Asis Technologies R300 Reader User Manual R300 Reader UserGuidex

Asis Technologies Pte Ltd Reader R300 Reader UserGuidex

Users Manual

1 R300 Series NFC Reader User Manual Document History Description Mar 2017 Revision 1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
2 Contents Document History ...................................................................................... 1 Federal Communication Commission Interference Statement .................. 1 1.1 R300 Series NFC Reader Overview ........................................ 2 1.2 Reader Wiring and Color Code ................................................ 3 1.3 DIP Switch Setting (See table 4,5 for detail) ........................... 3 1.4 Dimension ................................................................................ 4 1.5 Installation And Mounting Instruction ....................................... 5 1.6 Operation Guide ...................................................................... 6 1.7 Package List – R300 Reader ................................................... 9 1.8 Product Electrical Specification ............................................. 10 1.1 R300 Series NFC Reader Overview The R300 Series NFC Reader is a weather proof, high heat ABS NFC card reader. The R300 Series NFC reader can read a wide range of contactless smart card covering single size UID card to double size UID card. Card ID data can be output via industry standard Wiegand or Asis Proprietary RS485.
3 1.2 Reader Wiring and Color Code Terminal Point Label Description Recommended Cable Color Dev+ RS485+ Blue Dev- RS485- Grey +V +12VDC Red GND DC Ground Black D0 Wiegand Data 0 Green D1 Wiegand Data 1 White ERL Red LED Brown OKL Green LED Orange BUZ Buzzer Yellow Hold Purple Table 2 Wiring and Cable Color code 1.3 DIP Switch Setting (See table 4,5 for detail) BIT 1 2 3 4 5 6 7 8 Function (RS485) ADDRESS BIT MODE and Data Out BIT TEST BIT bit 0 bit 1 bit 2 bit 3 Off-Wiegand On- RS485 Off- 8 byte On -4 byte Off – CSN On - CAN Off – Run On - TestingFunction (Wiegand) Card format Setting Table 3 Dip Switch function explain
4 1.4 Dimension Reader Module DimensionFRONT SIDE76.00mm. 21.00mm.WebENTRA1 324 657 98* #0
5 1.5 Installation And Mounting Instruction Remove Bottom Screw Ply open the front cover using flat head screw driver remove the front of the unit. Remove the front of unit Mark out reader base (reader wire pigtail) and (wall mounting hole) drill hole on the wall for mounting reader. Half tighten wall mount screw. Terminate reader pigtail cable to cable from controller. Tighten wall mount screw
6 Reinsert reader front to base by set the bottom. Align reader pigtail cable accordingly. Push to front top to snap into the base. Tighten bottom screw 1.6 Operation Guide Keeping the card in parallel to the R300 reader a maximum read range can be obtained. The Reader will still be able to read Card when the card is presented at an angle but this will result in the reducing of read range. Card and PIN operation (Model 303) a) When the Green Led is blinking after presenting card, the means that PIN is request. Key in PIN and follows by “#” key b) Key in PIN + 1 for PIN DURESS (Example PIN is 1234, for duress activation, key pin 1235) Note that the maximum PIN is up to 6 digit. When the reader is powered-up, the LED and the Buzzer will respond.
7 c) Description Buzzer response (R300/R303) LED Response (R300/R303) a) Upon Power Up the Reader **N is setting on the DIP switch. The buzzer will beep (N+1) time accord to the DIP switch setting Reader’s Amber LEDs Blink (N+1) times b) Reader Ready Silent Red LED always ‘ON’ Green LED Short blink at every 3 secs interval Access Grant Buzzer Beep once Green LED Blink once Access Denied Buzzer Beep once Red LED Blink once Access Invalid Buzzer Beep once Red LED Blink once Door Open Too Long Buzzer Beeping Red LED Blinking Door Force Open Buzzer Beeping Red LED Blinking Free Access Silent Green LED ON Door Locked Silent Red LED ON Fire Activated Buzzer Beeping Red LED Blinking Box Tamper Buzzer beeping Red LED Blinking Pin Mode Buzzer beeping Green LED Blinking Pre-Alarm Buzzer beeping Red LED Blinking
8 BIT Reader Hex address 1 2 3 4 5 ~ 8 Function (RS485) BIT Address 1 80 Off Off Off Off Refer to above table 2 81 On Off Off Off 3 82 Off On Off Off 4 83 On On Off Off 5 84 Off Off On Off 6 85 On Off On Off 7 86 Off On On Off 8 87 On On On Off Table 4 RS485 Readers Address Dip Switch Setting Table 5 Wiegand bit format Dip Switch setting Note : Since the Contactless SmartCard CSN is 32 bit can be up to 10 digits decimal when converted. This is the solution to truncate the CSN and provide a result that once converted, it only give maximum of 8-digit decimal. The 37 bit odd and even priority bit is a result of getting the first and second half of total bit length. BIT 1 2 3 4 5~8 Function (Wiegand) Card format 26bit off off off off Refer to above table 32bit on off off off 32bit(8bit) off on off off 34bit on on off off 37bit off off on off 37(8digit) on off on off 40bit off on on off 40bit(8digit) on on on off 56bit off off off on 64bit on off off on 80bit off on off on 168bit(ASIS) on on on on
9 1.7 Package List – R300 Reader Item Description: Complete with snap on cover. 1 x Mounting cover security screw [M3], 1 x security screw driver, and this document. Radio Frequency Interference Devices generate RF noise that may interfere with the reception of the signal from the access card. This will result in the reduction of read range. Examples of devices are radios, televisions, and cellular phones. The read range is affected by the amount of interference (noise) in the area. The reader should mount more than 1.5m away from the any devices that emits RF that may interfere with the signal received from the access control cards.
10 1.8 Product Electrical Specification

Navigation menu