Audiovox Prestige P 950W Users Manual 1286267
Prestige P-950W d088804d-2fb2-4934-aa4a-b5c7ba8298ab
P-950W to the manual d088804d-2fb2-4934-aa4a-b5c7ba8298ab
2015-02-02
: Audiovox Audiovox-Prestige-P-950W-Users-Manual-401041 audiovox-prestige-p-950w-users-manual-401041 audiovox pdf
Open the PDF directly: View PDF .
Page Count: 6
Download | ![]() |
Open PDF In Browser | View PDF |
INSTALLATION MANUAL OPEN P-950W CD-R/RW PLAYBACK Sub. W CLAS POP EQ Tune /Seek JAZZ LOC T/F REG AF TA MONO MULTI-COLOR FLOURESCENT DISPLAY SEL SCAN AS/PS PTY ME/CR LOUD MUTE MONO /Track EON TP ST ILL PWR POWER LEVEL METER LOC 1 PAU 2 SCN 3 RPT 4 SHF 5 D.DN 6 D.UP P-950W AM/FM/MPX RADIO WITH FOLD-DOWN DETACHABLE FRONT PANEL, COMPACT DISC PLAYER, CD CHANGER CONTROLS, WIRELESS REMOTE CONTROL AND QUARTZ CLOCK MODE BAND LOUD INSTALLATION INSTRUCTIONS This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialist shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but cannot find it available, call our toll-free “HELP” line at 1-800-645-4994. UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE 1. Open, fold down and remove the detachable front panel, if it is attached to the chassis, by grasping the grooved center portion and pulling the panel assembly straight out. Slide the mounting sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it. 2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis. 3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard. 4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections of the wiring harness are secure and insulated with wire nuts or electrical tape to insure proper operation of the unit. After completing the wiring connections, attach the front panel and turn the unit on to confirm operation (ignition switch must be“on”). If unit does not operate, re-check all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis. 5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place. 6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary. CAUTION: 7. The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration. Re-attach the front panel to the chassis and test radio operation by referring to the Operating Instructions for the unit. INSTALLATION USING KITS 1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit. 2. Wire and test the radio as described in Step 4 above. 3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit. 4. Attach the support strap to the radio and dashboard as described in Step 6 above. 5. Replace the dashboard trim panel. ISO INSTALLATION PROCEDURE This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialist shop for assistance on this type of installation. 1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio. 2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame. 3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio. CAUTION: DO NOT EXCEED M5 X 5 MM MAXIMUM SCREW SIZE. LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS. 4. Wire the new radio to the vehicle as per step 4 above. 