Aroot LK-P21B Mobile Printer User Manual

SEWOO TECH CO., LTD. Mobile Printer

User manual

All specifications are subject to change without noticeMOBILE PRINTERMODEL : LK-P21B
23Table of Contents 1. Product overview 3 2. Unpacking 4 3. Usage and Installation 5 3-1. Control panel usage5 3-2. Battery Installation6 3-3. Battery removal7 3-4. Battery charging8 3-5. Battery charger usage9 3-6. Usage of Cigar Jack for charging10 3-7. Belt clip usage12 3-8. Roll paper installation13 3-9. Leather case usage14 3-10. Self test15 3-11. MSR usage16 4. Peripherals connection 17 4-1. Bluetooth connectiontion17 4-2. Interface cable connection18 5. Printer specification 19 5-1. Specification191. Unpacking StandardOptionPrinter BatterySerial CableRoll paperBelt BuckleUSB Cable ShieldedChargerCD Quick ManualBattery Holder (Cradle) Leather case Shoulder stripCigar Jack
45 Button Name functionPower buttonThis button is used to turn the printer on and off.When the printer is off, press this button for approximately 2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off.Paper Feed ButtonPaper output can be done manually by pressing this button.Additionally, self-testing and Hexadecimal Dumping can be processed..1. Refer to “3-10” for self test information.2. Refer to the service manual regarding Hexadecimal Dumping.Battery Status Lamp1. If the Batt, LED are Lit, the battery is fully charged.2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level.3. If the battery is not charged at all, the printer turns off automatically.Error Lamp If the red light is turned on, it means there is no paper roll or the paper cover is open. 2. Product overview 3. Usage and Installation3-1 Control panel usagePaper feed buttonOpen ButtonPower switch SERIALUSB Belt clip hole BatteryDC Power
671. Align battery hook as shown in the picture2. Push the battery into the printer until it locks in place.NOTEAs the battery is not charged at the time of your purchase, charge the battery prior to using the printer(Battery charger or Cradle can be used to charge) Hook 1 2Put up the Belt clip hole turning 180 degree.After putting up the belt clip, remove the battery holding it up as shown above.180˚3-2 Battery Installation 3-3 Battery removal
893-5-1 The status of lamp in charginglampStatus charging charging complete Charging Lamp Red GreenNOTE1. Unless the exclusive charger is used provided by the manufacturer, the printer can be damaged, and the manufacturer is not liable for the consequential damage.2. Before removing the battery, make sure that power is turned off.3. Printer does not work in the status of being connected with charger only.4. The battery should be installed to operate printer.5. While charging, do not turn on the power.6. Do not operate the print while charging the battery.7. Do not connect the charger while the printer is operated.NOTEIn the case the battery is not fixed properly in the holder, the red lamp will be blinking, Then, extract and reinsert the battery.1. Be sure that the printer is turned off 2. After open the DC JACK cover, insert DC JACK into the printer.3. Plug the power code to electrical outlet.1. Insert the battery into the battery holder as shown above2. Connect the DC JACK to the power electrical outlet.3. Once the charging is completed, remove the battery from the holder.3-4 Battery charging 3-5 Battery charger usage
1011 1 2Connect the car cigar JACK charger into the printer or battery holder. As shown in the picture, tighten the screw with a screw driver.Insert the belt clip screw into the hole of Belt clip 3-6 Usage of Cigar Jack for charging 3-7 Belt Clip usagePrinterBattery holder
