Asus Evo Desktop Motherboard F1A75Vevo Users Manual

F1A75VEVO to the manual 89383204-a175-425c-aade-875c2ea0f716

2015-01-21

: Asus Asus-Asus-Evo-Desktop-Motherboard-F1A75Vevo-Users-Manual-236622 asus-asus-evo-desktop-motherboard-f1a75vevo-users-manual-236622 asus pdf

Open the PDF directly: View PDF .
Page Count: 72

Download
Open PDF In Browser	View PDF

Motherboard

F1A75-V EVO

E6697
First Edition (V1)
June 2011
Copyright © 2011 ASUSTeK Computer Inc. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK Computer Inc. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product may contain copyrighted software that is licensed under the General Public License (“GPL”)
and under the Lesser General Public License Version (“LGPL”). The GPL and LGPL licensed code in this
product is distributed without any warranty. Copies of these licenses are included in this product.
You may obtain the complete corresponding source code (as defined in the GPL) for the GPL Software,
and/or the complete corresponding source code of the LGPL Software (with the complete machinereadable “work that uses the Library”) for a period of three years after our last shipment of the product
including the GPL Software and/or LGPL Software, which will be no earlier than December 1, 2011, either
(1) for free by downloading it from http://support.asus.com/download;
or
(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location
where you want to have it shipped to, by sending a request to:
ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the
product for which you wish to obtain the corresponding source code and your contact details so that we
can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as
the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source
Software licenses. If however you encounter any problems in obtaining the full corresponding source code
we would be much obliged if you give us a notification to the email address gpl@asus.com, stating the
product and describing the problem (please do NOT send large attachments such as source code archives
etc to this email address).

Contents
Notices.......................................................................................................... vi
Safety information...................................................................................... vii
About this guide........................................................................................ viii
F1A75-V EVO specifications summary...................................................... ix

Chapter 1

Product introduction

1.1

Welcome!....................................................................................... 1-1

1.2

Package contents.......................................................................... 1-1

1.3

Special features............................................................................. 1-1
1.3.1

Product highlights............................................................ 1-1

1.3.2

Dual Intelligent Processors 2 – DIGI+ VRM..................... 1-2

1.3.3

ASUS Digital Power Design............................................. 1-3

1.4

Before you proceed...................................................................... 1-6

1.5

Motherboard overview.................................................................. 1-7

1.6

1.7

1.8

1.5.1

Placement direction......................................................... 1-7

1.5.2

Screw holes..................................................................... 1-7

1.5.3

Motherboard layout.......................................................... 1-8

1.5.4

Layout contents................................................................ 1-8

Accelerated Processing Unit (APU)............................................ 1-9
1.6.1

Installing the APU............................................................. 1-9

1.6.2

Installing the heatsink and fan........................................1-11

System memory.......................................................................... 1-12
1.7.1

Overview........................................................................ 1-12

1.7.2

Memory configurations................................................... 1-13

1.7.3

Installing a DIMM........................................................... 1-14

1.7.4

Removing a DIMM......................................................... 1-14

Expansion slots........................................................................... 1-15
1.8.1

Installing an expansion card.......................................... 1-15

1.8.2

Configuring an expansion card...................................... 1-15

1.8.3

PCI slots......................................................................... 1-15

1.8.4

PCI Express 2.0 x1 slots................................................ 1-15

1.8.5

PCI Express 2.0 x16 slots.............................................. 1-15

1.9

Jumpers....................................................................................... 1-16

1.10

Connectors.................................................................................. 1-17
1.10.1

Rear panel ports............................................................ 1-17

1.10.2

Internal connectors........................................................ 1-19

iii

Contents
1.11

Onboard switch........................................................................... 1-25

1.12

Onboard LEDs............................................................................. 1-28

1.13

Software support......................................................................... 1-30
1.13.1

Installing an operating system....................................... 1-30

1.13.2

Support DVD information............................................... 1-30

Chapter 2
2.1

2.1.1

ASUS Update utility......................................................... 2-1

2.1.2

ASUS EZ Flash 2............................................................. 2-2

2.1.3

ASUS CrashFree BIOS 3 utility....................................... 2-3

2.1.4

ASUS BIOS Updater........................................................ 2-4

2.2

BIOS setup program..................................................................... 2-7

2.3

Main menu................................................................................... 2-11

2.4

2.5

BIOS information

Managing and updating your BIOS............................................. 2-1

2.3.1

System Language [English]............................................2-11

2.3.2

System Date [Day xx/xx/xxxx].........................................2-11

2.3.3

System Time [xx:xx:xx]...................................................2-11

2.3.4

Security...........................................................................2-11

Ai Tweaker menu......................................................................... 2-13
2.4.1

Ai Overclock Tuner [Auto].............................................. 2-14

2.4.2

Memory Frequency [Auto].............................................. 2-14

2.4.3

APU Multiplier [Auto]...................................................... 2-14

2.4.4

EPU Power Saving Mode [Disabled]............................. 2-14

2.4.5

OC Tuner....................................................................... 2-15

2.4.6

DRAM Timing Control.................................................... 2-15

2.4.7

CPU Voltage [Offset Mode]............................................ 2-15

2.4.8

DRAM Voltage [Auto]..................................................... 2-16

2.4.9

SB 1.1V Voltage [Auto].................................................. 2-16

2.4.10

1.1Vsb Voltage [Auto].................................................... 2-16

2.4.11

APU1.2V Voltage [Auto]................................................. 2-16

2.4.12

VDDA Voltage [Auto]...................................................... 2-16

2.4.13

DIGI + VRM.................................................................... 2-16

2.4.14

APU Spread Spectrum [Auto]........................................ 2-17

Advanced menu.......................................................................... 2-18
2.5.1

CPU Configuration......................................................... 2-18

2.5.2

SATA Configuration........................................................ 2-19

Contents

2.6

2.5.3

USB Configuration......................................................... 2-19

2.5.4

NB Configuration............................................................ 2-20

2.5.5

Onboard Devices Configuration..................................... 2-20

2.5.6

APM............................................................................... 2-21

Monitor menu.............................................................................. 2-22
2.6.1

CPU Temperature / MB Temperature [xxxºC/xxxºF]....... 2-23

2.6.2 CPU / Chassis / Power Fan Speed [xxxx RPM] or
[Ignore] / [N/A].......................................................

2.7

2.8

2.9

2-23

2.6.3

CPU Q-Fan Control [Disabled]....................................... 2-23

2.6.4

Chassis Q-Fan Control [Disabled]................................. 2-24

2.6.5

CPU Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage... 2-24

2.6.6

Anti Surge Support [Enabled]........................................ 2-24

Boot menu................................................................................... 2-25
2.7.1

Bootup NumLock State [On].......................................... 2-25

2.7.2

Full Screen Logo [Enabled]............................................ 2-25

2.7.3

Wait for ‘F1’ If Error [Enabled]........................................ 2-25

2.7.4

Option ROM Messages [Force BIOS]............................ 2-26

2.7.5

Setup Mode [EZ Mode].................................................. 2-26

2.7.6

Boot Option Priorities..................................................... 2-26

2.7.7

Boot Override................................................................. 2-26

Tools menu.................................................................................. 2-27
2.8.1

ASUS EZ Flash 2 Utility................................................. 2-27

2.8.2

ASUS O.C. Profile.......................................................... 2-27

2.8.3

ASUS SPD Information.................................................. 2-27

Exit menu..................................................................................... 2-28

Notices
Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference, and
•

This device must accept any interference received including interference that may cause
undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.

•

Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.

Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
This class B digital apparatus complies with Canadian ICES-003.

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs come from our commitment to the highest standards
for protecting our environment. We believe in providing solutions for you to be able to
responsibly recycle our products, batteries, other components as well as the packaging
materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed recycling
information in different regions.

REACH

Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
ASUS REACH website at http://csr.asus.com/english/REACH.htm.
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.

Safety information
Electrical safety
•

To prevent electric shock hazard, disconnect the power cable from the electric outlet
before relocating the system.

•

When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.

•

Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.

•

Seek professional assistance before using an adapter or extension cord. These devices
could interrupt the grounding circuit.

•

Ensure that your power supply is set to the correct voltage in your area. If you are not
sure about the voltage of the electrical outlet you are using, contact your local power
company.

•

If the power supply is broken, do not try to fix it by yourself. Contact a qualified service
technician or your retailer.

Operation safety
•

Before installing the motherboard and adding devices on it, carefully read all the manuals
that came with the package.

•

Before using the product, ensure that all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.

•

To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.

•

Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may become wet.

•

Place the product on a stable surface.

•

If you encounter technical problems with the product, contact a qualified service
technician or your retailer.

vii

About this guide
This user guide contains the information you need when installing and configuring the
motherboard.

How this guide is organized

This guide contains the following parts:
• Chapter 1: Product introduction

This chapter describes the features of the motherboard and the new technology it
supports.

•

Chapter 2: BIOS information

This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.

Conventions used in this guide

To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.

DANGER/WARNING: Information to prevent injury to yourself when trying to
complete a task.

CAUTION: Information to prevent damage to the components when trying to
complete a task.

IMPORTANT: Instructions that you MUST follow to complete a task.

NOTE: Tips and additional information to help you complete a task.

Where to find more information

Refer to the following sources for additional information and for product and software
updates.
1.

ASUS websites

The ASUS website provides updated information on ASUS hardware and software
products. Refer to the ASUS contact information.

Optional documentation

Your product package may include optional documentation, such as warranty flyers,
that may have been added by your dealer. These documents are not part of the
standard package.

Typography
Bold text

Italics

viii

Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
Keys enclosed in the less-than and greater-than sign means
that you must press the enclosed key.
Example: means that you must press the Enter or
Return key.
If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).
Example: ++

F1A75-V EVO specifications summary
APU

AMD® A- & E2- series accelerated processors with AMD®
Radeon™ HD 6000 series graphics, up to 4 CPU cores, FM1
package
AMD® Turbo Core Technology 2.0 support
DirectX® 11 Support
* The AMD® Turbo Core Technology 2.0 support depends on the
APU types.
** Refer to www.asus.com for the AMD® APU support list

Chipset

AMD® A75 FCH (Hudson D3)

Memory

Dual-channel memory architecture
4 x 240-pin DIMM slots support maximum 64GB unbuffered
non-ECC DDR3 1866/1600/1333/1066 MHz memory modules
* The maximum 64GB memory capacity can be supported with
16GB or above DIMMs. ASUS will update the memory QVL
once the DIMMs are available in the market.
** Refer to www.asus.com for the latest Memory QVL (Qualified
Vendors List).
*** When you install a total memory of 4GB capacity or more,
Windows® 32-bit operating system may only recognize less
than 3GB. We recommend a maximum of 3GB system memory
if you are using a Windows® 32-bit operating system.

Graphics

Integrated AMD® Radeon™ HD 6000 series graphics in the LIano
APU
Multi-VGA output support: DisplayPort, HDMI, DVI-D, D-Sub port
- Supports DisplayPort with max. resolution 2560 x 1600 @60Hz
- Supports HDMI with max. resolution up to 1920 x 1200 @60Hz
- Supports single-link DVI with max. resolution up to 1920 x 1200
@60Hz
- Supports D-Sub with max. resolution up to 1920 x 1600 @60Hz
- Supports Microsoft® DirectX 11
Supports AMD® Dual Graphics
*R
efer to www.amd.com for the discrete GPUs that support Dual
Graphics.

Expansion slots

2 x PCIe 2.0 x16 slots (Single @x16 or dual @x8 / x8 mode)
1 x PCIe 2.0 x16 slots (black, max. @x4 mode)
2 x PCIe 2.0 x1 slots
2 x PCI slots
* The PCIe x16_3 slot shares bandwidth with PCIe x1_2 slot.
Due to the CrossFireXTM limitation, DO NOT use the PCIe x1_2
slot when you install two CrossfireXTM graphic cards on both
the PCIe x16_1 and PCIe x16_3 slots to set up a CrossFireXTM
configuration.

LAN

Realtek® RTL8111E PCIe Gigabit LAN controller

(continued on the next page)

F1A75-V EVO specifications summary

Storage

AMD® A75 FCH southbridge:
- 6 x Serial ATA 6.0Gb/s connectors (gray) support RAID 0,
RAID 1, RAID 10 and JBOD configurations
Asmedia® PCIe SATA 6Gb/s controller:
- 1 x Serial ATA 6Gb/s connector (navy blue)
- 1 eSerial ATA 6Gb/s at the back I/O

Audio

ALC892 8-channel High Definition Audio CODEC
- Supports Jack-Detection, Multi-Streaming, and Front
Panel Jack-Retasking
- Supports S/PDIF out interface at the back I/O

USB

AMD® A75 FCH southbridge:
- 10 x USB 2.0/1.1 ports (8 ports at the front panel, 2
ports at the back panel)
- 4 x USB 3.0 ports (2 ports at the front panel, 2 ports at
the back panel) (blue)
Asmedia® PCIe USB3.0 controller:
- 2 x USB 3.0/2.0 ports (at the back panel)

ASUS unique
features

ASUS Dual Intelligent Processors II with DIGI+ VRM
- ASUS TPU: Auto Tuning, TurboV and TPU switch
- ASUS EPU: EPU, EPU switch
ASUS Digital Power Design
- Industry leading Digital 6+2 Phase Power Design
ASUS Exclusive Features
- MemOK!
- ASUS AI Suite II
- AI Charger+
- ASUS Anti-Surge Protection
- ASUS UEFI BIOS EZ Mode featuring graphics user interface
ASUS Quiet Thermal Solution
- ASUS Fanless Design: Stylish heat-pipe solution
- ASUS Fan Xpert
ASUS EZ DIY
- ASUS Q-Shield, Q-Slot, Q-Connector
- ASUS CrashFree BIOS 3
- ASUS EZ Flash 2
- ASUS MyLogo 2™
- Multi-language BIOS

Back Panel I/O
ports

1 x PS/2 keyboard / mouse combo port
1 x DisplayPort
1 x HDMI port
1 x DVI-D port
1 x D-Sub port
1 x Optical S/PDIF port
1 x LAN (RJ-45) port
1 x eSATA port
2 x USB 2.0/1.1 ports
4 x USB 3.0 ports
8-channel audio 6 Jacks

F1A75-V EVO specifications summary
Special features

100% All high quality conductive polymer capacitors

ASUS exclusive
overclocking
features

Intelligent overclocking tools:
- TPU Switch
- Auto Tuning
Precision Tweaker 2
- vCore: Adjustable CPU voltage at 0.00625V
increment
- vDRAM Bus: Adjustable DRAM voltage at 0.01V increment
- vFCH: Adjustable FCH voltage at 0.01V increment
SFS (Stepless Frequency Selection):
- PCIe frequency tuning from 100MHz up to 200MHz at
1MHz increment
Overclocking Protection:
- ASUS C.P.R

Internal I/O
connectors / buttons
/ switches

4 x USB 2.0/1.1 connectors support additional 8 USB
2.0/1.1 ports
1 x USB 3.0 connector supports additional 2 USB 3.0 ports
7 x SATA 6.0Gb/s connectors (6 x gray, 1 x navy blue)
1 x COM connector
1 x CPU fan connector
2 x Chassis fan connectors
1 x Power fan connector
1 x High Definition front panel audio connector
1 x S/PDIF output connector
1 x System panel connector
1 x 24-pin EATX power connector
1 x 8-pin ATX 12V power connector
1 x MemOK! button
1 x EPU switch
1 x TPU switch

BIOS

32Mb Flash ROM, UEFI BIOS, PnP, DMI 2.0, WfM 2.0,
ACPI V2.0a, SM BIOS 2.6

Accessories

2 x Serial ATA 6.0Gb/s cables
1 x Q-Shield
1 x Q-Connector (retail version only)
1 x User Manual
1 x Support DVD

Support DVD

Drivers
ASUS Update
ASUS utilities
Anti-Virus software (OEM version)

Form factor

ATX form factor: 12 in x 9.6 in (30.5 cm x 24.4 cm)

*Specifications are subject to change without notice.

xii

Chapter 1

Product introduction
1.1

Welcome!

