Askey Computer TCG220 Cable Modem User Manual rev

Download:
Mirror Download [FCC.gov]
Document ID	2813418
Application ID	WB5n8ydjSDIz5Ut88agSLw==
Document Description	User Manual rev.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.06kB (425802 bits)
Date Submitted	2015-11-16 00:00:00
Date Available	2015-11-16 00:00:00
Creation Date	2015-11-13 18:16:36
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2015-11-13 18:25:47
Document Title	Microsoft Word - QIG-PKE1320SW-D112_US-Tdp-RoHS__TCG220-Tdp_V1.0 20151113
Document Creator	PScript5.dll Version 5.2.2
Document Author:	nilin

Residential VoIP Cable Modem
Quick Start Guide
Chapter 1: Introduction
TCG220‐Tdp is a Full Band Capture Front End Cable Voice and Wireless Gateway which has an
802.11 b/g/n access point that gives you wireless connection to the Internet with 2 Giga
Ethernet ports which further expand the Local Area Network (LAN) capabilities.
If you have subscribed to phone services from your cable operator then you will be able to
place normal phone calls using your analogue phone and/or fax machine. TCG220‐Tdp provides
one RJ‐11 connector for your phone or home phone system.
TCG220‐Tdp will give you broadband Internet access, telephone connection and wireless
networking all in one unit. Besides that, this residential cable gateway offers Firewall for
additional protection and security and VPN (virtual private network).
Package Contents
Package Contents
TCG220‐Tdp WiFi EMTA
Ethernet Cable
Power Adaptor
QIG
Warranty card
x1
x1
x1
x1
x1
x1
Chapter 2: Overview
Front Panel
The following illustration shows the front panel of the EMTA:
Power
Indicates the Power status.
DS
Indicates the status of Data reception by the cable modem from the Network (Downstream Traffic)
US
Indicates the status of Data transmission by the cable modem to the Network (Upstream Traffic)
Online
Ethernet
Displays the status of your cable connection. The light is off when no cable connection is detected
and fully lit when the modem has established a connection with the network and data can be
transferred
Indicates the state of Ethernet ports
WIFI
Indicates the traffic on the wireless network
WPS
Indicates the status of the WPS functionality
TEL
Indicates the status of the telephone Phone
There will be 9 LEDs on PKE1320SW‐D112(US‐Tdp‐RoHS) / TCG220‐TdP, but DS and US are bi‐color LED. Looking
at LED from top to bottom: Power, DS(bi‐color), US(bi‐color), Online, Ethernet 1,2, WiFi , WPS, TEL.
Power Up
DS
DS1
US
US1
Power
(green
color)
(blue
color)
(green
color)
(blue
color)
Online
Eth1
Eth2
Wifi
WPS
TEL
ON
Indicate Power On or OFF
Firmware
fail
Flash
If during this process, the FW isn't in the
CPE or there is a FW error and the CPE
isn't going to be able to boot, one of the
led will blinking.
Connect
LAN1
ON
ON
When CPE device (PC) is connect to
LAN1
LAN1
traffic
ON
Flash
When there is traffic, Eth1 LED will flash.
Connect
LAN2
ON
ON
When CPE device (PC) is connect to
LAN2
LAN2
traffic
ON
Flash
When there is traffic, Eth2 LED will flash.
CM boot
cycle
ON
Flash
OFF
Flash
OFF
Flash
OFF
From Power
complete
ON
Flash
OFF
OFF
OFF
OFF
OFF
During DS scanning and acquiring SYNC
ON
ON
OFF
OFF
OFF
OFF
OFF
Complete synchronization of primary DS
ON
ON
ON
OFF
OFF
OFF
OFF
Register as DS bonding mode(2ch or
more)
ON
ON
ON
Flash
OFF
OFF
OFF
After primary DS locked, process of
ranging
ON
ON
ON
ON
OFF
OFF
OFF
Ranging complete
ON
ON
ON
ON
ON
OFF
OFF
Register as US bonding mode(2ch or
more)
ON
ON
ON
ON
ON
Flash
OFF
After US ranging complete, process of
communication
between
DOCSIS
provision server
ON
ON
ON
ON
ON
ON
OFF
CM online(Operational)
ON
ON
ON
ON
Flash
MTA provision
ON
ON
ON
ON
ON
ON
Flash
Flash
During SW upgrade
DOCSIS
operation
MTA
operation
Flash
upgrade
on to
system initial
MTA online(Operation)
Factory
reset
Flash
Flash
Flash
Flash
When performing factory reset, the
device shall feedback to the user by a
2Hz blinking for during the perform of
the factory reset