5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1. -2- TOLL-FREE INSTALLATION ASSISTANCE The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do, we're here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and hours shown (U.S.A. and Canada only). TIME ZONE DAY PACIFIC MON. - FRI. SATURDAY MOUNTAIN 5:30AM - 4PM 6AM - 2PM CENTRAL EASTERN 8:30AM - 7PM 9AM - 5PM 7:30AM - 6PM 8AM - 4PM 6:30AM - 5PM 7AM - 3PM UNIVERSAL INSTALLATION USING MOUNTING SLEEVE NUT (5MM) PERFORATED STRAP FASTEN THIS END TO SCREW STUD ON REAR OF CHASSIS EXISTING DASH OPENING FILE EDGES TO FIT IF NECESSARY - DO NOT OVERFILE NOTE: IF DASH IS SOLID, USE REAR SIDE (WITHOUT THE LIP) OF MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING BEND TOP TABS UPWARD SCREW (5MM) BEND BOTTOM TABS DOWNWARD RADIO SCREW STUD NUT (5MM) MOUNTING SLEEVE FASTEN THIS END TO SECURE PART OF DASHBOARD. DRILL HOLE IF NECESSARY. REMOVAL TOOLS CAUTION: FOR PROPER OPERATION OF THE CD PLAYER, THE CHASSIS MUST BE MOUNTED WITHIN 20° OF HORIZONTAL. MAKE SURE THE UNIT IS MOUNTED WITHIN THIS LIMITATION. FOLD-DOWN DETACHABLE FRONT PANEL 20° MAX. SIDE VIEW OF CHASSIS FRONT PANEL ISO INSTALLATION TYPICAL INSTALLATION REMOVE THE PLASTIC FRAME FROM THE FRONT OF THE CHASSIS BY CAREFULLY UN-SNAPPING IT. MAXIMUM SCREW SIZE M5 x 5MM UN-SNAP AT 2 PLACES EACH ON TOP AND BOTTOM PLASTIC FRAME FACTORY MOUNTING BRACKETS -3- MAXIMUM SCREW SIZE M5 x 5MM RADIO WIRING REFER TO PAGE 5 FOR SPEAKER WIRING AUTOMATIC ANTENNA ANTENNA BLUE IMPORTANT THE BLUE WIRE CAN BE USED TO REMOTELY ACTIVATE AN AUTOMATIC ANTENNA OR AN EXTERNAL AMPLIFIER (SEE ANTENNA OR AMPLIFIER MANUAL) FUSEBLOCK EXISTING ANTENNA CABLE “RADIO” FUSE +12V ACCESSORY RED 0.5 AMP. FUSE SCREW BLACK METAL PART OF DASH (DRILL HOLE IF NECESSARY) CAR BATTERY YELLOW 15 AMP. FUSE IMPORTANT YELLOW WIRE MUST BE CONNECTED AS SHOWN OR RADIO WILL NOT OPERATE PROPERLY POSITIVE (+) TERMINAL 12 VOLT BATTERY 4-PIN PLUGS 9 PIN PLUG (SEE PAGE 5 FOR SPEAKER WIRING) ANTENNA LEAD ON REAR OF RADIO EXTERNAL INVERTER FOR VFD DISPLAY BACKLIGHTING AUXILIARY INPUT JACK (MOUNT UNDER DASH IN A CONVENIENT LOCATION) -4- SPEAKER WIRING REFER TO PAGE 4 FOR RADIO WIRING WARNING! l THE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS. l NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS. l NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND. l FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL NOTE: THIS RADIO WILL CONTROL PRESTIGE CD CHANGER MODEL SP-11CDP. CHECK WITH YOUR PRESTIGE AUDIOVOX CAR STEREO SPECIALIST OR CALL 1-800-645-4994 FOR RECOMMENDATIONS OF OTHER MODELS THAT WILL WORK WITH YOUR RADIO. RCA LINE JACKS FOR USE WITH OPTIONAL EXTERNAL AMPLIFIERS OPTIONAL CD CHANGER 2CH LINE IN 4CH LINE OUT RADIO DIN CABLE (SUPPLIED WITH CD CHANGER). 6 C OMP AC T 8-PIN DIN SOCKET FOR CONNECTION TO OPTIONAL CD CHANGER LINE IN/ OUT (LEFT) = WHITE LINE IN.OUT OUT (RIGHT) = RED 4-PIN PLUGS 9-PIN PLUGS LEFT FRONT SPEAKER SEE PAGE 4 FOR RADIO WIRING RIGHT FRONT SPEAKER GRAY w/BLACK STRIPE WHITE w/BLACK STRIPE WHITE GRAY GREEN VIOLET GREEN w/BLACK STRIPE VIOLET w/BLACK STRIPE HELP! 1-800-645-4994 8:30am - 7:00pm Eastern 9:00am - 5:00pm Eastern Monday - Friday Saturday LEFT REAR SPEAKER RIGHT REAR SPEAKER -5- © 2002 AUDIOVOX ELECTRONICS CORP., HAUPPAUGE, NY Printed in China 128-6267
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2002:05:21 13:37:23-04:00 Modify Date : 2002:05:21 13:37:23-04:00 Subject : 1286267 Page Count : 6 Creation Date : 2002:05:21 17:37:23Z Mod Date : 2002:05:21 17:37:23Z Producer : Acrobat Distiller 5.0 (Windows) Author : LCURATOL Keywords : Metadata Date : 2002:05:21 17:37:23Z Creator : LCURATOL Title : 1286267 Description : 1286267EXIF Metadata provided by EXIF.tools