Thank you for buying an ASUS® F1A75-V EVO motherboard!
The motherboard delivers a host of new features and latest technologies, making it another
standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it, check the items in
your package with the list below.

1.2

Package contents

Check your motherboard package for the following items.
Motherboard
Cables
Accessories

Application DVD
Documentations

ASUS F1A75-V EVO motherboard
2 x Serial ATA 6.0Gb/s cables
1 x Q-Shield
1 x Q-Connector (retail version only)
ASUS motherboard Support DVD
User Manual

If any of the above items is damaged or missing, contact your retailer.

1.3

Special features

1.3.1

Product highlights
AMD® A- & E2- series accelerated processors with AMD®
Radeon™ HD 6000 series graphics
This motherboard supports AMD® A- & E2- series accelerated processor
with AMD® Radeon™ HD 6000 series graphics. This revolutionary APU
(Accelerated Processing Unit) combines processing power and advanced
DirectX 11 graphics in one small, energy-efficient design to enable
accelerated performance and an industry-leading visual experience.
It features Dual-channel DDR3 memory support and accelerates data
transfer rate up to 5GT/s.

ASUS F1A75-V EVO

1-1

AMD® A75 FCH (Hudson D3) Chipset
AMD® A75 FCH (Hudson D3) is designed to support up to 5GT/s interface
speed and PCI Express™ 2.0 x 16 (at x4 speed) graphics. It supports 6 x
SATA 6Gb/s ports and 4 x USB 3.0 Ports.

ATI® CrossFireX™ Technology
ATI’s CrossFireX™ boosts image quality along with rendering speed,
eliminating the need to scale down screen resolution to get high quality
images. CrossFireX™ allows higher antialiasing, anisotropic filtering,
shading, and texture settings. Adjust your display configurations,
experiment with the advanced 3D settings, and check the effects with a
real-time 3D-rendered previews within ATI Catalyst™ Control Center.

USB 3.0 support
Experience ultra-fast data transfer at 4.8Gbps with USB 3.0 – the latest
connectivity standard. Built to connect easily with next-generation
components and peripherals, USB 3.0 transfers data 10x faster and is
also backward compatible with USB 2.0 components.

Native SATA 6.0 Gb/s support
The AMD® A75 FCH natively supports next-generation Serial ATA (SATA)
storage interface, this motherboard delivers up to 6.0 Gb/s data transfer
rates. Additionally, get enhanced scalability, faster data retrieval, double
the bandwidth of current bus systems.

100% All High-quality Conductive Polymer Capacitors
This motherboard uses all high-quality conductive polymer capacitors for
durability, improved lifespan, and enhanced thermal capacity.

1.3.2

Dual Intelligent Processors 2 – DIGI+ VRM
The world’s first Dual Intelligent Processors from ASUS pioneered the use
of two onboard chips - TPU (TurboV Processing Unit) and EPU (Energy
Processing Unit). Its new generation of Dual Intelligent Processors 2
with DIGI+ VRM launches power delivery into a digital standard with
a programmable microprocessor that perfectly serves power signal,
eliminating digital-to-analog conversion lag. It’s the most precise power
delivery available providing the best in class power efficiency, greater
performance, and rock solid stability. With ASUS DIGI+ VRM, users can
easily adjust power phase performance and system voltages via diverse
settings to maximize overall performance and overclocking potential.

TPU
Unleash your performance with ASUS’ simple onboard switch or AI Suite
II utility. ASUS Auto tuning feature can automatically optimize the system
for fast, yet stable clock speeds, and the TurboV gives you the freedom
to adjust APU Multiplier to optimize performance under varied system
conditions.

1-2

Chapter 1: Product introduction

EPU
Tap into the world’s first real time PC power saving engine through
a simple onboard switch or AI Suite II utility. Get total system-wide
energy optimization by automatically detecting current PC loadings and
intelligently moderating power consumption. This also reduces fan noise
and extends component longevity.

1.3.3

ASUS Digital Power Design
DIGI+ VRM
The world’s first Dual Intelligent Processors from ASUS pioneered the
use of two onboard chips - TPU (TurboV Processing Unit) and EPU
(Energy Processing Unit). New generation Dual Intelligent Processors 2
with DIGI+ VRM launch power delivery into a digital standard. It features
a digital programmable microprocessor onboard to perfectly match digital
power signal, eliminating digital-to-analog conversion lag, The precise
power delivery minimizes power transfer loss to provide highest power
efficiency, greater performance , and rock solid stability with the most
flexible power adjustment than traditional analog power design.With
ASUS DIGI+ VRM, users can easily adjust power phase management
voltages and frequency modulation via diverse settings through BIOS
tunings and the exclusive user interface. It increases overclocking range
while performance reaches its full potential.

1.3.4

ASUS Exclusive Features
ASUS TurboV
Feel the adrenaline rush of real-time OC-now a reality with the ASUS
TurboV. This easy OC tool allows you to overclock without exiting or
rebooting the OS; and its user-friendly interface makes overclock with just
a few clicks away. Moreover, the ASUS OC profiles in TurboV provides
the best O.C. settings in different scenarios.

Auto Tuning
Auto Tuning is an intelligent tool that automates overclocking to achieve
a total system level up. This tool also provides stability testing. Even O.C.
beginners can achieve extreme yet stable overclocking results with Auto
Tuning!

MemOK!
MemOK! guickly ensures memory boot compatibility. This remarkable
memory rescue tool requires a mere push of the button to patch memory
issues. MemOK! determines failsafe settings and dramatically improves
your system boot success. Get your system up and running in no time.

ASUS F1A75-V EVO

1-3

ASUS UEFI BIOS (EZ Mode)
The new ASUS UEFI BIOS is an Unified Extensible Firmware Interface
that offers a user-friendly interface that goes beyond traditional keyboardonly BIOS controls to enable more flexible and convenient mouse input.
Users can easily navigate the new UEFI BIOS with the same smoothness
as their operating system. It natively supports hard drives larger than
2.2TB in 64-bit, with full storage space utilization, helping deliver far more
exciting computing than traditional BIOS versions.
The exclusive EZ Mode displays frequently-accessed setup info, while
the Advanced Mode is for experienced performance enthusiasts that
demand far more intricate system settings.

ASUS Anti-Surge Protection
This special design protects expensive devices and the motherboard
from damage caused by power surges from switching power supply unit
(PSU).

AI Suite II
With its fast user-friendly interface, ASUS AI Suite II consolidates all the
exclusive ASUS features into one simple to use software package. It
allows you to supervise overclocking, energy management, fan speed
control, and voltage and sensor readings. This all-in-one software offers
diverse and ease to use functions, with no need to switch back and forth
between different utilities.

Ai Charger+
ASUS Ai Charger+, the latest Ai Charger* version, brings you to a new
level of USB3.0 fast charging experience. With its easy and user-friendly
interface, you can not only easily charge iPod, iPhone and iPad, but also
BC 1.1** standard mobile devices three times*** as fast as before.
* Ai Charger is ASUS unique fast-charging software which supports iPod, iPhone and
iPad.
** Check your USB mobile device manufacturer if it fully supports the BC 1.1 function.
*** The actual charging speed may vary with your USB device’s conditions.

Fanless Design: stylish heatpipe solution
The stylish heatpipe features a 0-dB thermal solution that offers users
a noiseless PC environment. Not only the beautiful shape upgrades the
visual enjoyment for motherboard users, but also the heatsink design
lowers the temperature of the chipset and power phase area through
high efficient heat-exchange. Combined with usability and aesthetics,
the ASUS stylish heatpipe will give users an extremely silent and cooling
experience with the elegant appearance!

1-4

Chapter 1: Product introduction

Fan Xpert
ASUS Fan Xpert intelligently allows you to adjust the CPU fan speed
according to different ambient temperatures caused by different climate
conditions in different geographic regions and your PC’s loading. The
built-in variety of useful profiles offer flexible controls of fan speed to
achieve a quiet and cool environment.

ASUS Q-Design
ASUS Q-Design enhances your DIY experience. All of Q-Shield, Q-Slot
and Q-Connector design speed up and simplify the DIY process!

ASUS Q-Shield
ASUS Q-Shield’s special design makes it convenient and easy to
install on your motherboard. With better electric conductivity, it ideally
protects your motherboard against static electricity and shields it against
Electronic Magnetic Interference (EMI).

ASUS EZ Flash 2
ASUS EZ Flash 2 is a user-friendly utility that allows you to update the
BIOS without using a bootable floppy disk or an OS-based utility.

ASUS MyLogo 2™
Turn your favorite photos into 256-color boot logos to personalize your
system.

ASUS CrashFree BIOS 3
ASUS CrashFree BIOS 3 is an auto-recovery tool that allows you to
restore a corrupted BIOS file using the bundled support DVD or a USB
flash disk that contains the BIOS file.

C.P.R. (CPU Parameter Recall)
The BIOS C.P.R. feature automatically restores the CPU default settings
when the system hangs due to overclocking failure. C.P.R. eliminates the
need to open the system chassis and clear the RTC data. Simply shut
down and reboot the system, and the BIOS automatically restores the
CPU parameters to their default settings.

ErP ready
The motherboard is European Union´s Energy-related Products (ErP)
ready, and ErP requires products to meet certain energy efficiency
requirements in regards to energy consumptions. This is in line with
ASUS vision of creating environment-friendly and energy-efficient
products through product design and innovation to reduce carbon
footprint of the product and thus mitigate environmental impacts.

ASUS F1A75-V EVO

1-5

1.4

Before you proceed

Take note of the following precautions before you install motherboard components or change
any motherboard settings.
• Unplug the power cord from the wall socket before touching any component.
• Before handling components, use a grounded wrist strap or touch a safely grounded
object or a metal object, such as the power supply case, to avoid damaging them due to
static electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded antistatic pad or in the
bag that came with the component.
• Before you install or remove any component, switch off the ATX power supply and
detach its power cord. Failure to do so may cause severe damage to the motherboard,
peripherals, or components.

1-6

Chapter 1: Product introduction

1.5

Motherboard overview

1.5.1

Placement direction

1.5.2

Screw holes

When installing the motherboard, ensure that you place it into the chassis in the correct
orientation. The edge with external ports goes to the rear part of the chassis as indicated in
the image below.

Place nine screws into the holes indicated by circles to secure the motherboard to the
chassis.
DO NOT overtighten the screws! Doing so can damage the motherboard.

Place this side towards
the rear of the chassis.

F1A75-V EVO

ASUS F1A75-V EVO

1-7

1.5.3

Motherboard layout
1

24.4cm(9.6in)

KB_USB3_34

CPU_FAN

EATX12V

5
6
EPU

DDR3 DIMM_B2 (64bit, 240-pin module)

7
8

TPU

CHA_FAN2 DRAM_LED

DDR3 DIMM_B1 (64bit, 240-pin module)

ESATA6G
_USB3_12

DDR3 DIMM_A2 (64bit, 240-pin module)

DVI_VGA

SOCKET FM1

SPDIFO
_HDMI
_DP

DDR3 DIMM_A1 (64bit, 240-pin module)

DIGI+VRM
EPU

ASM
1042

MemOK!

10
1
2

AUDIO
PWR_FAN

CHA_FAN1

PCIEX1_1

EATXPWR

USB3_56

Lithium Cell
CMOS Power

30.5cm(12.0in)

LAN1_USB12

RTL
8111E

PCIEX16_1

SATA6G_E1

Super
I/O

SATA6G_1 SATA6G_3 SATA6G_5
SATA6G_2 SATA6G_4 SATA6G_6

PCIEX1_2

ICS
477D

F1A75-V EVO

AMD®
A75 FCH

PCI1

PCIEX16_2

TPU

PCI2

32Mb
BIOS

PCIEX16_3

ALC
892

SPDIF_OUT

COM1

SB_PWR

USB78

USB910

USB34

USB56

CLRTC

PANEL

AAFP

1.5.4

1-8

Layout contents

Connectors/Jumpers/Slots/LED

Page Connectors/Jumpers/Slots/LED

Page

1. Power, CPU and chassis fan connectors

(3-pin PWR_FAN, 4-pin CPU_FAN,

and 4-pin CHA_FAN1/2)

1-19

11. USB 3.0 connector (20-1 pin USB3_56)

1-27

2. ATX power connectors (24-pin EATXPWR,

8-pin EATX12V)

1-20

12. SATA 6.0Gb/s connectors (7-pin SATA6G_E1,
SATA 6G 1~6)

1-21

3. AMD FM1 socket

1-9

13. Standby power LED (SB_PWR)

1-22

4. DDR3 DIMM slots

1-12

14. System panel connector (20-8 pin PANEL)

1-16

5. TPU LED (ELED730)

1-27

15. Clear RTC RAM (3-pin CLRTC)

1-24

6. EPU LED (ELED740)

1-28

16. USB 2.0 connectors (10-1 pin USB3~10)

1-24

7. EPU switch

1-26

17. Serial port connector (10-1 pin COM1)

1-21

8. TPU switch

1-26

18. Front panel audio connector (10-1 pin AAFP)

1-23

9. MemOK! switch

1-25

19. Digital audio connector (4-1 pin SPDIF_OUT)

1-23

10. DRAM LED (DRAM_LED)

1-27

Chapter 1: Product introduction

1.6

Accelerated Processing Unit (APU)

This motherboard comes with an FM1 socket designed for AMD® A- & E2- series accelerated
processors with AMD® Radeon™ HD 6000 series graphics.
Ensure that you use a APU designed for the FM1 socket. The APU fits in only one correct
orientation. DO NOT force the APU into the socket to prevent bending the pins and
damaging the APU!

1.6.1

Installing the APU

To install a APU:
1.

Locate the FM1 socket on the motherboard.

