Aube Technologies Th147E P Users Manual 400 147 016 C (TH147_148 Europe) ENG
TH148ELE 400-147-016
TH147E-P to the manual 149a5e06-cc8a-4598-a858-8382f7959d84
2015-02-06
: Aube-Technologies Aube-Technologies-Th147E-P-Users-Manual-500583 aube-technologies-th147e-p-users-manual-500583 aube-technologies pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
400-147-016-C (TH147_148 P Europe) ENG.fm Page 1 Tuesday, January 8, 2008 2:47 PM TH147E-P & TH148ELE-P Installation and User Guide Programmable Thermostats n Introduction 1. o Installation 2. The TH147E-P and TH148ELE-P thermostats can be used to control: Note: The installation must be performed by an electrician. • a forced air system - 2 or 3 wires 2.1 Removing the Old Thermostat • a hot water system with or without pump - 2 wires IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT POWER TO THE HEATING SYSTEM. • a millivolt system - 2 wires Adjustment buttons Display Economy temperature preset Program button Remove the old thermostat to access the wires. p If necessary, strip the end of each wire (maximum of 6 mm). Identify and label each wire (with the corresponding letter on the wire terminal) and remove them from the terminals. 2.2 Installing the New Baseplate Backlight button Comfort temperature preset n o Choose a location approximately 1.5 m above the floor and on an inside wall. Avoid draughty areas (top of staircase, air outlet, etc.), dead air spots (behind doors), direct sunlight or areas near concealed pipes or chimneys. Mode selection / program exit Display : Comfort temperature indicator Appears when the setpoint temperature is displayed : Economy temperature indicator Temperature Time n o Remove the thermostat faceplate. p q Gently tilt the thermostat upwards. Day Loosen the locking screw in order to separate the thermostat from its baseplate (the screw cannot be completely removed). Manual mode Automatic mode Unoccupied mode Features TH148ELE-P Low battery indicator TH147E-P Heating is On Schedule Pump protection X X Programmable cycle length X X Battery replacement indicator X X Backlit display X X Programming: - Preprogrammed schedule - Temporary bypass - Time display (12 h or 24 h) X X X X X X X X R Power W Load Interchangeable faceplates X X Un / Un Unoccupied mode activated remotely X Automatic daylight savings changeover X TH147E-P & TH148ELE-P Pass the wires through the opening of the baseplate and secure the baseplate to the wall using the appropriate screws. 2.3 Terminal Designations Unoccupied mode input (TH148ELE-P only) 400-147-016-C 2008-01-08 1/4 400-147-016-C (TH147_148 P Europe) ENG.fm Page 2 Tuesday, January 8, 2008 2:47 PM 2.4 Connecting the Heating System 2.7 Completing the Installation NOTE: No polarity to observe. Load 2.5 Unoccupied Mode Input (TH148ELE-P only) TH148ELE-P has an input that can be used to lower the temperature when the house is unoccupied. You can connect an Aube’s CT240 telephone controller (optional) or another remote control system. When the thermostat receives a 12-VDC signal, it switches to the unoccupied mode where the setpoint programmed for that mode is used (see section 5). When the signal is removed, the thermostat returns to the previous mode. n Once the baseplate and the batteries are installed, mount the thermostat on the baseplate. o Secure the thermostat using the locking screw and install the faceplate. p Apply power back to the system. 2.5.1 Connecting to CT240 p Connect TH148ELE-P terminals UN and UN to CT240 terminals A and C (no polarity to observe). 3.1 Backlight Basic Functions 3. The display illuminates for 12 seconds when the backlight button or any other button is pressed. 2.5.2 Connecting to a Home Automation System Connect TH148ELE-P terminals UN and UN to a 12-VDC circuit as shown (no polarity to observe). 2.6 Installing the Batteries 3.2 Displaying the Temperature The actual (measured) temperature is normally displayed. To view the setpoint temperature, press once on either of the buttons. The setpoint, along with the icon, will be displayed for the next 5 seconds. 