Autec s r l FJRNZ422 Transceiver unit User Manual

Autec s.r.l. Transceiver unit

User Manual

Original instructionsDYNAMIC SERIESPart B:Conformity and frequencies(915MHz - FCC/IC)INDEX1 Conformity ............................................................................................................. 21.1 Federal Communications Commission (FCC) ................................................... 31.2 Industry Canada (IC) ........................................................................................ 32 Frequencies ........................................................................................................... 32.1 Dynamic mode ................................................................................................. 32.2 Static mode ...................................................................................................... 33 Market .................................................................................................................... 4AUTEC LIDY2E00-08
2LIDY2E00-08ConformityAUTEC - Dynamic Series1 ConformityEach Dynamic series' radio remote control working in the frequency band 915-928MHz complies with Part 15 of standards FCC and with RSS-210 of IC standards.Unit FCC ID IC numberADD OQA-ADDNE022 d9061A-ADDNE022 a b cARM OQA-ARMNB022 dOQA-ARMNC022 d9061A-ARMNB022 a b c9061A-ARMNC022 a b cARS OQA-ARSND022 d9061A-ARSND022 a b cARX OQA-ARXNG022 d9061A-ARXNG022 a b cCRS OQA-CRSNA022 d9061A-CRSNA022 a b cCRX OQA-CRXNH022 d9061A-CRXNH022 a b cFJL OQA-FJLNF022 9061A-FJLNF022FJM OQA-FJMNF022 9061A-FJMNF022FJM OQA-FJMNZ422 9061A-FJMNZ422FJR OQA-FJRNF022 9061A-FJRNF022FJR OQA-FJRNZ422 9061A-FJRNZ422FJS OQA-FJSNF022 9061A-FJSNF022a. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.b. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Antenna type Antenna gain Antenna impedanceAutec stylus λ/4 <2dBi 50 OhmAutec stylus λ/4 with 5m RG58 <2dBi 50 Ohmc. Autec allows you to use only the dedicated antenna supplied either with the remote control or as original spare part. The use of any other type of antenna is prohibited and will invalidate the guarantee.d. Place the antenna of the receiving unit in a position that ensures a minimum separation distance of 20cm with all the people that can be in the working area.
AUTEC - Dynamic SeriesFrequencies 3LIDY2E00-081.1 Federal Communications Commission (FCC)This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.1.2 Industry Canada (IC)This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.2 FrequenciesThe radio link between the units of Autec Dynamic series radio remote controls is established at one of the frequencies permitted by the US, Canadian and Australian standards in force when the system is put on the market.Frequency band ............................................................................................ 915-928MHzRF power ........................................................................ meets FCC and IC requirementsAvailable radio channels .............................................................................................. 259Channel spacing ...................................................................................................... 50kHzDynamic series industrial radio remote controls communicate either in dynamic or static mode. Mode is set by the machine manufacturer.2.1 Dynamic modeA radio remote control communicating in dynamic mode: -uses a working frequency in the band 915-928MHz -checks that the frequency is free before using it -continually changes the working frequency to maintain the radio link even when interference occurs.2.2 Static modeA radio remote control communicating in static mode: -uses a working frequency in the band 915-928MHz -checks that the frequency is free before using it -always works at the same frequency until the stop function is activated.
4LIDY2E00-08MarketAUTEC - Dynamic Series3 MarketDynamic series' radio remote controls working in the frequency band 915-928MHz can be used in the US, Canadian and Australian markets.

Navigation menu