Audio Technica BM03R8645 Wireless Module User Manual BM03R8645 UserMan 20171207

Download:
Mirror Download [FCC.gov]
Document ID	3668450
Application ID	NGdWiFd1F5fLPBF8WHWbBA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.99kB (162316 bits)
Date Submitted	2017-12-08 00:00:00
Date Available	2018-06-06 00:00:00
Creation Date	2017-12-08 09:25:28
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2017-12-08 09:31:34
Document Title	Microsoft Word - BM03R8645- UserMan_20171207
Document Creator	PScript5.dll Version 5.2.2
Document Author:	A316176

BM03R8645
Manual
Since this device is always used with Audio-Technica Wireless Device, it is not sold to general
end users separately.
Therefore there is no user manual of this device by alone.
And this device will install on Audio-Technica development products only. The following
statements must be described on the user manual of the Audio-Technica Wireless Device;
Important notice
．
For use in the United States. 1
Module User Requirements
FCC 15.212(a)(
ⅵ)(A)
The host device must contain the following permanent labeling on the exterior of the
host device as follows:
Contains FCC ID: ○○○○○△△△△△△△
FCC 15.19(a)(3)
The host device shall bear the following statement in a conspicuous location on the
device:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received,including interference that may cause undesired
operation.
When the device is so small or for such use that it is not practicable to place the
statement specified under paragraph 15.19(a)(3) of this section on it, the information
required by this paragraph shall be placed in a prominent location in the instruction
manual or pamphlet supplied to the user or, alternatively,shall be placed on the
container in which the device is marketed.
．
The user manual of the host device must contain the following paragraph:
FCC 15.21
Caution: Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC15.105(b)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and,if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTE:
ⅰ.That module is limited to OEM installation only.
ⅱ.That OEM integrators is responsible for ensuring that the end-user has no manual
instructions to remove or install module.
ⅲ.That module is limited to installation in mobile or fixed applications, according to
Part 2.1091(b)
ⅳ.That separate approval is required for all other operating configurations,
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module. The end user manual shall include required
regulatory information/warning as below.
ⅰ.End-users must be provided with transmitter/antenna installation requirements
and operating conditions for satisfying RF exposure compliance.
ⅱ.A separate section should clearly state “FCC RF Exposure requirements:”
ⅲ.Required operating conditions for end users
ⅳ. Antenna/or transmitter installation requirements, where relevant (For example:
The antenna used with this module must be installed to provide a separation
distance of at least 20cm from all persons, and must not transmit simultaneously
with any other antenna or transmitter.)
Information for OEMs and Host integrators
The guidelines described within this document are provided to OEM integrators installing
Audio-Technica Wireless Module in wireless headphone platforms. Adherence to these
requirements is necessary to meet the conditions of compliance with FCC rules, including RF
exposure. When all antenna type and placement guidelines described herein are fulfilled the
Audio-Technica Wireless Module may be incorporated into wireless headphone platforms with
no further restrictions. If any of the guidelines described herein are not satisfied it may be
necessary for the OEM or integrator to perform additional testing and/or obtain additional
approval. The OEM or integrator is responsible to determine the required host regulatory
testing and/or obtaining the required host approvals for compliance
The module grantee will provide assistance if requested.
For Use in Canada：
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may
cause undesired operation of the device.
For Canada
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique
à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à
l'établissement d'une communication satisfaisante.
IMPORTANT NOTE: Radiation Exposure Statement Radio
Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC)
radio frequency exposure limits. The Wireless Device should be used in such a manner such
that the potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure limits
under portable exposure conditions. (antennas are less than 20 cm of a person's body).
Informations concernant l'exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition
aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à
minimiser les contacts humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF
d'IC dans des conditions d'exposition à des appareils portables. (les antennes sont moins de 20
cm du corps d'une personne).
The Bluetooth Module (Model No.:BM03R8645) provides a fully compliant Bluetooth
V4.1(don’t support BLE ) specification system for data and voice.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Author                          : A316176
Create Date                     : 2017:12:08 09:25:28Z
Modify Date                     : 2017:12:08 09:31:34+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : A316176
Title                           : Microsoft Word - BM03R8645- UserMan_20171207
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2017:12:08 09:31:34+08:00
Producer                        : GPL Ghostscript 8.15
Document ID                     : uuid:fd8663f5-f444-4742-bbd2-390123403a3d
Instance ID                     : uuid:bc4ab623-2d66-411d-9018-20a424738a55
Page Count                      : 7

EXIF Metadata provided by EXIF.tools