Arcade Shell Game Manual REV A 5 4 2011 User
2013-11-25
User Manual: Arcade Shell Game Manual
Open the PDF directly: View PDF 
.
Page Count: 18
| Download | |
| Open PDF In Browser | View PDF |
OWNERS AND SERVICE MANUAL INNOVATIVE CONCEPTS IN ENTERTAINMENT INC. 10123 MAIN STREET, CLARENCE, NY 14031 SERVICE: 1-716-759-0360 FAX: 1-716-759-0884 E-MAIL: service@icegame.com WEBSITE: www.icegame.com 2 Table of Contents Setup Programming Cabinet Access Monitor: Controls Power Removal I/O Board replacement Assemblies Spares Decal Layout Warranty 3 Setup Place the marquee on top of the cabinet as shown below. Attach using the provided hardware found in the cash box. A 3/16 Allen wrench has been included to tighten the hard ware. Remove the center back cover to access the two wire harnesses that will need to be attached to the marquee. The AC harness is located to the left, upper hole. The display harness is located in the middle and goes up the left side access hole. See below for pictures. The game is ready for location use. Please proceed to programming to configure your game for your location. 4 SEE PROGRAM INSERT FOR PROGRAMMING INFORMATION. 5 Lower Door Access Located at the bottom of the cabinet are two access doors. Standing from the front of the cabinet, the right door is used to gain access to the front of the computer along with the USB I.O board. The left door is used to gain access to the back of the computer and the A/C power module. Use the “Prop bar” to keep the doors open while you work inside the cabinet. Control Panel Access To open the control panel, open the front coin door and located the two latches at the side of the cabinet. They are circled below. Now you can clip the control panel up. 6 Monitor: Controls & Power supply Access At the back of the monitor housing are two access panels. The center access panel will give you access to the monitor control board located at the left of the monitor. See below for the monitor’s remote board layout. The right access panel will give you access to the monitor’s power supply. This power supply is +24 volts DC at 10 amps or higher. Power Source Increase Decrease Down Menu 7 Monitor Power Supply Removal Refer to “Monitor: Controls & Power supply Access” to gain access to the power supply. Remove the left mounting bolt and slide the power supply right to remove. Slide the supply to the left and reattach left mounting bolt to install. REMOVE INSTALL Monitor Removal Remove only the screws shown below to remove front glass assembly. Once the front glass assembly has been removed, you can remove the mounting screws that hold the monitor to the cabinet. Disconnect both the power input and video cable before removing monitor. You only remove this cover to replace monitor. Remove only these screws shown to remove front assembly 8 I/O Removal The I/O board is held to the back of the lower part of the cabinet by four plastic standoffs shown to the left. To access this, open the lower right side door and prop with prop arm. See “Lower Door Access” for more information. Remove the four plastic standoffs. 9 10 11 12 13 14 15 SPARES GO HERE 16 17 WARRANTY POLICY I.C.E. Inc warrants all components in new machines to be free of defects in materials and workmanship for the period listed below: ■ 180 days on Main PCB’s, Computers & Motors ■ 1 year on all LCD monitor panels ■ 90 days on all other electronic and mechanical components ■ 30 days on all I.C.E. repairs and parts purchases I.C.E. Inc shall not be obligated to furnish a warranty request under the following conditions: ■ Equipment or parts have failed through normal wear and tear ■ Equipment has been subjected to unwarranted stress, abuse or neglect ■ Equipment has been damaged as a result of arbitrary repair/modification Products will only be covered under warranty by obtaining an I.C.E. authorized RMA #. To obtain an RMA # please provide I.C.E. tech support with the game serial # or original I.C.E. invoice # and a detailed description of the failure or fault symptoms. I.C.E. Inc will assume no liability whatsoever for costs associated with labor or travel time to replace defective parts. All defective warranty covered components will be replaced with new or factory refurbished components equal to OEM specifications. I.C.E. Inc will cover domestic UPS ground, or comparable shipping costs during the warranty period. International or expedited shipments are available for an additional charge. To obtain credit defective parts must be returned to I.C.E. Inc, at the customer’s expense, within 30 days. After 30 days a 15% re-stocking fee will apply to all returns. ICE distributors are independent, privately owned and operated. In their judgment, they may sell parts and/or accessories other than those manufactured by I.C.E. Inc. We cannot be responsible for the quality, suitability or safety of any non-I.C.E. part or modification (including labor) that is performed by such a distributor. Innovative Concepts in Entertainment 10123 Main St. Clarence, NY 14031 Phone #: (716) - 759 – 0360 Fax #: (716) – 759 – 0884 www.icegame.com 18
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2011:05:04 15:46:50-04:00 Create Date : 2011:05:04 15:46:50-04:00 Format : application/pdf Title : Shell Game REV A 5-4-2011.pub Creator : David M. Bartel Producer : Acrobat Distiller 9.4.2 (Windows) Document ID : uuid:e44525af-35a9-4967-b85c-f362e9d178ad Instance ID : uuid:d09103ce-448f-4340-b42a-fe3bce8be734 Page Count : 18 Author : David M. BartelEXIF Metadata provided by EXIF.tools