Ascion RC-WM-101 Custom Memory Remote Control User Manual Controller 960624
Ascion, LLC Custom Memory Remote Control Controller 960624
Ascion >
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 812346 |
| Application ID | IfhHMT3fLZ9mu3YjFsjVWA== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 6.01kB (75105 bits) |
| Date Submitted | 2007-07-05 00:00:00 |
| Date Available | 2007-07-05 00:00:00 |
| Creation Date | 2007-06-25 09:11:00 |
| Producing Software | Acrobat PDFWriter 5.0Windows NT ª© |
| Document Lastmod | 2007-06-25 13:43:33 |
| Document Title | Controller User Manual 960624.doc |
| Document Creator | Controller User Manual 960624.doc - Microsoft Word |
| Document Author: | Administrator |
RC-WM-101 Controller Model: RC-WM-101 FCC ID. : VFKRC-WM-101 THIS DEVICE COMPLIES WITH PART 15 OF THE FCCRULES. OPERATIONS IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: ( 1 ) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND ( 2 ) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFEERENCE THAT MAY CAUSE UNDESRIED OPERATION Power supply: Use 4 X AAA 1.5V Battery (6V) Description: The hand control will have an RF transmission, with a range of 9 feet (3 meters). The RF transmission will have a “key code” to give each remote a unique transmission signal. It will have raised rubber buttons that will have the ability to be backlit when pressed. The hand control will have an ergonomic design and will use 4 AAA batteries. There will be approximately 21 buttons; the circuit board should have Functional Remote Description: Head Lift motor Button “+” • When pressed, it will initiate the Head lift motor to move the head of the bed up. • LED lights up when pressed. • Backlight initiates and it lights up all button. • When pressed during the “Flat” function it will interrupt the Flat cycle and stop the bed motion. Head Lift motor Button “-” • When pressed, it will initiate the Head lift motor to move the head of the bed down. • LED lights up when pressed. • Backlight initiates and it lights up all button. • When pressed during the “Flat” function it will interrupt the Flat cycle and stop the bed motion. Foot Lift Motor Button “+” • When pressed, it will initiate the Foot lift motor to move the foot of the bed up. • LED lights up when pressed. • Backlight initiates and it lights up all buttons. • When pressed during the “Flat” function it will interrupt the Flat cycle and stop the bed motion. Foot Lift Motor Button “-” • When pressed, it will initiate the Foot lift motor to move the foot of the bed up. • LED lights up when pressed. • Backlight initiates and it lights up all buttons. • When pressed during the “Flat” function it will interrupt the Flat cycle and stop the bed motion. Flat Button “FLAT” • When pressed, it will initiate the Head and Foot lift motors to return to the fully lowered position from any lifted position. • Must be held for 3 seconds to initiate. • LED lights up when pressed and blinks while the bed is lowered. • Backlight initiates and it lights up all buttons. • When pressed during the “Flat” function it will interrupt the Flat cycle and stop the bed motion. Custom Memory Recall Button “CUSTOM #1” • When pressed, it will recall the memory position #1 of the head and foot lift motor positions from the memory. • When held for 3 seconds it sets the custom position at the bed’s current position to memory position #1. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. • Upper Backlight LEDs and RF LED indicator h 3 times when memory is saved. • When pressed during the “Flat” function it will interrupt the Flat cycle and stop the bed motion Custom Memory Recall Button “CUSTOM #2” • When pressed, it will recall the memory position #2 of the head and foot lift motor positions from the memory. • When held for 3 seconds it sets the custom position at the bed’s current position to memory position #2. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. • Upper Backlight LEDs and RF LED Flash 3 times when memory is saved. • When pressed during the “Flat” function it will interrupt the Flat cycle and stop the bed motion. Custom Memory Recall Button “CUSTOM #3” • When pressed, it will recall the memory position #3 of the head and foot lift motor positions from the memory. • When held for 3 seconds it sets the custom position at the bed’s current position to memory position #3. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. • Upper Backlight LEDs and RF LED Flash 3 times when memory is saved. • When pressed during the “Flat” function it will interrupt the Flat cycle and stop the bed motion Custom Memory Recall Button “CUSTOM #4” • When pressed, it will recall the memory position #4 of the head and foot lift motor positions from the memory. • When held for 3 seconds it sets the custom position at the bed’s current position to memory position #4. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. • Upper Backlight LEDs and RF LED Flash 3 times when memory is saved. • When pressed during the “Flat” function it will interrupt the Flat cycle and stop the bed motion Wave Vibration Motor Stop Button “STOP” • When pressed, it will stop the Head and Foot vibration motors. • For all Wave types, the “Stop” button MUST be pressed before you are allowed to choose another massage type/intensity. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. Foot Vibration Motor Button “+” • When pressed, it will initiate the Foot vibration motor and when pressed again it will increase the intensity. • It should have a total of 10 intensities. • It will start at the 50% intensity level of a standard vibration. • MUST press vibration “STOP” before changing wave intensity/mode. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. Foot Vibration Motor Button “-” • When pressed, it will initiate the Foot vibration motor and when pressed again it will decrease the intensity. • It will start at the 50% intensity level of a standard vibration. • It should have a total of 10 intensities. • MUST press vibration “STOP” before changing wave intensity/mode. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. Head Vibration Motor Button “+” • When pressed, it will initiate the Head vibration motor and when pressed again it will increase the intensity. • It will start at the 50% intensity level of a standard vibration. • It should have a total of 10 intensities. • MUST press vibration “STOP” before changing wave intensity/mode. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. Head Vibration Motor Button “-“ • When pressed, it will initiate the Head vibration motor and when pressed again it will decrease the intensity. • It will start at the 50% intensity level of a standard vibration. • It should have a total of 10 intensities. • MUST press vibration “STOP”before changing wave intensity/mode. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. Wave Vibration Motor Button “Wave 1 ” • When pressed once, it will initiate the Head and Foot vibration motors to the “Wave #1” vibration mode. • It will start at the 50% intensity level. • Wave 1 represents the alternating vibration from head to foot in 1 second intervals. • Press and hold again for 3 seconds and it will shut off all vibration, • • • MUST press vibration “STOP” before changing wave intensity/mode. LED lights up when initiated. Backlight initiates and it lights up all buttons. Wave Vibration Motor Button “Wave 2 ” • When pressed once, it will initiate the Head and Foot vibration motors to the “Wave #2” vibration mode. • It will start at the 50% intensity level. • Wave 2 represents the alternating vibration from head to foot in 2 second intervals. • Press and hold again for 3 seconds and it will shut off all vibration, • MUST press vibration “STOP” before changing wave intensity/mode. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. Wave Vibration Motor Button “Wave 3 ” • When pressed once, it will initiate the Head and Foot vibration motors to the “Wave #3” vibration mode. • It will start at the 50% intensity level. • Wave 3 represents the alternating vibration from head to foot in 3 second intervals. • Press and hold again for 3 seconds and it will shut off all vibration, • MUST press vibration “STOP” before changing wave intensity/mode. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. Wave Vibration Motor Button “Wave 4 ” • When pressed once, it will initiate the Head and Foot vibration motors to the “Wave #4” vibration mode. • It will start at the 50% intensity level. • Wave 4 represents the alternating vibration from head to foot in 4 second intervals. • Press and hold again for 3 seconds and it will shut off all vibration, • MUST press vibration “STOP” before changing wave intensity/mode. • LED lights up when initiated. • Backlight initiates and it lights up all buttons. Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2007:06:25 09:11:00Z Modify Date : 2007:06:25 13:43:33+08:00 Page Count : 5 Has XFA : No Creation Date : 2007:06:25 09:11:00Z Author : Administrator Producer : Acrobat PDFWriter 5.0Windows NT ª© Mod Date : 2007:06:25 13:43:33+08:00 Metadata Date : 2007:06:25 13:43:33+08:00 Title : Controller User Manual 960624.doc Creator : AdministratorEXIF Metadata provided by EXIF.tools