Aurum Electronics AEC711C Wireless Handheld Screen Receiver User Manual AEC 711C IM EU
Aurum Electronics Corp. Wireless Handheld Screen Receiver AEC 711C IM EU
User Manual
AEC-711C Wireless Handheld Screen Receiver I. OVERVIEW OF AEC-711C Antenna Holder LCD LED indicator LCD/TV Button Power switch MENU Button OK Button Video Output Battery case Channel Button View Button (1/4) (Single/Quad) Buzzer Power Socket II. ASSEMBLY INSTRUCTION 1. Install 3pcs NI-MH rechargeable batteries to the battery compartment with its polarities matched. Note: - This receiver can also be powered on by adapter (DC 6V 1.5A). - The rechargeable battery will be charged after the adapter is plugged in, and the charge indicator lights up during charging and will turn off after a full charge. - A full charge will take about 6 hours, which can power the receiver for about 4 hours continuously. - You are recommended to have the battery fully charged before its first installation to optimize its life. - Do not burn or disassemble the rechargeable battery. - Do not short-circuit the battery, it may cause fire or electric shock. 2. Push the power switch to ON position. Rechargeable battery (inside) 3 . Set the channel of receiver same as that of fitting by pressing the channel button continuously, and the pictures are displayed on the monitor/TV. - Press “MENU Button” then press Channel Button to select “MONITOR” and press “OK button”. - Press “Channel Button” to select ”Pair Cam” and then press “OK button”. - There is ”1 2 3 4” shown on the LCD, to select which number of channel you want to set up this fitting. Within 10 seconds, press “Channel Button” to select the number of the channel you want then press ”OK button”. Within 10 seconds, press the “Dip Switch” on the fitting and when you see detecting image displayed on the LCD, it means the channel setting is completed. If it shows “No Connection”, repeat these steps again. - For other three different fittings, repeat the above same steps to set up the different channel. Press ”View Button” for Quad View condition, you can see 4-split view from 4 different fittings. NOTE: 1. When you make the channel setting, LCD must be under “Single View” condition. 2. Before setting the channel between the fitting and LCD, press “Push-button” switch on the bottom of the fitting firstly, the stepper motor will stop working (the RED LED will keep flashing) in order to keep “Dip Switch” on the fitting not moving and can be easily pressed when setting up the channel later. 4. For more clear pictures or record image: 1 Please connect the receiver to a TV with video cable. ○ 2 Please connect the receiver to a TV and a video recorder with video cable. ○ ○ ○ LCD/TV Button III. OPERATION When AEC-9331C detects any movement, wireless LCD monitor is triggered for 30/60 seconds image at the same time. The unobstructed transmission effective range is about 80 meters, but actual transmission range may vary according to weather, location, interference and building. One wireless LCD monitor is possible to receiver 4 camera image. IMPORTANT OPERATION OF WIRELESS HANDHELD SCREEN RECEIVER 1. LCD image display: push view button「1/4」for image display -Single View: single CAMERA view (initial image) display image from one camera at one time This is only for connecting 1 CAMERA. For connecting several CAMERAS, make sure to return to quad-view after finishing setting in single view. -Quad View : 4 split view (able to connect 4 CAMERAS and display 4 images on screen at the same time) ☆When SENSOR is triggered, the monitor will sound ”BEEP” (“BEEP” is set “ON” condition) No. 1 sensor light detects motions, sound ”BEEP” once No. 2 sensor light detects motions , sound ”BEEP-BEEP” twice No. 3 sensor light detects motions, sound ”BEEP-BEEP-BEEP”3 times No. 4 sensor light detects motions, sound ”BEEP-BEEP-BEEP-BEEP” 4 times ☆BEEP will sound continuously for 20 times and stops if there is no further detection. During 20 times of BEEP if this unit detects any motions, it will recount for 20 times. ☆ Push any of the buttons to stop ”BEEP”. ☆When BEEP is set“OFF”, there will be no sound. ☆「View Mode」is set ”MENU”(manual) , the number of camera will flash under quad-view. 2. Function settings:push “MENU “ button to choose settings. -CAMERA: Set the brightness of CAMERA. Standard value is 0, turn the knob to ”-“ side to reduce the brightness, turn the knob to ”+”side to increase the brightness. Before attempting any setting, please power sensor light. For multiple cameras, the brightness of each CAMERA may be different, please adjust the brightness to preferred value. (Every adjustment value is 0.5. Original default is 0.) Freq:50 / 60 Hz Version:software program version Back to original default. Reset:Yes/No Cam1 EV:-2.0~+2.0 Cam2 EV:-2.0~+2.0 Cam3 EV:-2.0~+2.0 Cam4 EV:-2.0~+2.0 -MONITOR: Beep:ON/OFF(original default ON) Beep Vol:High/Low(original default High) Brightness:0~10( original default 5) OSD Disp:ON/OFF View Mode:AUTO/MENU( original default AUTO) When SENSOR detects motions, monitor will beep. Volume adjustment for beep LCD brightness adjustment Date and antenna icon display set Single view and quad-view setting (AUTO/MENU): Under AUTO mode, single view will return to quad-view automatically 20 seconds later;under MENU mode, please switch from single view to quad-view by manual. Under MENU mode, if switch to single view, there will no display on the screen if other sensor lights detect motions. Looping function, 4 CAMERAS display single view on the screen in order. Register CAMERA ID。(up to 4 CAMERAS) Scan time:OFF/5SEC/10SEC/15SEC (original default OFF) Pair Cam:1/2/3/4 IMPORTANT Before registering ID, please push the bottom button to stop sensor light turning. Version:software program version Reset:YES/NO Back to original default. -Other:Date/Time:set time and date CHARGE When connect Wireless Handheld Screen Receiver to AC ADAPTER, it will charge batteries automatically. Under charge, LED turns red color. IMPORTANT Charge time:6 hours max. Red LED:charge DO NOT USE PRIMARY BATTERY ! Red LED flashes:abnormal charge Such as Manganese electric ※Under abnormal charge, please remove AC ADAPTER and check if battery 、Alkaline electric battery batteries are placed correctly. and oxy ride electric battery to prevent hazard like leakage and LED indicator crack. REPLACE BATTERIES Battery used:AA NI-MH 2600mAh rechargeable battery 3PCS 1. Take old batteries out. 2. Place new batteries into battery case see right side figure -Make sure the polarity is aligned correctly - Please replace 3 batteries together FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Format : application/pdf Creator : joanne Title : Microsoft Word - AEC-711C IM - EU.doc Create Date : 2010:05:06 10:43:57+08:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2010:07:05 13:10:20+08:00 Metadata Date : 2010:07:05 13:10:20+08:00 Producer : Acrobat Distiller 8.0.0 (Windows) Document ID : uuid:b6658314-fb85-40d0-a40d-84c407f93df9 Instance ID : uuid:341247ec-d912-4db3-9702-8e69cb4855dc Has XFA : No Page Count : 4 Author : joanneEXIF Metadata provided by EXIF.tools