Argox Information Co SDMN 802.11B/G/N SDIO Module with Antenna Connectors User Manual ARGOX SDM 802 11 BGN

Download:
Mirror Download [FCC.gov]
Document ID	1922102
Application ID	FHyYrHwx1kRpYtHa1d0mFA==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.57kB (407187 bits)
Date Submitted	2013-03-21 00:00:00
Date Available	2013-03-21 00:00:00
Creation Date	2013-03-21 11:30:40
Producing Software	Acrobat Distiller 9.5.3 (Windows)
Document Lastmod	2013-03-21 11:30:40
Document Title	Microsoft Word - ARGOX-SDM-802 11 BGN.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	geniechang

802.11B/G/N SDIO Module with Antenna Connectors
ARGOX­SDM­802.11 BGN
WLAN Module
User Manual
ARGOX­SDM­802.11 BGN WLAN Module
Product Specification
Features:
‐ Core IC: Summit SSD‐40L
‐ IEEE 802.11b/g/n compliant
‐ designed for mobile devices
‐ supports WPA/WPA2/WEP 64‐bit & 128‐bit
encryption
‐ w/o Antenna
‐ Dimension: 19.5 x 18.4 x 3.5 mm
‐ SDIO interface
Model#: ARGOX­SDM­802.11 BGN WLAN
Module
IEEE802.11b/g/n compliant
Contents
Pin Definition
Specification
Block Diagram
Description
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐
5~8
Pin Definition
Pin No.
Pin Name
Pin No.
Pin Name
V3P3
11
BT_STATE
SD_DATA0
12
WLAN_ACTIVE
SD2_DATA1
13
BT_FREQ
SD2_DATA2
14
GND
SD2_DATA3
15
LED_IN
V3P3
16
LED_IN
GND
17
SD2_CMD
GND
18
SD2_CLK
NC
10
BT_PRIORITY
Specifications Table
Feature
Description
Physical Interface
0.62 mm pitch LGA (land grid array) (0.62 GSP)
Wi-Fi Interface
1-bit or 4-bit Secure Digital I/O
Antenna Interface
Single antenna port (when mounted on an MSD40L board)
Chip Set
Broadcom BCM4319
Input Voltage Requirements
3.3 VDC ± 10% (core)
I/O Signaling Voltage
1.8/3.3 VDC ± 10%
Current Consumption
802.11b (16 dBm output power)
(At maximum transmit power setting)
Transmit: 294 mA (970 mW)
Receive: 40 mA (132 mW)
Standby: TBD mA (TBD mW)
802.11g (13 dBm output power)
Transmit:275 mA (908 mW)
Receive: 40 mA (132 mW)
Standby: TBD mA (TBD mW)
802.11n (12 dBm output power) (20-MHz channel)
Transmit: 255 mA (842 mW)
Receive: 40 mA (132 mW)
TBD mA (TBD mW)
Operating Temperature
-20° to 70°C (-4° to 158°F) (SDIO)
Operating Humidity
10 to 90% (non-condensing)
Storage Temperature
-30° to 85°C (-22° to 185°F)
Storage Humidity
10 to 90% (non-condensing)
Maximum Electrostatic Discharge
± 2 kV
Length
10 mm (0.39”)
Note: Length, width, and thickness
measurements include the metal shielding.
Width
10 mm (0.39”)
Thickness
1.3 mm (0.05”)
Mounting
See “Mounting” section for more information
Wireless Media
Direct Sequence-Spread Spectrum (DSSS)
Orthogonal Frequency Divisional Multiplexing (OFDM)
Media Access Protocol
Carrier sense multiple access with collision avoidance
(CSMA/CA)
Network Architecture Types
Infrastructure and ad hoc
Network Standards
IEEE 802.11b, 802.11d, 802.11e, 802.11g, 802.11i, 802.11n
Data Rates Supported
802.11b (DSSS) 1, 2, 5.5, 11 Mbps
802.11g (OFDM) 6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11n (OFDM, MCS 0-7) 6.5, 7.2, 13.0, 14.4, 19.5, 21.7, 26.0,
28.9, 39.0, 43.3, 52.0, 57.8, 58.5, 65.0, 72.2 Mbps
Modulation
BPSK @ 1, 6, 6.5, 7.2 and 9 Mbps
QPSK @ 2, 12, 13, 14.4,18, 19.5 and 21.7 Mbps
CCK @ 5.5 and 11 Mbps
16-QAM @ 24, 26, 28.9, 36, 39 and 43.3 Mbps
64-QAM @ 48, 52, 54, 57.8, 58.5, 65, and 72.2 Mbps
802.11n Spatial Streams
1 (Single Input, Single Output)
2.4 GHz Frequency Bands
ETSI
2.4 GHz to 2.483 GHz
FCC
2.4 to 2.483 GHz
MIC (Japan) (formerly TELEC)
2.4 GHz to 2.495 GHz
KCC
2.4 GHz to 2.483 GHz
2.4 GHz Operating Channels
ETSI: 13 (3 non-overlapping)
FCC: 11 (3 non-overlapping)
MIC (Japan): 14 (4 non-overlapping)
KCC: 13 (3 non-overlapping)
Transmit Power Settings
802.11b
Note: Maximum transmit power varies
16 dBm (40 mW)
according to individual country regulations. All
802.11g
values nominal, +/-2 dBm
13 dBm (20 mW)
802.11n
12 dBm (16 mW)
Typical Receiver Sensitivity
Operating Systems Supported
Windows Mobile 6.5
Windows Mobile 6.1
Windows Mobile 6.0
Windows Mobile 5.0
Windows Embedded CE 6.0 R3
Windows Embedded CE 6.0 R2
Windows Embedded CE 6.0
Windows Embedded CE 5.0
Security
Standards
Wireless Equivalent Privacy (WEP)
Wi-Fi Protected Access (WPA)
IEEE 802.11i (WPA2)
Encryption
Wireless Equivalent Privacy (WEP, RC4 Algorithm)
Temporal Key Integrity Protocol (TKIP, RC4 Algorithm)
Advanced Encryption Standard (AES, Rijndael Algorithm)
Encryption Key Provisioning
Static (40-bit and 128-bit lengths)
Pre-Shared (PSK)
Dynamic
