Aube Technologies Th140 28 Users Manual 400 140 000 C (TH140 28) ENG

TH140-28 to the manual ec434d5f-8b90-482d-829d-3fd95dccbbb6

2015-02-06

: Aube-Technologies Aube-Technologies-Th140-28-Users-Manual-500643 aube-technologies-th140-28-users-manual-500643 aube-technologies pdf

Open the PDF directly: View PDF PDF.
Page Count: 4

DownloadAube-Technologies Aube-Technologies-Th140-28-Users-Manual- 400-140-000-C (TH140-28) ENG  Aube-technologies-th140-28-users-manual
Open PDF In BrowserView PDF
400-140-000-C (TH140-28) ENG.fm Page 1 Tuesday, January 15, 2008 1:46 PM

TH140-28
Installation and User Guide
Electronic Programmable Thermostat

n

Installation

1.

1.2 Thermostat Wiring

1.1 Guidelines
TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN
POWER PANEL TO AVOID ELECTRICAL SHOCK.

NORTH AMERICA

LOW VOLTAGE < 30 V: no polarity

Installation should be carried out by an electrician.
120/240 V

• For a new installation, choose a location about 5 ft. (1.5 m) above
the floor.
• The thermostat must be installed facing the heating system and on
an inside wall.

Connection to a
circulator through
a 24 V relay

Relay

• Avoid locations where there are air drafts (top of staircase, air outlet), dead air spots (behind a door), direct sunlight or concealed
chimneys or stove pipes.

24 V transformer

Relay

Connection to the
thermostat terminals
of a furnace
Furnace

LINE VOLTAGE 120 to 240 VAC
Must be installed onto a certified electrical box.
Power supply

2 A maximum load

120/240 V

n
o

Loosen the captive screw holding the faceplate to the mounting
plate.
Pull the lower part of the faceplate to remove it from the mounting plate.

p

Loosen the screw (captive) holding the wire cover and remove
the wire cover.

q

Pull wires through the hole in the mounting plate and secure the
mounting plate to the wall (or onto an electrical box for line voltage wiring) using the enclosed wall anchors and screws.

r

Wire the thermostat to the heating system (see section 1.2) and,
if necessary, connect the remote input (see section 1.3).

s
t

Once wiring is complete, re-install the wire cover.

u
v

Connection to a
circulator (pump)
of a water heating
system

Load
Provided wires

EUROPE

For a 2-wire connection: no polarity

240 V

Relay

Connection to the
thermostat terminals
of a furnace

Use the switches located at the back of the faceplate to configure your thermostat (see section 1.4) according to your application.
Install the batteries (see section 1.5).

Direct wiring to
the circulator

Furnace

For a 3-wire connection: observe the polarity

Mount the faceplate on the mounting plate and tighten the screw.

240 V

TH140-28

400-140-000-C

Wiring to a
power-operated
mixing control valve

2008-01-15

1/4

400-140-000-C (TH140-28) ENG.fm Page 2 Tuesday, January 15, 2008 1:46 PM

1.3 Remote Input Wiring

Heating Cycle Selection (switches #1 and #2)

The TH140 is equipped with a remote input which allows connection
of a telephone controller (optional Aube CT240), a home automation
system or any other remote control system. When a signal is
received through this input, the TH140 will automatically switch from
normal operating mode to Vacation mode, or vice versa when the signal is removed.

Select the cycle using switches #1 and #2. Short cycles help
eliminate temperature variations, thus increasing user comfort. Since
shorter cycles can lead to premature system wear, it is important to
select the temperature control cycles appropriate to your heating
system. In general, the bigger your heating unit is, the longer the
cycles should be.

1.3.1 Connection to the CT240
Connect CT240 terminals A and C to TH140
terminals X and C. You must respect the
polarity.
For details on operating the telephone controller, refer to the instruction manual.

Cycles

EUROPE

AMERICA

5 minutes

Not recommended for
furnaces

Not recommended for
central units

10 minutes

Gas or electric
wall furnace

Radiant or convection
electric heating

15 minutes

Fuel or gas floor
furnace, forced air
heating

Central heating

1.3.2 Connection to a home automation system
Connect the TH140 to the home automation system as displayed in the wiring diagram.