12131 2341 234Press the PUSH button to open paper coverOpen the leather caseClose the Velcro and stick the cover.Pull a short length of paper out of the printer and close the cover.Insert the paper in the right directionPlace the printer into the leather caseFasten to the belt by using the clip at the rear of the leather caseTear off the additional paper using tear bar.3-8 Roll Paper installation 3-9 Leather case usage
14151 23NOTEWhen the printer is installed initially or when you face a problem, you can run the self test and check the information about-Control Circuit, Mechanism, Print Quality, ROM VersionAfter checking with self-test and no issues are found, you can examine other devices and software. This function is working independent of devices and software. <The sample of self test printout>● Motor protection from being overheated The motor should be stopped and cooled about more than 30 seconds after continuous printing 1.5 meterTurn off the power pressing the power button for approximately 2 minutes.The printout is produced.While you are pressing the FEED button, press the power button3-10 Self Test1. To print ASCII pattern additionally, press the Feed button once more2. After printing ASCII pattern, the self test will be finished automatically.3. If the Feed button is not pressed to print ASCII pattern, self test will be finished automatically after 30 seconds.
16171. Printer can be connected to the PDA and PC which can do wireless communication.2. By using Bluetooth function supported in PC, printer can be connected.This printer can communicate with Peripherals device via Bluetooth and cables.Insert and swipe the card in the direction of the arrow as shown in the picture.3-11 MSR usage4-1 Bluetooth Connection4. Peripherals connection
1819SerialUSBPrinting Method Direct ThermalPrinting Speed 80mm/secResolution 203 DPI X 203 DPICharacter Font A (12X24), Font B (9X17)Character per line Font A : 32 columns , Font B : 42 columnsCharacter set ALPHA NUMERIC Charactor, Extension grapicBarcode EAN-8, EAN-13, Code39, ITF, UPC-A,Codabar, Code93, Code128Emulation ESC/POSDriver Window CE 4.2 & 5.0, Window Mobile 5.0Sensor Paper End Sensor , Cover open SensorPaper paper type Thermal Paperwidth 58mmthickness 65㎕External Diameter Max. Φ40mmInternal Diameter 12.5mm +/-0.5mmReliability TPH 50kmBattery Continuous printing operation: 1hr and 30minStandby: 24hrsPrinting length: 162mCommunications Serial(RS-232C), USB, Bluetooth Class2MSR (Optional) Card Standard ISO7811/2, JISTrack 1Track, 2Track, 3Track, JIS-IIMagnet Head Life 300,000 Passes(minimum)4-1 Bluetooth Connection1. Connect USB or Serial cable into the cable connector on the printer.2. Connect the interface cable into the USB or Serial port of the device (PDA, PC, etc.)NOTEUse the cable offered by the manufacturer (USB, Serial)5. Pritner Specification 5-1 Specification
2021Battery Charger input AC100~240V, 50/60 Hzoutput 8.4V , 800~1200mABattery Charger Battery type Li-onoutput 7.4V, 1130mAhCharging time 2 Time Size W X D X H(mm) 96 X 136 X 58W X D X H” 3.7 X 5.3 X 2.2Weight 0.4kgTemperature operation 5 ~ 40℃storage -10 ~ 50℃Humidity operation 35 ~ 95%
 3OHDVHUHIHUWRWKHSURJUDPPLQJPDQXDOLQFOXGHGLQ&'5GVVKPIWRVJGUQHVYCTG(%%+PHQTOCVKQPThis device complies with part 15 of the FCC Results. Operation is subject to the following two conditions: (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation.0QVGThis equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instuctions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. 9#40+0)%JCPIGU QT OQFKHKECVKQPU PQV GZRTGUUN[ CRRTQXGF D[ VJG OCPWHCEVWTGTEQWNFXQKFVJGWUGThUCWVJQTKV[VQQRGTCVGVJGGSWKROGPVǁ%GTVKHKECVKQP %#76+10#PVGPPCUJCNNDGOQWPVGFKPUWEJCOCPPGTVQOKPKOK\GVJGRQVGPVKCNHQTJWOCPEQPVCEVFWTKPIPQTOCNQRGTCVKQP6JGCPVGPPCUJQWNFPQVDGEQPVCEVGFFWTKPIQRGTCVKQPVQCXQKFVJGRQUUKDKNKV[QHGZEGGFKPIVJG(%%TCFKQHTGSWGPE[GZRQUWTGNKOKV
Rev. 1.0SEWOO TECH CO.,LTD.ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, KoreaTEL 82-31-459-8200 FAX 82-31-459-8880URL http://www.miniprinter.com

Navigation menu