Andrew Base Station Subsystems Group AA190045 RRH 2x45W 1900MHz AA190045 RF151032 User Manual

Andrew Corporation, Base Station Subsystems Group RRH 2x45W 1900MHz AA190045 RF151032

Contents

Installation Manual

Mounting Kits For Wide Panel Antennas BSAMNT Series: Mounting systems for installations (60-115mm pipe diameter) for heavy duty applicationscylindrical pipe Installation InstructionsAndrew Institute offers installation training. Bulletin 639825-1 • Revision B • March 2013 Page 1 of 2WSHR,LK,SPLT,M12,STL,GALVPre-assembly of Downtilt BracketsTop / Middle Mount Installations4 (fully collapsed position)14EAPart Lists• Bracket edges parallel to each other.10M10 boltM12 bolt14BOLT,CARRIAGE,M12 X 200,STL,GALV 4M10 boltbe configured in pre-assemblyposition (fully collapsed).99 10812CRITICAL: For initial installation to pipe, downtilt brackets must 1318211EAITEM NO. DESCRIPTION QTY U/M1 PIPECLAMP BRACKET, NO FLANGE 2 EA2 PIPECLAMP BRACKET, SHORT FLANGES 2 EA3 NOTCHED BRACKET 1 EA4BRACKET 1 EA5 SCR,HCS,HEX,M8X25,STL,GALV 4 EA6 WSHR,LK,SPLT,M8,STL,GALV 4 EA7 TWO HOLE PLATE, 8mm X 1.25 PITCH 2 EA8 NUT,HEX,M10,STL,GALV 12 EA9 WSHR,LK,SPLT,M10,STL,GALV 6 EA10 SCR,HCS,HEX,M10X40,STL,GALV 6 EA11 NUT,HEX,M12,STL,GALV 8 EA12 WSHR,FLT,M12,13X28X2.5,STL,GALV 4 EA13MAXIMUM TORQUEM8 15N.m (11ft.lbs)M10 37N.m (27ft.lbs)M12 58N.m (43ft.lbs)ATTENTION: Insert M12 bolts and M12 flat washers into bracket with tabsprior to attaching bracket to antenna.6473two hole plate5M8 bolt
15N.m (11ft.lbs)37N.m (27ft.lbs)M12Bottom Mount InstallationM10adjust antenna angleuse inclinometer to Adjusting Antenna Tilt(loosen only)M10 pivot bolt 58N.m (43ft.lbs)(loosen only)M10 pivot bolt M10 bolt(loosen only)center locationM8 pivot boltM12 bolt(remove to adjust tilt)perimeter locationDETAIL AM10 pivot bolt (loosen only)1211M8 adjuster bolt 131910 8142MAXIMUM TORQUEM8MAXIMUM TORQUEM10 37N.m (27ft.lbs)M12 58N.m (43ft.lbs)(Continued from page 1)BSAMNT Mounting Kit CommScope • ATTENTION: Insert M12 bolts and M12 flat washers into bracket with tabsprior to attaching bracket to antenna.M10 pivot bolt Bulletin 639825-1 • Revision B • March 2013 Page 2 of 2(loosen only)International: +1-779-435-6500, Option 1ACustomer Support Center• Retighten all bolts.• Reinstall adjuster bolts.any specifications or warranties relating to Andrew products or services. (use inclinometer)• Adjust antenna angle.• Remove adjuster bolts. not remove)Loosen pivot bolts . (doNorth America: +1-800-255-1479, Option 1Email: BSASupport@CommScope.comVisit our Web site at www.commscope.com or contact your local sales representative for more information.© 2012 CommScope, Inc. All rights reserved.Andrew is a trademark of CommScope. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement applicable safety precautions as shown on this page.when the field installation is performed. Follow all It is recommended that transmit power be turned off results of improper or unsafe installation practices.ladder.is in the area. Do not use metal day or when lightning or thunder Do not install on a wet or windy CommScope disclaims any liability or responsibility for the electrocute you.Assume any wire or line can and guy wires look the same. Power lines, telephone lines, rubber gloves.including a long-sleeved shirt and heels. Wear protective clothingWear shoes with rubber soles and Do not install near power lines. maintenance, and condition of equipment. SAFETY NOTICEThe installation, maintenance, or removal of an antennarequires qualified, experienced personnel. CommScopeinstallation instructions are written for such installation personnel. Antenna systems should be inspected once a year by qualified personnel to verify proper installation, www.commscope.com/andrewCommScope
RF Safety Warning: Although the final configurations are determined at time of licensing, it is important that the antenna selection and installation do not exceed equipment authorization and adequate separation distance is maintained. One of investigated configurations is that RRH 2x45 MHz has an output EIRP of 5.2kW and a minimum RF safety separation distance of 6.4 meters with max gain 17.5 dBi.

Navigation menu