Andover Audio AALPA01 RECORD PLAYER User Manual 7 23 12
Andover Audio LLC RECORD PLAYER 7 23 12
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3970027 |
| Application ID | OoniV/nEBMOloeeaHp1txA== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 372.93kB (4661681 bits) |
| Date Submitted | 2018-08-20 00:00:00 |
| Date Available | 2018-08-20 00:00:00 |
| Creation Date | 2018-07-23 18:21:32 |
| Producing Software | Corel PDF Engine Version 15.0.0.486 |
| Document Lastmod | 2018-07-23 18:21:32 |
| Document Title | 7-23-12 |
| Document Creator | CorelDRAW X5 |
| Document Author: | Administrator |
OWNER’S MANUAL
THE+RECORD PLAYER
Integrated High Fidelity Turntable System
+AUD|O
www.p|usaudio.com
Page 2
Table of Contents
Warnings / FCC Statement .................................................. 4-5
Introduction / About/ In the Box 6
Placement,“
Front Panel,“
Remote Control
Back Panel
Setup Guide11-12
Bluetooth 8: Playback to/from a PC ttttttttttttttttttttttttttttttttttttttttttttttttttttttttt 13
Vinyl Care14
Guarantee / Product Cleaning15
Specifications ......................................................... 16
Contact / Disclaimer ......................................................... 17
Page 3
DO NOT OPEN
TO PREVENT THE RISK OF EI ECTRIC
SHOCK, DO NO REMOVE COVER NO
USE ERVICEABLE PARTS INSIDE,
RhI-hR SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol alerts the user to the presence of
uninrutetea ”darigcrousvoltage" within the
preauei'r enrlosure that may be uisumnent
magnitude to constitute a risk ofeleum‘ slka to
persons
important Safety Instructions
This symbol is intended to aim the user It) the
prescm‘e at imparrant operiring arid maintcnance
(seruringi instructions in the literature
aewmpanying the applinnie
been dropped
1, Read these instructions. 14. Do not expose this apparatus to drips or splashes,
2, Keep these instructions. 15. The apparatus shall not be exposed to dripping or
3 Heed all warnings. splashing and that no objects filled with liquids, such
4 Follow all warnings. as vases, shall he placed on the apparatus
5 Do not use this apparatus near waler. 16. Do not install this apparatus iii a book case or similar
6. Clean only with dry cloth. unit.
7, Do not block any ventilation openings Install in 17. The apparatus draws nominal non-operating power
accordance with the manufacturer’s instructions from the AC outlet With its STANDBY/ON switch in
8, Do not install near any heat sources such as radiators, the standby position
heat registers. stoves, or other apparatus (including 18. The apparatus should be located close enough to the
amplifiers) that product heat, AC outlet so that you can easily grasp the power cord
9 Do not defeat the safety purpose of the polarized or plug at any time.
groundingrty'pe plug. A polarized plug has two blades 19. To completely disconnect the power input, the rear
With one wider than the other A grounding type plug panel power switch may be swuched off.
has two blades and a third grounding prong. The wide 20. Excesswe sound pressure from earphones and head-
blade or the third prong are provided for your safety, phones can cause hearing loss.
lfthe provided plug does not fit into your outlet, 21. The battery shall not be exposed to excessive heat such
consult an electrician for replacement of the obsolete as sunshine, fire or the like.
outlet.
10. Only use attachments/ accessories specified by the
manufacturer.
11. Use only With the cart, stand, tripod, bracket or table
specified by the manufacturer. or sold with the appae ®
ratus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tiprover
12. Unplug this apparatus during lighting storms or when
used for long periods oftime.
13. Refer all serVicing to qualified serVice personnel, Sere
vicing is required when the apparatus has been dame
aged in any way. such as power supply cord or plug is
damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
Page 4
Additional Safety Advice
1, Keep surrounding objects at least four inches away
from the apparatus for adequate yentdation
Ventilation openings on the apparatus should not be
impeded by such items as newspaper. cloths, Curtains.
and the likc,
3 Do not place naked flame sources near the apparatus,
such as lighted candles
4. Dispose of internal dectronics in accordance With
local safety and environmental regulations
5. Do not operate the apparatus at a temperature less
than 36 F / 2 C or greater than too F / 38 C
Caution
- DO NOT REMOVE THI: EXTERNAL ENCLOSURE
PARTS TO EXI’OSE THE ELECTRONICS NO USER
SERVICEABLF. PARTS ARE INSIDE
0 IF YOU ARE EXPERIENCING PROBLEMS \VITII
THIS PRODUCT, CONTACT PLUS AUDIO CUSV
TOMER SUPPORT. DO NOT USE THE PRODUCT
UNTIL IT HAS BEEN REPAIRED.
FCC STATEMENT FOR THE U.S.A.
This equipment has been tested and found to
comply with the limits tor a Class B digital device,
pursuant to Part15 ofthe FCC Rules These limits
are designed to prowde reasonable protection
against harmful interference in a reSidential
installation, This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that Interference Will not occur in a
particularinstallalion
If this equipment does cause harmful interference to
radio crtelevision reception, which can be
determined by turning the equipment offand on, the
user is encouraged to try to correct the interference
by one or more ofthe following measures:
-- Reorient or relocate the receiving antenna.
-- lncrease the separation between the equipment
and receiver
,, Connectthe equipment into an outlet on a circuit
differentfrom that to which the receiveris
connected,
w Consult the dealeroran experienced radio/TV
technicianfor help
Caution:
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment
Caution
Changes or modification to this cquipmcnl not expre ‘Vly
approved by +AUDID for compliance wrll Void the user's
warranty.
This product can be recycled pruducts hearing this symbol
must NOT be thrown away With normal household waste.
At the end or the product’s life, take it to a collection Point
designated for recycling of electrical and electronic devices.
Find out more about return and collection points through
your local authority
The European Waste Electrical and Electronic Equipment
(WEEE) Directive was implemented to dramatically reduce
the amount of waste going to landfills, thereby reducing the
envuonmental impact on the planet and on human health.
Please act responsibly by recycling used products it this
product is still usable, consider giying it away or selling it,
ISED Compliance Statement:
This device contains licence-exempttransmitter(s)lreceiver(s)
that comply with Innovation, Science and Economic
Development Canada's licence-exempt RSS(s), Operation is
subject to the followmg two conditions:
1. This device may not cause interference,
2 This device must accept any interference, including
interference that may cause undesired operation of the device
L‘emetteur/recepteur exempt de licence contenu dans le present
appareil est conforme aux CNR d’lnnovation, Sciences et
Developpement economidue Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisee aux deux
conditions suivantes
1. L’appareil ne doit pas produire de brouillage;
2. L’apparell doit acceptertout broulllage radioelectrique subi.
meme si le brouillage est susceptible d’en compromettre le
fonctionnement
This equipment complies with IC RSS—102 radiation exposure
limits set forth foran uncontrolled environment, This transmitter
must not be co-located oroperating in conjunction with any other
antenna ortransmitter.
ce materiel est conforme aux limites de dose d'exposition aux
rayonnements ic rssetoz énoncees pour un autre
envrronnementcet émetteur ne doit pas étre situées ou operant
conlointement avec toute autre antenne ou l'emetteur,
Page 5
THE+RECORD PLAYER Instructions
Thank you for purchasing THE+RECORD PLAYER, a product that epitomizes the
+AUDIO philosophy of delivering superb sound quality in a longelasting form that’s
both easy on the eyes and remarkably simple to use. With the proper care and operation,
THE+RECORD PLAYER will provide many years of trouble-free enjoyment.
To get the most from your product, be sure to thoroughly review this manual and heed the
important safety instructions. If you have any questions not covered here please contact
your local +AUDIO customer support by phone or email.
Please save the carton and original packaging in case you ever need to move or ship your
unit.
About +AUDIO
Comprised of passionate music lovers and professionals who span design, engineering,
manufacturing and distribution, +AUDIO creates high-performance entertainment
products that deliver a magnificent HiFi experience from elegantly designed, compact
enclosures.
Unlike some other audio companies who simply place their name on off-the-shclf
products, +AUDIO designs and engineers its audio products from the ground up,
with the finest parts, materials and components sourced from a handpicked group of
manufacturers that meet exacting quality standards. The result is durable products
designed for your continued musical enjoyment.
In the Box
- THE+RECORD PLAYER - Operational Manual
. Dustcover . ProeIect Turntable Manual
. Setup Guide . Tonearm Counterweight
. IR Remote Control . Anti-Skate Weight
- AC Power Cord - 7” Single Adapter
- Platter with Felt Mat - Belt
. Phono Cartridge
Page 6
Placement
As with any sound system, placement within your room will afiect how effectively the
sound fills the space. THE+RECORD PLAYER features a 2707degree sound field to
provide a spacious, roomeenveloping performance. Following a few simple guidelines will
result in the most enjoyable sound quality.
. To assure the most even sound coverage, try to place THE+RECORD PLAYER
near the center of one ofthe walls, at, or slightly below ear height for a seated
listener.
. Ifthe unit will be placed in a corner, angle it at 457degrees so that one side is not
blocked.
. Try to avoid placing the unit in an enclosed bookshelf or cabinet as this will
significantly compromise its performance.
. Keep the sides ofthe unit unobstructed by solid objects for as much distance as
practical, but at least 12” (~30.5 cm).
. Place the unit on a solid table or component rack, DO NOT use soft vibration
isolators or place the unit on a carpet or foam. If the surface is not sufficiently
rigid, acoustic feedback will result.
Page 7
Front Panel
+AUJIO
e) .c w. W» M m Wu): 0
Top portion:
IR Remote Receiver (behind logo).
LED baregraph indicating relative volume. The LED's will illuminate during
volume adjustment and will extinguish approximately Seseconds after
adjustment is complete
Status LED’s indicating Power ON, Selected Source, Turntable Speed, and
Listening Mode.
Bottom portion (from left to right):
0) Press to WAKE from Standby. Short press (<3 sec.) to MUTE.
Long press (>3 sec.) to enter STANDBY.
Short press to select source (except Bluetooth). Long press when PHONO is
{)3 the source to change speed (33-1/3 or 45RPM). The PHONO LED indicator
will turn GREEN to indicate 45RPM speed.
— + Decrease (7) or increase (+) volume by approximately ZdB per step,
m Press to scroll through listening modes: STEREO (LED off) / WIDE (white
LED) / MONO (red LED).
9 Press for Bluetooth. To exit Bluetooth press the source select button.
AUX: Duplicates the function of the Rear Panel AUX input jacks, When a
plug is inserted into this jack, the rear panel phono jacks are overridden.
m HEADPHONE: Plugging headphones into this jack will power headphones
I I and turn off the internal speakers and preamp output,
Page 8
Remote Control
+AU3I0
Batters; Only
'lhe remote control buttons duplicate those found on the front panel and operate exactly
as previously described with one exception: Pressing and holding the remote source select
button will not change the turntable speed like it does on the front panel.
When necessary, replace the remote control battery with model CR2032 only.
Page 9
Back Panel
© THE+RECORD PLAYER
sum evvlem mm m a»; Wm
ug— W cm 9mm
©ng 00 {3o
“GO
©
PC (USE-Mini B): Use a USB-Mini B to USB-A cable to connect to your computer for
recording or file playback.
5V (USB-A): Power your mobile device or Google Cast audio or Amazon Echo WiFi
audio adapter.
TOSLINK OPTICAL DIGITAL INPUT: Accept SPDIF or PCM audio from an optical
connection, such as a TV, Apple Airport Express or similar device.
LINE IN ( 1/ 8” input): Connect a line level audio source or WiFi audio adapter. This input
has auto signal sensing that will wake the unit from standby and switch to this input when
an audio signal is present.
AUX IN (RCA input): Connect an external audio device, such as a CD player or a radio
Tuner,
PRE-OUT (Preamp output): Output an unamplified signal to an external amplifier, a set
of powered speakers, or a subwoofer.
INTERNAL SPEAKER SWITCH: Turn the internal speakers on or off.
POWER INLET CONNECTOR: Plug the female end of the supplied cable here, and the
male side into a mains power outlet.
POWER SWITCH: Press the top ofthe switch to turn on the unit. Turn OFF ifyou plan
on leaving the unit unused for an extended period of time. The unit will draw minimal
power during standby, so this switch may normally be left on.
Page 10
THE+RECORD PLAYER Setup Guide
Motor Serew'
9 Thumb Screw
Spea key Base
Flatter mat
Platter
up, 7 7/
STEP 1: Remove the TWO motor screws
from the turntable with a screwdriver. US/
CAN customers: remove the TWO large
thumb screws. Save all screws and install
them whenever shipping or moving the unit
a great distance, or damage may occur.
STEP 2: Install the drive belt by stretching
it around the inner platter and over the “top
step” of the small motor pully. US/CAN
customers: skip to Step 4(b).
STEP 3: Place the turntable against the
speaker base with one hand, Use the other
hand to connect the turntable RCAs (Red/
White) to the bases corresponding RCA
input port; similarly, connect the turntable
power plug to the power connector port.
STEP 4: (a) Lower the turntable fully into
the base, nestling the turntable feet into
the corresponding foot cutouts in the
speaker base. (b) Ensure the turntable plinth
(platform) does not touch the inner wall
ofthe speaker base (by 1/4" / 6 mm), or
acoustic feedback may result during vinyl
record playback. With two hands, gently
place the platter on the spindle, followed by
the felt platter mat.
Page 11
THE+RECORD PLAYER Setup Guide (Continued)
Anti-SkateWive Loop Anti-Skating Stub (white line)
‘, _____
counterweight
'Toneavm Lift Levev(in high positionl
Camidge
(Red 2M shown) Toneavm
StylusGuavd
Toneavm Rest
STEP 5 - TONEARM BALANCING: Install the counterweight by pushing it carefully
onto the rear of the tonearm. You may remove the stylus guard from the cartridge. With
the tonearm lift lever in the lower position, move the tonearm from its rest and carefully
rotate the counterweight until the tonearm tube balances such that it floats level. Once the
tonearm is correctly balanced, return it to the tonearm rest position.
am ofcounterweight
"Downforce scale ring (in grams)
+Downfovee
STEP 6 - COUNTERWEIGHT: Use one hand to hold the back of the counterweight
without moving it. and use the other hand to gently revolve the downforce scale ring
until the zero (0.0g) is vertical in line with the antieskating stub (marked by a white line
on the back of the tonearm). Next, rotate the counterweight and downforce scale ring as
one, counter-clockwise (as seen from the front) to adjust the downforce according to the
cartridge manufacturer’s recommendations using the numbers on the downforce scale
ring:
. OM10 cartridge: set the force to 1.8g ijf‘ Gmovez ‘mmwnl'znf WWW?“
. 2m Red cartridge: set the force to 2.0g
omo
Cartridge
Setup (ex)
STEP 7 - ANTI-SKATE: To set the anti-skate
force, carefully hang the anti-skate weight over
the wire loop and attach the string to the appropriate groove on the antieskating stub:
- For the OM10, set the string in the middle groove (Groove 2, shown in example above)
- For the 2M Red, set the string in the rearmost groove (Groove 3)
Important note: If you should change to a diflferent cartridge in the future, refer to more
detailed instructions in the owner's manual or on our website.
Page 12
STEP 8 - DUST COVER: Attach the dust cover by inserting it into the two hinges.
mm cam
Bluetooth
To pair your device:
1. Press the Bluetooth button to enter Bluetooth mode.
2. Enter Bluetooth pairing mode on your device per your device’s instructions.
3. You device should soon recognize THE+RECORD PLAYER. When
recognized, select to connect.
4. Use your device to play an audio signal. Be aware that your device’s volume
control may still operate in addition to the volume control on THE+RECORD
PLAYER, so if you do not have adequate volume make sure your device is
turned up to a reasonable level.
IfTHE+RECORD PLAYER does not show up on the Bluetooth screen ofyour device it
may be already paired to another device within range. It must be first disconnected from
that device before it can be paired with a new device. If you are certain this is not the case,
exit Bluetooth mode and reselect it to restart the scan process.
Recording and playing to, or from a PC
You may use THE+RECORD PLAYER to record your music to a PC or Mac, or play back
music stored on your hard drive. Connect a USE-Mini B to USB-A cable from the PC jack
on THE+RECORD PLAYER to a USB jack on your PC or Mac. It does not require any
special drivers or software, but will emulate an external soundcard so that it may be used
with any software you choose.
On your PC or Mac, enter the SOUND menu from within your Control Panel or System
Preferences. Select “USB CODEC" as the INPUT device for recording, and the OUTPUT
device for playback. You may now use built in apps such as Windows Media Player or
Quicktime to record or playback from whatever source, except PC, you have selected on
THE+RECORD PLAYER.
There is a variety of software and freeware available such as Audacity (www.audacityteam.
org), which provide features such as pop suppression and automatic track splitting.
Page 13
Vinyl Care
Unlike digital and solid state sources of music, turntables and vinyl LP’s require a gentle
touch to maximize performance and longevity. Following these guidelines will result in
years ofnoiseefree, reliable performance.
. Do not handle records by the grooved areas. Grasp them by the edges, or by
balancing the label on your thumb and steadying it with your forefinger at the
edge ofthe record. Fingerprint oils attract dust which increases wear and adds
noise.
. Invest in a good record cleaning brush and use it prior to each play.
. Invest in a quality residue-free record cleaning system. Use it after every few plays
or as needed.
- Always place your records back in their protective sleeves immediately after each
use. Never leave them laying around unprotected.
. Always store your records vertically, and away from heat and sunlight.
. Whenever possible, use the arm lift (a.k.a. cueing lever) to gently raise and lower
the stylus to the record surface.
- Clean the stylus regularly using a soft brush, or by blowing on it. Always brush
from back to front. NEVER brush from side to side or front to back or the stylus
will be damaged.
. Never play a record with a bent, misaligned, or damaged stylus or the record will
be permanently damaged.
. Always use the tracking force recommended by the stylus manufacturer. Setting
the force too light is as damaging to your valuable vinyl LP’s as setting it too
heavy.
Page 14
30-Day Satisfaction Guarantee for Orders on Plusaudio.com
We are so convinced that you will love your new +AUDIO product that if you are
dissatisfied in any way, you may return your unit (purchased through wwwplusaudio.
com) within 307days from the time your order ships for a full refund, minus the cost of
any damaged, missing or abused components.
Products purchased through an authorized reseller are governed by that reseller's policy
To initiate a return for a unit purchased online, please email us at support@plusaudio.
com (U.S./ Canada units) or infu@plusaudio.com (international units) with the following
information:
1. Your name, address, purchase date, phone number, and where the unit was
purchased.
24 Your purchase order number and product serial number (ifapplicable)
3. Your reason for returning the item: For example, repair or refund.
4. You will be issued a Return Authorization and a pre-printed shipping label, which
must be used to assure accurate transaction tracking.
5. You are responsible for items missing any parts or accessories. Damage due to
accident or abuse, or products not returned in their complete original packaging
will be subject to restocking and/or replacement fees. Returned items are the
customer’s responsibility until they reach the return address. A refund will be
issued once we receive the returned items (normally within 3 business days),
Refunds do not include any shipping costs.
Product Cleaning
Use a soft dry or slightly damp cloth, or compressed air.
Do not use harsh cleaner anywhere on the products Only clean the exterior of the
products Fine dust cover scratches can be treated with a mild abrasive compound such as
toothpaste or automotive headlight cleaner and microfiber cloth.
Page 15
Specifications
Description: Integrated phonograph with
Bluetooth, USB, Toslink, and Auxiliary
inputs
Music Power: 100W total (2 x 35W to
woofers + 2 x 15W to tweeters)
Acoustic Frequency range: SSHz — ZOkHz
+/7 3dB (under laboratory conditions)
Turntable:
Motor: 24-pole AC Synchronous motor
driven by digitally synthesized 2-speed
electronic speed control
Platter: 12” Steel with felt mat
Speeds: 33.33/45 RPM
Wow and Flutter: <.2%
Drive system: Flat belt
Tonearm (Standard Edition): One piece
damped aluminum
Tonearm (Special Carbon Edition): One
piece Carbon Fiber
Phono Cartridge:
Ortofon OM10 (Standard Edition); or
Ortofon 2m Red (Carbon Edition)
Optical Input: Toslink SPDIF 44,1kl-lz,
PCM
PC USB Input/Output: 44.1kHz/48kHz
167bit. Mac and PC compatible, no driver
required
Headphone Output: 150mW @ 16 Ohms.
Compatible with 16710k Ohm headphones.
Frequency Response: 20H2720kHz
Line Output: 1000mV, variable with
volume control
Power Consumption: 1007240VAC / 110W
max. <0.5W Standby current
Weight; 12.7 kg / 28 lbs
Shipping Weight: 15 kg / 33 lbs
Dimensions:
Height: 215mm / 8.5”
Width: 446mm/ 17.6” W
Depth: 356mm/ 14” D
Page 16
Contact
+AUD|O
Division of |MS&M Technology Ltd
4th Floor - Sutherland House
70778 West Hendon Broadway
London NW9 7BT , United Kingdom
T: +44 2082029519
info@plusaudio.com
Disclaimer
+AUD|O USA
(US/Canada)
PO BOX 764
North Andover. MA 01845
T;+1877.331.5380
support©p|usaudiacom
+AUDIO IS a registered trademark of |MS&M TECHNOLOGY Ltd,
PROJECT IS a registered trademark of of AUDIO TUNING Vertnebs GesmbHA
ORTOFON is a registered trademark of ORTOFON S/A.
Page 17
WARNING
CAUTION
Danger of explosion if battery is incorrect,
ly replaced. Replace only with the same or
equivalent type,
WARNING
Do not ingest the battery. Chemical Burn
Hazard.
The remote control supplied with this
product contains a coin/button cell battery,
If the coin/button cell battery is swallowed,
it can cause severe internal burns in just 2
hours and can lead to death.
Keep new and used batteries away from
children
If the battery compartment does not close
securely, stop using the product and keep it
away from children,
If you think batteries might have been
swallowed or placed inside any part of the
body, seek immediate medical attention
If the MAINS plug or an appliance cou-
pler is used as the disconnect device, the
disconnect device shall remain readily
operable
Use this apparatus in moderate climates.
Attention should be drawn to the environ-
mental aspects of battery disposal.
Page 18
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Profile CMM Type : Linotronic Profile Version : 2.1.0 Profile Class : Display Device Profile Color Space Data : RGB Profile Connection Space : XYZ Profile Date Time : 1998:02:09 06:49:00 Profile File Signature : acsp Primary Platform : Microsoft Corporation CMM Flags : Not Embedded, Independent Device Manufacturer : Hewlett-Packard Device Model : sRGB Device Attributes : Reflective, Glossy, Positive, Color Rendering Intent : Perceptual Connection Space Illuminant : 0.9642 1 0.82491 Profile Creator : Hewlett-Packard Profile ID : 0 Profile Copyright : Copyright (c) 1998 Hewlett-Packard Company Profile Description : sRGB IEC61966-2.1 Media White Point : 0.95045 1 1.08905 Media Black Point : 0 0 0 Red Matrix Column : 0.43607 0.22249 0.01392 Green Matrix Column : 0.38515 0.71687 0.09708 Blue Matrix Column : 0.14307 0.06061 0.7141 Device Mfg Desc : IEC http://www.iec.ch Device Model Desc : IEC 61966-2.1 Default RGB colour space - sRGB Viewing Cond Desc : Reference Viewing Condition in IEC61966-2.1 Viewing Cond Illuminant : 19.6445 20.3718 16.8089 Viewing Cond Surround : 3.92889 4.07439 3.36179 Viewing Cond Illuminant Type : D50 Luminance : 76.03647 80 87.12462 Measurement Observer : CIE 1931 Measurement Backing : 0 0 0 Measurement Geometry : Unknown Measurement Flare : 0.999% Measurement Illuminant : D65 Technology : Cathode Ray Tube Display Red Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Green Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Blue Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Page Count : 20 Create Date : 2018:07:23 18:21:32+08:00 Modify Date : 2018:07:23 18:21:32+08:00 Producer : Corel PDF Engine Version 15.0.0.486 Author : Administrator Creator : CorelDRAW X5 Title : 7-23-12EXIF Metadata provided by EXIF.tools