Amerec Steambath Generator Ak10 Users Manual X

W/K60 K60_OM

AK10 to the manual 5b43705c-463f-4a84-b8f7-49d2d29dae93

: Amerec Amerec-Steambath-Generator-Ak10-Users-Manual-507622 amerec-steambath-generator-ak10-users-manual-507622 amerec pdf

Open the PDF directly: View PDF .
Page Count: 4

Electric Shock Hazard - High voltage exists

within this equipment. There are no user

serviceable parts in this equipment. All

installation and service to this equipment

should be performed by qualified licensed

personnel.

Do not exceed 30 minutes in a steambath.

Excessive exposure can be harmful to your

health. Excessive exposure can produce a

rapid pulse, light-headedness, weakness

or fainting. If you become uncomfortable

or experience any of the above conditions

exit the steambath immediately.

Steambaths can put stress on the body.

Therefore a steambath should be used

only under a doctor's direction if you:

Are pregnant

Have a heart condition

Have high blood pressure

Have circulatory problems

Are under the influence of alcohol

Are under the influence of drugs

Have diabetes

Are under the care of a physician

Are in generally poor health

Children should only use the steambath

under close adult supervision.

Scald Hazard: Do Not Touch the steam

head or trim during operation as they are

HOT. Stay at least 12 inches away from the

hot steam escaping from the steam head.

Be careful when entering a steambath.

Escaping steam from an overheated steam

room may cause injury.

AMEREC STEAMBATH GENERATORS

(MODELS: AK5, AK7, AK10 w/K60 CONTROL)

FOR THE SAFETY OF YOU AND YOUR FAMILY PLEASE READ THE

WARNINGS TO THE RIGHT AND ALL INSTRUCTIONS BEFORE USING

YOUR STEAMBATH.

POST "STEAMBATH INSTRUCTIONS" LABEL OUTSIDE STEAMBATH

FOR SAFETY WARNINGS.

SAVE THIS MANUAL

Thank you for purchasing your new AMEREC steam generator. If we can be of any assistance

do not hesitate to call our Service Department at 1-800-331-0349.

WARNING

4209-24 12-09-02

AK Series w/K60 Control Owners Manual

4209-24 12-09-02

AK Series w/K60 Control Owners Manual page 2

SECTION 1A: STEAM GENERATOR OVERVIEW

SECTION 1B: STEAM GENERATOR OVERVIEW - CELSIUS AND 24 HOUR OPTIONS

The standard K60 model steam generator control

features an adjustable 60 minute time and tem-

perature control with digital display. The actual

room temperature and time remaining are alter-

nately displayed every 5 seconds. The primary

control can be mounted either inside or outside

the steam room and an optional secondary

control is available to mount in an alternate

location. The temperature can be adjusted in a

range between 100 degrees and 125 degrees

Fahrenheit with an initial default of 120 degrees.

Once the set temperature is reached the ''soft

steam'' feature automatically engages cutting

steam production back to a single element to

provide softer billowing steam during more of

the steam bath. If the steam room temperature

drops more than 5 degrees both elements will

automatically engage.

As an option your K60 control can be ordered

with a Celsius and/or 24 hour timer in place of the

Fahrenheit and 60 minute standard. The Celsius

option's adjustable temperature range is be-

tween 38 degrees and 52 degrees Celsius, with

an initial default of 49 degrees. The 24 hour timer

option is adjustable in 1 hour increments from 1

to 24 hours. Other features of the K60 control

should operate as described in section 2 below

with the above noted exceptions.

SECTION 2: OPERATION OF YOUR K60 CONTROL

1. Be sure the power circuit and water supply to

the generator are on.

2. Press the ON/OFF button on the control until

the temperature is displayed.

3. The generator should produce steam in 5 to 10

minutes and will turn off automatically in 60

minutes or less depending on the set time. The

control will alternately display time remaining

and the actual temperature at the sensor in your

steam room every 5 seconds.

4. To change the time setting press and hold the

TIME button on the control. Continuing to hold

the button will cause the time to increase in 5

minute increments from the prior setting. At 60

minutes the time setting will scroll backwards to

5 minutes. To shut down the generator press the

ON/OFF button.

5. To change the preset temperature setting

press and hold the TEMP button on the control.

While continuing to hold the button, the tempera-

ture display will increase in 1 degree increments

from the prior setting to 125 degrees Fahrenheit.

At 125 degrees Fahrenheit the temperature set-

ting will decrease in 1 degree increment to the

lowest setting, 100 degrees Fahrenheit.

6. The TIME and TEMP set points are remem-

bered by the K60 for your next bath unless power

to the steam generator is lost.

SECTION 3: TAKING A STEAMBATH

1. Wait for the steam room to reach a comfort-

able temperature.

