM Card is inserted. 1.8V 1DPH 'LUHFWLRQ 22 UART_RXD Host Æ Modem 1.8V Receive Data 24 UART_TXD Modem Æ Host 1.8V Transmit Data 26 UART_RTS Reserve Reserve 28 UART_CTS Reserve Reserve 86% 3,1 9ROWDJH 'HVFULSWLRQ 1DPH 'LUHFWLRQ 9ROWDJH 'HVFULSWLRQ 31 USB_DM Bidirectional 1.8V USB Data - 33 USB_DP Bidirectional 1.8V USB Data + DEVICE supportsfull-speed USB only. The UART operates at 115,200 Baud with no Flow Control. +RVW:DNH ,QWHUUXSWV 3,1 1DPH 'LUHFWLRQ 9ROWDJH 'HVFULSWLRQ 39 HOST_WAKE Modem Æ Host 2.6V Signals the host device to wake from sleep mode when a TPH event has occurred. 41 H_M_INT Host Æ Modem 1.8V Host to Modem Interrupt 43 M_H_INT Modem Æ Host 1.8V Modem to Host Interrupt USER MANUAL / SPECIFICATION TITLE:;'(9,&( PN:63 PAGE11OF13 0(&+$1,&$/,17(5)$&( 6833/,(53DUW 6833/,(53DUW±&RPSOHPHQWDU\3DUW PPVWDFNLQJKHLJKW REV USER MANUAL / SPECIFICATION PN:63 PAGE12OF13 TITLE:;'(9,&( REV 0(&+$1,&$/'5$:,1*6 5)&211(&7256XSSOLHU3DUW OEM Installation Instruction This 3G Module has been authorized for mobile operation in North America. End user installation is not allowed. This module must be installed at factory by the host integrator and should not provide any instruction to the user on how to remove or install the module. This 3G module is approved to be used as a mobile device per FCC section 2.1091 and the antenna must be positioned in the host to provide at least 20 cm separation distance from user and nearby person. The following conditions must be met: 1. Maintain at least a 20 cm separation between the antenna and the user’s body. 2. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, maximum antenna gain (including cable loss) must not exceed 4dBi for Cellular and PCS band. 3. This 3G module must not be co-located or jointly operated with any other transmitter or antenna within the host device. 4. A label with the following statements must be attached to the host end product if the FCC ID label is not visible at the time of purchasing: Contains TX FCC ID: X8E-1459. 5. The host end product must include a user manual that clearly defines operating requirements and conditions that must be observed to ensure compliance with current FCC/IC RF exposure guidelines. 6. The host end product must also pass the FCC Part 15 unintentional emission testing requirement and be properly authorized per FCC Part 15. For portable devices, a separate approval is required to satisfy the SAR requirements of FCC Part 2.1093.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2010:11:04 10:20:08-07:00 Modify Date : 2010:11:04 14:02:55-07:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2010:11:04 14:02:55-07:00 Creator Tool : Adobe Acrobat Pro 9.4.0 Format : application/pdf Creator : Document ID : uuid:ae030ee2-6ec9-4295-bd4a-4a22888f7bd2 Instance ID : uuid:aade5104-a94e-40f1-819e-8c120ccfa36b Producer : Adobe Acrobat Pro 9.4.0 Page Count : 13 Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools