Audio Technica T3201DE2 3000 SERIES BODYPACK TRANSMITTER User Manual

Audio-Technica Corporation 3000 SERIES BODYPACK TRANSMITTER

User Manual

User ManualUHF synthesized diversity wireless systemATW-R3210UHF Synthesized diversity receiverATW-T3201UHF transmitterATW-T3202UHF transmitter3000 Series
IntroductionThank you for purchasing this Audio-Technica product.Before using the product, read through this user manual to ensure that you will use the product correctly. Please keep this manual for future reference.Package contentsBefore use, check to make sure that all of the following items are contained in the package.If any of the items is missing from your package or damaged, contact your local Audio-Technica dealer.• ATW-R3210• ATW-T3201• ATW-T3201• AC adapter (for ATW-R3210)• Rack mount (large, small)• Screw kit for Rack mount• AT8456a microphone holder (for ATW-T3202)• AT8456a screws for microphone holder (for ATW-T3202)• Antennas• Quick Start Guide• Warranty
2Warning: • To prevent fire or shock hazard, do not expose this apparatus to rain or moisture.Caution:• Do not expose this apparatus to drips or splashes. • To avoid electric shock, do not open the cabinet.• Refer servicing to qualified personnel only.• Do not expose this apparatus to excessive heat such as sunshine, fire or the like.• Do not subject this apparatus to strong impact.• This apparatus should be located close enough to the AC outlet so that you can easily grasp the AC adapter at any time. • Do not place any objects filled with liquids, such as vases, on this apparatus.• To prevent fire, do not place any naked flame sources (such as lighted candles) on this apparatus.• Do not install this apparatus in a confined space such as a bookcase or similar unit. • Install this apparatus only in places with good ventilation. • The rating label is put on the bottom of this apparatus. Battery Caution:• Keep batteries out of the reach of children. • Observe correct polarity as marked.• Do not expose the battery to excessive heat such as sunshine, fire or the like.• Always consider the environment issues and follow local regulations when disposing of batteries.• Remove depleted battery immediately.• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.• Use only disposable LR06(AA) alkaline batteries.• Do not use rechargeable batteries.• Do not use new batteries and old one at the same time.• Do not use different batteries type or model.• Do not use a leaking battery. If battery leakage occurs, avoid contact with skin. If contact occurs, immediately wash thoroughly with soap and water.• If contact occurs, immediately wash thoroughly with soap and water.• If battery leakage comes into contact with your eyes, immediately flush with water and seek medical.For customers in the USAFCC NoticeWarning:This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.Caution:You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.For customers in CanadaIC statementCAN RSS-Gen/CNR-Gen This device complies with INDUSTRY CANADA R.S.S. 210. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference which may cause undesired operation.This device complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment.Important information
3Avertissement: • Pour éviter tout risque de choc électrique ou d’incendie, n’exposez pas cet appareil à la pluie ou à l’humidité.Attention:• Protégez cet appareil des projections et des gouttes d’eau. • Confiez tous travaux d’entretien à un technicien qualifié.• N’exposez pas cet équipement à des températures excessives, telles que celles de la lumière directe du soleil, d’une flamme ou autres sources de chaleur.• Ne soumettez pas cet équipement à de forts impacts.• Cet appareil doit être placé à proximité de la prise secteur afin que vous puissiez facilement vous saisir de l'adaptateur secteur à tout moment.• Ne placez pas d’objets remplis de liquide tels que des vases, sur l’appareil. • Pour éviter tout risque d’incendie, ne placez pas de flammes nues (telles que des bougies allumées) sur l’appareil.• N’installez pas cet appareil dans un espace confiné tel qu’une étagère ou un endroit similaire. • N'installez cet appareil que dans des endroits bien aérés. • La plaque signalétique se trouve sur le dessous de cet appareil. Mise en garde relative aux piles:• Tenez les piles hors de portée des enfants. • Respectez la polarité correcte indiquée.• N'exposez pas la pile à une chaleur excessive telle que les rayons du soleil, un feu ou autre source de chaleur.• Prenez toujours en considération l'impact environnemental et suivez les réglementations locales lors de la mise au rebut des piles.• Retirez immédiatement toute pile déchargée.• Danger d'explosion en cas de positionnement incorrect de la pile. Remplacez uniquement avec des piles de type identique ou équivalent.• Utilisez uniquement des piles alcalines LR06 (AA) jetables.• N'utilisez pas des piles rechargeables.• Ne mélangez pas des piles neuves et des piles usagées.• Ne mélangez pas différents types ou modèles de piles.