F1A75-V EVO

F1A75-V EVO APU socket FM1
2.

Press the lever sideways to unlock the
socket, then lift it up to a 90°-100° angle.

Socket lever

Ensure that the socket lever is lifted up to a 90°-100° angle; otherwise, the APU will not fit
in completely.

Position the APU above the socket such that the APU
corner with the gold triangle matches the socket corner
with a small triangle.

Carefully insert the APU into the socket until it fits in place.
The APU fits only in one correct orientation.
DO NOT force the APU into the socket to
prevent bending the pins and damaging the
APU!
Small triangle
Gold triangle

ASUS F1A75-V EVO

1-9

When the APU is in place, push down the socket
lever to secure the APU. The lever clicks on the side
tab to indicate that it is locked.

Install a APU heatsink and fan following the
instructions that comes with the heatsink package.
You can also refer to section 1.6.2 Installing
heatsink and fan for instructions.

Connect the CPU fan cable to the CPU_FAN connector on the motherboard.

CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND

CPU_FAN

F1A75-V EVO

F1A75-V EVO CPU fan connector
DO NOT forget to connect the CPU fan connector! Hardware monitoring errors can occur if
you fail to plug this connector.

1-10

Chapter 1: Product introduction

1.6.2

Installing the heatsink and fan
Ensure that you use only AMD-certified heatsink and fan assembly.

To install the CPU heatsink and fan:
1.

Place the heatsink on top of the installed CPU, ensuring that the heatsink fits properly
on the retention module base.
• The retention module base is already installed on the motherboard upon purchase.
• You do not have to remove the retention module base when installing the CPU or
installing other motherboard components.
• If you purchased a separate CPU heatsink and fan assembly, ensure that a Thermal
Interface Material is properly applied to the CPU heatsink or CPU before you install the
heatsink and fan assembly.

CPU Fan

CPU Heatsink

Retention bracket
Retention Module Base
Retention bracket lock

Your boxed CPU heatsink and fan assembly should come with installation instructions for
the CPU, heatsink, and the retention mechanism. If the instructions in this section do not
match the CPU documentation, follow the latter.

Attach one end of the retention bracket to the retention module base.

1
2

ASUS F1A75-V EVO

4
5

1-11

Align the other end of the retention bracket to the retention module base. A clicking
sound denotes that the retention bracket is in place.
Ensure that the fan and heatsink assembly perfectly fits the retention mechanism module
base, otherwise you cannot snap the retention bracket in place.

Push down the retention bracket lock on the retention mechanism to secure the
heatsink and fan to the module base.

When the fan and heatsink assembly is in place, connect the CPU fan cable to the
connector on the motherboard labeled CPU_FAN.
DO NOT forget to connect the CPU fan connector! Hardware monitoring errors can occur if
you fail to plug this connector.

1.7

System memory

1.7.1

Overview

DIMM_B1
DIMM_B2

DIMM_A1
DIMM_A2

This motherboard comes with four Double Data Rate 3 (DDR3) Dual Inline Memory Modules
(DIMM) sockets. A DDR3 module has the same physical dimensions as a DDR2 DIMM but
is notched differently to prevent installation on a DDR2 DIMM socket. DDR3 modules are
developed for better performance with less power consumption. The figure illustrates the
location of the DDR3 DIMM sockets:

Channel
F1A75-V EVO

Sockets

Channel A

DIMM_A1 and DIMM_A2

Channel B

DIMM_B1 and DIMM_B2

F1A75-V EVO 240-pin DDR3 DIMM sockets

1-12

Chapter 1: Product introduction

1.7.2

Memory configurations

You may install 512MB, 1GB, 2GB, and 4GB unbuffered non-ECC DDR3 DIMMs into the
DIMM sockets.
• You may install varying memory sizes in Channel A and Channel B. The system maps
the total size of the lower-sized channel for the dual-channel configuration. Any excess
memory from the higher-sized channel is then mapped for single-channel operation.
• We recommend that you install the memory modules from the blue slots for better
overclocking capability.
• Always install DIMMs with the same CAS latency. For optimum compatibility, we
recommend that you obtain memory modules from the same vendor.
• When overclocking, some AMD CPU models may not support DDR3 1866 MHz or
higher frequency DIMMs.
• Due to the memory address limitation on 32-bit Windows® OS, when you install 4GB
or more memory on the motherboard, the actual usable memory for the OS can be
about 3GB or less. For effective use of memory, we recommend that you do any of the
following:
-

Install a maximum of 3GB system memory if you are using a 32-bit Windows®
OS.
Use a 64-bit Windows® OS if you want to install 4GB or more memory on the
motherboard.

• This motherboard does not support DIMMs made up of 256 megabits (Mb) chips or less.
• The maximum 64GB memory capacity can be supported with 16GB or above DIMMs.
ASUS will update the memory QVL once the DIMMs are available in the market.

• The default memory operation frequency is dependent on its Serial Presence Detect
(SPD), which is the standard way of accessing information from a memory module.
Under the default state, some memory modules for overclocking may operate at a
lower frequency than the vendor-marked value. To operate at the vendor-marked or at a
higher frequency, refer to section 2.4 Ai Tweaker menu for manual memory frequency
adjustment.
• For system stability, use a more efficient memory cooling system to support a full
memory load (4 DIMMs) or overclocking condition.

Visit the ASUS website at www.asus.com for the latest QVL.

ASUS F1A75-V EVO

1-13

1.7.3

Installing a DIMM
Unplug the power supply before adding or removing DIMMs or other system components.
Failure to do so can cause severe damage to both the motherboard and the components.

Press the retaining clips outward to
unlock a DIMM socket.

Align a DIMM on the socket such that
the notch on the DIMM matches the
DIMM slot key on the socket.

DIMM notch

1
DIMM slot key

Unlocked retaining clip

A DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into
a socket in the wrong direction to avoid damaging the DIMM.

Firmly insert the DIMM into the socket
until the retaining clips snap back in place
and the DIMM is properly seated.

Locked Retaining Clip

1.7.4

Removing a DIMM

To remove a DIMM:
1.

Simultaneously press the retaining clips
outward to unlock the DIMM.
2
Support the DIMM lightly with your
fingers when pressing the retaining
clips. The DIMM might get damaged
when it flips out with extra force.

1
DIMM notch

1-14

Remove the DIMM from the socket.

Chapter 1: Product introduction

1.8

Expansion slots

In the future, you may need to install expansion cards. The following sub‑sections describe
the slots and the expansion cards that they support.
Unplug the power cord before adding or removing expansion cards. Failure to do so may
cause you physical injury and damage motherboard components.

1.8.1

Installing an expansion card

To install an expansion card:
1.

Before installing the expansion card, read the documentation that came with it and
make the necessary hardware settings for the card.

Remove the system unit cover (if your motherboard is already installed in a chassis).

Remove the bracket opposite the slot that you intend to use. Keep the screw for later
use.

Align the card connector with the slot and press firmly until the card is completely
seated on the slot.

Secure the card to the chassis with the screw you removed earlier.

Replace the system cover.

1.8.2

Configuring an expansion card

After installing the expansion card, configure it by adjusting the software settings.
1.

Turn on the system and change the necessary BIOS settings, if any. See Chapter 2 for
information on BIOS setup.

Assign an IRQ to the card.

Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that
the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI
groups, making the system unstable and the card inoperable.

1.8.3

PCI slots

1.8.4

PCI Express 2.0 x1 slots

1.8.5

PCI Express 2.0 x16 slots

The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that
comply with PCI specifications.

This motherboard supports PCI Express 2.0 x1 network cards, SCSI cards, and other cards
that comply with the PCI Express 2.0 specifications.
This motherboard has three PCI Express 2.0 x16 slots that support PCI Express 2.0 x16
graphic cards complying with the PCI Express specifications.
VGA configuration
Single VGA/PCIe card
Dual VGA/PCIe card

ASUS F1A75-V EVO

PCI Express operating mode
PCIe x16_1

PCIe x16_2

PCIe x16_3

x16 (Recommended for single VGA card)

N/A

x16

N/A

1-15

• In single VGA card mode, use the PCIe 2.0 x16_1 slot (blue) for a PCI Express x16
graphics card to get better performance.
• We recommend that you provide sufficient power when running CrossFireX™ mode.
See page 1-20 for details.
• Connect a chassis fan to the motherboard connector labeled CHA_FAN1/2 when using
multiple graphics cards for better thermal environment.
• In CrossFireXTM mode, use the PCIe 2.0 x16_1 and PCIe 2.0 x16 _2 slots for PCI
Express x16 graphics cards to get better performance.
• The PCIe x16_3 slot shares bandwidth with PCIe x1_2 slot. Due to the CrossFireXTM
limitation, DO NOT use the PCIe x1_2 slot when you install two CrossFireXTM graphics
cards on both the PCIe x16_1 and PCIe x16_3 slots to set up a CrossFireXTM
configuration.

1.9

Jumpers
Clear RTC RAM (CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can
clear the CMOS memory of date, time, and system setup parameters by erasing
the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in
CMOS, which include system setup information such as system passwords.

CLRTC

F1A75-V EVO

Normal
(Default)

Clear RTC

F1A75-V EVO Clear RTC RAM

To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3
for about 5~10 seconds, then move the cap back to pins 1-2.
3. Plug the power cord and turn ON the computer.
4. Hold down the key during the boot process and enter BIOS setup to reenter
data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default
position. Removing the cap will cause system boot failure!
• If the steps above do not help, remove the onboard battery and move the jumper again
to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.
• You do not need to clear the RTC when the system hangs due to overclocking. For
system failure due to overclocking, use the CPU Parameter Recall (C.P.R) feature. Shut
down and reboot the system so the BIOS can automatically reset parameter settings to
default values.
1-16

Chapter 1: Product introduction

1.10

Connectors

1.10.1

Rear panel ports
3

7 8 9 10

PS/2 Keyboard/Mouse Combo port (purple/green). This port is for a PS/2 keyboard
or PS/2 mouse.

Optical S/PDIF Out port. This port connects an external audio output device via an
optical S/PDIF cable.

HDMI port. This port is for a High-Definition Multimedia Interface (HDMI) connector,
and is HDCP compliant allowing playback of HD DVD, Blu-ray, and other protected
content.

Video Graphics Adapter (VGA) port. This 15-pin port is for a VGA monitor or other
VGA-compatible devices
eSATA 6G port. This port is for an extra SATA6G device.

5.
6.

LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN)
through a network hub.

LAN port LED indications
Activity/Link LED

ACT/LINK SPEED
LED
LED

Speed LED

Status

Description

Status

Description

OFF

No link

OFF

10Mbps connection

ORANGE

Linked

ORANGE

100Mbps connection

BLINKING

Data activity

GREEN

1Gbps connection

LAN port

Center/Subwoofer port (orange). This port connects to the center/subwoofer
speakers

Rear Speaker Out port (black). This port connects to the rear speakers in the
4, 6, and 8-channel audio configurations.

Line In port (light blue). This port connects to the tape, CD, DVD player, or other
audio sources.

10. Line Out port (lime). This port connects to a headphone or a speaker. In the 4, 6 and
8-channel configurations, the function of this port becomes Front Speaker Out.
11.

Microphone port (pink). This port connects to a microphone.

12. Side Speaker Out port (gray). This port connects to the side speakers in the
8-channel audio configuration.
ASUS F1A75-V EVO

1-17

Refer to the audio configuration table below for the function of the audio ports in the 2, 4, 6,
or 8-channel configuration.

Audio 2, 4, 6, or 8-channel configuration
Port

Headset
2-channel

4-channel

6-channel

Light Blue

Line In

Lime

Line Out

Front Speaker Out

8-channel

Pink

Mic In

Orange

–

Center/Subwoofer

Black

–

Rear Speaker Out

Gray

–

Side Speaker Out

13. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are for
USB 2.0/1.1 devices.
14. USB 3.0 ports 1 and 2. These two 9-pin Universal Serial Bus (USB) ports are for USB
3.0 devices.
15. DVI-D port. This port is for any DVI-D compatible device. DVI-D can’t be converted to
output RGB Signal to CRT and isn’t compatible with DVI-I.
16. DisplayPort. This port is for a DisplayPort-compatible devices.
17. USB 3.0 ports 3 and 4. These two 9-pin Universal Serial Bus (USB) ports are for USB
3.0 devices.
• DO NOT connect a keyboard / mouse to any USB 3.0 port when installing Windows®
operating system.
• Due to USB 3.0 controller limitation, USB 3.0 devices can only be used under Windows®
OS environment and after the USB 3.0 driver installation.
• USB 3.0 devices can only be used as data storage only.
• We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster
and better performance for your USB 3.0 devices.
Dual display table
This table indicates whether the dual display you want to use is supported or not.
Dual display output

Supported

DVI + D-Sub

•

HDMI + D-Sub

•

DVI + HDMI

1-18

Not supported

•

DVI + DisplayPort

•

D-Sub + DisplayPort

•

HDMI + DisplayPort

•

Chapter 1: Product introduction

1.10.2
1.

Internal connectors

Power, CPU and chassis fan connectors (3-pin PWR FAN, 4-pin CPU_FAN, and
4-pin CHA_FAN1/2)
Connect the fan cables to the fan connectors on the motherboard, ensuring that the
black wire of each cable matches the ground pin of the connector.

CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND

CPU_FAN

CHA_FAN2
CHA FAN PWM
CHA FAN IN
CHA FAN PWR
GND

PWR_FAN CHA_FAN1

CHA FAN PWM
CHA FAN IN
CHA FAN PWR
GND

Rotation
+12V
GND

F1A75-V EVO

F1A75-V EVO fan connectors
DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside
the system may damage the motherboard components. These are not jumpers! DO NOT
place jumper caps on the fan connectors.

• The CPU_FAN connector supports a CPU fan of maximum 2A (24 W) fan power.
• Only the CPU_FAN and CHA_FAN1/2 connectors support the ASUS Fan Xpert feature.
• If you install two VGA cards, we recommend that you plug the rear chassis fan cable to
the motherboard connector labeled CHA_FAN1/2 for better thermal environment.

ASUS F1A75-V EVO

1-19

ATX power connectors (24-pin EATXPWR, 8-pin EATX12V)
These connectors are for an ATX power supply. The plugs from the power supply are
designed to fit these connectors in only one orientation. Find the proper orientation and
push down firmly until the connectors completely fit.