3.3 Setting the Temperature Press one of the played. : buttons until the desired temperature is dis- 3.4 Comfort and Economy Temperatures The thermostat has 2 preset temperature buttons: n o p Gently pull out the battery cover. Install the batteries as shown. Observe the polarity. Re-install the battery cover. You will hear a clicking sound. After the batteries are installed, the thermostat performs a series of tests for approximately 5 seconds. Afterwards, the thermostat displays the temperature. It is possible that the displayed temperature is higher than the ambient temperature if you are holding the thermostat in your hands. Once installed on the wall, the thermostat will display the ambient temperature. The time and day settings flash to indicate that they must be set (see section 4.1). TH147E-P & TH148ELE-P • Comfort temperature • Economy temperature To set the thermostat at the Comfort or Economy temperature, press the corresponding preset button. The corresponding symbol will be displayed. The following table shows the use and the factory setting of each preset button. Button Intended use Default setting Comfort (when the occupant is awake and at home) 21°C Economy (when the occupant is absent or asleep) 17°C To modify the Comfort or Economy temperature: n o Set the desired temperature using the buttons. Press and hold the appropriate preset button until the corresponding symbol is displayed. 400-147-016-C 2008-01-08 2/4 400-147-016-C (TH147_148 P Europe) ENG.fm Page 3 Tuesday, January 8, 2008 2:47 PM 3.5 Control Mode 4.2 Setting the Date (TH148ELE-P only) 3.5.1 Manual This setting is necessary only if you use the automatic daylight savings changeover (see section 5). Use this mode to set the temperature manually. To use this mode, press Mode to display and set the desired temperature using the buttons or the buttons. 3.5.2 Automatic Use this mode to set the temperature according to the programmed schedule (see section 4.3). To place in Automatic mode, press Mode to display . Temporary Bypass If you modify the setpoint temperature when the thermostat is in automatic mode, the new temperature will be used for the next 2 hours. Afterwards the thermostat will return to the automatic mode and use its current temperature setting. The flashes during the bypass. n o Press Clk for 3 seconds. The time setting is displayed. p Set the year using the month setting. q Set the month using the date setting. r s Set the day using Press Clk for 3 seconds again. The year setting is displayed. and press Clk to display and press Clk to display . Press Exit to exit the programming mode. 4.3 Schedule icon 3.5.3 Unoccupied (TH148ELE-P only) To place the thermostat in Unoccupied mode, see section 2.5. When the thermostat is in this mode, the unoccupied mode setpoint is used and the icon is displayed. When the thermostat is placed in automatic mode, it switches between the Comfort temperature and the Economy temperature according to the programmed schedule. You can set a different program for each day of the week. The following schedule has been programmed in the thermostat as follows: Temporary Bypass If you modify the setpoint temperature when the thermostat is in unoccupied mode, the new temperature will be used for the next 2 hours. Afterwards, the thermostat will return to the unoccupied mode setpoint. The icon flashes during the bypass. Comfort : 6:00 to 8:00 18:00 to 22:00 Monday to Friday Economy : 8:00 to 18:00 22:00 to 6:00 3.6 Low-battery Indicator Comfort An icon appears when the batteries need replacement. This icon will flash for 60 days, then the thermostat will cut power to the heating system. The icon disappears once the batteries are replaced. Saturday and Sunday After replacing the batteries, re-adjust the clock and day (see section 4.1). For TH148ELE-P model, re-adjust the date also (see section 4.2). The rest of the settings are unaffected when the batteries are removed. q Programming 4. . If not already done, set the Comfort and Economy temperatures (see section 3.4). o Press Pgm. The program for Monday will appear and the first period (0:00 a.m. to 1:00 a.m.) is selected (flashes). Each period is a one-hour interval. Note: If you wish to use the same program every day, press Pgm for 3 seconds to select all the days of the week. p Press tively. q Select the Comfort or Economy temperature by pressing on the Press Clk. The minute display flashes. Set the minutes using . Press Clk. The day display flashes. Set the day using . Press Exit to exit the programming mode. TH147E-P & TH148ELE-P : n Press Clk for 3 seconds. The hour display flashes. Set the hour using Economy 22:00 to 6:00 4.4 Modifying the Schedule 4.1 Setting the Clock and Day n o p q r s t : 6:00 to 22:00 or to advance to the next or preceding period respec- corresponding button ( or ). r s Repeat steps 3 and 4 as required. t Press Exit to exit the programming mode. To modify the program for another day, press Pgm until the day is selected and repeat steps 3 to 5. 