Amjeon Precision Optics OPTICAM CMOS Camera User Manual K9173 OptiCAM II

Download:
Mirror Download [FCC.gov]
Document ID	271406
Application ID	aR8qoK2o4mm0pzU6g9B94w==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	31.23kB (390429 bits)
Date Submitted	2002-09-18 00:00:00
Date Available	2002-09-18 00:00:00
Creation Date	2002-09-10 15:25:34
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2002-09-10 15:47:35
Document Title	Microsoft Word - K9173_OptiCAM_II.doc
Document Creator	PSCRIPT.DRV Version 4.0

OptiCAM™ Introduction
OptiCAM™ is a high-resolution security camera
capable of transmitting 60 frame per second video
through standard Category 5 cable using RJ45
connectors.
OptiCAM™ RJ45 CMOS Camera
OptiCAM™ uses a high quality CMOS image
sensor, and its compact size enables it to be
mounted on table, wall, or ceiling. All signal and
power is carried by one cable, with no external
power supply required – making for fast and
convenient installation.
x Never face OptiCAM™ towards the sun, even
when not in use! Use caution when operating in
the vicinity of spotlights or other bright lights
and light reflecting objects.
x Do not operate OptiCAM™ beyond its
temperature, humidity or power supply ratings.
Use the camera under conditions where
temperatures are within –5°C to +45°C, and
relative humidity is below 80% (non
condensing).
ADEMCO reserves the right to change details and
specifications without prior notice.
3. Select the appropriate mounting screw
holes, then secure the bracket to the
mounting surface.
4. Connect the RJ-45 connector to the socket
on the rear of the camera body as shown.
5. If using left or right cabling, remove the
appropriate knockout on the camera body
and route the cable.
Selecting Mounting Location
OptiCAM™ may be mounted on tabletop, wall or
ceiling. Choose a location that:
x Provides the desired coverage area,
x Can be reached with a RJ-45 connection, and
x Does not exceed environmental ranges.
Important Safeguards and Warnings
Prior to installation and use of this product,
observe the following safeguards and warnings:
x Only operate this unit in accordance with these
instructions!
x Always observe proper polarity, and be sure to
use a regulated 12VDC power source! Failure
to observe power specifications will void the
factory warranty.
x Do not attempt to service the product, as there
are no user-serviceable parts inside. Refer
servicing to qualified service personnel.
x Refer to the instructions for installation and
removing camera components.
x Handle OptiCAM™ with care. Improper
handling or storage could damage the camera.
x Do not expose OptiCAM™ to moisture, or try to
operate it in wet areas. Should OptiCAM™a
become wet, immediately turn power off and
refer servicing to qualified personnel.
Installation
To install the camera:
1. Separate the bracket from the camera body.
2. Select the desired cable routing (left, right,
top, or back). If using top or back wiring,
punch out the appropriate knockout on the
bracket, then route the cable through the
bracket.
6. Snap the camera body into the bracket and
adjust for proper coverage area.
Sun Shield Installation
If desired, snap the Sun Shield (supplied) over
the lens to prevent unwanted glare from
entering OptiCAM™.
®
165 Eileen Way, Syosset, New York 11791
OptiCAM™ Specifications
OptiCAM™ RJ45 CMOS Camera
Signal Format
Scanning System
Scanning Freq.
Image Sensor
Number of Pixels
Image Area
White Balance
Exposure
Gamma Correction
Signal/Noise Ratio
Auto Elect. Exposure
Min. Illumination
Fixed Pattern Noise
Sensitivity
Video Output
Lens Type
Supply Voltage
Operating Current
Operating Temperature
Storage Temperature
Operating Humidity
Dimensions
NTSC
2:1 Interlacing
H: 15.734 kHz
V: 59.94 Hz
1/3 Inch CMOS
510 x 492
4.69 x 3.54 mm
Automatic
Automatic
0.5
Over 40 dB
1/60 ~1/5000 sec
< 3 lux @f1.4
< 0.03% Vp-p
< 0.3 lux /f1.2 (3000K)
Composite: 1.0Vp-p/75
ohm
3.6 mm normal type
(V36092IG4)
DC +12V (+/- 20%)
< 300mW
0° – 40° C
-40° – 125°C
< RH 80%
32 x 32 mm
OptiCAM™ Lens Specifications
Sensing Area (inches)
Full Field Angle
Optical Distortion
TV distortion
Focal Length
Back focal length
Flange back length
f/#
Iris
Focus Extension
Diameter (Thread)
Length
Lens Construction
¬.l
K9173 9/02
1/3 inch
92°
-28.24%
-13.97%
3.6 mm
6.26 mm
5.96 mm
f2.0
Fixed
OptiCAM™ Cable Specification
RJ45 (External System)
+12VDC
Blue/White
+12VDC
Blue
Audio (not used)
NC
Gnd
Brown
Video
Orange
Gnd
Brown/White
NC
NC
NC
NC
OptiCAM™ Limited Warranty
Alarm Device Manufacturing Company, a Division of Pittway
Corporation, and its divisions, subsidiaries and affiliates
("Seller"), 165 Eileen Way, Syosset, New York 11791,
warrants its products to be in conformance with its own plans
and specifications and to be free from defects in materials and
workmanship under normal use and service for 36 months
from date of manufacture unless the installation instructions or
catalog sets forth a shorter period, in which case the shorter
period shall apply. Seller's obligation shall be limited to
repairing or replacing, at its option, free of charge for materials
or labor, any product which is proved not in compliance with
Seller's specifications or proves defective in materials or
workmanship under normal use and service. Seller shall have
no obligation under this Limited Warranty or otherwise if the
product is altered or improperly repaired or serviced by
anyone other than Ademco factory service. For warranty
service, return product transportation prepaid, to ADEMCO
Factory Service, 170 Michael Drive, Syosset, New York
11791.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED,
OF MERCHANTABILITY, OR FITNESS FOR A
PARTICULAR PURPOSE OR OTHERWISE, WHICH
EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO
ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY
OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE
LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN
NEGLIGENCE OR FAULT.
50 cm ~ f
M12 x 0.5 pitch
15.13 mm
5 elements
®
165 Eileen Way, Syosset, New York 11791

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2002:09:10 15:25:34
Producer                        : Acrobat Distiller 4.05 for Windows
Creator                         : PSCRIPT.DRV Version 4.0
Title                           : Microsoft Word - K9173_OptiCAM_II.doc
Modify Date                     : 2002:09:10 15:47:35-04:00
Page Count                      : 2

EXIF Metadata provided by EXIF.tools