Ardi Technology S07CXX Bike Guard / Motor Bike Guard Tag / Bike Alarm User Manual 708A3 20130912 ai

Download:
Mirror Download [FCC.gov]
Document ID	2306186
Application ID	FWYWP9Jw9cf2Mx16B0mtyg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	227.48kB (2843450 bits)
Date Submitted	2014-06-25 00:00:00
Date Available	2014-06-25 00:00:00
Creation Date	2013-12-23 09:02:07
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2014-03-21 11:45:36
Document Title	708A3 User Manual_20130912.ai
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

BIKE GUARD 708A3 USER MANUAL
2 GETTING STARTED
INTRODUCTION
Bicycles are stolen everywhere and every day no matter they are with or without locks. To protect your bicycle
from being stolen, our Digital RF wireless bicycle alarm system can be your best solution. Once the bike theft
happens, the Bike-Alarm will sound loud beeps to scare the thief away and the Beeper will also immediately
activate an emergency alarm to warn you to check the bicycle and take the necessary actions urgently.
Therefore, with Bike Guard 708A3 armed on the bicycle, whenever you want to take a short break in the cycling
journey, there is no need for you to worry about parking your bike nearby.
Product Description
Base Unit
1 Ring attachment
2 Speaker
3 Connecting status
4 Search button
Tag Unit
Sound output
Show the signal synchronous status between Base and Tag unit
Press to search for the Tag unit.
Power switch
Power ON/OFF
Battery cover
1 Screw Hole
2 Speaker
Sound output
Alert & Search
0~500m/1600ft
Vibration Sensor
Base Unit / Tag Unit
Base (M08AM)x1
Tag (S07C)x1
Battery Type
CR2032
AAAx2
Battery Life Time on Standby
45 days
70 days
Beep Audible Level (at 10 cm / 3.9 inches)
110db
127x40x12mm
4.99x1.57x0.47inch
How to apply/wear the Base and Tag units.
Package Contents
Strap
95 db
61.5x36x11.6mm
2.42x1.42x0.46inch
Dimension (L/W/H)
Batteries
2. Make sure that the Base and Tag units are in close proximity.
3. Turn ON the Power switch on the Base units. The base
units will establish a link and begin to blink synchronously .
4. Shock the Tag unit, and the base unit and Tag unit will beep.
5. Congratulations, now you are ready to put the Tag unit underneath the
bottle cage on a bike (in case the alarm is triggeved while installation).
Reminder Power Switch
ALERT
Bike Guard 708A3
Model Name
Function
Search Range
Alarm Triggered
Tag Unit
Tag Unit
a) Open from the fillister on the button of housing or curve
side by your nail, like open shell.
b) Insert batteries (included) following the polarity
markings in the battery compartment.
c) Close the battery compartment cover.
Specification
Base Unit
Base Unit
Open the battery cover by placing your thumb on the cover
(as shown) and pulling it backwards until it clicks open;
then lift off the cover.
Back
Front
Model Name
This section shows how to quickly setup and trigger an alert condition.
1. Place battery into the Base unit and the Tag unit.
Insert the battery into the battery compartment with the “+”
sign on the battery facing up. Then replace the battery
cover by sliding it up into compartment opening.
Back
Front
BIKE GUARD 708A3 USER MANUAL
708A3
Tag Unit
Base Unit
A sensor is built-in to detect the vibration, while someone is trying to move your bike, the Bike
Guard will alert you in 2 seconds. The Base&Tag unit will alarm for 10 seconds and repeat alarm
until vibration is stop.
Disarm Alarm:
Under standby mode, turn OFF the Master unit within 1 meters from your bicycle, the Tag unit will
sound "Di-du" to approval disarm. When you hear "Di-du", you have disarmed Bike Guard.
Beep Beep...
Beep Beep...
1 pc
1 pc
CR2032x1, AAAx2
Hook
User manual

