Ardi Technology S01C1GP Digital RF Tracker 105 User Manual Exhibit E User Manual

Ardi Technology Corp. Digital RF Tracker 105 Exhibit E User Manual

User manual

Front & Rear ViewSpecificationsPackage ContentsFront BackSearch button 1Signal indicationDistance indicationShort Distance Power off BuzzerBattery coverHanging hole for strapClip Holding Way*** Do not cover the top side of Master. CorrectHoldingWrong HoldingDuring Search CorrectHoldingWrong Holding *** Do not sway Master. Master is always in front the body when take a turn.Search Luggage Tracker User Manual 2.Switch the power button of the Master and the Slave to “ON”, it will enter ”Search Mode”, please press search button to enter ”Standby mode”.3.Place the Slave to your kids, and take the Master with you or clip it on your belt. 3. Replace the battery cover.-MasterFront BackAlarmIf you hear a high beep alarm from the Master, it means that distance between the Master and Slave has been oversafe range (Set in short distance is 6~15m, and Long distance is 15~25m). The Master unit alarms and vibrates at this moment. .Suggested Setting placeLong Distance 6~15m(short distance)15~25m(long distance).Over Come with beep! Stop alarm (beep) if both devicescomes within safe range again. Search button 2for Slave 2 orMute for one Slave113321.For the first time use, please insert the batteries into the Master and the Slave sets according to the battery installation instruction as follows.1. Slide out the battery cover. 2. Insert the batteries. Make sure that the polarity +/- of the battery follow the markings on the bottom of the battery compartment. the Master. Contrarily, if the distance between the Master and the Slave is farther, less LED light are lit and the melody on the Master becomes slower . Use the LED and the melody indication as guides to find the Slave unit. One Slave only: To search the Slave unit, please press the "Search button 1" on the Master unit once. Two Slaves: To search the Slave 1, please press the "Search button 1" on the Master unit once. To search the Slave 2, please press the "Search button 2" on the Master unit once. The closer the distance between the Master and the Slave, the more LED lights are lit and the rapider the melody on If the distance between the Master and the Slave is out of detectable range and you turn to the wrong direction making the distance farther, the Master plays the melody and beeps every second to remind you to go back to the correct direction and detectable distance.While searching, the Slave makes low beep sounds every second. This can assist you in finding its position by tracking the sound when the Master and the Slave are already close. (Suggestion: Press and hold the Mute button on the Master to turn of the melody temporarily.Once you release the Mute button, the searching melody resumes again.)Press the "Search button" on the Master unit again to stop searching.While searching, always place the Master in front of your body and turn around slowly to find the connect direction by following signal indicator and distance melody. If you point at the correct direction,the Master shows more LED light and plays the melody more rapidly. .for Slave 1Slave 1 statusSlave 2 statusAlarm from Slave 1Alarm from Slave 2working range 0~500m/1640ft (line of sight) (the distance may be short depends on theterrain environment )Power & SignalindicationPower on/offONOFFBattery cover2Search RangeAlarm DistanceMaster/Slave Master (M05S)x1 Slave (S01)x1 Master (M05S)x1 Slave (S01)x1 Master (M05S)x1 Slave (S01)x2Battery Type LR44x2 CR2016x2 LR44x2 CR2016x2 LR44x2 CR2016x4Battery Life Time with Standby 50 days 60 days 50 days 60 days 30 days 60 daysBattery Life Time with Sleep over 90 days over 90 days over 90 days over 90 days over 90 days over 90 daysBeep Sound (at 10cm/3.9inch) 95 db 95 db 95 db 95 db 95 db 95 dbBulid-in None None Vibration Motor None Vibration Motor NoneDimension (L/W/H)52.8x39x13.2mm2x1.6x0.52inch80x50x2.8mm3.1x1.9x0.11inch52.8x39x13.2mm2x1.6x0.52inch80x50x2.8mm3.1x1.9x0.11inch52.8x39x13.2mm2x1.6x0.52inch80x50x2.8mm3.1x1.9x0.11inch105LM20~120m/328ftShort Distance : 6~15m/19~49ftLong Distance : 15~25m/49~82ft0~120m/328ftShort Distance : 6~15m/19~49ftLong Distance : 15~25m/49~82ft105L 105LM0~120m/328ftShort Distance : 6~15m/19~49ftLong Distance : 15~25m/49~82ftSearch, Alarm, 1 to 1 Search, Alarm with Vibration, 1 to 1 Search, Alarm with Vibration, 1 to 2Model NameFunctionPackage Contents 105L 105LM 105LM2Master(M05S) 1 set 1 set 1 setSlave(S01) 1 set 1 set 2 setsNameplate of Barrtery 1 set 1 set 2 setsBatteries LR44x2CR2016x2LR44x2CR2016x2LR44x2CR2016x4User manualStrapLuggage tag999Search Tip:
maySearch, detection, and alarm range depend on the terrain environment.kitthe theIf the beep sound is not loud enough, the batteries may be low. Change with new batteries for louder alarm sound.use the device trips,batteriesyourbatteries sources. It may cause danger or even explosion.Sleeping Low battery MuteFor 1 master and 1 slave: Press the Mute button to mute searching melody from the Master unit. Listen to beep sound from the Slave unit to assist short range searching.For 1 master and 2 slaves: Keep pressing the Serach button to mute searching melody from the Master unit.List beep sound from the Slave unit to assist short range searching.1. To avoid the pairing failure, please make sure the Slave 1, 2 and Master unit are under power off status.2. Press the "left" key on Master unit and turn on the Power at the same time. At the moment, two of the LEDs light. (As Graph 1)3. Keep pressing "left" key and press the "right" key. Then release "left" key and LEDs start flashing, and then release "right" key.4. At this moment the Master unit is under code-setting status and awaiting to be paired. (As Graph 2)5. Turn on the power of Slave unit and position it 5~10cm from Master unit to proceed the pairing.(As Graph 3)6. While Master unit and Slave unit are paired, both units enter Search mode.The pairing process of additional Slave unitGraph 1 Graph 2mlb.) When switching the Master unit power on, the Signal indication LED flashed as searching the Slave unit. If the Master and Slave units are out of working range, the Signal indication LED remains light while the Master unit could not find Slave unit.Switch the power button of the Master unit to OFF, when search function is not needed. Once you need thiskit to resume the standy mode, just turn the power button of the Master to ON.Important: a.) Please keep the Slave at ON status if you would turn the Master into Sleep mode.c.) Please trun off the Master and Slave unit if NOT in sue to save battery life.o5~10cmGraph 3Signal indication LEDs flashevery secondMelody is rapiderMelody is slower and diminuendoSignal indication LEDs flashevery secondMelody is slower and short beep every second!AlarmDiasble Alarm funstion: During at standby mode, the master and Sllave wuthin 2 meters, power off the Master unit.Enable Alarm function: Switch the Master power on.Switch the Power button to ONMore LEDs light upLEDs light decreasinglyTurn off the search melody of Master(long press the Mute button)SearchSignal indication LEDs flashSignal indication LEDs flashevery secondSignal indication LEDs flashevery secondHigh beeps while re-linkingHigh beep every secondLow batteryDisconnectUnder standy mode, press the”Search” buttonThis product operation temperature is between 32ʲ ~140ʲÛ&aÛ&. Storage temperature is between -4ʲ ~185ʲÛ&aÛ&91E-02B5-U50G00** The connection range depends on the terrain environment because of readio efficiency.

Navigation menu