Authinx CR14A Pan n' Tilt Remote User Manual Exhibit D Users Manual per 2 1033 b3

Authinx Inc. Pan n' Tilt Remote Exhibit D Users Manual per 2 1033 b3

Exhibit D Users Manual per 2 1033 b3

To clear all stored positions: Press and hold Center then flipthe switch at the bottom to Program and back.Pan ‘n Tilt Remote For use with X10 wireless camerasModel CM14ACM14A-8/011. Install 4 AAA alkaline batteries (sold separately) in theremote’s battery compartment.2. Use a dime to set the Housecode dial to match the cameras,and transceiver you want to use the remote with.3. Plug in an X10 Transceiver (RR501 or TM751, sold separately).Set Housecode to match remote. Fully extend the antenna.4. To control up to 4 Cameras, attach each one to a ZC15A Panand Tilt base (sold separately), plug each ZC15A into its ownAddressable Power Supply, and set each power supply tothe same Housecode you used in steps 2 and 3. Set eachpower supply to a unique number between 1 and 4. Pressingany Camera button (C1, C2, C3, or C4) turns on that camera (1,2, 3, or 4) and turns the others (in the group) off. Then, eachpress of either the or button turns on the next orprevious camera in the group of 4 while turning the currentcamera off. (You set all cameras to the same channel as theVideo Receiver connected to your TV (Channel A, B, C, D).5. After you press the "C" button to turn on a camera, pressinga left or right BLUE button at the top “pans” the camera left orright. Pressing a BLUE up or down button “tilts” the cameraup or down.6. To make buttons C1 thru C4 control cameras 5-8 (instead of 1thru 4) press (and hold) the C2 button then flip the switch atthe bottom from Normal to Program and back. Buttons C1, C2,C3, and C4 now control cameras set to 5, 6, 7, and 8.7. Pressing C3 in step 6 sets buttons C1, C2, C3, and C4 tocontrol cameras set to 9, 10, 11, and 12.8. Pressing C4 in step 6 sets buttons C1, C2, C3, and C4 tocontrol cameras set to 13, 14, 15, and 16.Buttons P1 thru P4 are used to store 4 position settings foreach of the 4 cameras controlled by buttons C1 thru C4.1. To store the first position for the camera controlled by C1,press C1.2. Press the blue buttons to scan to the position you want.3. Press and hold P1, then flip the switch at the bottom fromNormal to Program and back, to store that position under P1.4. Repeat steps 2 and 3, pressing P2 to store another positionunder P2.5. Repeat for P3, and P4.Repeat steps 1 thru 4 to store 4 positions for C2, C3, and C4.Press the “C” button for any camera, following by any “P”button to move to the position stored under that button forthat camera.Press the “C” button then Sweep to sweep through all 4positions stored for that camera.Press the “C” button then Center to center the position forthat camera.Installation and operating instructionsThe CR14A Remote lets you turn on any of 4 cameras or scan each of them in turn (forward or backward) so as to display the image fromeach camera in turn on your TV. If you purchase a Camera Pan and Tilt base (model ZC15A) for each camera, you can also use the remoteto move the position of the camera from left to right (Pan) and up and down (Tilt). The Remote sends Wireless Radio Frequency (RF)signals to an X10 Transceiver (RR501 or TM751). The Transceiver then passes the signals onto your house wiring to control WirelessCameras around your home. You connect each camera (up to 4) to a ZC15A base and plug each ZC15A into Addressable Power Supplieseach set to a different number. The CR14A normally controls Cameras set to Unit Codes 1, 2, 3, 4. But you can set it to control cameras setto 5, 6, 7, 8, or 9, 10, 11, 12, or 13, 14, 15, 16.ProgramSCANSweepCentreNormalACEGIKMO........CAMERAC1C3C2C4POSITIONP1 P2P4P3Set to the same letter asthe TM751 and cameras. Scans forward or backwardthru cameras controlled byC1 thru C4.“Pans” leftand right.“Tilts” upand down.Writelocationsof camerashere. Controls 4cameras.Stores thepositionsfor 4cameras.F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15OF THE FCC RULES. OPERATION IS SUBJECT TO THEFOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAYNOT CAUSE HARMFUL INTERFERENCE, AND (2) THISDEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,INCLUDING INTERFERENCE THAT MAY CAUSEUNDESIRED OPERATION.NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADETO THE UNITS. ANY CHANGES MADE TO THE UNITSWILL VOID THE USER'S AUTHORITY TO OPERATE THEEQUIPMENT.LIMITED 1-YEAR WARRANTYPlease visit www.x10.com/warrantyto complete your on-line warranty registration. Thank you.For help or more information on setup, please visit:www.x10.com/supportCenterseachcameraposition.Sweepsthru the 4storedpositionsfor theselectedcamera.

Navigation menu