400-147-016-C 2008-01-08 3/4 400-147-016-C (TH147_148 P Europe) ENG.fm Page 4 Tuesday, January 8, 2008 2:47 PM r Configuration 5. n Press the backlight button until the configuration menu appears (3 seconds). o To go to the next parameter (menu item), press the backlight button (1 second). p q r To modify a parameter, press . Repeat steps 2 and 3 if necessary. To end, press the backlight button until the configuration menu disappears (3 seconds). DISPLAY DESCRIPTION Time display Pump protection 1 Automatic daylight savings changeover 2 (TH148ELE-P only) Unoccupied mode temperature setting 3 (TH148ELE-P only) DEFAULT SELECTIONS 12 h 12 h or 24 h Off On or Off Off On or Off 10°C 5°C to 28°C 4 2, 3, 4, 5 or 6 Number of cycles per hour 4 1 When pump protection is On, the thermostat will activate the heating system for 15 seconds if it has not been activated for the past 24 hours. 2 Daylight savings time starts on the last Sunday of March and normal time starts on the last Sunday of October. 3 See section 2.5. 4 The corresponding cycle lengths are: 2=30 min., 3=20 min., 4=15 min., 5=12 min., 6=10 min. Select the cycle according to the type of heating: gas boiler <30kW: 10 minutes; oil boiler: 20 minutes s Technical Specifications Power supply: 2 LR6 (1.5V) Alkaline batteries Maximum load: 5 A (resistive), 0.95 A (inductive) @ 240 VAC Power across UN terminals: 20 mA @ 12 VDC Setpoint range: 5 to 28°C Display range: -10 to 50°C Display resolution: 0.5°C Accuracy: ± 0.5°C Cycle length: 10, 12, 15, 20 or 30 minutes (programmable) Conformity: IEC60730-1 Storage temperature: -20 to 50°C Dimensions: 127 mm x 75 mm x 28 mm 6. ; Warranty 7. Aube warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of three (3) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Aube shall repair or replace it (at Aube's option). If the product is defective, (i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it, or (ii) call Aube Technical Support at 33 (0) 1 34 07 99 00. Technical Support will make the determination whether the product should be returned to the following address: 10 rue Ampère, 95500 Gonesse, France, or whether a replacement product can be sent to you. This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Aube that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer. Aube's sole responsibility shall be to repair or replace the product within the terms stated above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some regions do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some regions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from region to region. If you have any questions concerning this warranty, please write Aube, 705 Montrichard, Saint-Jean-sur-Richelieu, Quebec J2X 5K8 Canada. Technical Assistance 8. For any questions regarding the product installation or operation, contact our technical support team at Tel.: 33 (0) 1 34 07 99 00 Fax: 33 (0) 1 34 07 99 19 Email: advaube@comintes.com For more information on our products, visit us at www.aubetech.com TH147E-P & TH148ELE-P 400-147-016-C 2008-01-08 4/4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Annotate, Fill forms, Extract, Print high-res XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2008:01:21 15:07:36-05:00 Create Date : 2008:01:08 14:57:43-05:00 Metadata Date : 2008:01:21 15:07:36-05:00 Format : application/pdf Title : 400-147-016-C (TH147_148 P Europe) ENG.fm Creator : e283638 Document ID : uuid:17231fc7-7929-4048-9d7d-39cf9afe1d2d Instance ID : uuid:5dc2007d-b72f-402e-a044-457653e7942d Page Count : 4 Author : e283638EXIF Metadata provided by EXIF.tools