Atom AWD205TX Wireless Headphone User Manual

Atom Industrial Limited Wireless Headphone

User Manual

0309ver1 1ATOMICQuickSet-Up GuideAWD2052.4GHzDigital Headphones
0309ver1 2Congratulations on the purchase of (AWD205) 2.4GHz Digital Stereo RF WirelessHeadphones to enjoy the revolutionary technology! Please check the supplied componentagainst the following list:1 x Transmitter1 x Headphones1 x Power Supply (AC/DC 5V400mA Adaptor for Transmitter)1 x 3.5mm audio cord (built in)1 x Charging CordFUNCTION KEYSHEADPHONES(1) Headbelt(2) Ear Cushion(3) Color LED Indicator(4) Power ON/OFF Switch(5) Volume Control Knob(6) Charging Socket(7) Battery Compartment(8) Battery cover(9) Link231946587
0309ver1 3TRANSMITTER:Transmitter Front:(10) Charging LED Indicator(11) Power LED IndicatorTransmitter Rear Side:(12) Charging Cord(13) Audio IN Cord(14) Switch (source) Analog or USB(15) USB /Power IN Socket(16) LinkACCESSORIES:(17) Charging Cord(18) AC/DC Adaptor1011 121314151618
0309ver1 4INSTALLATIONPlease follow this quick set-up guide to ensure trouble free installation of yourheadphones.Step 1:Connect the Stereo Audio Cord (13) to the audio output socket (i.e. PHONE/HEADPHONE 3.5mm socket) of your audio source, e.g. TV, HiFi, CD, DVD player etc.*** If your audio source has 2 RCA output sockets (red and white in colour), use the90mm Y-connection Cord ) (not included) for connection, if necessary.Step2:Connect one end of the AC/DC Adaptor (18) to the DC IN Socket (15) at the rear side ofthe transmitter, and the other end to the main electric wall outlet.OrConnect the USB cord (not included)to computer of your audio source and the other endto the DC IN Socket (15) at the rear side of the transmitter.Suggestion: When listening music from computer,1)please try to use USB cord for power and music source at the same time.2)Please advoid to put USB cord on computer and using analog 3.5mm cord at the samecomputer to get music sources, the quality will be affected. Pls use either one method!Step3:The transmitter will be automatically ON (Green) when there is audio signal IN from theaudio source (please make sure that the transmitter is powered on by the AC/DC adaptorin Step 2). Then the Power LED Indicator (11) will glow Green (flashing) to confirm thatthe transmitter is ready for operation. Place the transmitter on a dry, cool place preferablyabove head level.*** The transmitter has auto-cut-off function. When there is no audio signal for over10minutes, the transmitter will goes into deep sleep mode. TX can wake up immediatelyafter it detects audio input again..Step 4:Open the Battery Cover (8). Insert 2 pcs AAA size batteries into the BatteryCompartment (7) at the Left hand side of the headphones observing the correct polarity.Then close the Battery Cover (8), and switch the headphones ON (4).Step 5:Switch on your music device (TV. HiFi, CD, DVD etc.) and start your media playing.Then headphone’s LED will be Green and music comes out.Step 6:
0309ver1 5Then you can hear a good quality sound. Adjust the Volume Control Knob (5) to acomfortable sound level.Remark:Pairing button is needed when more than 1 receiver towards 1 transmitter. If only 1set (1transmitter with 1 receiver), do not need to press the pairing button.** Press the button pairing (Link) on Transmitter longer than 3 seconds, LED will growGreen flashing , then press Receiver (Link) longer than 3 seconds, the ID learningprocess will be enable. Please finish the pairing process within 20 seconds. Then it willpair automatically, the LED will grow Green on Transmitter and Receiver. Music willcome out.CHARGING THE HEADPHONESBattery type: Rechargeable batteries AAANo. of cells: 2pcsRated capacity: 550 mAH / 10 – 12 hrsStep 1:Insert 2 pcs AAA size rechargeable batteries into the Battery Compartment (7) at the Lefthand side of the headphones.Step 2:Switch OFF (4) the headphones.Step 3:Connect the transmitter to a conveniently located electric wall outlet with the suppliedAC/DC Adaptor (18).Step 4:Insert one end of the Charging Cord (17) to the Charging Socket (12) of headphones.The batteries should be charged for a full 8 hours. During charging process, the ChargingLED Indicator (10) will glow RED the headphone is being charged. After full chargedLED will be off.*** Regular (non-rechargeable type) batteries can also be used to operate thisheadphone. However, you must never attempt to charge non-rechargeable batteries inthis appliance as this could prove dangerous. Only the supplied special battery can becharged.Step 5:When the batteries have been charged, remember to remove the Charging Cord from theheadphones.*** Charging procedure should never exceed 48 hours.Caution! To avoid risk of fire or injury, do not attempt to recharge non-rechargeablebatteries.
0309ver1 6Replace only with the same or equivalent type recommended by the manufacturer.Please dispose of old, defective batteries in an environmentally friendly manner inaccordance with the relevant legislationUse only the supplied adaptor. Use of other adaptor may cause damage to the unitWhen not using the unit for a long period of time, remove all batteries from unit to avoiddamage or battery leakage.Disconnect the adaptor from the wall outlet when the unit is not to be operated’Symbol indicating separate collection for electrical and electronic equipment.TROUBLE SHOOTING GUIDEIf you encounter any trouble in setting up the Headphones, please check the followingpoints:(1) Distorted sound quality or unclear sound:~ Check if the sound of your audio source is distorted and whether the volume controlis tuned to the suitable level.~ Check if the batteries in the headphones have insufficient power. Replace fresh ones ifnecessary.~ Check if the distance between the headphones and transmitter are within the effectiverange. (The effective range of the device is approx. 50M in open area.) Place theheadphones closer to the transmitter.(2) No Sound from the headphones:~ Make sure that your audio equipment, the transmitter and headphones are properlyconnected, powered and switched ON.~ Check if the batteries are inserted properly into the battery compartment.~ Check if the transmitter is powered on with the AC/DC adaptor: the Power LEDIndicator (11) will keep Green showing the transmitter is powered (only when there isaudio signal from the audio source).~ Check if all the connection cords are properly connected.If you still have problem after checking the above points, please contact your customerservice. Do not try to loosen the screws of the products to fix the problem.All the above are subject to our final change without further notice.Copyright by Atom Industrial Ltd.2008
0309ver1 7
0309ver1 8SPECIFICATIONModel AWD205Description 2.4GHz ISM bandWireless Headphones System(Rechargeable)TransmitterNo. of Channels RF frequency hopping in 15 channelsCarrier Frequency 2406 ~2472 MHzEffective Range 50 meters open areaPower Supply AC/DC AdaptorHeadphonesFrequency Responses 20 - 20,000 HzSignal to Noise Ratio >80 dBDistortion <1%Channel Separation 55dBPower Supply 2 x 1.2V AAA size rechargeable batteries OR2 x 1.5V AAA size normal batteries (Optional)System Included: 1 x Transmitter (3.5mm built in audio cord)1 x Headphones1 x AC/DC 5V 400 mA adaptor for transmitter2 x AAA batteries (Rechargeable) optional1 x Charging Cordwww.araccessories.com

Navigation menu