Home automation system

20 minutes

Position

Commercial unit

1.4 Configure the Thermostat
The switches are located on the back of the faceplate. Default settings are highlighted.

1.4.2 Conventional mode with anticipation (switch #5)
This mode is compatible with all heating systems.
Programmable Span Selection (switches #1 and #2)

Switch
1&2

Description

UP

DOWN

Cycles (proportional)

15 min (see 1.4.1)

Span (conventional)

0.5°C (0.9°F) (see 1.4.2)

3

Clock display

12H

24H

4

Temperature display 1

°F

°C

5

Temperature control mode

Proportional
(see 1.4.1)

Conventional
(see 1.4.2)

6

Pump protection 2

Deactivate

Activate

Select the span using switches #1 and #2. The default temperature
span is 0.5°C (0.9°F). For example, if the temperature setpoint is
20°C (68°F), the heating system will turn on at 19.5°C (67.1°F) and
turn off at 20.5°C (68.9°F).
Span
0,3°C
(0,5°F)

Hot Water Heating

0,4°C
(0,7°F)

Gas or electric
wall furnace

1.4.1 Proportional Adaptive Mode (switch #5)

0,5°C
(0,9°F)

Fuel or gas floor
furnace

0,6°C
(1,1°F)
1.

Position

Not recommended for Not recommended for
furnaces
central units

1. If you change from °C to °F (or vice versa), you will need to reprogram
your Comfort, Economy and Vacation settings.
2. For hot water installations, it is recommended to enable this option to activate the pump for one minute every 24 hours to prevent pump seizure.

This mode analyzes previous cycles to define the the next duty cycle.
This control mode guarantees optimal temperature control based on
the system’s capacity. To extend the life of the system, a minimum
On/Off time of 10% of the cycle has been implemented. For example
with a 15-minute cycle, the system would not start or stop for less
than 1.5 minutes.

Forced Air Heating

Radiant or convection
electric heating 1

Central heating

Commercial unit

240 volt heating with relay (baseboard, convector, radiant ceiling, etc.)

Ideal for:
• Radiant or convection electrical heating system
• Circulator control in a hot water system
• Electrical hot-air furnace
• Conventional gas or fuel hot-air furnace
Not recommended for:
• Gas or fuel furnace or boiler with a wall chimney having a 30-second or higher combustion gas purging cycle. To figure out the gas
purging cycle of your system, count the time between the heating
command sent by the thermostat and the moment when the
burner actually goes on.
• Multi-zone systems, where several thermostats command a single
heating unit.
Note: In these last two cases, conventional mode with anticipation is
recommended.
TH140-28

400-140-000-C

2008-01-15

2/4

400-140-000-C (TH140-28) ENG.fm Page 3 Tuesday, January 15, 2008 1:46 PM

1.5 Install the Batteries

p

When you first install the batteries, the unit runs a
sequence of tests and a complete reset to zero. The
screen should display 0:00 MO
and the ambient temperature. The current setpoint is 20°C.

3.1 Automatic
This mode executes the schedule. To activate:
• Press Manual/Auto until
setpoint icon is displayed.

1.5.1 Replacing the batteries

When in Automatic mode, you can temporarily bypass the
current program setpoint until the beginning of the next program. To
bypass:

The time and programming are saved for
15 seconds when replacing the batteries.

• Set the desired temperature
use a pre-defined setpoint.
2.

Note: You may program the thermostat while holding it in your hands
or when it is mounted on the mounting plate.

Set the day, using the Day button.

3.3 Vacation

or

to use

Maintains a specific temperature when away for a prolonged absence (e.g. vacation).

2.2.1 Comfort and Economy
These setpoints are associated to the schedule’s programs and are
pre-programmed as follows:
Comfort

20°C (68°F)

Programs 1 and 3

Economy

18°C (64°F)

Programs 2 and 4

2.2.2 Vacation
This pre-programmed setpoint is used when the Vacation mode is
activated.
10°C (50°F)

2.2.3 To Modify a Setpoint
Set the temperature using

to

is displayed.

