Audiovox Prestige P 950W Users Manual 1286267

Prestige P-950W d088804d-2fb2-4934-aa4a-b5c7ba8298ab

P-950W to the manual d088804d-2fb2-4934-aa4a-b5c7ba8298ab

: Audiovox Audiovox-Prestige-P-950W-Users-Manual-401041 audiovox-prestige-p-950w-users-manual-401041 audiovox pdf

Open the PDF directly: View PDF .
Page Count: 6

P-950W

AM/FM/MPX RADIO

WITH FOLD-DOWN

DETACHABLE FRONT PANEL,

COMPACT DISC PLAYER,

CD CHANGER CONTROLS,

WIRELESS REMOTE CONTROL

AND QUARTZ CLOCK

INSTALLATION MANUAL

T/F

EQ

LOCSCANMUTE

SEL

1

OPEN

JAZZ

MONO

ST

LOC

REG

LOUD

POP

CLAS

CD-R/RW PLAYBACK

POWER LEVEL METER

2

PAU SCN RPT

3

SHF

4 5

D.DN D.UP

6

MODE

P-950W

ME/CR

TP

AF TA EON

PTY

Sub. W

/Seek

/Track

Tune

ILL

PWR

MONO

BAND

AS/PS

LOUD

MULTI-COLOR FLOURESCENT DISPLAY

-2-

INSTALLATION INSTRUCTIONS

This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special installation

kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo

specialist shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but

cannot find it available, call our toll-free “HELP” line at 1-800-645-4994.

UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE

1. Open, fold down and remove the detachable front panel, if it is attached to the chassis, by grasping the grooved center

portion and pulling the panel assembly straight out. Slide the mounting sleeve off of the chassis. If it is locked into position,

use the removal tools (supplied) to disengage it.

2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or

file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend

or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.

3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted

into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to

the dashboard.

4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting sleeve. Follow

the wiring diagram carefully and make certain all connections of the wiring harness are secure and insulated with wire

nuts or electrical tape to insure proper operation of the unit. After completing the wiring connections, attach the front panel

and turn the unit on to confirm operation (ignition switch must be“on”). If unit does not operate, re-check all wiring until

problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting

of the chassis.

5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated

and the spring clips lock it into place.

6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex

nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below

the radio using the screw and hex nut provided. Bend the strap to position it as necessary.

CAUTION: The rear of the radio must be supported with the strap to prevent damage to the

dashboard from the weight of the radio or improper operation due to vibration.

7. Re-attach the front panel to the chassis and test radio operation by referring to the Operating Instructions for the

unit.

INSTALLATION USING KITS

1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the

installation kit to attach the radio to the mounting plate supplied with the kit.

2. Wire and test the radio as described in Step 4 above.

3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.

4. Attach the support strap to the radio and dashboard as described in Step 6 above.

5. Replace the dashboard trim panel.

ISO INSTALLATION PROCEDURE

This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some

Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your

local car stereo specialist shop for assistance on this type of installation.

1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and brackets

as they will be used to mount the new radio.

2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame.

3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.

CAUTION: DO NOT EXCEED M5 X 5 MM MAXIMUM SCREW SIZE. LONGER SCREWS

MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS.

4. Wire the new radio to the vehicle as per step 4 above.

5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.

-3-

8:30AM - 7PM

9AM - 5PM

CENTRAL EASTERN

6:30AM - 5PM

7AM - 3PM

MOUNTAIN

5:30AM - 4PM

6AM - 2PM

PACIFIC

MON. - FRI.

SATURDAY

DAY

TIME ZONE

TOLL-FREE INSTALLATION ASSISTANCETOLL-FREE INSTALLATION ASSISTANCE

TOLL-FREE INSTALLATION ASSISTANCETOLL-FREE INSTALLATION ASSISTANCE

TOLL-FREE INSTALLATION ASSISTANCE

The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do, we're here to help you. Just call

our toll-free telephone assistance line at 1-800-645-4994 during the days and hours shown (U.S.A. and Canada only).

7:30AM - 6PM

8AM - 4PM

FASTEN THIS END TO SCREW STUD ON

REAR OF CHASSIS

NUT (5MM)

FASTEN THIS END TO SECURE PART OF DASHBOARD.

DRILL HOLE IF NECESSARY.

SCREW (5MM)

FOLD-DOWN

DETACHABLE

FRONT PANEL

EXISTING DASH OPENING

FILE EDGES TO FIT IF NECESSARY - DO NOT OVERFILE

NOTE: IF DASH IS SOLID, USE REAR SIDE (WITHOUT THE LIP) OF MOUNTING SLEEVE

AS A TEMPLATE & CUT OPENING

UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE

UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE

UNIVERSAL INSTALLATION USING MOUNTING SLEEVE

NUT (5MM)

REMOVE THE PLASTIC FRAME FROM THE FRONT OF THE CHASSIS BY

CAREFULLY UN-SNAPPING IT.