802.1X Extensible Authentication Protocol Types
EAP-FAST
EAP-TLS
EAP-TTLS
PEAP-GTC
PEAP-MSCHAPv2
PEAP-TLS
LEAP
Compliance
ETSI Regulatory Domain
Note: These agency approvals are pending.
EN 300 328
EN 301 489-1
EN 301 489-17
EN 301 893
EN 60950-1
EU 2002/95/EC (RoHS)
FCC Regulatory Domain
FCC 15.247 DTS – 802.11b/g/n (Wi-Fi) – 2.4 GHz & 5.8 GHz
FCC 15.407 UNII – 802.11a (Wi-Fi) – 2.4 GHz & 5.4 GHz
Industry Canada
RSS-210 – 802.11a/b/g/n/n (Wi-Fi) – 2.4 GHz, 5.8 GHz, 5.2
GHz, and 5.4 GHz
Certifications
Summit will be pursuing Wi-Fi Alliance and CCX certifications for
this radio in the near term.
Warranty
One-Year Warranty
All specifications are subject to change without notice
lectrical Specifications
Description
ARGOX‐SDM‐802.11 BGN WLAN module is designed with Summit SSD‐40L wireless LAN module IC
which compliant with IEEE802.11 b/g/n standard. It also supports WPA/WPA2/WEP 64‐bit & 128‐bit
encryption and external antenna must be applied to the module via J1 connector. It communicates with
host device by SDIO interface and external 3.3V dc power must be supplied to the module.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to
operate the equipment.
Labeling requirements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and must not be
co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must
be providing with antenna installation instructions and transmitter operating conditions for satisfying RF
exposure compliance.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may
be maintained between the antenna and users. The final end product must be labeled in a visible area with the
following: "Contains FCC ID: NBF-SDMN”
Information for the OEMs and Integrators
The following statement must be included with all versions of this document supplied to an
OEM or integrator, but should not be distributed to the end user.
1) This device is intended for OEM integrators only.
2) Please see the full Grant of Equipment document for other restrictions.
This radio transmitter FCC ID: NBF-SDMN has been approved by FCC to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this
list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Antenna List
No.
Manufacturer
Part No.
Antenna Type
Peak Gain
Ji-Haw
Ji-Haw
LYNwave
Wgt
Aristotle Enterprises
69-70002-001
69-70003-001
ALB120-052020-150052
AQ060WIPI01+A
69-70003-006
PIFA
PIFA
PIFA
PIFA
PIFA
3.48 dBi for 2.4 GHz
3.23 dBi for 2.4 GHz
2.70 dBi for 2.4 GHz
4.36 dBi for 2.4 GHz
3.40 dBi for 2.4 GHz
Note: The antenna connector is I-pex type.
Hosted Information
The “PA-6030” is a test-hosted board for Argox Information Co., Ltd. “ARGOX-SDM-802.11 BGN” RF module.
The hosted board manufacture and model name is Argox Information Co., Ltd. / PA-6030, PT-9130-1-1, PT-9230-1-1,
PT-9132-0-0, PT-9232-0-0
1. Hardware Setup
a.) The RF module need to soldered on the test-hosted board.
10
RF Module
The ARGOX-SDM-802.11 BGN has received Limited Module Approval (LMA) from FCC. This is because the
ARGOX-SDM-802.11 BGN does not have a built-in +3.3V regulator circuit. Argox Information Co., Ltd.
recommends that customers follow the +3.3V supply voltage requirements given in this data sheet.
If the power supply recommendations are followed, then customers will not need to go through formal certification of
the product for WiFi related RF behavior for FCC. It is the product manufacturers responsibility to make sure that the
power supply recommendations is followed, and that the RF behavior meets the certification requirements when the
module is installed in the final product.
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或
變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善
至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫
療用電波輻射性電機設備之干擾。
本模組於取得認證後將依規定於模組本體標示審驗合格標籤，並要求最終產品平台廠商
(OEM Integrator)於最終產品平台(End Product)上標示” 本產品內含射頻模組，
其 NCC 型式認證號碼為:
11
CCXXxxYYyyyZzW

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : geniechang
Create Date                     : 2013:03:21 11:30:40+08:00
Modify Date                     : 2013:03:21 11:30:40+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.5.3 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - ARGOX-SDM-802 11 BGN.doc
Creator                         : geniechang
Document ID                     : uuid:78aafbda-abd9-4264-a887-e51bdfe2d366
Instance ID                     : uuid:a5fe7b80-a52d-42f8-88fe-43d05e5f232d
Page Count                      : 11

EXIF Metadata provided by EXIF.tools