• N'utilisez pas une pile qui fuit. En cas de fuite de la pile, évitez tout contact avec la peau.• En cas de contact, rincez aussitôt abondamment au savon et à l'eau.• Si le liquide de la pile entre en contact avec vos yeux, lavez aussitôt avec de l'eau et consultez un médecin.Pour les clients aux États-UnisAvis de la FCCAvertissement:Cet appareil est conforme à la Partie15 du règlement de la FCC. Son fonctionnement est soumis aux deux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférence nocive et (2) cet appareil doit accepter les interférences reçues, y compris les interférences pouvant provoquer un fonctionnement indésirable.Attention:Vous êtes averti que tout changement ou modification non expressément approuvé dans ce manuel est susceptible d’annuler votre droit d’utilisation de cet appareil.Note: Cet appareil a fait l’objet de tests afin de vérifier sa conformité avec les limites relatives aux appareils numériques de classe B, conformément à la partie 15 du règlement de la FCC. Ces limites ont pour vocation d’offrir une protection raisonnable contre les interférences nocives en installation résidentielle. Cet appareil génère, utilise et peut émettre des fréquences radioélectriques et provoquer, en cas d’installation et d’utilisation non conformes aux instructions, des interférences préjudiciables à la réception des signaux radio. Toutefois, il n’y a pas de garantie que des interférences ne se produiront pas dans une installation particulière. Si l’appareil provoque des interférences préjudiciables à la réception radio ou télévisée, ce qui peut être déterminé en éteignant et allumant l’appareil, l’utilisateur est invité à essayer d’y remédier en prenant une ou plusieurs des mesures suivantes:- Réorienter ou déplacer l’antenne réceptrice.- Augmenter la séparation entre l’appareil et le récepteur.- Brancher l’appareil dans une prise, sur un circuit différent de celui auquel est raccordé le récepteur. - Demander de l’aide au revendeur ou à un technicien radio/TV qualifié.À l’attention des clients au CanadaDéclaration ICCAN RSS-Gen/CNR-Gen Cet appareil est conforme à la norme R.S.S. 210 d'INDUSTRIE CANADA. Le fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d'interférences dommageables et (2) cet appareil doit accepter toutes les interférences reçues, y compris les interférences susceptibles de générer un fonctionnement préjudiciable.Cet appareil est conforme aux limites de RSS-102 sur l'exposition aux rayonnements établies pour un environnement non contrôlé.Informations importantes
4Safety precautions• When using the product, also read the user manuals supplied with the devices that are to be connected.• When not using the product, remove the power plug from the power outlet.• Turn the product off before connecting or disconnecting cables.• If you use the product near a TV or radio antenna, noise may be generated in the TV or radio. In this case, move the product away from the TV or radio antenna.• Two transmitters on the same frequency cannot be used simultaneously.• Please be aware that interference may be generated from the surrounding electromagnetic environment and/or from using multiple units.• The wireless system may be affected by electromagnetic noise from automobile spark plugs, light dimmers, computers, OA devices, or electrical music instruments. Position the components of the system in a place where it is less likely to be affected.• Only use this product in combination with devices specified by the manufacturer.• Insert the plugs of connecting cables securely into their mating connectors.• Radio waves in the UHF band propagate mainly by line of sight. Configure system so there are no obstructions between the transmitter and receiver.• Turn the phantom power off when connecting to the mixer.• Use 120 V AC power source. Refer to "Specifications" for product ratings.• If there is an electronic device or a transmitter (mobile phone etc.) in the vicinity of this product, this product may be subject to noise. In this case, move the product away from the devices.• When installing this product, make sure there are no obstacles between the receiver and the transmitter that block radio waves.• If you use the product near a TV or radio antenna, noise may be generated in the TV or radio. In this case, move the product away from the devices.• To prevent the batteries from wearing out, turn the product off when not in use.• Over time, discoloration may occur due to ultraviolet rays (especially direct sunlight) and friction.• Any customization of the product is prohibited by law. Also, disassembly of the product may result in electrical shock, equipment damage or fire. Never disassemble the product.Care• If the product becomes dirty or dusty, disconnect the power plug first, and then wipe the product off with a dry soft cloth.• Do not use benzine, thinner, contact restoring protective agent, or any other chemical agent. Doing so may cause deformation, damage, or malfunction.• When storing the product for an extended period of time, wrap it with a plastic cover, and do not allow it to be exposed to humidity.
5Part names and functionsATW-R3210Front panel❶ Power switch ( ) Press the switch to turn the power on.❷ IR sync windowUse when syncing transmitter (ATW-T3201/ATW-T3202) to the product.❸ DisplayDisplays the product state and setting menus.❹ BACK buttonTakes the display back one screen when pressed.❺ Control dialTurn to scroll through settings and press to set them.❷❶ ❹ ❺❸
6Part names and functionsRear panel❶ Antenna input jackAttach the antenna directly, or extend it with a low-loss antenna cable.❷ Unbalanced output jack (6 3 mm (1/4"))❸ Balanced output jack (XLR 3-pin male)❹ Ground lift switchThis switch isolates the GND pin of the balanced output from the ground.Normally use in the GROUND position, but if a hum develops due to a ground loop, switch to the "GROUND LIFT" side.❺ Power input jackConnect the DC plug from the included AC adapter for 12 V, 1 A.❺❸❷ ❹❶GND HOTCOLD
7Part names and functionsATW-T3201❶ Transmission antenna❷ MUTE switchPress to switch audio mute on and off.❸ IndicatorIndicates status of power supply or battery by LED.Power ON: lights in greenLow battery: lights in red • Lits once when RECALL/Multi function button is pressed and hold.❹ RECALL/Multi function buttonPress to turn the screen back on if it shuts off. Press and hold to perform the assigned action.❺ Microphone input connectorConnect a microphone (sold separately).❻ DisplayShows the current status.• If no buttons are pressed for a period of 30 seconds, the display will turn off.❼ SYNC buttonUse when syncing receiver (ATW-R3210) to the product.❽ UP buttonUsed for selecting various settings.❾ BACK buttonReturns to the previous operation.❿ Power switchTurns the power on/off.⓫ SET buttonPress to confirm a selection.⓬ DOWN buttonUsed for selecting various settings.⓭ Battery cover⓮ Technical standard conformity certification stickerUsing the product without this sticker may cause legal violation. Do not peel off.⓯ IR sync windowUse when syncing the product to the receiver.⓰ Charging terminals❶❷❸❹❺❻❼❽❾❿⓫⓭⓬⓮⓯⓰
8Part names and functionsATW-T3202❶ Grip case❷ UP buttonUsed for selecting various settings.❸ BACK buttonReturns to the previous operation.❹ IR sync windowUse when syncing the product to the receiver.❺ DOWN buttonUsed for selecting various settings.❻ SET buttonPress to confirm a selection.❼ SYNC buttonUse when syncing receiver (ATW-R3210) to the product.❽ Power switchTurns the power on/off.❾ Technical standard conformity certification stickerUsing the product without this sticker may cause legal violation. Do not peel off.❿ Battery cover⓫ RECALL/Multi function buttonPress to turn the screen back on if it shuts off. Press and hold to perform the assigned action.⓬ IndicatorIndicates status of power supply or battery by LED.Power ON: lights in greenLow battery: lights in red• Lits once when RECALL/Multi function button is pressed and hold.⓭ Charging terminals❶❷ ❸ ❹❺ ❻ ❼ ❽ ❿❾ ⓫ ⓭⓬
9Inserting batteriesATW-T32011. Slide the battery cover latches inward as shown by the arrows.2. With the latches pressed in, open the battery cover.3. Insert the batteries according to the plus (+) and minus (-) marks found inside the battery compartmentATW-T32021. Rotate the grip case.2. Open the battery cover located on the back side.3. Insert the batteries according to the plus (+) and minus (-) marks found inside the battery compartment
10Installing and removing a microphone (only for ATW-T3202)How to install1. Install the microphone to the product. 2. Rotate and tighten the microphone.How to remove1. Rotate and tighten the microphone.2. Remove the microphone from the product.
11DisplayATW-R3210❶ Key lock status (transmitter)❷ High pass filter (transmitter)❸ RF power output (transmitter)❹ Battery power indicator (transmitter)❺ RF level indicatorDisplays the reception states of antennas A & B respectively.❻ NAMEDisplays the specified name.❼ FrequencyDisplays the specified frequency.❽ Mute indicatorA mark is displayed when muted.❾ AF level indicatorDisplays the received audio signal level.❿ Group⓫ Channel⓬ Frequency Back-upDisplays when frequency back-up mode is ON.⓭ Key lock status (transmitter)❶ Antenna input jackDisplays when antenna power setting is ON.❶❷ ❸ ❹❺ ❻ ❼ ❽ ❾❿ ⓫ ⓭⓬ ⓮Transmitter information display area
12DisplayLevel meter screenSwitching screensThe screen switches each time the control dial is turned to the right / left.Main screen Level meter screen❶ RF power output (transmitter)❷ Marker (when the minimum hold function is on)The RF level is held at a minimum value.❸ Mute indicatorA mark is displayed when muted.❹ Gain indicator (transmitter)❺ Audio setting (receiver)❻ Peak hold indicator❶❷❸ ❹ ❺ ❻
13DisplayATW-T3201 / ATW-T3202The main screen is displayed when the power is switched on. Pressing the UP / DOWN button on the main screen switches the screen display.❶ FrequencyDisplays the specified frequency.❷ Key lock status❸ Battery power indicator❹ RF power output : RF Power High (30mW): RF Power Low (10mW): RF Power Off❺ High pass filterDisplays the specified name.❻ NAMEDisplays the specified name.❼ Group❽ Channel❶❷ ❷❸ ❸❸❹ ❹❹❺ ❺❻ ❼ ❽
14Basic operation1. Turn the receiver (ATW-R3210) power on.• Display lights and the main screen appears.2. Set the operating frequency.3. Turn the transmitter (ATW-T3201/ATW-T3202) power on.• The indicator lights and the main screen appears.4. Check the RF level indicator.• Check that antenna A or B lights up.5. Speak into the mic.• Make sure the AF level indicator lights up.About settingsThe various settings of this product can be made from the main menu.ATW-R32011. Press the control dial.• The main menu is displayed.2. Turn the control dial to select the item you wish to set.3. Pressing the control dial opens the settings menu of the selected item.• Press the BACK button to go back one screen.• To cancel part way through making a setting, press the BACK button.• While in the setting mode, the display will return to the main screen if 60 seconds pass without a button or the control dial being used.ATW-T3201/ATW-T32021. Press the SET button.• The main screen mode is displayed.2. Press the UP/DOWN button to select the item you wish to set.3. Pressing the SET button opens the settings menu of the selected item.• Press the BACK button to go back one screen.• To cancel part way through making a setting, press the BACK button.• While in the setting mode, the display will return to the main screen if 30 seconds pass without a button or the control dial being used.ATW-T3201 ATW-T3202ATW-T3201 ATW-T3202Selected menu item Current value
15ATW-R3201 SettingsSetting the operating frequencySetting manually1. From the main menu, turn the control dial, select [Frequency] and then press the control dial.2. Select [Manual] and then press the control dial.3. Turn the control dial and set the first 3 digits. finished setting them, press the control dial.4. Turn the control dial and set the last 3 digits. finished setting them, press the control dial.• The setting is complete.Setting by group/channel1. From the main menu, turn the control dial, select [Frequency] and then press the control dial.2. Select [Gr/Ch] and then press the control dial.3. Turn the control dial and set the group. finished setting them, press the control dial.4. Turn the control dial and set the channel. finished setting them, press the control dial.• The setting is complete.Setting NAMEThe following characters can be entered:• The maximum number of characters that can be entered is 8.• The following characters can be entered: Alphabetical characters (upper case)NumbersSymbols (+, -, #, &, period) Space1. From the main menu, turn the control dial, select [Name] and then press the control dial.2. Turn the control dial to display the character you wish to set and then press the control dial.• The character is input and the cursor moves to the right.3. Enter all the desired characters in the same way as in step (2).4. Turn the control dial to select [End] and then press the control dial.• The setting is complete.
16Setting the audio output level1. From the main menu, turn the control dial, select [Audio] and then press the control dial.2. Turn the control dial and set the audio output level.• The level changes 2dB +/- each time you turn the control dial.• It can be set from -60 to 0 dB.3. Press the control dial.• The setting is complete.Scanning for free channelScan unused channels in the surrounding area currently being used.1. From the main menu, turn the control dial, select [Group Scan] and then press the control dial.2. Turn the control dial and set the group. After selecting the group, press jet control dial.3. Turn the control dial to select the scanning sensitivity. After selecting the scanning sensitivity, press jet control dial.• The scan starts.4. Confirm the scan result, turn the control dial to select [OK] and then press the control dial.• Select [Retry] to rescan.5. Available channels and frequencies are displayed in a list. Turn the control dial to select free channels and then press the control dial.• The setting is complete.Setting transmitters via IR syncThis function allows you to make transmitter settings on the product and then automatically configure the transmitter via IR sync. Setting items and setting values are shown as follows.Item Setting valueFreq Current setting, No changeName Current setting, No changeRF Power Low:10mW, High:30mW, No changeGain -10 to +20dBm, No changeLock Lock, No changeBattery Alkaline, Ni-MH, No changeHPF OFF, ON, No change1. From the main menu, turn the control dial, select [TX Setting] and then press the control dial.2. Turn the control dial to select each item and then press the control dial.3. Turn the control dial to select the setting value and then press the control dial.4. Turn the control dial to select [Scan Start] and then press the control dial.• A standby screen is displayed. Refer to “XXX” (p. XX).
17Setting the squelch levelSetting automatically1. From the main menu, turn the control dial, select [Squelch] and then press the control dial.2. Turn the control dial to select [Auto] and then press the control dial.3. Turn the control dial to select [Normal]/[Range]/[Rubust] and then press the control dial.• The scan starts.4. The scan result is displayed. Press jet control dial.• The setting is complete.Setting manually1. From the main menu, turn the control dial, select [Squelch] and then press the control dial.2. Turn the control dial to select [Manual] and then press the control dial.3. Turn the control dial to select the value you wish to set.• The meter indicates the RF level.• You can set it from 11 dBμV 35 dBμV.4. Press jet control dial.• The setting is complete.Setting the system-related functionsSetting the key lockSet this function to prevent the product settings from being changed.• The default setting is [OFF].1. From the main menu, turn the control dial, select [System] and then press the control dial.2. Turn the control dial to select [Lock] and then press the control dial.3. Select the key lock and then press the control dial.• The setting is complete.Setting the antenna powerThis turns power on/off to the antenna input terminals• The default setting is [OFF].• If set to [ON], power is supplied to both antennas A and B.1. From the main menu, turn the control dial, select [System] and then press the control dial.2. Turn the control dial to select [ANT PWR] and then press the control dial.3. Turn the control dial to select [ON]/[OFF] and then press the control dial.• The setting is complete.
