Askey Computer WLU5153 Wireless Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2056698
Application ID	4+BYciZbEHBhZAPS2p2ibQ==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	44.58kB (557205 bits)
Date Submitted	2013-08-29 00:00:00
Date Available	2014-02-25 00:00:00
Creation Date	2013-08-29 16:31:55
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2013-08-29 16:55:20
Document Title	User Manual.pdf
Document Creator	Microsoft® Office Word 2007
Document Author:	松田幸子

ENGLISH
THE FOLLOWING APPLIES IN THE U.S.A. AND CANADA
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation of this device.
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
This product is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range.
FCC and IC require this product to be used indoors for the frequency range 5.15 to 5.25 GHz to
reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power
radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These
radar stations can cause interference with and/or damage this product.
The available scientific evidence does not show that any health problems are associated with using
low power wireless devices.
There is no proof, however, that these low power wireless devices are absolutely safe.
Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range
while being used.
Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF
that does not produce heating effects causes no known adverse health effects.
Many studies of low-level RF exposures have not found any biological effects. Some studies have
suggested that some biological effects might occur, but such findings have not been confirmed by
additional research.
Wireless LAN adaptor has been tested and found to comply with FCC/IC radiation exposure limits
set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
Federal Communication Commission Interference Statement :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient
or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
-Connect
the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult
the dealer or an experienced host product technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and
users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain
laptop configurations or co-location with another transmitter), then the FCC authorization
is no longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following: “Contains FCC ID: H8N-WLU5153”.
The grantee's FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
THE FOLLOWING APPLIES ONLY IN CANADA.
This Class B digital apparatus complies with Canadian ICES-003.
Product Identification Marking is located on the top of the Wireless Module.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio
exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne
doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y
compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions: (For module
device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour
utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre
l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne
seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son
produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or
co-location with another transmitter), then the Canada authorization is no longer considered valid
and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and obtaining a
separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du
Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans
ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur)
et l'obtention d'une autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product must be
labeled in a visible area with the following: “Contains IC: 1353A-WLU5153
”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne
peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et
les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
“Contains IC: 1353A-WLU5153
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à
la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui
intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manuel.
Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725
MHz shall comply with the e.i.r.p. limit; and
(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with
the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.
(iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority
users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause
interference and/or damage to LE-LAN devices.
Avertissement:
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les
restrictions susmentionnées, notamment :
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5
470-5 725 MHz doit se conformer à la limite de p.i.r.e.;
(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit
se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point,
selon le cas.
(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute
puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5
250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des
dommages aux dispositifs LAN-EL.
NCC
802.11b/802.11g/BT 警語：
第十二條→經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科
學及醫療用電波輻射性電機設備之干擾。
802.11a 警語：
在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。 (4.7.5)
無線資訊傳輸設備忍受合法通信之干擾且不得干擾合法通信；如造成干擾，應立即停用，俟無干擾
之虞，始得繼續使用。 (4.7.6)
無線資訊傳設備的製造廠商應確保頻率穩定性，如依製造廠商使用手冊上所述正常操作，發射的信
號應維持於操作頻帶中。(4.7.7)
本模組於取得認證後將依規定於模組本體標示審驗合格標籤。
系統廠商應於平台上標示「本產品內含射頻模組：
XXXyyyLPDzzzz-x (NCC ID)」字樣。
Caution
Be aware of the following limits before using the Wireless Module.
●To use the Wireless Module, an access point needs to be obtained.
●Do not use the Wireless Module to connect to any wireless network (SSID∗) for which you do not have
usage rights. Such networks may be listed as a result of searches. However, using them may be regarded
as illegal access.
∗SSID is a name for identifying a particular wireless network for transmission.
●Do not subject the Wireless Module to high temperatures, direct sunlight or moisture.
●Do not bend, or subject the Wireless Module to strong impacts.
●Do not disassemble or alter the Wireless Module in any way.
●Do not attempt to install the Wireless Module in any incompatible device.
●Do not remove the Wireless Module from the host product during operations.
●Data transmitted and received over radio waves may be intercepted and monitored.
●To avoid malfunctions caused by radio wave interface, keep the host product away from the devices
such as other wireless LAN devices, microwaves and the devices that use 2.4 GHz and 5 GHz signals
when using the Wireless Module.
●When noises occur due to the static electricity, etc., the host product might stop operating for the
protection of the devices. In this case, turn the host prodcut Off with Mains power On / Off switch, then
turn it On again.
●Depending on the area, this Wireless Module may not be available.
Setup the wireless LAN connection
Confirm the encryption key, settings and positions of your access point before starting setup. For
details, read the manual of the access point.
(1) connect the Wireless LAN Adaptor to the USB port.
(2) Select the connection type and set.
Connection Type
WPS(Push button)
WPS(PIN)
Search for access point
Manual
(3-1) WPS(Push botton)
Press the WPS button on the access point until the light flashes.
And then, press the OK button.
(3-2) WPS(PIN)
Select your desired access point.
Enter the PIN code to the access point, and then select.
(3-3) Search for access point
Access points found automatically are listed.
Select your desired access point.
Access the encryption key input mode.
Enter the encryption key of the access point.
(3-4) Manual
You can setup SSID, authentication type, encryption type, and encryption key manually.
Follow the on screen instructions and set manually.
Specifications
Power supply
DC 5V (USB powered) 500mA
Antenna
Tx 2, Rx 2
Interface
USB 2.0
Standard Compliance
IEEE802.11n / IEEE802.11a / IEEE802.11g / IEEE802.11b
Transmission system
MISO-OFDM system, OFDM system, DSSS system
IEEE802.11n / IEEE802.11a :
Frequency Range*1,*2
5.150GHz - 5.850 GHz
IEEE802.11g / IEEE802.11b / IEEE802.11n:
2.400 GHz - 2.4835 GHz
IEEE802.11n: Tx Max. 300Mbps, Rx Max. 300Mbps
Transfer rate (standard) *3
IEEE802.11g / IEEE802.11a: Max. 54Mbps
IEEE802.11b: Max. 11Mbps
Access Mode
Infrastructure mode
WPA2-PSK (TKIP/AES)
Security
WPA-PSK (TKIP/AES)
WEP (64bit/128bit)
*1 The frequency and channel differ depending on the country.
*2 802.11b/g/n CH1 ~ CH11 only use for North America, Canada, and Taiwan.
*3 Transfer rate are theoretical values; however, actual communication rate will vary according to
communication environment or connected equipment.
MSIP-CRM-H8N-WLU5153-D81

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Annotate, Fill forms
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2013:08:29 16:31:55+08:00
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2013:08:29 16:55:20+08:00
Metadata Date                   : 2013:08:29 16:55:20+08:00
Format                          : application/pdf
Creator                         : 松田幸子
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:c7e91a07-75d9-44a8-a078-5ca29d0bc384
Instance ID                     : uuid:05c069d6-8178-4c65-a9b3-2e7ce84a72cd
Page Count                      : 10
Language                        : zh-TW
Author                          : 松田幸子

EXIF Metadata provided by EXIF.tools