F1A75-V EVO

GND
GND
GND
GND

+12V DC
+12V DC
+12V DC
+12V DC

EATX12V

EATXPWR

+3 Volts
+12 Volts
+12 Volts
+5V Standby
Power OK
GND
PIN 1
+5 Volts
GND
+5 Volts
GND
+3 Volts
+3 Volts

GND
+5 Volts
+5 Volts
+5 Volts
-5 Volts
GND
GND
GND
PSON#
GND
-12 Volts
+3 Volts

PIN 1

F1A75-V EVO ATX power connectors
• We recommend that you use an ATX 12V Specification 2.0‑compliant power supply unit
(PSU) with a minimum of 300W power rating. This PSU type has 24-pin and 4-pin power
plugs.
• If you intend to use a PSU with 20-pin and 4-pin power plugs, ensure that the 20-pin
power plug can provide at least 15 A on +12 V and that the PSU has a minimum power
rating of 300W. The system may become unstable or may not boot up if the power is
inadequate.
• DO NOT forget to connect the 4-pin / 8-pin ATX +12V power plug. Otherwise, the system
will not boot up.
• We recommend that you use a PSU with higher power output when configuring a
system with more power-consuming devices or when you intend to install additional
devices. The system may become unstable or may not boot up if the power is
inadequate.
• If you are uncertain about the minimum power supply requirement for your system,
refer to the Recommended Power Supply Wattage Calculator at http://support.asus.
com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for details.

1-20

Chapter 1: Product introduction

Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_E1, SATA6G_1~6)
These connectors are for the Serial ATA 6.0 Gb/s signal cables for Serial ATA hard
disk drives and optical disc drives. If you installed Serial ATA hard disk drives, you can
create a RAID 0, RAID 1, RAID 10 or JBOD configuration through the onboard AMD®
A75 FCH controller.
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND

SATA6G_E1

SATA6G_1
GND
RSATA_RXN1
RSATA_RXP1
GND
RSATA_TXN1
RSATA_TXP1
GND

F1A75-V EVO

GND
RSATA_RXN6
RSATA_RXP6
GND
RSATA_TXN6
RSATA_TXP6
GND

SATA6G_4
GND
RSATA_RXN4
RSATA_RXP4
GND
RSATA_TXN4
RSATA_TXP4
GND

GND
RSATA_RXN3
RSATA_RXP3
GND
RSATA_TXN3
RSATA_TXP3
GND

SATA6G_3

SATA6G_6

SATA6G_2
GND
RSATA_RXN2
RSATA_RXP2
GND
RSATA_TXN2
RSATA_TXP2
GND

GND
RSATA_RXN5
RSATA_RXP5
GND
RSATA_TXN5
RSATA_TXP5
GND

SATA6G_5

F1A75-V EVO SATA 6.0Gb/s connectors

• These connectors are set to IDE mode by default. In IDE mode, you can connect Serial
ATA boot/data hard disk drives to these connectors. If you intend to create a Serial ATA
RAID set using these connectors, set the type of the SATA connectors in the BIOS to
[RAID]. See section 2.5.2 SATA Configuration for details.
• You must install Windows® XP Service Pack 3 or later version before using Serial
ATA hard disk drives. The Serial ATA RAID feature is available only if you are using
Windows® XP SP3 or later version.
• When using hot-plug and NCQ, set the type of the SATA connectors in the BIOS to
[AHCI]. See section 2.5.2 SATA Configuration for details.

Serial port connector (10-1 pin COM1)
This connector is for a serial (COM) port. Connect the serial port module cable to this
connector, then install the module to a slot opening at the back of the system chassis.
COM1
PIN 1

F1A75-V EVO

F1A75-V EVO Serial port (COM1) connector
The COM module is purchased separately.
ASUS F1A75-V EVO

1-21

System panel connector (20-8 pin PANEL)
This connector supports several chassis-mounted functions.
+5V
Ground
Ground
Speaker

SPEAKER

PLED-

PLED+

PLED

PANEL

F1A75-V EVO

IDE_LED

PWRSW

Reset
Ground

IDE_LED+
IDE_LED-

PWR
Ground

PIN 1

RESET

* Requires an ATX power supply

F1A75-V EVO System panel connector
•

System power LED (2-pin PLED)
This 2-pin connector is for the system power LED. Connect the chassis power LED
cable to this connector. The system power LED lights up when you turn on the system
power, and blinks when the system is in sleep mode.

•

Hard disk drive activity LED (2-pin IDE_LED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable
to this connector. The IDE LED lights up or flashes when data is read from or written to
the HDD.

•

System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning speaker. The speaker
allows you to hear system beeps and warnings.

•

ATX power button/soft-off button (2-pin PWRSW)
This connector is for the system power button.

•

Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot without
turning off the system power.

1-22

Chapter 1: Product introduction

Digital audio connector (4-1 pin SPDIF_OUT)

+5V

F1A75-V EVO

SPDIFOUT
GND

This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port.

SPDIF_OUT

F1A75-V EVO Digital audio connector
Ensure that the audio device of Sound playback is Realtek High Definition Audio (the
name may be different based on the OS). Go to Start > Control Panel > Sounds and
Audio Devices > Sound Playback to configure the setting.
The S/PDIF module is purchased separately.

Front panel audio connector (10-1 pin AAFP)

AGND
NC
NC

SENSE2_RETUR

GND
PRESENCE#
SENSE1_RETUR

This connector is for a chassis-mounted front panel audio I/O module that supports
either High Definition Audio or AC`97 audio standard. Connect one end of the front
panel audio I/O module cable to this connector.

AAFP

HD-audio-compliant
pin definition

PIN 1

MIC2
MICPWR
Line out_R
NC
Line out_L

PORT1 L
PORT1 R
PORT2 R
SENSE_SEND
PORT2 L

PIN 1

F1A75-V EVO

Legacy AC’97
compliant definition

F1A75-V EVO Front panel audio connector
• We recommend that you connect a high-definition front panel audio module to this
connector to avail of the motherboard high-definition audio capability.
• If you want to connect a high definition front panel audio module to this connector, set
the Front Panel Type item in the BIOS to [HD]. See section 2.5.5 Onboard Devices
Configuration for details.
• The front panel audio I/O module is purchased separately.

ASUS F1A75-V EVO

1-23

USB 2.0 connectors (10-1 pin USB34, USB56, USB78, USB910)
These connectors are for USB 2.0 ports. Connect the USB module cable to any of
these connectors, then install the module to a slot opening at the back of the system
chassis. These USB connectors comply with USB 2.0 specification that supports up to
480Mbps connection speed.

F1A75-V EVO USB2.0 connectors

PIN 1

USB+5V
USB_P14USB_P14+
GND
NC

USB+5V
USB_P12USB_P12+
GND
NC

USB56

PIN 1

USB+5V
USB_P13USB_P13+
GND

PIN 1

USB+5V
USB_P9USB_P9+
GND

USB+5V
USB_P8USB_P8+
GND
NC
PIN 1

USB+5V
USB_P7USB_P7+
GND

F1A75-V EVO

USB34

USB+5V
USB_P11USB_P11+
GND

USB910
USB+5V
USB_P10USB_P10+
GND
NC

USB78

Never connect a 1394 cable to the USB connectors. Doing so will damage the
motherboard!

The USB 2.0 module is purchased separately.

USB 3.0 connector (20-1 pin USB3_56)
This connector is for the additional USB 3.0 ports. Connect the USB 3.0 bracket cable
to this connector, then install the USB 3.0 bracket to the rear side of the chassis. If your
chassis support customized front panel installation, with ASUS USB 3.0 header, you
can have a front panel USB 3.0 solution.
USB3_56

F1A75-V EVO

F1A75-V EVO USB3.0 Front panel connector
The USB 3.0 module is purchased separately.

1-24

Chapter 1: Product introduction

1.11

Onboard switch

Onboard switches allow you to fine-tune performance when working on a bare or open-case
system. This is ideal for overclockers and gamers who continually change settings to
enhance system performance.
1.

MemOK! switch
Installing DIMMs that are incompatible with the motherboard may cause system
boot failure, and the DRAM_LED near the MemOK! switch lights continuously. Press
and hold the MemOK! switch until the DRAM_LED starts blinking to begin automatic
memory compatibility tuning for successful boot.

F1A75-V EVO

F1A75-V EVO MemOK! switch
• Refer to section 1.12 Onboard LEDs for the exact location of the DRAM_LED.
• The DRAM_LED also lights when the DIMM is not properly installed. Turn off the system
and reinstall the DIMM before using the MemOK! function.
• The MemOK! switch does not function under Windows® OS environment.
• During the tuning process, the system loads and tests failsafe memory settings. It takes
about 30 seconds for the system to test one set of failsafe settings. If the test fails,
the system reboots and test the next set of failsafe settings. The blinking speed of the
DRAM_LED increases, indicating different test processes.
• Due to memory tuning requirement, the system automatically reboots when each timing
set is tested. If the installed DIMMs still fail to boot after the whole tuning process, the
DRAM_LED lights continuously. Replace the DIMMs with ones recommended in the
Memory QVL (Qualified Vendors Lists) in this user manual or on the ASUS website at
www.asus.com.
• If you turn off the computer and replace DIMMs during the tuning process, the system
continues memory tuning after turning on the computer. To stop memory tuning, turn off
the computer and unplug the power cord for about 5–10 seconds.
• If your system fail to boot due to BIOS overclocking, press the MemOK! switch to boot
and load BIOS default settings. A message will appear during POST reminding you that
the BIOS has been restored to its default settings.
• We recommend that you download and update to the latest BIOS version from the
ASUS website at www.asus.com after using the MemOK! function.

ASUS F1A75-V EVO

1-25

TPU switch
This switch allows you to enable or disable the TPU function.
TPU

F1A75-V EVO

F1A75-V EVO TPU switch
• The TPU LED (ELED730) near the TPU switch lights when the switch setting is turned to
Enable.
• If you clear the CMOS or load the BIOS setup defaults, the related overclocking items in
the BIOS menu follow the current setting of the TPU switch.
• If you change the switch setting to Enable under the OS environment, the TPU function
will be activated after the next system bootup.
• You may use the TurboV and Auto Tuning features in the TurboV EVO application, adjust
the BIOS settings, or enable the TPU function at the same time. However, the system will
use the last setting you have made.

EPU switch
This switch allows you to enable or disable the EPU function.
EPU

F1A75-V EVO

F1A75-V EVO EPU switch
• The EPU LED (ELED740) near the TPU switch lights when the switch setting is turned to
Enable.
• If you change the switch setting to Enable under the OS environment, the EPU function
will be activated after the next system bootup.
• You may change the EPU settings in the EPU application, change the BIOS settings, and
enable the EPU function at the same time. However, the system will use the last setting
you have made.

1-26

Chapter 1: Product introduction

1.12
1.

Onboard LEDs

Standby Power LED
The motherboard comes with a standby power LED that lights up to indicate that the
system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should
shut down the system and unplug the power cable before removing or plugging in any
motherboard component. The illustration below shows the location of the onboard LED.

SB_PWR
F1A75-V EVO

ON
Standby Power

OFF
Powered Off

F1A75-V EVO Onboard LED
2.

DRAM LED
DRAM LED checks the DRAM in sequence during motherboard booting process. If an
error is found , the LED next to the error device will continue lighting until the problem
is solved. This user-friendly design provides an intuitional way to locate the root
problem within a second.

DRAM LED

F1A75-V EVO

F1A75-V EVO DRAM LED

TPU LED
The TPU LED lights when the TPU switch is turned to Enable.
ELED 730

F1A75-V EVO

F1A75-V EVO TPU LED

ASUS F1A75-V EVO

1-27

EPU LED
The EPU LED lights when the EPU switch is turned to Enable.
ELED740

F1A75-V EVO

F1A75-V EVO EPU LED

1-28

Chapter 1: Product introduction

1.13

Software support

1.13.1

Installing an operating system

This motherboard supports Windows® XP / Vista / 7 Operating Systems (OS). Always install
the latest OS version and corresponding updates to maximize the features of your hardware.
• Motherboard settings and hardware options vary. Refer to your OS documentation for
detailed information.
• Ensure that you install Windows® XP Service Pack 3 or later versions / Windows® Vista
Service Pack 1 or later versions before installing the drivers for better compatibility and
system stability.

1.13.2

Support DVD information

The Support DVD that comes with the motherboard package contains the drivers, software
applications, and utilities that you can install to avail all motherboard features.
The contents of the Support DVD are subject to change at any time without notice. Visit the
ASUS website at www.asus.com for updates.

To run the Support DVD
Place the Support DVD into the optical drive. If Autorun is enabled in your computer, the DVD
automatically displays the Specials screen. Click Drivers, Utilities, Make Disk, Manual, and
Contact tabs to display their respective menus.
The following screen is for reference only.

Click an icon to
display Support DVD/
motherboard information

Click an item to install
If Autorun is NOT enabled on your computer, browse the contents of the Support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the DVD.

ASUS F1A75-V EVO

1-29

1-30

Chapter 1: Product introduction

Chapter 2
BIOS information
2.1

Managing and updating your BIOS
Save a copy of the original motherboard BIOS file to a USB flash disk in case you need to
restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update
utility.

2.1.1

ASUS Update utility

The ASUS Update is a utility that allows you to manage, save, and update the motherboard
BIOS in Windows® environment.
• ASUS Update requires an Internet connection either through a network or an Internet
Service Provider (ISP).
• This utility is available in the support DVD that comes with the motherboard package.

Installing ASUS Update
To install ASUS Update:
1.

Place the support DVD in the optical drive. The Drivers menu appears.

Click the Utilities tab, then click AI Suite II.

Follow the onscreen instructions to complete the installation.
Quit all Windows® applications before you update the BIOS using this utility.

Updating the BIOS
To update the BIOS:
1.

From the Windows® desktop, click Start > Programs > ASUS > AI Suite II > AI Suite
II X.XX.XX to launch the AI Suite II utility. The AI Suite II Quick Bar appears.

Click Update button from the Quick Bar, and then click ASUS Update from the popup
menu. The ASUS Update main screen appears. From the list, select either of the
following methods:
Updating from the Internet

Select Update BIOS from the Internet, then click Next.

Select the ASUS FTP site nearest you to avoid network traffic, then click Next.

From the FTP site, select the BIOS version that you wish to download then click
Next.

Chapter 2: BIOS information

2-1

The ASUS Update utility is capable of updating itself through the Internet. Always update
the utility to avail all its features.

Updating from a BIOS file

Select Update BIOS from file, then click Next.

Locate the BIOS file from the Open window, then click Open.

Follow the onscreen instructions to complete the updating process.

2.1.2

ASUS EZ Flash 2

The ASUS EZ Flash 2 feature allows you to update the BIOS without using an OS‑based
utility.
Before you start using this utility, download the latest BIOS file from the ASUS website at
www.asus.com.

To update the BIOS using EZ Flash 2:
1.

Insert the USB flash disk that contains the latest BIOS file to the USB port.

Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select
ASUS EZ Flash Utility and press to enable it.
Exit

ASUS EZ Flash 2 Utility V01.02

Flash Info
MODEL: F1A75-V EVO

VER: 0401

DATE: 06/08/2011

File Path: fs0:\
Drive

Folder Info

fs0:\

06/08/11

03:19p

4194304

F1A75VE.ROM

File Info
MODEL: F1A75-V EVO

VER: 0401

DATE: 06/08/11

Help Info

[Enter] Select or Load

2-2

[Tab] Switch

[Up/Down/PageUp/PageDown/Home/End] Move

[Esc] Exit

[F2] Backup

ASUS F1A75-V EVO

Press to switch to the Drive field.

Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS,
and then press .

Press to switch to the Folder Info field.

Press the Up/Down arrow keys to find the BIOS file, and then press to perform
the BIOS update process. Reboot the system when the update process is done.
• This function supports USB flash disks with FAT 32/16 format and single partition only.
• DO NOT shut down or reset the system while updating the BIOS to prevent system boot
failure!

2.1.3

ASUS CrashFree BIOS 3 utility

The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file
when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS
file using the motherboard support DVD or a USB flash drive that contains the updated BIOS
file.
• Before using this utility, rename the BIOS file in the removable device into
F1A75VE.ROM.
• The BIOS file in the support DVD may not be the latest version. Download the latest
BIOS file from the ASUS website at www.asus.com.

Recovering the BIOS
To recover the BIOS:
1.

Turn on the system.

Insert the support DVD to the optical drive or the USB flash drive that contains the
BIOS file to the USB port.

The utility automatically checks the devices for the BIOS file. When found, the utility
reads the BIOS file and enters ASUS EZ Flash 2 utility automatically.

The system requires you to enter BIOS Setup to recover BIOS setting. To ensure
system compatibility and stability, we recommend that you press to load default
BIOS values.
DO NOT shut down or reset the system while updating the BIOS! Doing so can cause
system boot failure!

Chapter 2: BIOS information

2-3

2.1.4

ASUS BIOS Updater

The ASUS BIOS Updater allows you to update BIOS in DOS environment. This utility also
allows you to copy the current BIOS file that you can use as a backup when the BIOS fails or
gets corrupted during the updating process.
The succeeding utility screens are for reference only. The actual utility screen displays may
not be same as shown.

Before updating BIOS
1.

Prepare the motherboard support DVD and a USB flash drive in FAT32/16 format and
single partition.

Download the latest BIOS file and BIOS Updater from the ASUS website at
http://support.asus.com and save them on the USB flash drive.
NTFS is not supported under DOS environment. Do not save the BIOS file and BIOS
Updater to a hard disk drive or USB flash drive in NTFS format.

Turn off the computer and disconnect all SATA hard disk drives (optional).

Booting the system in DOS environment
1.

Insert the USB flash drive with the latest BIOS file and BIOS Updater to the USB port.

Boot your computer. When the ASUS Logo appears, press to show the BIOS
Boot Device Select Menu. Insert the support DVD into the optical drive and select the
optical drive as the boot device.
Please select boot device:

SATA: XXXXXXXXXXXXXXXX
USB XXXXXXXXXXXXXXXXX
UEFI: XXXXXXXXXXXXXXXX
Enter Setup
↑ and ↓ to move selection
ENTER to select boot device
ESC to boot using defaults

When the Make Disk menu appears, select the FreeDOS command prompt item by
pressing the item number.

At the FreeDOS prompt, type d: and press to switch the disk from
Drive C (optical drive) to Drive D (USB flash drive).
Welcome to FreeDOS (http://www.freedos.org)!
C:\>d:
D:\>

2-4

ASUS F1A75-V EVO

Backing up the current BIOS
To backup the current BIOS file using the BIOS Updater
Ensure that the USB flash drive is not write-protected and has enough free space to save
the file.

At the FreeDOS prompt, type bupdater /o[filename] and press .
D:\>bupdater /oOLDBIOS1.rom

Filename Extension

The [filename] is any user-assigned filename with no more than eight alphanumeric
characters for the filename and three alphanumeric characters for the extension.

The BIOS Updater backup screen appears indicating the BIOS backup process. When
BIOS backup is done, press any key to return to the DOS prompt.
ASUSTek BIOS Updater for DOS V1.07
Current ROM
BOARD: F1A75-V EVO
VER: 0401
DATE: 06/08/2011

Update ROM
BOARD: Unknown
VER: Unknown
DATE: Unknown

PATH: A:\
BIOS backup is done! Press any key to continue.

Note
Saving BIOS:

Chapter 2: BIOS information

2-5

Updating the BIOS file
To update the BIOS file using BIOS Updater
1.

At the FreeDOS prompt, type bupdater /pc /g and press .
D:\>bupdater /pc /g

The BIOS Updater screen appears as below.
ASUSTek BIOS Updater for DOS V1.07
Current ROM
BOARD: F1A75-V EVO
VER: 0401
DATE: 06/08/2011

Update ROM
BOARD: Unknown
VER: Unknown
DATE: Unknown

PATH: A:\
F1A75VE.ROM

Note

[Enter] Select or Load
[Up/Down/Home/End] Move

4194304 2011-06-08 17:30:48

[Tab] Switch
[B] Backup

[V] Drive Info
[Esc] Exit

Press to switch between screen fields and use the keys
to select the BIOS file and press . BIOS Updater checks the selected BIOS file
and prompts you to confirm BIOS update.

Are you sure to update BIOS?
Yes

Select Yes and press . When BIOS update is done, press to exit BIOS
Updater. Restart your computer.
DO NOT shut down or reset the system while updating the BIOS to prevent system boot
failure!
• For BIOS Updater version 1.04 or later, the utility automatically exits to the DOS prompt
after updating BIOS.
• Ensure to load the BIOS default settings to ensure system compatibility and stability.
Select the Load Optimized Defaults item under the Exit menu. Refer to section 2.9
Exit menu for details.
• Ensure to connect all SATA hard disk drives after updating the BIOS file if you have
disconnected them.

2-6

ASUS F1A75-V EVO

2.2

BIOS setup program

Use the BIOS Setup program to update the BIOS or configure its parameters. The BIOS
screens include navigation keys and brief online help to guide you in using the BIOS Setup
program.

Entering BIOS Setup at startup
To enter BIOS Setup at startup:
• Press during the Power-On Self Test (POST). If you do not press ,
POST continues with its routines.

Entering BIOS Setup after POST
To enter BIOS Setup after POST:
• Press ++ simultaneously.
•

Press the reset button on the system chassis.

•

Press the power button to turn the system off then back on. Do this option only if you
failed to enter BIOS Setup using the first two options.
Using the power button, reset button, or the ++ keys to force reset from
a running operating system can cause damage to your data or system. We recommend to
always shut down the system properly from the operating system.

• The BIOS setup screens shown in this section are for reference purposes only, and may
not exactly match what you see on your screen.
• Ensure that a USB mouse is connected to your motherboard if you want to use the
mouse to control the BIOS setup program.
• The default BIOS settings for this motherboard apply for most conditions to ensure
optimum performance. If the system becomes unstable after changing any BIOS
settings, load the default settings to ensure system compatibility and stability. Select the
Load Optimized Defaults item under the Exit Menu. See section 2.9 Exit Menu.
• If the system fails to boot after changing any BIOS setting, try to clear the CMOS and
reset the motherboard to the default value. Refer to section 1.9 Jumpers on how to
erase the RTC RAM.
• The BIOS setup program does not support the bluetooth devices.

Chapter 2: BIOS information

2-7

BIOS menu screen

The BIOS setup program can be used under two modes: EZ Mode and Advanced Mode.
You can change modes from the Exit menu or from the Exit/Advanced Mode button in the EZ
Mode/Advanced Mode screen.

EZ Mode
By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ
Mode provides you an overview of the basic system information, and allows you to select
the display language, system performance mode and boot device priority. To access the
Advanced Mode, click Exit/Advanced Mode, then select Advanced Mode.
The default screen for entering the BIOS setup program can be changed. Refer to the
Setup Mode item in section 2.7 Boot menu for details.
Clicks to display all fan
speeds if available

Selects the display language of
the BIOS setup program
Displays the CPU/motherboard temperature,
CPU/5V/3.3V/12V voltage output,
CPU/chassis/power fan speed

Exits the BIOS setup program without saving
the changes, saves the changes and resets
the system, or enters the Advanced Mode

EFI BIOS Utility - EZ Mode

Exit/Advanced Mode

F1A75-V EVO

Friday [10/08/2010]

English

BIOS Version : 0401

Build Date : 06/08/2011

CPU Type : AMD Engineering Sample

Speed : 2400 MHz

Total Memory : 1024 MB (DDR3 1066MHz)

Temperature

Voltage

CPU

+113.0ºF/+45.0ºC

CPU

1.248V

+75.2ºF/+40.0ºC

3.3V

3.344V

12V

Fan Speed

5.160V

CPU_FAN

3325RPM

PWR_FAN

N/A

12.248V

CHA_FAN

3325RPM

CHA_FAN2

N/A

Q-Fan Control
Quiet

Performance

Energy Saving

Normal

Boot Priority

Use the mouse to drag or keyboard to navigate to decide the boot priority.
Boot Menu(F8)

Selects the boot device priority

Power Saving mode

Displays the system properties of the
selected mode on the right hand side

Normal mode

Default(F5)

Loads optimized default
ASUS Optimal mode

Selects the boot device priority

• The boot device options vary depending on the devices you installed to the system.
• The Boot Menu(F8) button is available only when the boot device is installed to the
system.

2-8

ASUS F1A75-V EVO

Advanced Mode
The Advanced Mode provides advanced options for experienced end-users to configure
the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the
following sections for the detailed configurations.
To access the EZ Mode, click Exit, then select ASUS EZ Mode.

Back button

Menu items

Menu bar

Configuration fields

General help

EFI BIOS Utility - Advanced Mode

Ai Tweaker

Main
Back

Exit

Advanced

Monitor

Boot

Tool

Advanced\ Onboard Devices Configuration >

HD Audio Controller

Enabled/Disabled Asmedia USB 3.0

Enabled

Front Panel Type

SPDIF Out Type

SPDIF

ASM1061 Storage Controller

AHCI Mode

ASM1061 Storage OPROM

Enabled

Asmedia USB 3.0 Controller
Realtek LAN Controller
Disabled
Enabled
Realtek PXE OPROM

Enabled

Asmedia USB 3.0 Controller

Enabled

Asmedia USB 3.0 Battery Charging Support

Disabled

Disabled
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit

> Serial Port Configuration

Submenu item

Pop-up window

Scroll bar

Navigation keys

Menu bar
The menu bar on top of the screen has the following main items:
Main

For changing the basic system configuration

Ai Tweaker

For changing the overclocking settings

Advanced

For changing the advanced system settings

Monitor

For displaying the system temperature, power status, and changing the fan settings

Boot

For changing the system boot configuration

Tool

For configuring options for special functions

Exit

For selecting the exit options and loading default settings

Chapter 2: BIOS information

2-9

Menu items
The highlighted item on the menu bar displays the specific items for that menu. For example,
selecting Main shows the Main menu items.
The other items (Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have
their respective menu items.

Back button
This button appears when entering a submenu. Press or use the USB mouse to click
this button to return to the previous menu screen.

Submenu items
A greater than sign (>) before each item on any menu screen means that the item has a
submenu. To display the submenu, select the item and press or double-click the
item.

Pop-up window
Select a menu item and press to display a pop-up window with the configuration
options for that item.

Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not fit on
the screen. Press the Up/Down arrow keys or / keys to display the
other items on the screen.

Navigation keys
At the bottom right corner of the menu screen are the navigation keys for the BIOS setup
program. Use the navigation keys to select items in the menu and change the settings.

General help
At the top right corner of the menu screen is a brief description of the selected item.

Configuration fields
These fields show the values for the menu items. If an item is user-configurable, you can
change the value of the field opposite the item. You cannot select an item that is not
user-configurable.
A configurable field is highlighted when selected. To change the value of a field, select it and
press or click on it to display a list of options.

2-10

ASUS F1A75-V EVO

2.3

Main menu

The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup
program. The Main menu provides you an overview of the basic system information, and
allows you to set the system date, time, language, and security settings.
EFI BIOS Utility - Advanced Mode

Main

Ai Tweaker

Exit

Advanced

Monitor

BIOS Information
BIOS Version
Build Date

0401 x64
06/08/2011

CPU Information
AMD Engineering Sample
Speed

2400 MHz

Memory Information
Total Memory
Speed

1024 MB (DDR3)
1333 MHz

System Language
System Date
System Time
Access Level

Boot

Tool

Choose the system default language

English

[Thu 01/20/2011]
[16:46:15]
Administrator

> Security

2.3.1

System Language [English]

2.3.2

System Date [Day xx/xx/xxxx]

2.3.3

System Time [xx:xx:xx]

2.3.4

Security

→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.

Allows you to choose the BIOS language version from the options. Configuration options:
[English]
Allows you to set the system date.
Allows you to set the system time.

The Security menu items allow you to change the system security settings.
• If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC)
RAM to clear the BIOS password. See section 1.9 Jumpers for information on how to
erase the RTC RAM.
• The Administrator or User Password items on top of the screen show the default Not
Installed. After you set a password, these items show Installed.

Chapter 2: BIOS information

2-11

Administrator Password
If you have set an administrator password, we recommend that you enter the administrator
password for accessing the system. Otherwise, you might be able to see or change only
selected fields in the BIOS setup program.
To set an administrator password:
1.

Select the Administrator Password item and press .

From the Create New Password box, key in a password, then press .

Confirm the password when prompted.

To change an administrator password:
1.

Select the Administrator Password item and press .

From the Enter Current Password box, key in the current password, then press
.

From the Create New Password box, key in a new password, then press .

Confirm the password when prompted.

To clear the administrator password, follow the same steps as in changing an administrator
password, but press when prompted to create/confirm the password. After you clear
the password, the Administrator Password item on top of the screen shows Not Installed.

User Password
If you have set a user password, you must enter the user password for accessing the system.
The User Password item on top of the screen shows the default Not Installed. After you set
a password, this item shows Installed.
To set a user password:
1.

Select the User Password item and press .

From the Create New Password box, key in a password, then press .

Confirm the password when prompted.

To change a user password:
1.

Select the User Password item and press .

From the Enter Current Password box, key in the current password, then press
.

From the Create New Password box, key in a new password, then press .

Confirm the password when prompted.

To clear the user password, follow the same steps as in changing a user password, but press
when prompted to create/confirm the password. After you clear the password, the
User Password item on top of the screen shows Not Installed.

2-12

ASUS F1A75-V EVO

2.4

Ai Tweaker menu

The Ai Tweaker menu items allow you to configure overclocking-related items.
Be cautious when changing the settings of the Ai Tweaker menu items. Incorrect field
values can cause the system to malfunction.

The configuration options for this section vary depending on the CPU and DIMM model you
installed on the motherboard.
EFI BIOS Utility - Advanced Mode

Main

Ai Tweaker

Exit

Advanced

Monitor

Target CPU Speed: XXXXMHz

Boot

Tool

[X.M.P.] When XMP is enabled BCLK
frequency, CPU ratio and memory
parameters will be auto optimized.

