Ansen Electronics Co 0790TXA PIR Sensor User Manual 0784 5 eng im

Download:
Mirror Download [FCC.gov]
Document ID	497463
Application ID	jATAEeivtlN7HLqC921qZw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.84kB (97957 bits)
Date Submitted	2004-12-16 00:00:00
Date Available	2004-12-16 00:00:00
Creation Date	2004-12-08 18:34:16
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2004-12-08 18:29:23
Document Title	0784-5 eng im
Document Creator	Adobe PageMaker 7.0
Document Author:	amy

Driveway Patrol
Instructions
Congratulations on purchasing the Driveway Patrol! Your set comes with a volume controlled Chime Unit
and a Passive Infra-Red (PIR) Sensor. Both are battery operated. The Driveway Patrol system is simple to
install and requires no wiring.
Installing the Batteries:
1. The chime requires three C-size batteries (not included). To install the chime unit’s batteries, slide off
compartment cover in direction of arrow and then install the receiver’s batteries. Be sure to observe
correct polarity (+ and -) as marked inside the battery compartment.
2. The PIR sensor requires a 9V battery. To install the PIR sensor’s battery, unscrew the back cover of
the sensor and insert the battery. Be sure to observe correct polarity (+ and -) as marked on the battery
compartment.
Operation:
1. Your Driveway Patrol Receiver Chime Unit has 3 settings (Hi or Lo Volume and Off). To switch the unit
ON, select Hi or Lo Volume Settings.
2. Hang the PIR (Passive Infra Red) Sensor Unit at the entrance of your driveway (such as on a mailbox,
on a tree or on a ground stake). You may also place the PIR Sensor on your garage, near the front
entrance or rear door. Any movement nearby will transmit a signal to the Receiver Chime Unit triggering
it to signal the chime.
3. Please ensure to place the PIR Sensor at least three feet high above the ground.
4. Receiver must be used indoors.
Important Note:
A) Whenever installing the PIR sensor the first time, the red LED on the PIR sensor will be on for about 60
seconds and the chime unit will sound for about 60 seconds in order to stabilize the units first.
B) In some applications the motion detector may be too sensitive, resulting in false alerts. To remedy this
situation, put masking tape or labels on each side of the sensor window. Start on the sides and add an
equal length of masking tape or labels to each side. Test the detector and add more covering if needed.
Keep the band as narrow as 1/8” wide or wider depending on individual situation. Some trial and error
may be required to find the optimal width.
Specifications:
Transmission Range; 400 feet (open area)
Transmission frequency; 434MHz
PIR sensor range: 40˚ X 30 feet
Receiver: 3 X 1.5V “C-size” battery, not included
Transmitter: 1 X 9V battery, not included
FCC Part 15 compliance
Battery Caution:
1. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
2. Non-rechargeable batteries are not to be recharged.
3. Never mix old and new batteries.
4. Make sure batteries are inserted with correct polarity.
5. Exhausted or dead batteries are to be removed from the unit.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may case harmful interference to radio communications. However, there is no
gurantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/ TV technician for help.
Modifications not authorized by the manufacturer may void users authority to operate this
device.
ANSEN ELECTRONICS CO.
0784-5

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Modify, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res
Page Count                      : 2
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:0792da8e-4904-11d9-97c5-000d93b00e9a
Producer                        : Acrobat Distiller 6.0 (Windows)
Keywords                        : 
Create Date                     : 2004:12:08 18:34:16+08:00
Creator Tool                    : Adobe PageMaker 7.0
Modify Date                     : 2004:12:08 18:29:23+08:00
Metadata Date                   : 2004:12:08 18:29:23+08:00
Document ID                     : uuid:0abb2e1d-c971-42e6-8207-41dc7cfae9f8
Format                          : application/pdf
Description                     : 0784-5 eng im
Title                           : 0784-5 eng im
Creator                         : amy
Author                          : amy
Subject                         : 0784-5 eng im

EXIF Metadata provided by EXIF.tools