• Set temperature
OR quickly press
a pre-defined setpoint.

Vacation

or

This mode allows you to maintain a constant temperature.
To activate this mode:

Set the time, using the Hour and Minute buttons.

2.2 Configure the Setpoints

n
o

OR quickly press

3.2 Manual

• Press Manual/Auto until

2.1 Set the Time and Day

n
o

is displayed. The program

3.1.1 Temporary Bypass

The TH140 will display an icon indicating that
the batteries must be replaced. This icon will be
displayed for 60 days; after this delay, the
TH140 will shut down the heating unit.

o

3.

The TH140 offers three operating modes:

The ambient temperature could be higher if you are holding
the TH140 in your hands. It will return to normal about one
hour after installation.

Basic Configuration

Select the Operating Mode

.

Press and hold one of the setpoint
buttons ( or
or
) until the
icon is displayed on the screen
(approx. 3 seconds).

2.3 View the Current Setpoint
To view the current setpoint, quickly press
once one of the arrow buttons
.
The screen displays the setpoint; the arrow
indicates a setpoint.

• From the TH140, quickly press

to activate.

• Can also be activated remotely (CT240, home automation system or any other system) if the remote input is
connected to one of these systems.
Note: When the Vacation mode is activated remotely, it can only be
deactivated remotely.
Note: For details on how to activate the Vacation mode using a telephone, refer to the CT240 Instruction Manual.

q

Program Your Schedule

4.

The TH140 allows four setting changes for each day of the week.
There are no pre-set programs. Your heating system switches betwwen the Comfort setpoint and the Economy setpoint according to the
times you would have set.
For example, enter each day the time at which you wake up
(PROG 1), the time you leave for work (PROG 2), the time you return
home (PROG 3) and the time you go to bed (PROG 4):
Programs

Associated Setpoint

Time

PROG 1

(Comfort)

Wake-up

PROG 2

(Economy)

Leave

PROG 3

(Comfort)

Return

PROG 4

(Economy)

Sleep

Note: For temperature increases (PROG 1 and 3), allow at least
15 minutes per 1°C (2°F). For example, if you have lowered
the temperature by 3°C (6°F) while you sleep and you wake up
at 7 a.m., change the setting at 6:15 a.m.

TH140-28

400-140-000-C

2008-01-15

3/4

400-140-000-C (TH140-28) ENG.fm Page 4 Tuesday, January 15, 2008 1:46 PM

4.1 Set or Modify the Programs
• After 60 seconds of inactivity, the thermostat will automatically exit
programming mode.
• It is sometimes faster to program the same schedule for the entire
week and then modify the exception days.

n
o

Press Program. The screen displays MO and PROG 1.
Press Day to select the day (hold for 3 seconds to select all days
of the week).

p

Press Hour and Minute to set the start time.
To clear an entry, press Clear, the time zone displays --:-- when
the program is inactive.

q
r
s

Press Program to select the program number (2, 3 or 4).
Repeat steps 3 and 4 for remaining programs.
Press Manual/Auto to exit.

4.1.1 Programming Example
Comfort (programs 1 and 3):
• Monday to Friday between 6:00 a.m. and 8:30 a.m. and
between 4:00 p.m. and 11:00 p.m.
• Saturday and Sunday between 6:00 a.m. and 11:00 p.m.
Economy (programs 2 and 4):
• Monday to Friday between 8:30 a.m. and 4:00 p.m. and
between 11:00 p.m. and 6:00 a.m.
• Saturday and Sunday between 11:00 p.m. and 6:00 a.m.
PROG

MON

TUE

WED

THU

FRI

SAT

SUN

1

6:00

6:00

6:00

6:00

6:00

6:00

6:00

2

8:30

8:30

8:30

8:30

8:30

--:--

--:--

3

PM

4

PM

4:00

11:00

PM

PM

4:00

11:00

PM

PM

4:00

11:00

PM

PM

4:00

11:00

PM

PM

4:00

11:00

--:-PM

11:00

--:-PM

11:00

To program this schedule:

n
o

Press Program. The screen displays MO and PROG 1.

p

Set the time (6:00) for the first program (PROG 1) using the
Hour and Minute buttons.

q

Press Program to select PROG 2. Set the time (8:30) using the
Hour and Minute buttons.

r

Press Program to select PROG 3. Set the time (4:00 p.m.) using
the Hour and Minute buttons.

s

Press Program to select PROG 4. Set the time (11:00 p.m.)
using the Hour and Minute buttons.

t

Press Manual/Auto to exit.