WiFi
enable
ON
When WiFi is enabled, the WiFi LED will
ON.
WiFi
disable
OFF
When WiFi is disabled, the WiFi LED will
OFF.
WiFi
traffic
Flash
When there is traffic, the WiFi LED will
Flash.
WPS
Running
Flash
When there is a long press (>5seconds),
the WPS process will initiate and the
WPS LED will start to Flash.
WPS idle
OFF
Rear Panel Connector Description
Slot
Description
12VDC
CABLE
RESET
ETHERNET 1 2
TEL
12V DC‐IN Power connector
F‐Connector
Reset/Reboot this Cable modem
Ethernet 10/100/1000 BaseT RJ‐45 connector
Telephony RJ‐11 connector
Side Panel for WPS
WPS – Indicates the status of the WPS (Wi‐Fi Protected SetupTM) functionality.
There is one WPS button on the Top Side Panel of TCG220‐Tdp and is designed to have multiple function. This
button can be used to:
Securely and Simply Get WiFi Client Connected: WPS button can be used to pairing WiFi client which also
supports WPS function. A long press (press more than 5 seconds) on the WPS button will enable
TCG220‐Tdp scan for any available WPS device.
Note: You must ensure that the WiFi client device supports WPS function in order to use this WPS
function on TCG220‐TdP.
3. Connecting the Residential VoIP cable modem to Your Computer
Installation Procedure for Ethernet Interface
Follow the steps below for proper installation:
1. Connect one end of the coaxial cable to the CABLE connection on the wall, and the other
end to the CABLE jack on the TCG220‐Tdp.
Note: To speed up the registration process of cable modem, the coaxial cable should be
connected to the modem before the modem turned ON
2. Connect the plug from the power supply into the POWER jack on the TCG220‐Tdp, and
plug the power supply into an AC outlet.
Note: Use only the power supply that accompanied this unit. Using other adapters may
damage the unit.
3. Connect one end of the Ethernet cable to the Ethernet port of your computer, and the
other end to the ETHERNET port on the TCG220‐Tdp.
4. The TCG220‐Tdp will look for the proper cable modem signal in the Cable Television
network and process the initial registration. The voice gateway is ready for data transfer
after the LED “Cable Link” is lit solid green.
Note: The REBOOT button at the rear panel is for maintenance purposes only. You don’t
need to use it.
Fig. How to set up your connection
CAUTION for UL
North American Cable Installer:
This reminder is provided to call your attention to Article 820.93 of the National Electrical Code (Section 54
of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the building as close to the
point of cable entry as practical.
This symbol on your set guarantees that your product complies with the European
Directives 1999/5/EC and 2009/125/EC on Safety, Telecom, Electromagnetic
Compatibility and Energy using Products.
Federal Communication Commission Interference
Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
‐
Reorient or relocate the receiving antenna.
‐
Increase the separation between the equipment and receiver.
‐
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
‐
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Note: The country code selection is for non‐US model only and is not available to all US model. Per FCC
regulation, all WiFi product marketed in US must fixed to US operation channels only.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2015:11:13 18:25:47+08:00
Create Date                     : 2015:11:13 18:16:36+08:00
Metadata Date                   : 2015:11:13 18:25:47+08:00
Format                          : application/pdf
Title                           : Microsoft Word - QIG-PKE1320SW-D112_US-Tdp-RoHS__TCG220-Tdp_V1.0  20151113
Creator                         : nilin
Document ID                     : uuid:5b717e3c-c710-456c-a015-81bed8bf195f
Instance ID                     : uuid:5d783c9d-80a9-4ef0-ade2-c97884d24f11
Page Count                      : 8
Author                          : nilin

EXIF Metadata provided by EXIF.tools