Asis Technologies R300 Reader User Manual R300 Reader UserGuidex

Download:
Mirror Download [FCC.gov]
Document ID	3338969
Application ID	vzm3B1iQGc1aDUfctbZySw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	45.01kB (562569 bits)
Date Submitted	2017-03-30 00:00:00
Date Available	2017-03-30 00:00:00
Creation Date	2017-03-14 16:29:48
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2017-03-14 16:29:48
Document Title	Microsoft Word - R300 Reader UserGuide.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	PCUser

R300 Series NFC Reader
User Manual
Document History
Description
Mar 2017 Revision 1
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this equipment. (Example - use
only shielded interface cables when connecting to computer or peripheral devices).
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Contents
Document History ...................................................................................... 1
Federal Communication Commission Interference Statement .................. 1
1.1
R300 Series NFC Reader Overview ........................................ 2
1.2 Reader Wiring and Color Code ................................................ 3
1.1
1.3
DIP Switch Setting (See table 4,5 for detail) ........................... 3
1.4
Dimension................................................................................ 4
1.5
Installation And Mounting Instruction ....................................... 5
1.6
Operation Guide ...................................................................... 6
1.7
Package List – R300 Reader................................................... 9
1.8
Product Electrical Specification ............................................. 10
R300 Series NFC Reader Overview
The R300 Series NFC Reader is a weather proof, high heat ABS NFC
card reader. The R300 Series NFC reader can read a wide range of
contactless smart card covering single size UID card to double size
UID card. Card ID data can be output via industry standard Wiegand
or Asis Proprietary RS485.
1.2 Reader Wiring and Color Code
Terminal Point
Label
Description
Recommended Cable
Color
Dev+
RS485+
Blue
Dev-
RS485-
Grey
+V
+12VDC
Red
GND
DC Ground
Black
D0
Wiegand Data 0 Green
D1
Wiegand Data 1 White
ERL
Red LED
Brown
OKL
Green LED
Orange
BUZ
Buzzer
Yellow
Hold
Purple
Table 2 Wiring and Cable Color code
1.3 DIP Switch Setting (See table 4,5 for detail)
BIT
Function
(RS485)
ADDRESS BIT
bit 0
Function
(Wiegand)
bit 1
MODE and Data Out BIT
bit 2
bit 3
Off-Wiegand
On- RS485
Off- 8 byte
On -4 byte
TEST BIT
Off – CSN
On - CAN
Off – Run
On - Testing
Card format Setting
Table 3 Dip Switch function explain
1.4
Dimension
Reader Module Dimension
21.00mm.
76.00mm.
WebENTRA
FRONT
SIDE
1.5
Installation And Mounting Instruction
Remove Bottom Screw
Ply open the front cover
using flat head screw driver
remove the front of the unit.
Remove the front of unit
Mark out reader base
(reader wire pigtail) and
(wall mounting hole) drill
hole on the wall for
mounting reader.
Half tighten wall mount
screw.
Terminate reader pigtail
cable to cable from
controller. Tighten wall
mount screw
Reinsert reader front to
base by set the bottom.
Align reader pigtail cable
accordingly. Push to front
top to snap into the base.
Tighten bottom screw
1.6
Operation Guide
Keeping the card in parallel to the R300 reader a maximum read range
can be obtained. The Reader will still be able to read Card when the
card is presented at an angle but this will result in the reducing of read
range.
Card and PIN operation (Model 303)
a) When the Green Led is blinking after presenting card, the means that
PIN is request. Key in PIN and follows by “#” key
b) Key in PIN + 1 for PIN DURESS (Example PIN is 1234, for duress
activation, key pin 1235)
Note that the maximum PIN is up to 6 digit.
When the reader is powered-up, the LED and the Buzzer will respond.
c)
Description
a) Upon Power
Up the Reader
**N is setting on
the DIP switch.
b) Reader Ready
Buzzer response
(R300/R303)
The buzzer will
beep (N+1) time
accord to the DIP
switch setting
Silent
LED Response
(R300/R303)
Reader’s Amber
LEDs Blink (N+1)
times
Red LED always
‘ON’ Green LED
Short blink at
every 3 secs
interval
Access Grant
Buzzer Beep once
Green LED Blink
once
Access
Denied
Buzzer Beep once
Red LED Blink once
Access Invalid
Buzzer Beep once
Red LED Blink once
Door Open
Too Long
Buzzer Beeping
Red LED Blinking
Door Force
Open
Buzzer Beeping
Red LED Blinking
Free Access
Silent
Green LED ON
Door Locked
Silent
Red LED ON
Fire Activated
Buzzer Beeping
Red LED Blinking
Box Tamper
Buzzer beeping
Red LED Blinking
Pin Mode
Buzzer beeping
Green LED Blinking
Pre-Alarm
Buzzer beeping
Red LED Blinking
BIT
Function
(RS485)
BIT
Address
Reader
Hex
address
5~8
80
Off
Off
Off
Off
81
On
Off
Off
Off
Refer to
above
table
82
Off
On
Off
Off
83
On
On
Off
Off
84
Off
Off
On
Off
85
On
Off
On
Off
86
Off
On
On
Off
87
On
On
On
Off
Table 4 RS485 Readers Address Dip Switch Setting
Function
(Wiegand)
Card format
BIT
26bit
32bit
32bit(8bit)
34bit
37bit
37(8digit)
40bit
40bit(8digit)
56bit
64bit
80bit
168bit(ASIS)
off
on
off
on
off
on
off
on
off
on
off
on
off
off
on
on
off
off
on
on
off
off
on
on
off
off
off
off
on
on
on
on
off
off
off
on
off
off
off
off
off
off
off
off
on
on
on
on
5~8
Refer to
above
table
Table 5 Wiegand bit format Dip Switch setting
Note : Since the Contactless SmartCard CSN is 32 bit can be up to 10 digits decimal when
converted. This is the solution to truncate the CSN and provide a result that once converted,
it only give maximum of 8-digit decimal. The 37 bit odd and even priority bit is a result of
getting the first and second half of total bit length.
1.7
Package List – R300 Reader
Item Description: Complete with snap on cover. 1 x Mounting cover
security screw [M3], 1 x security screw driver, and this document.
Radio Frequency Interference
Devices generate RF noise that may interfere with the reception of the
signal from the access card. This will result in the reduction of read range.
Examples of devices are radios, televisions, and cellular phones. The
read range is affected by the amount of interference (noise) in the area.
The reader should mount more than 1.5m away from the any devices that
emits RF that may interfere with the signal received from the access
control cards.
1.8
Product Electrical Specification
10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : PCUser
Create Date                     : 2017:03:14 16:29:48+08:00
Modify Date                     : 2017:03:14 16:29:48+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - R300 Reader UserGuide.docx
Creator                         : PCUser
Document ID                     : uuid:edda175c-ef51-46a8-9425-a78f66e9f114
Instance ID                     : uuid:eab7df2b-de66-42f4-94bf-d06bc6a1e5ca
Page Count                      : 10

EXIF Metadata provided by EXIF.tools