18Setting group/channel editing1. From the main menu, turn the control dial, select [System] and then press the control dial.2. Turn the control dial to select [Gr/Ch Edit] and then press the control dial.3. Turn the control dial to select the group and then press the control dial.4. Turn the control dial to select the channel and then press the control dial.5. Turn the control dial to select [SET]/[RESET] and then press the control dial.• Press [SET] to set the frequency of the selected channel.• Press [RESET] to blank the frequency of the selected channel.6. After setting all the channels, select [SET]/[Sync] and press the control dial.• When selecting [SET], the setting is complete.• When selecting [Sync], IR sync standby is displayed after the setting is complete.Setting frequency back-up1. From the main menu, turn the control dial, select [System] and then press the control dial.2. Turn the control dial to select [Back-Up Ch] and then press the control dial.3. Turn the control dial to select [ON] and then press the control dial.4. Turn the control dial to select [Manual]/[Gr/Ch] and then press the control dial.• When [Manual] is selected, the frequency can be set.• When [Gr/Ch] is selected, the group/channel can be set.5. Turn the control dial to select [SET]/[Sync] and then press the control dial.• When selecting [SET], the setting is complete.• When selecting [Sync], IR sync standby is displayed after the setting is complete.Setting main screen layout1. From the main menu, turn the control dial, select [System] and then press the control dial.2. Turn the control dial to select [Main Display] and then press the control dial.3. Turn the control dial to select [Frequency Mode]/[Name Mode]/[Gr/Ch Mode] and then press the control dial.• The setting is complete.
19Setting main screen level mater1. From the main menu, turn the control dial, select [System] and then press the control dial.2. Turn the control dial to select [AT Meter] and then press the control dial.3. Turn the control dial to select [RX]/[TX] and then press the control dial.• The setting is complete.Setting display brightness1. From the main menu, turn the control dial, select [System] and then press the control dial.2. Turn the control dial to select [Brightness] and then press the control dial.3. Turn the control dial to select [Hight]/[Low] and then press the control dial.• The setting is complete.Setting user access level1. From the main menu, turn the control dial, select [System] and then press the control dial.2. Turn the control dial to select [Access] and then press the control dial.3. Turn the control dial to select [Free Tuning]/[User Group Only] and then press the control dial.• The setting is complete.Resetting factory defaultsThis returns the settings to their factory defaults.1. From the main menu, turn the control dial, select [System] and then press the control dial.2. Turn the control dial to select [Reset] and then press the control dial.3. Turn the control dial to select [Yes] and then press the control dial.4. After the confirmation screen is displayed, turn the control dial again to select [Yes] and press the control dial.• Reset starts.Checking the product informationThis function displays product information.1. From the main menu, turn the control dial, select [System] and then press the control dial.2. Turn the control dial to select [Version] and then press the control dial.
20ATW-T3201/ATW-T3202 settingsSetting the transmission frequency1. From the main menu, press the UP/DOWN button to select [FREQUENCY] and then press the SET button.2. Select [MANUAL] and press the SET button.3. Press the UP/DOWN button and set the first 3 digits. After completing the setting, press the SET button.4. Press the UP/DOWN button and set the last 3 digits. After completing the setting, press the SET button.• The setting is complete.Setting group/channel1. From the main menu, press the UP/DOWN button to select [FREQUENCY] and then press the SET button.2. Select [Gr/Ch] and press the SET button.3. Press the UP/DOWN button and set the group. After completing the setting, press the SET button.4. Press the UP/DOWN button and set the channel. After completing the setting, press the SET button.• The setting is complete.Setting NAMEThe following characters can be entered:• The maximum number of characters that can be entered is 8.• The following characters can be entered: Alphabetical characters (upper case)NumbersSymbols (+, -, #, &, period) Space1. From the main menu, press the UP/DOWN button to select [NAME] and then press the SET button.2. Press the UP/DOWN button to select the character you want to set and then press the SET button.• The character is input and the cursor moves to the right.3. Enter all the desired characters in the same way as in step (2).• If you do not enter 8 characters, press the UP / DOWN button, select [End], and press the SET button4. At the 8th character, press the SET button.• [End] is displayed.5. Press the SET button.• The setting is complete.Setting gain1. From the main menu, press the UP/DOWN button to select [GAIN] and then press the SET button.2. Press the UP/DOWN button and set the gain.• The level changes 2 dB +/- each time you press the UP/DOWN button.3. Press the SET button.• The setting is complete.
