Ardi Technology SB20 Keyring Locator/Kid Tracker/Remote Controller User Manual iReminder SB20 20130517 ai

Download:
Mirror Download [FCC.gov]
Document ID	2035795
Application ID	LcKH5Mk4EjqJfiH9npCwCA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.25kB (253139 bits)
Date Submitted	2013-08-07 00:00:00
Date Available	2013-08-07 00:00:00
Creation Date	2013-07-15 18:15:30
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2013-07-18 14:53:11
Document Title	iReminder SB20 user manual_20130517.ai
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

Multiple iReminder SB20 User Manual
Step 5 - Run ”HiProx Multi” application
Introduction
Introduction
An electronic leash that will sound an alarm when your iPhone leaves
your vicinity. You can also use your iPhone to find the lost iReminder
thanks to the duplex communication protocol. A handy app called
HiProx Multi, will show on Google Map the last time the iReminder and
phone were connected. As a remote shutter release for self-portraits or
to prevent blur by shaking camera. The app can control the alarm
threshold distance, set the iReminder to start beeping when a call is
incoming, and switch the proximity alarm on/off. HiProx Multi for use
with multiple iReminder units and includes all of the mentioned
features. Simple to use interface allows you to re-name each tag
attached to your valuables, such as Keys, Wallet, etc. A brilliant little
device that could save you a lot of trouble.
a. Open ”HiProx Multi” and tap the
button in the upper right
corner to discover all available devices.(Figure 3)
b. ”HiProx Multi” will pop up Bluetooth Pairing Request.(Figure 4)
c. Select ”Pair” from ”Bluetooth Paring Request” for each device. The
Green LED light will blink once every 5 seconds in the connecting
mode.
Specification
Signal Indication
Communication Standard
Bluetooth® 4.0 Low Energy Wireless Technology
Compatibility
iPhone 4S/5, iPad 4, New iPad, iPad Mini with iOS 6 or later
Search Range
164ft/50m(*Distance will vary depending on terrain and other factors.)
Alert Range
6~50ft/2~15m adjustable (Near: 16±10ft/5±3m, Far: 32±16ft/10±5m)
Battery Type
CR2032x1
Battery Life
6~12 months
Beep Sound
High Alert: 95±3db, Mid Alert: 90±3db (at 10cm/3.9inch)
Figure 3
Figure 4
Figure 5
Figure 7
1. Enter Help menu
2. Find new device
3. Find my tag
4. Setting button
5. Signal indicator
6. Remove tag button
7. Beep sound setting for tag
8. Change device name
9. Battery status
10. On/Off call alert function
11. On/Off link loss function
12. On/Off range alarm function
13. Set alarm range
14. Alarm sound setting
15. On/Off Map location function
16. Enter Map view menu
17. Enter Camera function
18. Enter airplane mode setting
Dimension/Weight
61.5x36x11.6mm (2.42x1.42x0.46inch) / 9.5g
Working Temperature
Temperature: 5℃~40℃, humidity : 20%~80%
18
10
11
12
Package components
13
16
17
Figure 6
Step 6 - Test the iReminder system
Productdescription
Description
43 Product
Front
a. From MainView available devices table, you can tap desired item to
select that device. Once device has been selected,
button will
appear in that row.(Figure 5)
b. Press
button, the iReminder unit will beep to do FindMe function.
c. Press ”FindMe” button on the iReminder unit , and your BLE device
will beep.
d. Press and release ”Find Me” button to stop the FindMe function.
e. To set different alarm sounds for each tag, press 'Alarm Button'
(Figure 6)and go to Alarm Sound Selection View to choose your alert
tone for that tag.
f. Set alarm ”threshold level” depends on the alarm distance you like.
Step:
Range Alarm Threshold
Move the threshold bar
depends on the distance alarm you need.(Figure 6)
g. Test your setup by placing the iPhone in a stationary location. Then
take the Reminder and walk away from the iPhone - when you reach
6-50 feet from the iPhone, the Reminder will begin to beep. If you
move back into the range, the alarm will cease. (Figure 8)
Back
LED
Battery Cover
Device FindMe
Button
Power Off
Power On
Key Chain Hock
Power Switch
14
15
A) iReminder Unit x 1
B) Key Chain Hock x 1
C) Battery(CR 2032) x 1
D) User Manual x 1
If any components are missing from the package, please return the
product to your dealer immediately.
