Askey Computer WLU5153 Wireless Module User Manual

THE FOLLOWING APPLIES IN THE U.S.A. AND CANADA

This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation of this device.

This transmitter must not be co-located or operated in conjunction with any other antenna or

transmitter.

low power wireless devices.

There is no proof, however, that these low power wireless devices are absolutely safe.

Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range

while being used.

Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF

that does not produce heating effects causes no known adverse health effects.

Many studies of low-level RF exposures have not found any biological effects. Some studies have

suggested that some biological effects might occur, but such findings have not been confirmed by

additional research.

Wireless LAN adaptor has been tested and found to comply with FCC/IC radiation exposure limits

Federal Communication Commission Interference Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause

undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

users, and

As long as 2 conditions above are met, further transmitter test will not be required.

However, the OEM integrator is still responsible for testing their end-product for any

additional compliance requirements required with this module installed

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may be

installed such that 20 cm may be maintained between the antenna and users. The final end

product must be labeled in a visible area with the following: “Contains FCC ID: H8N-WLU5153”.

The grantee's FCC ID can be used only when all FCC compliance requirements are met.

Manual Information To the End User

The end user manual shall include all required regulatory information/warning as show in this

manual.

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne

doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y

compris un brouillage susceptible de provoquer un fonctionnement indésirable.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

device use)

1) The antenna must be installed such that 20 cm is maintained between the antenna and users,

2) The transmitter module may not be co-located with any other transmitter or antenna.

As long as 2 conditions above are met, further transmitter test will not be required. However, the

OEM integrator is still responsible for testing their end-product for any additional compliance

requirements required with this module installed.

Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour

seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son

produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé.

In the event that these conditions can not be met (for example certain laptop configurations or

and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will

be responsible for re-evaluating the end product (including the transmitter) and obtaining a

separate Canada authorization.

NOTE IMPORTANTE:

Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations

d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du

labeled in a visible area with the following: “Contains IC: 1353A-WLU5153

Plaque signalétique du produit final

Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne

peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et

les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:

“Contains IC: 1353A-WLU5153

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to

L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à

la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui

intègre ce module.

Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et

avertissements comme indiqué dans ce manuel.

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the

potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725

MHz shall comply with the e.i.r.p. limit; and

(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with

the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.

users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause

satellites mobiles utilisant les mêmes canaux;

(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5

(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit

se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point,

selon le cas.

puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5

250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des

dommages aux dispositifs LAN-EL.

NCC

第十二條→經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不得擅自變更頻

率、加大功率或變更原設計之特性及功能。

第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立

即停用，並改善至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科

無線資訊傳設備的製造廠商應確保頻率穩定性，如依製造廠商使用手冊上所述正常操作，發射的信

號應維持於操作頻帶中。(4.7.7)

本模組於取得認證後將依規定於模組本體標示審驗合格標籤。

Be aware of the following limits before using the Wireless Module.

●To use the Wireless Module, an access point needs to be obtained.

●Do not use the Wireless Module to connect to any wireless network (SSID∗) for which you do not have

usage rights. Such networks may be listed as a result of searches. However, using them may be regarded

as illegal access.

●Do not subject the Wireless Module to high temperatures, direct sunlight or moisture.

●Do not bend, or subject the Wireless Module to strong impacts.

●Do not disassemble or alter the Wireless Module in any way.

●Do not attempt to install the Wireless Module in any incompatible device.

●Do not remove the Wireless Module from the host product during operations.

●Data transmitted and received over radio waves may be intercepted and monitored.

●Depending on the area, this Wireless Module may not be available.

Confirm the encryption key, settings and positions of your access point before starting setup. For

details, read the manual of the access point.

Select your desired access point.

Enter the PIN code to the access point, and then select.

(3-3) Search for access point

Access points found automatically are listed.

Select your desired access point.

Access the encryption key input mode.

Enter the encryption key of the access point.

(3-4) Manual