Target DRAM Speed: XXXXMHz
Ai Overclock Tuner

Auto

Memory Frequency

Auto

APU Multiplier

Auto

EPU Power Saving Mode

Disabled

> OC Tuner
> DRAM Timing Control
CPU Voltage

Offset Mode

CPU Offset Mode Sign
CPU Offset Voltage

1.375V

Auto

VDDNB Offset Mode Sign
VDDNB Offset Voltage

1.150V

Auto

DRAM Voltage

1.500V

Auto

SB 1.1V Voltage

1.100V

Auto

→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
F12: Print Screen

Scroll down to display the following items:
1.1Vsb Voltage

1.100V

Auto

APU1.2V Voltage

1.200V

Auto

VDDA Voltage

2.500V

Auto

Digi + VRM
CPU Load Line Calibration

Auto

CPU/NB Load Line Calibration

Auto

CPU Current Capability

100%

CPU/NB Current Capability

100%

CPU Power Phase Control

Standard

CPU Voltage Frequency

Auto

VRM Spread Spectrum

Disabled

CPU Power Duty Control

T.Probe

APU Spread Spectrum

Auto

Chapter 2: BIOS information

2-13

Target CPU Speed : xxxxMHz
Displays the current CPU speed.

Target DRAM Speed : xxxxMHz
Displays the current DRAM speed.

2.4.1

Ai Overclock Tuner [Auto]

Allows you to select the CPU overclocking options to achieve the desired CPU internal
frequency. Select any of these preset overclocking configuration options:
[Auto] Loads the optimal settings for the system.
[Manual]
Allows you to individually set overclocking parameters.
[D.O.C.P.]
Allows you to select a DRAM O.C. profile, and the related parameters will
be adjusted automatically.

APU Frequency [XXX]
This item appears only when you set the Ai Overclock Tuner item to [Manual]. Use the <+>
and <-> keys to adjust the value. You can also key in the desired value using the numeric
keypad. The values range from 90.0MHz to 300.0MHz.

DRAM O.C. Profile [DDR3-1600MHz 9-9-9-24 1.65V]
This item appears only when you set the Ai Overclock Tuner item to [D.O.C.P.]. and allows
you to select a DRAM O.C. profile, which applies different settings to DRAM frequency,
DRAM timing and DRAM voltage. Configuration options: [DDR3-1600MHz 9-9-9-24 1.65V]
[DDR3-1800MHz 9-9-9-24 1.65V] [DDR3-1866MHz 9-9-9-24 1.65V] [DDR3-2000MHz 9-99-24 1.65V] [DDR3-2133MHz 9-9-9-24 1.65V] [DDR3-2200MHz 9-9-9-24 1.65V] [DDR32400MHz 9-9-9-24 1.65V]

2.4.2

Memory Frequency [Auto]

Allows you to set the memory operating frequency. Configuration options: [Auto]
[DDR3-800MHz] [DDR3-1066MHz] [DDR3-1333MHz] [DDR3-1600MHz] [DDR3-1866MHz]
Selecting a very high memory frequency may cause the system to become unstable! If this
happens, revert to the default setting.

2.4.3

APU Multiplier [Auto]

2.4.4

EPU Power Saving Mode [Disabled]

Allows you to set the multiplier between the CPU Core Clock and the FSB Frequency. Use
the <+> and <-> keys to adjust the ratio. The valid value ranges vary according to your CPU
model.
Allows you to enable or disable the EPU power saving function.
Configuration options: [Disabled] [Enabled]
EPU Setting [Auto]

This item appears only when The EPU Power Saving Mode is set to [Enabled] and
allows you to set power saving mode. Configuration options: [Auto] [Light Power
Saving Mode] [Medium Power Saving Mode] [Max Power Saving Mode]

2-14

ASUS F1A75-V EVO

2.4.5

OC Tuner

2.4.6

DRAM Timing Control

OC Tuner automatically overclocks the frequency and voltage of CPU and DRAM for
enhancing the system performance. Press and select OK to start automatic
overclocking.
The sub-items in this menu allow you to set the DRAM timing control features. Use the <+>
and <-> keys to adjust the value. To restore the default setting, type [auto] using the keyboard
and press .
Changing the values in this menu may cause the system to become unstable! If this
happens, revert to the default settings.

2.4.7

CPU Voltage [Offset Mode]

[Offset Mode] To offset the voltage by a positive or negative value.
[Manual Mode] To set the voltage manually.

CPU Offset Mode Sign [+]
This item appears only when you set the CPU Voltage item to [Offset Mode].
[+]
To offset the voltage by a positive value.
[–]
To offset the voltage by a negative value.
CPU Offset Voltage [Auto]

Allows you to set the CPU Offset voltage. The values range from 0.00625V to 0.500V
with a 0.00625V interval.
Refer to the CPU documentation before setting the CPU voltage. Setting a high voltage
may damage the CPU permanently, and setting a low voltage may make the system
unstable.

VDDNB Offset Mode Sign [+]
This item appears only when you set the CPU Voltage item to [Offset Mode].
[+]
To offset the voltage by a positive value.
[–]
To offset the voltage by a negative value.
VDDNB Offset Voltage [Auto]

Allows you to set the VDDNB Offset voltage. The values range from 0.00625V to
0.500V with a 0.00625V interval.

CPU Manual Voltage [Auto]
This item appears only when you set the CPU Voltage item to [Manual Mode] and allows you
to manually set the CPU voltage. The values range from 0.800V to 1.550V with a 0.0125V
interval.

VDDNB Manual Voltage [Auto]
This item appears only when you set the CPU Voltage item to [Manual Mode] and allows you
to manually set the VDDNB voltage. The values range from 0.800V to 1.550V with a 0.0125V
interval.

Chapter 2: BIOS information

2-15

2.4.8

DRAM Voltage [Auto]

2.4.9

SB 1.1V Voltage [Auto]

2.4.10

1.1Vsb Voltage [Auto]

2.4.11

APU1.2V Voltage [Auto]

2.4.12

VDDA Voltage [Auto]

Allows you to set the DRAM voltage. The values range from 1.35V to 2.30V with a 0.01V
interval.
Allows you to set the Southbridge 1.1V voltage. The values range from 1.1V to 1.4V with a
0.01V interval.
Allows you to set the 1.1Vsb voltage. The values range from 1.1000V to 1.2000V with a 0.1V
interval.
Allows you to set the APU (Accelerated Processor Unit) 1.2V voltage. The values range from
1.2000V to 1.8000V with a 0.01V interval.
Allows you to set the VDDA voltage. The values range from 2.5000V to 2.8000V with a 0.1V
interval.
• The values of the CPU Offset Voltage, VDDNB Offset Voltage, DRAM Voltage, SB
1.1V Voltage, 1.1Vsb Voltage, APU1.2V Voltage, and VDDA Voltage items are labeled
in different color, indicating the risk levels of high voltage settings.
• The system may need better cooling system to work stably under high voltage settings.

2.4.13

DIGI + VRM

CPU Load Line Calibration [Auto]
CPU Load-line Calibration is defined by AMD VRM specifications and affects CPU voltage.
The CPU working voltage will decrease proportionally to CPU loading. Higher load-line
calibration would get higher voltage and better overclocking performance, but increase the
CPU and VRM thermal. This item allows you to adjust the voltage range from the following
percentages to boost the system performance: 0% (Regular), 25% (Medium), 50% (High),
75% (Ultra High) and 100% (Extreme). Configuration options: [Auto] [Regular] [Medium]
[High] [Ultra High] [Extreme]
The actual performance boost may vary depending on your CPU specifiation.

CPU/NB Load Line Calibration [Auto]
Allows you to select the CPU/NB Load-Line Calibration mode. Configuration options: [Auto]
[Regular] [High] [Extreme]

CPU Current Capability [100%]
This item provides wider total power range for overclocking. A higher value brings a
wider total power range and extends the overclocking frequency range simultaneously.
Configuration options: [100%] [110%] [120%] [130%] [140%]

2-16

ASUS F1A75-V EVO

CPU/NB Current Capability [100%]
This item provides wider total power range for overclocking. A higher value brings a
wider total power range and extends the overclocking frequency range simultaneously.
Configuration options: [100%] [110%] [120%] [130%]

CPU Power Phase Control [Standard]
Phase number is the number of working VRM phase. Increasing phase number under heavy
system loading to get more transient and better thermal performance. Reducing phase
number under light system loading to increase VRM efficiency.
[Standard]
Proceeds phase control depending on the CPU loading.
[Optimized]
Loads the ASUS optimized phase tuning profile.
[Extreme]
Proceeds the full phase mode.
[Manual Adjustment] Allows manual adjustment.

CPU Voltage Frequency [Auto]
Switching frequency will affect the VRM transient response and component thermal. Setting a
higher frequency gets faster transient response.
[Auto]
Allows you to enable or disable the Spread Spectrum item.
[Manual]
Allows you to manually set the frequency with a 10k Hz interval.

VRM Spread Spectrum [Disabled]
This item appears only when you set the CPU Voltage Frequency item to [Auto] and allows
you to enable the spread spectrum to enhance system stability.

VRM Fixed Frequency Mode [xxx]
This item appears only when you set the CPU Voltage Frequency item to [Manual] and allows
you to set a fixed VRM frequency. Use the <+> and <-> keys to adjust the value. The values
range from 200k Hz to 400k Hz with a 10k Hz interval.

CPU Power Duty Control [T.Probe]
[T.Probe]
[Extreme]

Maintains the VRM thermal balance.
Maintains the VRM current balance.
Do not remove the thermal module while changing the DIGI+VRM related parameters. The
thermal conditions should be monitored.

2.4.14

APU Spread Spectrum [Auto]

[Auto] Automatic configuration.
[Disabled]
Enhances the PCIE overclocking ability.
[Enabled]
Sets to [Enabled] for EMI control.

Chapter 2: BIOS information

2-17

2.5

Advanced menu

The Advanced menu items allow you to change the settings for the CPU and other system
devices.
Be cautious when changing the settings of the Advanced menu items. Incorrect field values
can cause the system to malfunction.
EFI BIOS Utility - Advanced Mode

Ai Tweaker

Main

Advanced

> CPU Configuration

Exit

Monitor

Boot

Tool

CPU Configuration Parameters

> SATA Configuration
> USB Configuration
> NB Configuration
> Onboard Devices Configuration
> APM

2.5.1

CPU Configuration

The items in this menu show the CPU-related information that the BIOS automatically
detects.
The items shown in submenu may be different due to the CPU you installed.

Limit CPUID Maximum [Disabled]
[Enabled] Allows legacy operating systems to boot even without support for CPUs
with extended CPUID functions.
[Disabled]
Disables this function.

C6 Mode [Auto]
Enables or disables C6 mode. Configuration options: [Auto] [Enabled] [Disabled]

CPB Mode [Auto]
Disables the CPB (Core Performance Boost) mode or set it to [Auto] for automatic
configuration. Configuration options: [Disabled] [Auto]

AMD PowerNow function [Enabled]
Enables or disables the AMD PowerNow function. Configuration options: [Enabled] [Disabled]

SVM [Enabled]
Enables or disables CPU virtualization. Configuration options: [Disabled] [Enabled]

2-18

ASUS F1A75-V EVO

2.5.2

SATA Configuration

While entering Setup, the BIOS automatically detects the presence of SATA devices. The
SATA Port items show Not Present if no SATA device is installed to the corresponding SATA
port.

OnChip SATA Channel [Enabled]
Enables or disables onboard channel SATA port. Configuration options: [Disabled] [Enabled]
The following three items appear only when you set the OnChip SATA Channel to
[Enabled].

OnChip SATA Type [IDE]
Allows you to set the SATA configuration.
[IDE] Set to [IDE] when you want to use the Serial ATA hard disk drives as
Parallel ATA physical storage devices.
[RAID]
Set to [RAID] when you want to create a RAID configuration from the SATA
hard disk drives.
[AHCI] Set to [AHCI] when you want the SATA hard disk drives to use the AHCI
(Advanced Host Controller Interface). The AHCI allows the onboard storage
driver to enable advanced Serial ATA features that increases storage
performance on random workloads by allowing the drive to internally
optimize the order of commands.
SATA Port 5 - Port 6 [AHCI or RAID]

This item only appears when the previous item is set to [RAID] or [AHCI]. If Port 5-6
are configured as [AHCI or RAID], the ports can only be used under OS with driver
installed. Set to [IDE] instead of [AHCI or RAID] to access devices on Port 5-6 before
entering OS. Configuration options: [AHCI or RAID] [IDE]

OnChip SATA MAX Speed [SATA 6.0Gb/s]
Sets the maximum onboard SATA port speed. Configuration options: [SATA 3.0Gb/s] [SATA
6.0Gb/s]

S.M.A.R.T. Status Check [Enabled]
S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When
read/write of your hard disk errors occur, this feature allows the hard disk to report warning
messages during the POST. Configuration options: [Enabled] [Disabled]

2.5.3

USB Configuration

The items in this menu allow you to change the USB-related features.
The USB Devices item shows the auto-detected values. If no USB device is detected, the
item shows None.

Legacy USB Support [Enabled]
[Enabled]
[Disabled]
[Auto]

Enables the support for USB devices on legacy operating systems (OS).
The USB devices can be used only for the BIOS setup program.
Allows the system to detect the presence of USB devices at startup. If
detected, the USB controller legacy mode is enabled. If no USB device is
detected, the legacy USB support is disabled.

Chapter 2: BIOS information

2-19

Legacy USB3.0 Support [Enabled]
[Enabled]
[Disabled]

Enables the support for USB 3.0 devices on legacy operating systems
(OS).
Disables the function.

EHCI Hand-off [Disabled]
[Enabled]
[Disabled]

2.5.4

Enables the support for operating systems without an EHCI hand‑off
feature.
Disables the function.

NB Configuration

IGFX Multi-Monitor [Disabled]
Enables or disables the Internal Graphics Device Multi-Monitor support for add-on VGA
devices. And the memory size of Internal Graphics Device will keep memory reserved.
Configuration options: [Disabled] [Enabled]

Primary Video Device [PCIE / PCI Video]
Selects the primary display device. Configuration options: [IGFX Video] [PCIE / PCI Video]

Integrated Graphics [Auto]
Enables the integrated graphics controller. Configuration options: [Auto] [Force]

UMA Frame Buffer Size [Auto]
This item appears only when you set the previous item to [Force]. Configuration options:
[Auto] [32M] [64M] [128M] [256M] [384M]

HDMI/DVI Port Output [Auto]
Sets the HDMI/DVI port output type. Configuration options: [Auto] [HDMI] [DVI]

PCIe x16_1/DP Output [Auto]
Sets the PCIe x16_1 slot/DP port output type. Configuration options: [Auto] [PCIe x16_1] [DP]

2.5.5

Onboard Devices Configuration

HD Audio Device [Enabled]
[Enabled]
[Disabled]

Enables the High Definition Audio Controller.
Disables the controller.
The following two items appear only when you set the HD Audio Device item to [Enabled].