21Setting RF output 1. From the main menu, press the UP/DOWN button to select [RF POWER] and then press the SET button.2. Press the UP/DOWN button and select RF output as [Low: 10 mW]/[High: 30 mW]/[OFF].3. Press the SET button.• The setting is complete.Setting HPF (High Pass Filter)1. From the main menu, press the UP/DOWN button to select [HPF] and then press the SET button.2. Press the UP/DOWN button to select [ON]/[OFF].3. Press the SET button.• The setting is complete.Setting key lock1. From the main menu, press the UP/DOWN button to select [LOCK] and then press the SET button.2. Press the UP/DOWN button to select [Lock]/[Unlock].Lock Keys lockedUnlock Keys unlocked3. Press the SET button.• The setting is complete.Setting button modeThe function is assigned when RECALL/Multi function button is pressed and hold.1. From the main menu, press the UP/DOWN button to select [BUTTON MODE] and then press the SET button.2. Press the UP/DOWN button to select the item you wish to set.Disable No functionNormal Mute (only for ATW-T3202)MutedForced Mute (only for ATW-T3202)Mute in on when key is locked.BKUP CH Frequency backup mode (When selected, frequency, group, and channel are set.)RF Off RF output is OFF.3. Press the SET button.• The setting is complete.Setting mute mode (only for ATW-T3201)Set the MUTE switch function.1. From the main menu, press the UP/DOWN button to select [MUTE MODE] and then press the SET button.2. Press the UP/DOWN button to select the item you wish to set.Normal Mute MutedForced Mute Mute in on when key is locked.Disable No function3. Press the SET button.• The setting is complete.
22Setting the system-related functionsSetting batterySet the type of batteries used.1. From the main menu, press the UP/DOWN button to select [System] and then press the SET button.2. Press the UP/DOWN button to select [BATTERY] and then press the SET button.3. Press the UP/DOWN button to select battery type.Alkaline Select for alkaline batteriesNi-MH Select for nickel–metal hydride batteries4. Press the SET button.• The setting is complete.• If the appropriate setting is not made for the batteries used, the battery power indicator does not display the correct information. Always set the type of battery according to the batteries used.Setting LED1. From the main menu, press the UP/DOWN button to select [System] and then press the SET button.2. Press the UP/DOWN button to select [LED] and then press the SET button.3. Press the UP/DOWN button to select [ON]/[OFF].4. Press the SET button.• The setting is complete.Setting user access level1. From the main menu, press the UP/DOWN button to select [System] and then press the SET button.2. Press the UP/DOWN button to select [ACCESS] and then press the SET button.3. Press the UP/DOWN button to select [Free]/[User Group].4. Press the SET button.• The setting is complete.Resetting factory defaultsThis returns the settings to their factory defaults.1. From the main menu, press the UP/DOWN button to select [System] and then press the SET button.2. Press the UP/DOWN button to select [RESET] and then press the SET button.3. Press the UP/DOWN button to select [Yes].4. After the confirmation screen is displayed, press the UP/DOWN button again to select [Yes].5. Press the SET button.• Reset starts.Checking the product versionThis function displays product version.1. From the main menu, press the UP/DOWN button to select [System] and then press the SET button.2. Press the UP/DOWN button to select [VERSION] and then press the SET button.• The version is displayed.
23Attaching the product to user's body (ATW-T3201)The product is equipped with a clip. Use that to attach the product to a belt, pocket or other piece of clothing that will hold it.You can reverse the direction that the input connector faces by attaching the clip in the opposite direction.Pull both sides of the clip firmly to the outside to remove the clip from the product.Making connections (basic connections)This example is of connections made when using one ATW-R3201.When connecting more than one ATW-R3201 via a distributor (sold separately), refer to the distributor's user manual.Antenna AntennaPower cableMixer IN

Navigation menu