Page 1
Page 2
BIKE GUARD 708A3 USER MANUAL
SEARCH
Additional Information
When a tagged item is misplaced, you can use the
Base unit to search for it, if it is within a 1600 ft / 500 m
(line of sight) radius. Try this first in an open area (e.g.
large room, or in your yard).
Press
1. Take the Base Unit and stand apart from the Tag
unit (about 15-20 ft). On the Base unit, press the
Search Button once. The Base unit will begin to
chirp and the Tag unit will begin to beep.
2. Before searching, you must first calibrate the Base
to the current terrain and environment. Hold the
Base unit in front of you at chest level, and scan
the area slowly in a circular direction, from right to
left for 360° (a) and again from left to right (b), one
360° turn in 3-4 seconds.
Note: You don’t have to scan a full 360°; you can
use a narrower search angle (e.g. 180°).
Note: If the “Direction Indicator” illuminates green
on the Base unit during this calibration process,
it does not yet indicate the Tag unit’s direction.
Calibrate
180-360
3. Next, begin the search by slowly scanning a third
time from right to left (c). The “Direction Indicator” on
the Base Unit will illuminate (green) when it
establishes the direction of the tagged item location.
Search
4. Move in the direction of the Tag Unit. As you
approach the Tag unit, the frequency of the chirping
and blinking (LED) on the Base Unit will increase.
5. If the Tag unit is hidden (e.g. in a pocket), you can
MUTE the Base unit by holding down the button on
the Base unit, allowing you to follow the Tag beep
audible to in-point Tag unit’s location.
BIKE GUARD 708A3 USER MANUAL
Tag unit
Scenarios
Base unit
Beeps for 10 seconds
Beeps for 10 seconds
Continuously send out beeps
Continuously send out beeps
No sound
Continuously send out beeps
Press the search button to locate
your bike
Continuously send out beeps
Green LED blinks
When the battery is low
Buzzer beeps once every
2 minutes
Buzzer beeps once every
2 minutes
When the bicycle movement still
continues,
When Tag unit is power-off, destroyed
or the bicycle is hijacked, …
Page 3
WARNIBGS AND INFORMATION
1. The Tag units are water-repellent, but not waterproof!
Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain
minerals that may corrode electronic circuits. If your device gets wet, remove the battery, and
allow the device to dry completely before replacing it.
2. If you want to use the device during air flight, please comply with the air safety regulations for
each respective country.
3. We reserve the right to change the hardware/software specifications and designs, as well as the
information in the manuals, at any time without prior notice.
4. Proper operating temperatures for this product are between 40˚F~103˚F
(5˚C~40˚C). Proper Storage Temperatures are between -4˚F~185˚F (-20˚C~85˚C) .
5. Under low battery charge conditions, both Base and Tag will alert with a beep every 2 minutes in this case, replace batteries immediately. Low battery conditions may result in unpredictable
product behavior, such as low alert volume and false readings. To save battery charge, turn off
both units when appropriate (e.g. evenings at home).
6. The Batteries provided in this product should be disposed of properly according to national or
regional recycling regulations - contact local authorities for more information.
Warning: Do not expose the batteries to fire or heat - this may result in danger from explosions.
OPERATION INSTURCTION
When the bicycle is shocked
accidentally,…
Out of range or Loss signal :
a.) Base unit beeps and signal LED blinks for 80 seconds out of range or loss signal; then Base unit
will enter sleep mode automatically.
b.) Base unit beeps once a minute (to remind user to switch power OFF for Base unit for power-saving.)
c.) To wake-up Master , press Search button to go to wake-up process.
Low battery:
When the Matser and Slave is under low battery condition, it will beep at a 2 minutes interval,
please change the battery.
Important: Under low battery condition, it may cause abnormal function of alarm or searching.
CERTIFICATIONS
Federal Communication Commission Interference Statement
This equipment has been tested and improved to comply with the limits of a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This FCC Certifications equipment generates, uses and can radiate radio frequency energy, if
installed and used not in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determinedly turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept an interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications are not expressly approved by the party responsible for compliance which
could void the user's authority to operate this equipment.
EU Declaration Conformity
This product is carrying the CE-Mark in accordance with the related European Directives.
Page 4
91E-02B8-U50G20

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Administrator
Create Date                     : 2013:12:23 09:02:07+08:00
Modify Date                     : 2014:03:21 11:45:36+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2014:03:21 11:45:36+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : 708A3 User Manual_20130912.ai
Creator                         : Administrator
Document ID                     : uuid:085b9706-0239-4a87-ab50-fb4aced1ee0f
Instance ID                     : uuid:2d51d1c9-0d3b-4ad8-bfaf-f4c205b6513c
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Page Count                      : 2

EXIF Metadata provided by EXIF.tools