Amtelco 258A008 H.110 Basic Rate Interface ISDN User Manual users manual

Download:
Mirror Download [FCC.gov]
Document ID	121652
Application ID	LstBMO62TW2MGCiyG5BnOQ==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	3.32kB (41473 bits)
Date Submitted	2000-10-19 00:00:00
Date Available	2000-11-02 00:00:00
Creation Date	2000-10-19 08:24:30
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2000-10-19 08:24:31
Document Title	users manual

Infinity Series H.110
Basic Rate ISDN Board
INSTALLATION INSTRUCTIONS
Documentation Revision 0.3: June 7, 2000
Copyright © 2000
by American Tel-A-Systems, Inc.
All rights reserved.
258M001
Quick Start • 2-1 •
The H.110 Basic Rate ISDN Board
2.0 Quick Start
This section describes the first steps you should perform to determine if your
Infinity Series H.110 Basic Rate ISDN Board is communicating correctly with
your CompactPCI system. You can perform this quick check without connecting
any cables. The exact procedure will vary depending on which operating system
you are running. For each operating systems, drivers are required to interface to
the boards. The drivers supplied by Amtelco have tests built into them to verify
communications with the boards. These drivers also come supplied with utility
programs that allow the developer to test communications with the board. Please
consult the appropriate documentation for the driver and operating system you
are using.
Quick Start Procedure
1. With the chassis power off, insert the board into a slot.
2. Turn on the computer.
3. If the Amtelco driver is not already installed, install it now, following the
instructions supplied with the driver.
4. Most Amtelco drivers will display a list of boards that are installed (see the
documentation for the particular driver that you are using). If the H.110 Basic
Rate ISDN Board is listed, skip to step 6.
5. If the board is not listed, there may be a problem with the board not being
seated correctly in the backplane. There may also be a problem with a memory
or interrupt conflict. Power down the chassis and check that the board is properly
seated
Quick Start • 2-2 •
The H.110 Basic Rate ISDN Board
in the connector and repeat steps 1-4. If this does not remedy the problem, try
removing any other computer telephony boards in the system. If your chassis is
unable to find the board, consult the number at the end of this section.
6. Run the program “xdsutil” supplied with the driver. Send the message “IN” to
the H.110 Basic Rate ISDN Board. The board should respond with the message
“IA”.
7. Send the message “VC” to the board. Verify that the Receive Message reads:
VCxxxxvvvvHBN (where xxxxvvvv is a variable indicating the firmware
version).
8. If the Communications screen shows the correct command responses, your
H.110 Basic Rate ISDN Board is communicating with the host. You may now
power down the computer and attach the necessary cables (see section 3.4) For
technical assistance, call Amtelco at 1-608-838-4194 ext.168.
Installation • 3-1 •
The H.110 Basic Rate ISDN Board
Figure 2: Location of Jumpers, Headers, and Connectors
3.0 Installation
This section describes how to install your Infinity Series H.110 Basic Rate ISDN
Board into your computer and how to use the jumpers, headers, and connectors.
Before you begin the installation procedure, be sure to test the board as
described in section 2.0 (Quick Start).
Installation • 3-2 •
The H.110 Basic Rate ISDN Board
The Infinity Series H.110 Basic Rate ISDN Board actually consists of two boards.
The front board which contains the processor, DSP’s, switching, HDLC
controllers, and logic. The rear board contains the interface and connectors to
the Basic Rate Interface ports.
3.1 PCI Configuration
As Infinity Series boards conform to the PCI standards, there are no switches to
set to configure the H.110 BRI Board's memory address, I/O addresses, or
interrupt. The host processor’s bios will automatically configure the board at boot
time to avoid conflicts with other boards in the system.
3.2 Jumpers & Headers for the Front Board
The following is a complete list of all jumpers for the H.110 BRI ISDN Board:
JW1-1 Firmware Select. If firmware has been downloaded to the board, this
jumper selects whether the downloaded firmware or the factory default firmware
is used. When this jumper is installed, the factory default firmware is executed
whenever the board is reset. When the jumper is not installed, the downloaded
firmware will be executed after a reset if it is present. If no downloaded firmware
is present, the factory default firmware is executed after reset.
JW1-2 DSP Firmware Select. Two separate firmware programs are included in
the EAROM, one for the board processor and one for the DSP. If JW1-2 is
installed and downloaded DSP firmware is present, the factory DSP firmware is
executed after reset. Otherwise, the downloaded firmware is executed if present.
See JW1-1.
Installation • 3-3 •
The H.110 Basic Rate ISDN Board
JW1-3 Undefined, reserved for future use.
JW1-4 Undefined, reserved for future use.
P3 Diagnostic port. Never install jumpers here.
P4 This header is used for programming internal logic and should never be