ISO INSTALLATIONISO INSTALLATION

ISO INSTALLATIONISO INSTALLATION

ISO INSTALLATION

20° MAX.

FRONT PANEL

CAUTION:

FOR PROPER OPERATION OF THE CD PLAYER, THE CHASSIS MUST BE MOUNTED

WITHIN 20° OF HORIZONTAL. MAKE SURE THE UNIT IS MOUNTED WITHIN THIS

LIMITATION.

SIDE VIEW

OF

CHASSIS

UN-SNAP AT 2 PLACES EACH ON

TOP AND BOTTOM

MAXIMUM SCREW

SIZE

M5 x 5MM MAXIMUM SCREW

SIZE

M5 x 5MM

PERFORATED STRAP

RADIO

SCREW STUD

MOUNTING SLEEVE

PLASTIC FRAME

FACTORY MOUNTING

BRACKETS

REMOVAL TOOLS

BEND BOTTOM TABS

DOWNWARD

BEND TOP

TABS UPWARD

TYPICAL INSTALLATION

-4-

CAR BATTERY

RADIO WIRINGRADIO WIRING

RADIO WIRINGRADIO WIRING

RADIO WIRING

REFER TO PAGE 5 FOR SPEAKER WIRING

IMPORTANT

THE BLUE WIRE CAN BE USED TO REMOTELY ACTI-

VATE AN AUTOMATIC ANTENNA OR AN EXTERNAL

AMPLIFIER (SEE ANTENNA OR AMPLIFIER MANUAL)

ANTENNA LEAD

ON REAR OF RADIO

9 PIN PLUG

(SEE PAGE 5 FOR SPEAKER WIRING)

POSITIVE (+) TERMINAL 12 VOLT

BATTERY

METAL PART OF DASH

(DRILL HOLE IF NECESSARY)

SCREW

BLACK

EXISTING

ANTENNA

CABLE

BLUE

ANTENNA AUTOMATIC

ANTENNA

FUSEBLOCK

IMPORTANT

YELLOW WIRE MUST BE CONNECTED

AS SHOWN OR RADIO WILL NOT OP-

ERATE PROPERLY

4-PIN PLUGS

“RADIO” FUSE

+12V ACCESSORY

EXTERNAL INVERTER FOR

VFD DISPLAY BACKLIGHTING

AUXILIARY INPUT JACK

(MOUNT UNDER DASH IN

A CONVENIENT LOCATION)

RED 0.5 AMP. FUSE

YELLOW 15 AMP. FUSE

-5-

SPEAKER WIRINGSPEAKER WIRING

SPEAKER WIRINGSPEAKER WIRING

SPEAKER WIRING

REFER TO PAGE 4

FOR RADIO WIRING

WARNING!

lTHE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS.

lNEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS.

lNEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND.

lFAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL

WHITE w/BLACK STRIPE

WHITE

LEFT FRONT SPEAKER RIGHT FRONT SPEAKER

LEFT REAR SPEAKER RIGHT REAR SPEAKER

GREEN

GRAY w/BLACK STRIPE

9-PIN PLUGS

GREEN w/BLACK STRIPE VIOLET w/BLACK STRIPE

RADIO

GRAY

VIOLET

4-PIN PLUGS

SEE PAGE 4 FOR RADIO

WIRING

8-PIN DIN SOCKET FOR CONNECTION TO OPTIONAL CD

CHANGER

6

COMPACT

DIN CABLE (SUPPLIED

WITH CD CHANGER).

OPTIONAL

CD CHANGER

NOTE: THIS RADIO WILL CONTROL PRESTIGE CD CHANGER

MODEL SP-11CDP. CHECK WITH YOUR PRESTIGE AUDIOVOX CAR

STEREO SPECIALIST OR CALL 1-800-645-4994 FOR RECOMMENDA-

TIONS OF OTHER MODELS THAT WILL WORK WITH YOUR RADIO.

RCA LINE JACKS

FOR USE WITH

OPTIONAL EXTERNAL

AMPLIFIERS

2CH LINE IN 4CH LINE OUT

LINE IN/ OUT (LEFT) = WHITE

LINE IN.OUT OUT (RIGHT) = RED

8:30am - 7:00pm Eastern

9:00am - 5:00pm Eastern

1-800-645-49941-800-645-4994

1-800-645-49941-800-645-4994

1-800-645-4994

Monday - Friday

Saturday

HELP!

© 2002 AUDIOVOX ELECTRONICS CORP., HAUPPAUGE, NY Printed in China

128-6267