2. Remove clothing and jewelry.

3. Enter the steam room and close the door to

prevent steam from escaping.

4. Relax and enjoy the warm steam releasing

tense muscles and refreshing the entire body.

5. If your steam room has a shower a pleasant

experience can be achieved by taking a warm

shower with the steam.

6. After a steambath a warm shower will give you

a feeling of relaxation and is conducive to a good

night’s rest. A cold shower will refresh you and

is a good way to start a busy day or prepare you

for an evening out.

SECTION 4: MAINTENANCE OF YOUR AK STEAM GENERATOR

SECTION 4: MAINTENANCE OF YOUR AK STEAM GENERATOR

The steam generator, steam head, fittings and

plumbing connections should be inspected regu-

larly for water leaks and damage. The AK steam

generator is equipped with a manual drain valve

for flushing sediments from the generator tank.

This procedure should be scheduled monthly or

more often depending on local water conditions

and steam bath usage.

Flushing Procedures:

1. The generator should be cool.

2. Press the control ON.

3. Open the manual drain valve.

4. The unit will drain without heating the water.

5. Allow the water to run for a full 10 minutes.

6. Push the control OFF. When the water stops

flowing out the drain, close the manual drain

valve.

4209-24 12/09/02

AK Series w/K60 Control Owners Manual page 3

SECTION 5: TROUBLE SHOOTING GUIDE

The troubleshooting guide is meant as a general aid only. There are no user serviceable parts in the generator. All repairs should be performed by a qualified service

person. For additional assistance or the factory authorized service person nearest you call: AMEREC's Service Department at 1-800-331-0349.

SYMPTOMS PROBABLE CAUSES ACTION TO BE TAKEN

Control won't turn "ON".

(Control light off).Improper power supplied (no power).

or

Control improperly connected.

or

Control cable is faulty.

or

Contol is faulty.

1. a. Make sure circuit breaker is "ON".

b. Using a voltmeter, check the voltage across the two fuses on the "PCA"

printed circuit assembly. Voltage should be 208V / 240V.

c. Check fuses, if the fuse(s) are blown, replace with Buss#

MDL 15/100 or equivalent fuse. If the fuse blows again - call AMEREC's

Service Department.

2. Check control(s) installed per Section 6-5 in the AK INSTALLATION AND

SERVICE INSTRUCTIONS.

3. Replace control cable - call AMEREC's Service Department.

4. Replace the control - Call AMEREC's Service Department.

Control "OFF".

Unit still makes steam.Generator is faulty.1. Turn off the circuit breaker.

2. Call AMEREC's Service Department.

Water runs out of steam head.Generator is faulty.1. Turn off the circuit breaker.

2. Turn off the water.

3. Call AMEREC's Service Department.

Steam room too hot or cold.Temperature adjustment needs setting.1. See Section 3, "Temperature Adjustment".

2. Call AMEREC's Service Department.

Control "ON".

K60 Control displays "E001". Temperature sensor not connected.1. Check that the sensor cable is connected to J4 on the PCA printed circuit

assembly.

2. Check the cable connection to the temperature sensor.

3. Replace sensor and/or cable - call AMEREC's Service Department.

Control "ON".

K60 Control displays "E002". Temperature sensor.

or

cable shorted.

1. Check sensor cable for damage from nail/staple puncture.

2. Check sensor cable ends for frayed/exposed wire strands.

3. Replace sensor and/or cable - call AMEREC's Service Department.

Control "ON".

K60 Control displays ">>>º". Steambath temperature over 132 º.

or

Sensor/cable is faulty.

1. If bath is too hot, shut off circuit breaker and call AMEREC's Service Department.

2. Treat as "E002" fault above.

Control won't turn "OFF".

(Control light on).Control is faulty.1. Replace the control - call AMEREC's Service Department.

Control "ON". (Control light on)

Unit won't steam.

Note: Time/Temp properly.

displayed on K60.

Unit has not filled completely.

or

Generator is faulty.

1. Wait at least 10 minutes after turning on the control.

2. Call AMEREC's Service Department.

Unable to adjust Time or Temp

setting with K60.Control is faulty.

or

Generator is faulty.

1. Replace control - call AMEREC's Service Department.

2. Replace PCA - call AMEREC's Service Department.

Sudden increases in rate water

sputters out of steam head.Foaming contaminants in the water

supply.1. Flush tank 3 times. See Section 4.

4209-24 12-09-02

AK Series w/K60 Control Owners Manual page 4

1

28

12

4

43

29

15

24

23

2

16

7

8

22

19

5

18

17

20

14

6

13

3

39

33

44

21

34

9

35

36

11

P.O. Box 2258, Woodinville WA 98072

425-951-1120 Fax: 425-951-1130

email address: amerec @ amerec .com