Front Panel Type [HD]
Allows you to set the front panel audio connector (AAFP) mode to legacy AC’97 or highdefinition audio depending on the audio standard that the front panel audio module supports.
[HD]
Sets the front panel audio connector (AAFP) mode to high definition audio.
[AC97]
Sets the front panel audio connector (AAFP) mode to legacy AC’97.

SPDIF Out Type [SPDIF]
[SPDIF]
[HDMI]
2-20

Sets to [SPDIF] for SPDIF audio output.
Sets to [HDMI] for HDMI audio output.
ASUS F1A75-V EVO

ASM1061 Storage Controller [AHCI Mode]
[Disabled]

Disables the ASM1061 Storage controller.

[IDE Mode]
[AHCI Mode]

Enables the IDE Mode.
Enables the AHCI Mode.

ASM1061 Storage OPROM [Enabled]
[Enabled]

Enables the ASM1061 Storage OPROM.

[Disabled]

Disables the ASM1061 Storage OPROM.

Realtek LAN Controller [Enabled]
[Enabled]

Enables the Realtek LAN controller.

[Disabled]

Disables the controller.

Realtek PXE OPROM [Disabled]
This item appears only when you set the Realtek LAN Controller item to [Enabled] and
allows you to enable or disable the Rom Help of the Realtek LAN controller.
Configuration options: [Enabled] [Disabled]

Asmedia USB 3.0 Controller [Enabled]
[Enabled]

Enables the onboard USB 3.0 controller.

[Disabled]

Disables the controller.

Asmedia USB 3.0 Battery Charging Support [Enabled]
This item appears only when the Asmedia USB 3.0 Controller item is set to [Enabled].
[Enabled]
Enables the Asmedia USB 3.0 battery charging function.
[Disabled]
Disables this function

Serial Port Configuration
The sub-items in this menu allow you to set the serial port configuration.
Serial Port [Enabled]

Allows you to enable or disable the serial port (COM).
Configuration options: [Enabled] [Disabled]
Change Settings [IO=3F8h; IRQ=4]

Allows you to select the Serial Port base address. Configuration options: [IO=3F8h;
IRQ=4] [IO=2F8h; IRQ=3] [IO=3E8h; IRQ=4] [IO=2E8h; IRQ=3]

2.5.6

APM

Restore AC Power Loss [Power Off]
[Power On]
[Power Off]
[Last State]

The system goes into on state after an AC power loss.
The system goes into off state after an AC power loss.
The system goes into either off or on state, whatever the system state was
before the AC power loss.

Power On By PS/2 Keyboard [Disabled]
[Disabled]
[Space Bar]
[Ctrl-Esc]

Disables the Power On by a PS/2 keyboard.
Sets the Space Bar on the PS/2 keyboard to turn on the system.
Sets the Ctrl+Esc key on the PS/2 keyboard to turn on the system.

Chapter 2: BIOS information

2-21

[Power Key]

Sets Power key on the PS/2 keyboard to turn on the system. This feature
requires an ATX power supply that provides at least 1A on the +5VSB lead.

Power On By PME [Disabled]
[Disabled]
[Enabled]

Disables the PME to wake up by PCI/PCIE devices.
Allows you to turn on the system through a PCI/PCIE LAN or modem card.
This feature requires an ATX power supply that provides at least 1A on the
+5VSB lead.

Power On By Ring [Disabled]
[Disabled] Disables Ring to generate a wake event.
[Enabled] Enables Ring to generate a wake event.

Power On By RTC [Disabled]
[Disabled]
[Enabled]

Disables RTC to generate a wake event.
When set to [Enabled], the items RTC Alarm Date (Days) and Hour/
Minute/Second will become user-configurable with set values.

Power On By PS/2 Mouse [Disabled]
[Disabled]
[Enabled]

2.6

Disables the Power On by a PS/2 mouse.
Enables the Power On by a PS/2 mouse. This feature requires an ATX
power supply that provides at least 1A on the +5VSB lead.

Monitor menu

The Monitor menu displays the system temperature/power status, and allows you to change
the fan settings.
EFI BIOS Utility - Advanced Mode

Main

Ai Tweaker

Exit

Advanced

Monitor

CPU Temperature

+45ºC / +113ºF

MB Temperature

+34ºC / +93ºF

CPU Fan Speed

Tool

CPU Temperature

3299 RPM

Chassis Fan 1 Speed

N/A

Chassis Fan 2 Speed

N/A

Power Fan Speed

Boot

N/A

CPU Q-Fan Control

Disabled

Chassis Q-Fan Control

Disabled

CPU Voltage

+1.380 V

3.3V Voltage

+3.328 V

5V Voltage

+5.160 V

12V Voltage

+12.000 V

Anti Surge Support

Enabled

→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
F12: Print Screen

2-22

ASUS F1A75-V EVO

2.6.1

CPU Temperature / MB Temperature [xxxºC/xxxºF]

The onboard hardware monitor automatically detects and displays the CPU and motherboard
temperatures. Select Ignore if you do not wish to display the detected temperatures.

2.6.2 CPU / Chassis / Power Fan Speed [xxxx RPM] or [Ignore] /
[N/A]

The onboard hardware monitor automatically detects and displays the CPU / chassis / Power
fan speeds in rotations per minute (RPM). If the fan is not connected to the motherboard, the
field shows N/A. Select Ignore if you do not wish to display the detected speed.

2.6.3

[Disabled]
[Enabled]

CPU Q-Fan Control [Disabled]

Disables the CPU Q-Fan control feature.
Enables the CPU Q-Fan control feature.

CPU Fan Speed Low Limit [600 RPM]

This item appears only when you enable the CPU Q-Fan Control feature and allows
you to disable or set the CPU fan warning speed.
Configuration options: [Ignore] [200RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM]
CPU Fan Profile [Standard]

This item appears only when you enable the CPU Q-Fan Control feature and allows
you to set the appropriate performance level of the CPU fan.
[Standard] Sets to [Standard] to make the CPU fan automatically adjust depending on
the CPU temperature.
[Silent] Sets to [Silent] to minimize the fan speed for quiet CPU fan operation.
[Turbo]
Sets to [Turbo] to achieve maximum CPU fan speed.
[Manual] Sets to [Manual] to assign detailed fan speed control parameters.
The following four items appear only when you set CPU Fan Profile to [Manual].
CPU Upper Temperature [70ºC]
Use the <+> and <-> keys to adjust the upper limit of the CPU temperature. The values range
from 20ºC to 90ºC.
CPU Fan Max. Duty Cycle(%) [100%]
Use the <+> and <-> keys to adjust the maximum CPU fan duty cycle. The values range from
40% to 100%. When the CPU temperature reaches the upper limit, the CPU fan will operate at
the maximum duty cycle.
CPU Lower Temperature [20ºC]
Use the <+> and <-> keys to adjust the lower limit of the CPU temperature. The values range
from 20ºC to 75ºC
CPU Fan Min. Duty Cycle(%) [40%]
Use the <+> and <-> keys to adjust the minimum CPU fan duty cycle. The values range from
40% to 100%. When the CPU temperature is under the lower limit, the CPU fan will operate at
the minimum duty cycle.

Chapter 2: BIOS information

2-23

2.6.4

[Disabled]
[Enabled]

Chassis Q-Fan Control [Disabled]

Disables the Chassis Q-Fan control feature.
Enables the Chassis Q-Fan control feature.

Chassis Fan Speed Low Limit [600 RPM]

This item appears only when you enable the Chassis Q-Fan Control feature and
allows you to disable or set the chassis fan warning speed.
Configuration options: [Ignore] [200RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM]
Chassis Fan Profile [Standard]

This item appears only when you enable the Chassis Q-Fan Control feature and
allows you to set the appropriate performance level of the chassis fan.
[Standard] Sets to [Standard] to make the chassis fan automatically adjust depending
on the chassis temperature.
[Silent] Sets to [Silent] to minimize the fan speed for quiet chassis fan operation.
[Turbo]
Sets to [Turbo] to achieve maximum chassis fan speed.
[Manual] Sets to [Manual] to assign detailed fan speed control parameters.
The following four items appear only when you set Chassis Fan Profile to [Manual].
Chassis Upper Temperature [70ºC]
Use the <+> and <-> keys to adjust the upper limit of the CPU temperature. The values range
from 20ºC to 90ºC.
Chassis Fan Max. Duty Cycle(%) [100%]
Use the <+> and <-> keys to adjust the maximum chassis fan duty cycle. The values range
from 40% to 100%. When the chassis temperature reaches the upper limit, the chassis fan will
operate at the maximum duty cycle.
Chassis Lower Temperature [20ºC]
Displays the lower limit of the chassis temperature.
CPU Fan Min. Duty Cycle(%) [40%]
Use the <+> and <-> keys to adjust the minimum chassis fan duty cycle. The values range from
40% to 100%. When the chassis temperature is under 40ºC, the chassis fan will operate at the
minimum duty cycle.

2.6.5

CPU Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage

2.6.6

Anti Surge Support [Enabled]

The onboard hardware monitor automatically detects the voltage output through the onboard
voltage regulators. Select Ignore if you do not want to detect this item.
This item allows you to enable or disable the Anti Surge function.
Configuration options: [Disabled] [Enabled]

2-24

ASUS F1A75-V EVO

2.7

Boot menu

The Boot menu items allow you to change the system boot options.
EFI BIOS Utility - Advanced Mode

Ai Tweaker

Main

Exit

Advanced

Bootup NumLock State
Full Screen Logo
Wait For ‘F1’ If Error
Option ROM Messages

Monitor

Boot

Tool

Select the keyboard NumLock state

Enabled
Enabled
Force BIOS

Setup Mode

EZ Mode

Boot Option Priorities
Boot Option #1

SATA: xxxxxxx

Boot Option #2

SATA: xxxxxxx

Boot Override
> SATA: xxxxxxxxxxxx
> SATA: xxxxxxxxxxxx
> Hard Drive BBS Priorities
> CD/DVD ROM Drive BBS Priorities

→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
F12: Print Screen

2.7.1

Bootup NumLock State [On]

2.7.2

Full Screen Logo [Enabled]

[On]
[Off]

[Enabled]
[Disabled]

Sets the power-on state of the NumLock to [On].
Sets the power-on state of the NumLock to [Off].

Enables the full screen logo display feature.
Disables the full screen logo display feature.

Set this item to [Enabled] to use the ASUS MyLogo 2™ feature.

Post Report [5 sec]
This item appears only when the Full Screen Logo item is set to [Disabled] and allows you to
set the waiting time for the system to display the post report. Configuration options: [1 sec] [2
sec] [3 sec] [4 sec] [5 sec] [6 sec] [7 sec] [8 sec] [9 sec] [10 sec] [Until Press ESC]

2.7.3

Wait for ‘F1’ If Error [Enabled]

When this item is set to [Enabled], the system waits for the F1 key to be pressed when error
occurs. Configuration options: [Disabled] [Enabled]

Chapter 2: BIOS information

2-25

2.7.4

Option ROM Messages [Force BIOS]

2.7.5

Setup Mode [EZ Mode]

2.7.6

Boot Option Priorities

[Force BIOS]

The third-party ROM messages will be forced to display during the boot
sequence.
[Keep Current] The third-party ROM messages will be displayed only if the third-party
manufacturer had set the add-on device to do so.

[Advanced Mode] Sets Advanced Mode as the default screen for entering the BIOS setup
program.
[EZ Mode]
Sets EZ Mode as the default screen for entering the BIOS setup program.

These items specify the boot device priority sequence from the available devices. The
number of device items that appears on the screen depends on the number of devices
installed in the system.
• To select the boot device during system startup, press when ASUS Logo appears.
• To access Windows OS in Safe Mode, press after POST.

2.7.7

Boot Override

These items displays the available devices. The number of device items that appears on
the screen depends on the number of devices installed in the system. Click an item to start
booting from the selected device.

2-26

ASUS F1A75-V EVO

2.8

Tools menu

The Tools menu items allow you to configure options for special functions. Select an item
then press to display the submenu.
EFI BIOS Utility - Advanced Mode

Ai Tweaker

Main

Advanced

Exit

Monitor

Boot

Tool

Be used to update BIOS
> ASUS EZ Flash 2 Utility
> ASUS O.C. Profile
> ASUS SPD Information

2.8.1

ASUS EZ Flash 2 Utility

Allows you to run ASUS EZ Flash 2. Press [Enter] to launch the ASUS EZ Flash 2 screen.
For more details, see section 2.1.2 ASUS EZ Flash 2.

2.8.2

ASUS O.C. Profile

This item allows you to store or load multiple BIOS settings.
The Setup Profile Status items show Not Installed if no profile is created.

Save to Profile
Allows you to save the current BIOS settings to the BIOS Flash, and create a profile. Key in a
profile number from one to eight, press , and then select Yes.

Load from Profile
Allows you to load the previous BIOS settings saved in the BIOS Flash. Key in the profile
number that saved your CMOS settings, press , and then select Yes.
• DO NOT shut down or reset the system while updating the BIOS to prevent the system
boot failure!
• We recommend that you update the BIOS file only coming from the same memory/CPU
configuration and BIOS version.

2.8.3

ASUS SPD Information

DIMM Slot # [DIMM_A1]
Displays the Serial Presence Detect (SPD) information of the DIMM module installed on the
selected slot. Configuration options: [DIMM_A1] [DIMM_A2] [DIMM_B1] [DIMM_B2]

Chapter 2: BIOS information

2-27

2.9

Exit menu

The Exit menu items allow you to load the optimal default values for the BIOS items, and
save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit
menu.
Exit

Load Optimized Defaults

Save Changes & Reset

Discard Changes & Exit

ASUS EZ Mode

Launch EFI Shell from filesystem device

Load Optimized Defaults
This option allows you to load the default values for each of the parameters on the Setup
menus. When you select this option or if you press , a confirmation window appears.
Select Yes to load the default values.

Save Changes & Reset
Once you are finished making your selections, choose this option from the Exit menu to
ensure the values you selected are saved. When you select this option or if you press ,
a confirmation window appears. Select Yes to save changes and exit.

Discard Changes & Exit
This option allows you to exit the Setup program without saving your changes. When you
select this option or if you press , a confirmation window appears. Select Yes to
discard changes and exit.

ASUS EZ Mode
This option allows you to enter the EZ Mode screen.

Launch EFI Shell from filesystem device
This option allows you to attempt to launch the UEFI Shell application (shellx64.efi) from one
of the available devices that have a filesystem.