Quicksetup
Setupguide
Guide
Quick
Step 1 - Download App ”HiProx Multi”
Download ”HiProx Multi” on App Store for free.
(Please search for HiProx Multi on App store, or search for BLE and
find the HiProx Multi application)
6-50 Feet
Step 2 - Enable Bluetooth on your iPhone/iPad
Go to
Setting
General
Enable Bluetooth
Step 3 - Place battery into iReminder Units
Figure 8
a. Open the battery cover by placing your thumb on the cover
(as shown) and pulling it backwards until it clicks open; then lift
off the cover.(Figure 1)
b. Insert the battery into the battery compartment with the the ”+”
sign on the battery facing up. Then replace the battery cover
by sliding it up into compartment opening.(Figure 2)
Figure 1
Figure 2
Step 4 - Turn on the iReminder Units
Once turn on the iRminder units, and it will enter automatically to
pairing mode. Green LED will blink per second to indicate device is
ready to pair.
Page 1
FindMe Function
a. To locate the missing item, tap green
button from available
device st. The missing device will continue beep for 5 seconds
from each request. Re-tap green
button again to continue
searching function.
b. Press and Release Device 'FindMe' button (hardware button under
the LED) will gernerate ”FindMe Request” from that Device. Your
iOS device (iPhone / iPad...) will issue Alert sound continuesly.
Press and Release Device FindMe button to stop this request.
c. Tap green
button from iOS Device will Mute 'FindMe Request
Alert Sound.
d. Holding the device button for over 3 seconds will force the device
to enter SLEEP mode and generate a linkLossAlert to the iOS
device; to wake up and re-connect to the iOS device, ress and
release device button.
7
Mode option and tap 'Reconnect' to connect all devices. If all
devices are in sleep mode, please press and release device
button to wakeup each device. In this case, you have to exit App
and Run again to reconnect all device (this may take up to 20
seconds for device in SLEEP mode).
c. Press and release device button, Device will wake up from sleep
mode and send connection request to iOS DEVICE. iOS DEVICE
Will automatically connect to this device with "Connected"
message.
d. To temporarily stop using one or more devices, enter sleep mode
for each device. Hold device button for over 3 seconds until you
hear the first beep or the status LED light blinks Red. If you are still
in connect mode, a link lost alert will register to iOS DEVICE and
iOS will issue Alert Sound with 'LinkLoss/sleep' message. Tap that
row to stop Alert Sound. You can wakeup that device by press and
release device button once. iOS Device will detect wakeup signal
and enable connection automatically.
e. Device LED will stop blinking when it is in sleep mode.
f. You can remove device permanently by tapping the red Remove
button(Figure 12) in the upper right corner of the SetView page. To
delete this device(Figure 13) ,Please GO TO your iOS Device
Settings menu, select General/Bluetooth . You should see the
name of the device you want to remove, tap it and choose "Forget
this device".
Map Locate
a. To set map Location function manually, go to SetView Menu page
and tap the
button to go to MapView.(Figure 9)
b. To manually select a Location mark, tap the
button and
choose [YES] ,you will see a red mark pin on the current blue
location mark.(Figure 10)
c. Auto set map location function: go to MapView Menu and tap the
button and remove the current mark pin , then enable the
Map Location function. When your iOS Device detects linkLossAlert ,
the iOS Device will automark the Location pin on MapView.(Figure 11)
Please notice map location is at the base of the iOS Device
GPS function if outdoors. If indoor, Please enable Wi-Fi to get
Location accurately.
Figure 9
Figure 10
Figure 11
Forget device
Figure 12
12
Notification of incoming calls
AirPlane Mode
Option A: After Airplane Mode has been turned 'ON'.
Press and release device button once for each device to disable alert
sound. Please go to Help/AirPlaneMode option: tap the
button by select [YES] to disconnect all Devices and exit App now
(please follow instructions from App)
To reconnect to all devices: tap the
button and choose
[RECONNECT] and exit App now (please follow instructions from
APP). If you can not connect all devices at once, please repeat
AirPlaneMode disconnect / reconnect steps to RECONNECT all
devices.