Press and hold Day for 3 seconds to select all days of the week
(MOTUWETHFRSASU).

5.

Power supply: 2 AA or LR6 alkaline batteries 1.5 V
Max. resistive load: 5 A @ 240 VAC / 5 A @ 30 VDC
Max. inductive load: 2 A @ 240 VAC / 2 A @ 30 VDC (P.F. = 0.4)
Remote input: 12 VDC, ± 10%, 2.5 mA
Certifications: CE, c UL us
Control device: Electronic
Automatic action: Type 1 B
Number of programs: 4 programs / day, total of 28 programs
Storage temperature: -20°C to 50°C (-4°F to 122°F)
Operating temperature: 0°C to 50°C (32°F to 122°F), 95% R.H.
Temperature setting range: 5°C to 30°C (40°F to 85°F)
Temperature display resolution: 0.1 degree
Temperature reading accuracy: ± 0.5°C (± 0.9°F)
Software: Class A
Protection class: II
Protection degree: IP 40
The terminals are designed to handle a cross-section of wire measuring up to 2.5 mm2 (14 AWG).

;

Warranty

6.

Aube warrants this product, excluding battery (if applicable), to be free from defects in the
workmanship or materials, under normal use and service, for a period of three (3) years
from the date of purchase by the consumer. If at any time during the warranty period the
product is determined to be defective or malfunctions, Aube shall repair or replace it (at
Aube's option).
If the product is defective,
(i)
return it, with a bill of sale or other dated proof of purchase, to the place from which
you purchased it, or
(ii) contact Aube. Aube will make the determination whether the product should be
returned, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not
apply if it is shown by Aube that the defect or malfunction was caused by damage which
occurred while the product was in the possession of a consumer.
Aube's sole responsibility shall be to repair or replace the product within the terms stated
above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,
INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,
DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS
OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some provinces and
states do not allow the exclusion or limitation of incidental or consequential damages, so
this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS
PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS
HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some
provinces and states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary
from province or state to another.



Technical Assistance

7.

705 Montrichard
Saint-Jean-sur-Richelieu
Québec, Canada J2X 5K8

10 rue Ampère
95500 Gonesse
France

Press Program to access programming mode.

Tel. : (450) 358-4600

33 (0) 1 34 07 99 00

Press Program until PROG 2 is selected.

1-800-831-AUBE

33 (0) 1 34 07 99 19

Press Day to select SAturday (SA).

Fax : (450) 358-4650

advaube@comintes.com

To erase programs 2 and 3 for Saturday and Sunday:

n
o
p
q
r
s
t
u

r

Technical Specifications

Press Clear to erase the time (--:--).
Press Day to select SUnday (SU).
Press Clear to erase the time (--:--).

aube.service@honeywell.com
For more information on our products, visit us at
www.aubetech.com

Repeat steps 2 to 5 for PROG 3.
Press Manual/Auto to exit.

TH140-28

400-140-000-C

2008-01-15

4/4



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2008:01:15 13:55:41-05:00
Create Date                     : 2008:01:15 13:51:07-05:00
Metadata Date                   : 2008:01:15 13:55:41-05:00
Format                          : application/pdf
Title                           : 400-140-000-C (TH140-28) ENG.fm
Creator                         : e283638
Document ID                     : uuid:79c4d2f4-102d-4699-8664-7630624af740
Instance ID                     : uuid:6c916c4d-bcf7-466b-a6d5-1ad1c34d2996
Page Count                      : 4
Author                          : e283638
EXIF Metadata provided by EXIF.tools

Navigation menu