2-28

ASUS F1A75-V EVO

ASUS contact information
ASUSTeK COMPUTER INC.
Address
Telephone
Fax
E-mail
Web site

Technical Support

Telephone
Online support

15 Li-Te Road, Peitou, Taipei, Taiwan 11259
+886-2-2894-3447
+886-2-2890-7798
info@asus.com.tw
www.asus.com.tw
+86-21-38429911
support.asus.com

ASUS COMPUTER INTERNATIONAL (America)
Address
Telephone
Fax
Web site

Technical Support

Telephone
Support fax
Online support

800 Corporate Way, Fremont, CA 94539, USA
+1-510-739-3777
+1-510-608-4555
usa.asus.com
+1-812-282-2787
+1-812-284-0883
support.asus.com

ASUS COMPUTER GmbH (Germany and Austria)
Address
Fax
Web site
Online contact

Technical Support

Telephone (Component)
Telephone (System/Notebook/Eee/LCD)
Support Fax
Online support

Harkort Str. 21-23, D-40880 Ratingen, Germany
+49-2102-959911
www.asus.de
www.asus.de/sales

+49-1805-010923*
+49-1805-010920*
+49-2102-9599-11
support.asus.com

* EUR 0.14/minute from a German fixed landline; EUR 0.42/minute from a mobile phone.

(510)739-3777/(510)608-4555

800 Corporate Way, Fremont, CA 94539.

Asus Computer International

Date :

Signature :

Representative Person’s Name :

Jun. 20, 2011

Steve Chang / President

This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Supplementary Information:

FCC Part 15, Subpart E, Intentional Radiators

FCC Part 15, Subpart B, Unintentional Radiators
FCC Part 15, Subpart C, Intentional Radiators

Model Number : F1A75-V EVO
Conforms to the following specifications:

Product Name : Motherboard

hereby declares that the product

Phone/Fax No:

Address:

Responsible Party Name:

Per FCC Part 2 Section 2. 1077(a)

DECLARATION OF CONFORMITY

Ver. 110101

Manufacturer:

ASUS COMPUTER GmbH
HARKORT STR. 21-23, 40880 RATINGEN
GERMANY

Authorized representative in Europe:
Address, City:
Country:

Model name :

EN 60065:2002+A1:2006+A11:2008

EN 301 489-1 V1.8.1(2008-04)
EN 301 489-3 V1.4.1(2002-08)
EN 301 489-4 V1.3.1(2002-08)
EN 301 489-7 V1.3.1(2005-11)
EN 301 489-9 V1.4.1(2007-11)
EN 301 489-17 V2.1.1(2009-05)
EN 301 489-24 V1.4.1(2007-09)
EN 302 326-2 V1.2.2(2007-06)
EN 302 326-3 V1.3.1(2007-09)
EN 301 357-2 V1.3.1(2006-05)
EN 302 623 V1.1.1(2009-01)

EN 55024:1998+A1:2001+A2:2003
EN 61000-3-3:2008
EN 55020:2007

Signature : __________

Position : CEO
Name :
Jerry Shen

(EC conformity marking)

EN 62301:2005

Regulation (EC) No. 278/2009

Declaration Date: Jun.20, 2011
Year to begin affixing CE marking:2011

CE marking

EN 62301:2005

Regulation (EC) No. 642/2009

EN 62301:2005

Regulation (EC) No. 1275/2008

2009/125/EC-ErP Directive

EN 60950-1:2006+A11:2009

EN 60950-1:2006

2006/95/EC-LVD Directive

EN 300 328 V1.7.1(2006-05)
EN 300 440-1 V1.4.1(2008-05)
EN 300 440-2 V1.2.1(2008-03)
EN 301 511 V9.0.2(2003-03)
EN 301 908-1 V3.2.1(2007-05)
EN 301 908-2 V3.2.1(2007-05)
EN 301 893 V1.4.1(2005-03)
EN 302 544-2 V1.1.1(2009-01)
EN 50360:2001
EN 50371:2002
EN 50385:2002

1999/5/EC-R &TTE Directive

EN 55022:2006+A1:2007
EN 61000-3-2:2006
EN 55013:2001+A1:2003+A2:2006

2004/108/EC-EMC Directive

conform with the essential requirements of the following directives:

Motherboard
F1A75-V EVO

Product name :

Ver. 110101

TAIWAN

Country:

declare the following apparatus:

No. 150, LI-TE RD., PEITOU, TAIPEI 112, TAIWAN R.O.C.

Address, City:

ASUSTek COMPUTER INC.

EC Declaration of Conformity
We, the undersigned,

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Extract
Page Count                      : 72
Page Mode                       : UseOutlines
Page Layout                     : SinglePage
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:0352f9d0-995b-4b46-a473-01cfe77d2dba
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Create Date                     : 2011:06:29 17:42:17+08:00
Modify Date                     : 2011:06:30 09:11:49+08:00
Metadata Date                   : 2011:06:30 09:11:49+08:00
Creator Tool                    : Adobe InDesign CS2 (4.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7488 bytes, use -b option to extract)
Instance ID                     : uuid:574a2254-a234-11e0-8c77-0011247a725c
Rendition Class                 : proof:pdf
Document ID                     : adobe:docid:indd:9fd063c1-9a77-11e0-a9c0-b88d717a1a92
Derived From Instance ID        : eff559f5-9a6e-11e0-a9c0-b88d717a1a92
Derived From Document ID        : adobe:docid:indd:9d4c1827-7d6e-11e0-b135-f325ac5cca97
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 96.00, 72.00, 72.00, 72.00, 72.00, 72.00, 96.00, 96.01, 72.00, 96.01, 96.01, 96.01, 72.00, 96.01, 72.00, 96.01, 96.01, 96.01, 96.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 96.00, 72.00, 72.00, 72.00, 72.00, 72.00, 96.00, 96.01, 72.00, 96.01, 96.01, 96.01, 72.00, 96.01, 72.00, 96.01, 96.01, 96.01, 96.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:6A078178644811DCB74EACD1FD96C2F9, uuid:B5DBE146286F11DFB153D6099BD2ADD0, uuid:184922AA22DC11DFBAB9A7753DD81601, uuid:D80DE65705BB11DE8A4DF997CBC12A0C, uuid:184922AE22DC11DFBAB9A7753DD81601, uuid:A9361B1C0E4F11DF800AD3C19324F056, uuid:1D3095480DA211DF99A19EA026B7E1D7, uuid:E2F26F44860211DF976EF1D90D50858D, uuid:96C1056305B711DE8A4DF997CBC12A0C, uuid:617E7E2805B611DE8A4DF997CBC12A0C, uuid:F338008F05A211DE8A4DF997CBC12A0C, uuid:A9361B200E4F11DF800AD3C19324F056, uuid:9809F64905BF11DE8A4DF997CBC12A0C, uuid:A9361B220E4F11DF800AD3C19324F056, uuid:73581E64D52711DF8584AADFAE82B9A5, uuid:7DF557D899CD11E08007D91335E3AD56, uuid:7AADD8DD99C911E08007D91335E3AD56, uuid:ED5027204CC011E0B9EFE1EF5C156A96, uuid:AC84E28EE176E011BC71F1A1841E943B, uuid:1B717F4C99CE11E08007D91335E3AD56, uuid:19339050DD6C11DD8CA0E51280B885FE, uuid:7AADD8E399C911E08007D91335E3AD56, uuid:6CF726EF6A8AE011B662CDFC2E880CC2, uuid:E4C617D78C4311E0861CC1D687BCAC6A, uuid:7AADD8E499C911E08007D91335E3AD56, uuid:547AAF43DBE411DD99D6F700A9AAE7D4, uuid:547AAF44DBE411DD99D6F700A9AAE7D4, uuid:547AAF45DBE411DD99D6F700A9AAE7D4, uuid:7AADD8E099C911E08007D91335E3AD56, uuid:1413080B4675E0119DB5A1D83E420EC0, uuid:7DF557D399CD11E08007D91335E3AD56, uuid:7AADD8DF99C911E08007D91335E3AD56, uuid:7DF557D799CD11E08007D91335E3AD56, uuid:7AADD8E199C911E08007D91335E3AD56, uuid:7DF557D699CD11E08007D91335E3AD56, uuid:7DF557DA99CD11E08007D91335E3AD56, uuid:7AADD8DE99C911E08007D91335E3AD56, uuid:1B717F4D99CE11E08007D91335E3AD56, uuid:1B717F4B99CE11E08007D91335E3AD56, uuid:7DF557D599CD11E08007D91335E3AD56, uuid:7DF557DC99CD11E08007D91335E3AD56, uuid:7DF557D299CD11E08007D91335E3AD56, uuid:7DF557D499CD11E08007D91335E3AD56, uuid:7AADD8E599C911E08007D91335E3AD56, uuid:7DF557DB99CD11E08007D91335E3AD56, uuid:7AADD8E699C911E08007D91335E3AD56, uuid:ed190147-989c-11e0-8dc6-0011247a725c, uuid:051E1216AA2211DF85C6E32252DDF570, uuid:4c0c2f25-7fb4-11dd-8225-0017f2023f0c, uuid:DFA492DBA87F11DF881BB0DBE67F61A4, uuid:37f1fc58-7fb4-11dd-8225-0017f2023f0c, uuid:4c0c2f25-7fb4-11dd-8225-0017f2023f0c, uuid:4c0c2f25-7fb4-11dd-8225-0017f2023f0c, uuid:478431F0CF0111DFAF9BF7A76C505CF8, uuid:A18C9F18C25611DF9419CAE16EC59BF9, uuid:DFA492DBA87F11DF881BB0DBE67F61A4, uuid:5AA77C66AA2C11DF85C6E32252DDF570, uuid:98F3D186AA2F11DF85C6E32252DDF570, uuid:98F3D186AA2F11DF85C6E32252DDF570, uuid:37f1fc58-7fb4-11dd-8225-0017f2023f0c, uuid:FF2FD586AA3311DF85C6E32252DDF570, uuid:37f1fc58-7fb4-11dd-8225-0017f2023f0c, uuid:8EB51054B35511DF9FCC801DAD0B3EDC, uuid:6CA45120AA5211DF85C6E32252DDF570, uuid:10DE667BAA3511DF85C6E32252DDF570, uuid:730C53AAA09A11DF907DBD63A314A81C, uuid:0bafd0e2-85cc-4061-a773-46d980e565d2, uuid:c1732deb-5b7e-4c9f-b891-b5169c6e8d1f
Manifest Reference Document ID  : uuid:40B06DEE644811DCB74EACD1FD96C2F9, uuid:CB7DC2A6286C11DFB153D6099BD2ADD0, uuid:184922A922DC11DFBAB9A7753DD81601, uuid:D80DE65605BB11DE8A4DF997CBC12A0C, uuid:184922AD22DC11DFBAB9A7753DD81601, uuid:0A66D9FE0E4A11DF800AD3C19324F056, uuid:1D3095470DA211DF99A19EA026B7E1D7, uuid:E2F26F43860211DF976EF1D90D50858D, uuid:96C1056205B711DE8A4DF997CBC12A0C, uuid:617E7E2705B611DE8A4DF997CBC12A0C, uuid:F338008E05A211DE8A4DF997CBC12A0C, uuid:A9361B1F0E4F11DF800AD3C19324F056, uuid:9809F64805BF11DE8A4DF997CBC12A0C, uuid:A9361B210E4F11DF800AD3C19324F056, adobe:docid:photoshop:a50f5c7b-8011-11d9-a555-d949ab916104, uuid:73581E63D52711DF8584AADFAE82B9A5, uuid:FCE9BFB88E91E0119FA89908349CA6B5, uuid:201A54914FFA11DDAF82C24689851522, uuid:218288577C0111DD9710CF0B5E3031AC, uuid:218288557C0111DD9710CF0B5E3031AC, uuid:67F5D3F7500311DDAF82C24689851522, uuid:218288597C0111DD9710CF0B5E3031AC, uuid:BE96264A500611DDAF82C24689851522, uuid:6BF726EF6A8AE011B662CDFC2E880CC2, uuid:547AAF46DBE411DD99D6F700A9AAE7D4, uuid:F4588058503411DDAF82C24689851522, uuid:60B06FC50E1D11DD8F46D6CEDD328282, uuid:60B06FC10E1D11DD8F46D6CEDD328282, uuid:60B06FC30E1D11DD8F46D6CEDD328282, uuid:67F5D3F9500311DDAF82C24689851522, uuid:5A1D7230B47F11DC94DFF397CF36B636, uuid:165EC06958C411DD9F99D2E0C0CEA2FE, uuid:D48F0FF558A911DD9F99D2E0C0CEA2FE, uuid:FA0047FD3B5611E0AB19B9D339B565EA, uuid:0C068660599E11DD926B9DC7FDE82DDB, uuid:F59027C858C611DD9F99D2E0C0CEA2FE, uuid:CE1883E1500811DDAF82C24689851522, uuid:F59027C458C611DD9F99D2E0C0CEA2FE, uuid:F59027CA58C611DD9F99D2E0C0CEA2FE, uuid:2AA549BE5C4D11E082DCD91903D5AE8C, uuid:1B824A273B5811E0AB19B9D339B565EA, uuid:67F5D3F9500311DDAF82C24689851522, uuid:52D3AE7D4A75E0119DB5A1D83E420EC0, uuid:BE962654500611DDAF82C24689851522, uuid:1B824A2A3B5811E0AB19B9D339B565EA, uuid:580C8A9194E211E0AC40981A34ADAD0C, uuid:580C8A9394E211E0AC40981A34ADAD0C, uuid:3BAC57AB9A5A11E0BBB7C0EC66F07B52, uuid:051E1215AA2211DF85C6E32252DDF570, uuid:6FF7D1BB818911DD93E7ED5F7188AA04, uuid:DFA492DAA87F11DF881BB0DBE67F61A4, uuid:6FF7D1B9818911DD93E7ED5F7188AA04, uuid:6FF7D1BB818911DD93E7ED5F7188AA04, uuid:6FF7D1BB818911DD93E7ED5F7188AA04, uuid:478431EFCF0111DFAF9BF7A76C505CF8, uuid:A18C9F17C25611DF9419CAE16EC59BF9, uuid:DFA492DAA87F11DF881BB0DBE67F61A4, uuid:5AA77C65AA2C11DF85C6E32252DDF570, uuid:98F3D185AA2F11DF85C6E32252DDF570, uuid:98F3D185AA2F11DF85C6E32252DDF570, uuid:6FF7D1B9818911DD93E7ED5F7188AA04, uuid:AD1FD7B69FDF11DF8A6E9153787A385F, uuid:6FF7D1B9818911DD93E7ED5F7188AA04, uuid:8EB51053B35511DF9FCC801DAD0B3EDC, uuid:6CA4511FAA5211DF85C6E32252DDF570, uuid:0FE5FEF5A08211DF976F8730F182D818, uuid:730C53A9A09A11DF907DBD63A314A81C, uuid:056d0552-33e5-41d7-a967-21c2088074b3, uuid:ee466104-06cf-4304-8816-2f79e4a804bb
Format                          : application/pdf
Creator                         : Adobe InDesign CS2 (4.0)

EXIF Metadata provided by EXIF.tools

Asus Evo Desktop Motherboard F1A75Vevo Users Manual

F1A75VEVO to the manual 89383204-a175-425c-aade-875c2ea0f716

Navigation menu

Versions of this User Manual:

Views

Navigation