American Standard Lakeland 31 Large Single Bowl Sink 7173 001 Users Manual KITCHEN SINKS

2015-02-02

: American-Standard American-Standard-Lakeland-31-Large-Single-Bowl-Sink-7173-001-Users-Manual-416491 american-standard-lakeland-31-large-single-bowl-sink-7173-001-users-manual-416491 american-standard pdf

Open the PDF directly: View PDF PDF.
Page Count: 2

© 2003 American Standard Inc.
KS-53
Revised 3/03
LAKELAND™ 31”
LARGE SINGLE BOWL SINK
AMERICAST®
LAKELAND 31” LARGE SINGLE BOWL
KITCHEN SINK
• Americast®brand engineered material
• Single bowl design
• Self-rimming or undercounter installation
• Silicone sealant supplied
• Available in 1, 3,4 or 5 faucet hole configuration
Self-Rimming:
❏7173.001 Center hole only
❏ 7173.803 3 hole
❏7173.804 4 hole
❏7173.805 5 hole (Illustrated)
Undercounter Installation:
❏791123-100 Mounting Kit (consists of
cut-out templates and mounting clips
Nominal Dimensions: 787 x 559 x 241mm
(31" x 22" x 9-1/2")
Bowl sizes:
679mm (26-3/4") wide, 413mm (16-1/4") front to
back 229mm (9") deep
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See faucet section for additional models available
To Be Specified
❏Color:
❏Faucet*:
❏Faucet Finish:
❏Basket Strainer: 4331.013
❏Soap Dispenser: 4503.115, Color:
❏Trap:
Shown with 7230.152H Heritage Kitchen Faucet with
Cross handles (not included)
See reverse side for roughing-in dimensions
© 2003 American Standard Inc.
KS-54
LAKELAND™ 31”
LARGE SINGLE BOWL SINK
AMERICAST®
7173.001/803/4/5Self-Rimming
7173.001/803/4/5 Undercounter Mount
FINISHED WALL OR SPLASHBACK
FINISHED FLOOR
914mm
(36)
TO FINISHED
FLOOR (OPTIONAL)
●
*3/8 O.D. BENDABLE TUBING
COUNTERTOP
BY OTHERS SEALING
COMPOUND
FAUCET
RELIANT 4205.241
6270.000
TOP MOUNT
E
*
41mm(1-5/8)
559mm
(22)
787mm
(31)
394mm
(15-1/2)
213mm
(8-3/8)
203mm
(8)
229mm
(9)
13mm
(1/2)
146mm
(5-3/4)
51mm (2
OPTIONAL
7173.804
(4 HOLES)
7173.805
(5 HOLES)
SPRAY
38mm
(1-1/2)
RAD TYP.
89mm
(3-1/2)
DIA.
206mm
(8-1/8)
38mm
(1-1/2) DIA.
HOLES TYP.
102mm
(4)
HC
102mm
(4) 102mm
(4) 102mm
(4)
54mm
(2-1/8)
1-1/2 O.D. TAILPIECE
CUTOUT NOTE
254mm*
(10)
E
COUPLING NUTS
ON FITTING
NOTES:
TEMPLATE PROVIDED WITH MOUNTING KIT 791123-100 FOR UNDER-
COUNTER, INSTALLATION AND COUNTERTOP CUTOUT.
FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED AND
MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR WALL & COUNTERTOP SUP-
PORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided leaflet.
●
●
NOTES:
COUNTERTOP CUTOUT 756mm X 527mm WITH 25mm RADIUS (29-3/4
X 20-3/4 WITH 1” RADIUS)
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR WALL & COUNTERTOP
SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.4
These measurements are subject to change or cancellation. No responsi-
bility is assumed for use of superseded or voided leaflet.
DETAIL OF MOUNTING CLIP
(KIT No.791123-100)
BRASS
INSERT 13mm
(1/2)
MIN.
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
SINK
MOUNTING CLIP
(SEE DETAIL)
FINISHED WALL OR SPLASHBACK
FINISHED FLOOR
914mm
(36)
TO FINISHED
FLOOR (OPTIONAL)
●
*3/8 O.D. BENDABLE TUBING
FAUCET
RELIANT 4205.241
6270.000
TOP MOUNT
E
*
41mm(1-5/8)
559mm
(22)
787mm
(31)
394mm
(15-1/2)
213mm
(8-3/8)
203mm
(8)
241mm
(9-1/2)
13mm
(1/2)
146mm
(5-3/4)
51mm (2
OPTIONAL
7173.804
(4 HOLES)
7173.805
(5 HOLES)
SPRAY
38mm
(1-1/2)
RAD TYP.
89mm
(3-1/2)
DIA.
206mm
(8-1/8)
38mm
(1-1/2) DIA.
HOLES TYP.
102mm
(4)
HC
102mm
(4) 102mm
(4) 102mm
(4)
54mm
(2-1/8)
1-1/2 O.D. TAILPIECE
CUTOUT NOTE
254mm*
(10)
E
COUPLING NUTS
ON FITTING
COUNTERTOP
BY OTHERS SEALING
COMPOUND

Navigation menu