Option B: Enable sleep mode for all devices:
Press and release device button over 3 seconds for each device, you
should hear beep once to confirm sleep mode. Your iOS DEVICE will
register 'LinkLoss/Sleep detected' message and go to Help/AirPlane
Mode to disconnect all devices (please follow instruction from App)
and exit App now. You can go to setting and turn 'ON' the Airplane
Mode.
To reconnect the all devices: you have to wakeup each device by
press/release device button once. Tap the
button and
choose [RECONNECT] and exit App now (please follow instructions
from APP). If you can not connect all devices at once, please repeat
AirPlaneMode disconnect / reconnect steps to RECONNECT all
devices.
11
Figure 13
Figure 14
Troubleshooting
If you try to discover a device, but cannot find it, this usually
indicates that there is existing bond information. Locate and
remove(Figure 12) existing bond information from your iOS device
and from Bluetooth Setting to "Forget device". (Figure 14)
May be you need to shut down iOS device to clean holding
information completely.
Removing bond information from iOS
Bond information can be removed from the Settings menu, by going
to General and then Bluetooth. There you should see the name of
the device you want to remove, tap it, and choose "Forget this
device". (Figure 14)
Step :
HiProx_CXXXXX
Please go to SetView Menu to enable the call alert function.
Step:
Call Alert
Enable
When you get a phone call, the iReminder will start beeping and
flashing to remind you.
10
Delete device
Remote control for Photo Capture
To use the 'Photo' remote control function, go to the SetView page
and tap the Capture button to go to Capture View. The Smart Tag
remote key can control your smartphone camera function for photo
capture with one second per 'capture count number' or one minute
per 'capture time'.
For the Photo Capture function: You can use '+' or '-' to increase or
decrease the 'Capture count number' up to 100 images. Press the
smart tag remote button to start photo image capture one image per
second for the specified capture count period (you only press the
remote button once and you can pan your camera around your
target area).
Remove device
Removing bond information from device
To remove device permanently:
a.) Disconnection device first and go to SetView page to ”Remove”
(Figure 12) and ”Delete” (Figure 13) Device. Follow “Removing
bond information from the iOS” setps to completely remove
device from the iOS.
Step :
YES
OK
b.) Remove battery from device and re-install to re-start pairing
process.
What can cause a false Out-of-Range alarm?
a.) Low battery power.
b.) The human body is also a source of interference; when carrying
both iPhone & iReminder, carry them on the same side of your
body.
c.) Interference/block by metal objects or high power signals used
by 2.4 GHz band devices (i.e. Wi-Fi networks or Microwave
ovens…).
Please change batteries if audible alarm becomes weak.
13
Warning
Do not disassemble, repair, modify or replace the iReminder Unit or any of its components.
Please comply with the national and international flight safety regulations when using device
during your flight trip.
When storing rechargeable batteries for collection, keep in a vented, non-metal container.
Operating for this product is between 40˚F~103˚F (5˚C~40˚C). Storage for this product is
between -4F˚~185˚F(-20˚C~85˚C).
Do NOT dispose of the battery in public trash; it is unlawful under state and federal
environmental laws and regulations.
Please dispose of the battery at local battery recycling center.
Stop using device
a. To DISCONNECT all active device, please go to Help/ AirPlane
Mode option and tap 'YES' to disconnect all devices. Device
will enter standby mode after 30 seconds. Green LED will blink
every 10 seconds to indicate standby mode.
b. To RECONNECT all active device: please go to Help/AirPlane
Page 2
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to operate this equipment. (Example
- use only shielded interface cables when connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2013:07:18 14:53:11+08:00
Create Date                     : 2013:07:15 18:15:30+08:00
Metadata Date                   : 2013:07:18 14:53:11+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : iReminder SB20 user manual_20130517.ai
Creator                         : Administrator
Document ID                     : uuid:2af36b30-9384-4064-88bf-1622d8b10f2f
Instance ID                     : uuid:9ff52b0b-908a-4269-a0d0-2fd8157e36b7
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Page Count                      : 3
Author                          : Administrator

EXIF Metadata provided by EXIF.tools