jumpered.
3.3 Connectors: J7, J8, & J9
J7 This connector is used for the installation of a mezzanine board.
J8 This connector is used for the installation of a mezzanine board.
J9 This connector is used for the installation of a mezzanine board.
3.4 Jumpers & Connectors for the Rear Board
J1 Basic Rate ISDN Connections for port 0-15. This connector is a 68 pin SCSI-3
type connector. It contains two pairs for each Basic Rate ISDN port or interface
on the board. See Figure 3.
J2 Basic Rate ISDN Connections for ports 16-31. This connector is a 68 pin
SCSI-3 type connector. It contains two pairs for each Basic Rate ISDN port or
interface on the board. See Figure 3.
JW1-8 These jumpers terminate the individual BRI ports. Termination is required
if the port is to be used as an NT (network termination) or if it the last or only TE
(terminal
Installation • 3-4 •
The H.110 Basic Rate ISDN Board
Figure 3: J1 & J2 Pin Assignments equipment) on the interface. The jumpers
should be installed when termination is required. Each port requires two jumpers
with port 0 using the first pair of jumpers on JW1, and port 31 using the last pair
of jumpers on JW8.
3.4 Installation
To install the H.110 BRI ISDN Board in your system:
1. Do not connect the board to the PSTN. Follow the quick check procedures
described in section 2.0.
2. If the quick check is successful, turn off the chassis power and remove the
board from the chassis.
3. Install any necessary board jumpers. See section 3.2 for jumper
configurations.
Installation • 3-5 •
The H.110 Basic Rate ISDN Board
Figure 4: Installing Cables on J1 and J2
4. Reinsert the front board into the chassis. Seat it properly in a slot in the
chassis and secure it with the front panel handles. Do not connect the board to
the PSTN.
5. Insert the rear board into the corresponding slot on the rear panel.
6. Connect the host chassis to the mains supply using a socket-outlet with
protective earthing connection and connect any additional protective earthing
used.
7. Connect the telephone cables to J1 & J2. The telephone cable terminates in a
68 pin SCSI-3 male connector. Secure with mounting screws. If it is
subsequently desired to open the host equipment chassis for any reason, the
PSTN cable must be detached prior to effecting access to any internal parts
which may carry telecommunications network voltages.
Installation • 3-6 •
The H.110 Basic Rate ISDN Board
3.5 Hot Swapping a Board
The Infinity Series H.110 Basic Rate ISDN Board can be “hot swapped, that is it
can be removed from a functioning system without turning the power off or
interrupting applications. However, to be able to do this, the host processor must
be equipped with suitable hot swap drivers as well as a hot swap manager which
will alert applications when a board has been inserted or removed from the
system so that resources can be properly managed. It is beyond the scope of this
manual to describe the operation of either the hot swap driver or hot swap
manager. Each H.110 board is equipped with a switch linked to the lower ejector
tab and a blue LED. This combination is used to coordinate the actions of an
operator with the system software. When inserting a board, the board is pushed
in part of the way until the blue LED is illuminated. The insertion may then be
completed. When the connection process is complete, the LED will go out. To
remove a board, the lower ejector handle is depressed until it is in the unlatched
position. When the blue LED comes on, the board may be removed from the
system.
The rear board MUST ALWAYS be inserted BEFORE the front board, and
removed AFTER the front board.
To install the front board in a system under power:
1. Insert the board with the ejector tabs spread apart until partially engaged.
2. Wait until the blue LED is illuminated.
3. Finish inserting the board by pushing the ejector tabs towards each other. The
LED should then go out.
Installation • 3-7 •
The H.110 Basic Rate ISDN Board
To remove the front board from a system under power:
1. Depress the lower ejector tab until it is in the unlatched position.
2. Wait until the blue LED is illuminated.
3. Finish removing the board by spreading the ejector tabs apart until the board is
ejected.
To insert the rear panel board into a system under power:
1. The rear board should be disconnected from the PSTN. Make sure there is no
board in the corresponding front panel slot.
2. Insert the rear board.
3. Connect the telephone cables to J1 & J2. The telephone cable terminates in a
68 pin SCSI-3 male connector. Secure with mounting screws.
4. Insert the front board as described above.
To remove a rear panel board from a system under power:
1. Remove the front board as described above.
2. Disconnect the PSTN cables from J1 and J2.
3. Remove the rear board from the system.
Installation • 3-8 •
The H.110 Basic Rate ISDN Board
Figure 6: Front Panel with Aux and Hot Swap LED and top and bottom ejector
handles

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2000:10:19 08:24:30
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2000:10:19 08:24:31-04:00
Page Count                      : 6

EXIF Metadata provided by EXIF.tools