Authinx JSC13A SUPERVISED SECURITY SYSTEM User Manual Jasco JSC1300 OM pmd

Download:
Mirror Download [FCC.gov]
Document ID	600020
Application ID	vk1U8aVaah/RN9quLOhKng==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	70.96kB (886965 bits)
Date Submitted	2005-11-07 00:00:00
Date Available	2005-11-07 00:00:00
Creation Date	2005-11-04 23:42:04
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2005-11-04 19:26:10
Document Title	Jasco JSC1300-OM.pmd
Document Creator	PageMaker 7.0
Document Author:	Dave Rye

Owner’s Manual
Supervised Security System
Model JSC1300
ARM
DISARM
LIGHTS
ON
LIGHTS
OFF
PANIC
FCC Caution
Contents
This equipment generates and uses radio frequency
energy, and if not installed and used properly, that is,
in strict accordance with the manufacturers instructions,
it may cause interference to radio and television
reception. It has been type tested and found to comply
with the limits for remote control devices in accordance
with the specifications in Sub-Parts B and C of Part 15
of FCC Rules, which are designed to provide
reasonable protection against such interference in a
residential installation. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause interference to radio or
television reception, which can be determined by
unplugging the equipment, try to correct the
interference by one or more of the following measures.
To be certain of the number of devices that may be
connected to a line, as determined by the total
RENs, contact the local telephone company.
The REN for this Console is part of the product
identifier B4SAL04BJSC13A. The digits 15 represent
the REN without a decimal point (e.g., 04 is a REN
of 0.4).
Use an RJ11 connector to connect the Console to
the telephone line.
A plug and jack used to connect the Console to the
premises wiring and telephone network must comply
with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with
this product. It is designed to be connected to a
compatible modular jack that is also compliant. See
installation instructions for details.
• Reorient the antenna of the radio/TV experiencing
the interference.
• Relocate the equipment with respect to the radio/
TV.
• Move the equipment away from the radio/TV.
• Plug the equipment into an outlet on a different
electrical circuit from the radio/TV experiencing the
interference.
If the Console causes harm to the telephone
network, the telephone company will notify you in
advance that temporary discontinuance of service
may be required. But if advance notice isn’t practical,
the telephone company will notify you as soon as
possible. Also, you will be advised of your right to file
a complaint with the FCC if you believe it is
necessary.
• If necessary, consult your local dealer for additional
suggestions.
THIS DEVICE COMPLIES WITH PART 15 OF THE
FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
The telephone company may make changes in its
facilities, equipment, operations or procedures that
could affect the operation of the equipment. If this
happens the telephone company will provide
advance notice in order for you to make necessary
modifications to maintain uninterrupted service.
If trouble is experienced with the console for repair
or warranty information, please contact
www.x10.com/support. If the equipment is causing
harm to the telephone network, the telephone
company may request that you disconnect the
equipment until the problem is resolved.
This equipment complies with Part 68 of the FCC
rules and the requirements adopted by the ACTA. On
the bottom of the Console is a label that contains,
among other information, the product identifier
B4SAL04BJSC13A. If requested, this number must
be provided to the telephone company.
There are no user serviceable parts in the console.
On the bottom of the Console is a label that
contains, among other information, the FCC
registration number and ringer equivalence number
(REN) for this equipment. If requested, this
information must be provided to the telephone
company.
Connection to party line service is subject to state
tariffs. Contact the state public utility commission,
public service commission or corporation
commission for information.
Note 1: Modifications to this product will void the user’s
authority to operate this equipment.
Note 2: The security functions of this system have
not been tested by Underwriters Laboratories.
The REN is used to determine the number of devices
that may be connected to a telephone line. Excessive
RENs on a telephone line may result in the devices
not ringing in response to an incoming call. In most
but not all areas, the sum of RENs should not
exceed five (5.0).
Introduction .................................................................................................... 4
Installation ...................................................................................................... 5
Locating Security System components ....................................................... 5
Attaching the cables .................................................................................... 6
Fitting the backup batteries ......................................................................... 7
Wall mounting .............................................................................................. 7
Overview ......................................................................................................... 8
Registering Remotes ................................................................................. 12
Registering Door/Window Sensors ........................................................... 13
Removing Door/Window Sensors ............................................................. 14
Installing Door/Window Sensors ............................................................... 15
Registering Motion Detectors .................................................................... 16
Removing Motion Detectors ...................................................................... 17
Installing Motion Detectors ........................................................................ 18
Hard-wired Inputs ...................................................................................... 19
Setting the Clock ....................................................................................... 20
Setting the Phone Numbers ...................................................................... 21
Setting the Outgoing Message .................................................................. 22
Setting the PIN .......................................................................................... 24
Clearing the Memory ................................................................................. 25
Setting Options .......................................................................................... 26
Setting Delays ........................................................................................... 27
Setting Timers ........................................................................................... 28
Canceling Timers ...................................................................................... 30
Using the System ......................................................................................... 32
Arming and Disarming .............................................................................. 32
Problem zones .......................................................................................... 33
When there’s an alarm .............................................................................. 34
Controlling Lights and Appliances ............................................................. 35
Setting up Optional Lamp Modules ............................................................ 36
Operation from an Outside Telephone ....................................................... 38
Replacing Batteries ...................................................................................... 39
Resetting the P.I.N. ....................................................................................... 40
Troubleshooting ........................................................................................... 41
Expanding your System .............................................................................. 45
Introduction
Installation
The JSC1300 Supervised Security System includes the JSC13A Console, its plug-in
power supply, an RJ11 phone cord, and a telephone T adapter. The Console has an
automatic dialer that calls friends or relatives in the event of a break in, and plays a
message (in your voice). Your friend or neighbor can listen in to your home through the
Console’s microphone, and call the police if there’s a problem. Accessories include
battery powered Radio Frequency (RF) Door/Window Sensors, battery powered RF
Motion Detectors, and RF Keyfob Remote Controls for arming and disarming the system.
All sensors and remotes incorporate random digital security coding for added security.
Locating Security System components
Dining Room
The system can be configured with any combination of the following items:
• Up to 16* Wireless Keyfob Security Remotes with arm/disarm and panic functions, and
buttons to control security lights in and around the home.
Hallway
Living Room
• Up to 30* magnetic switch operated Wireless Door/Window Sensors.
• Up to 30* Wireless PIR Motion Detectors.
• Optional X10 and/or GE Home Automation modules such as plug-in lamp and
appliance modules and wired-in replacement wall switches can be added to the
system, to flash house lights on and off when the alarm trips.
Kitchen
Study
*Note: Door/Window Sensors and Motion Detectors may be added in any
combination up to a total of 30, e.g. 15 Door/Window Sensors and 15 Motion
Detectors, or any combination up to a total of 30 . There are also 2 hard wired
inputs, which are zones 31 and 32.
Some of the accessories available are shown below. Visit www.jascoproducts.com for
more.
Keyfob Remote
JKR32A
ARM
DISARM
LIGHTS
ON
LIGHTS
OFF
Locating the Security Console
Choose a location for the Security Console which is as central as possible in the house,
while providing access to a modular telephone jack and an AC outlet. The Console may
be placed on a shelf or table, or may be wall mounted.
Locating Door/Window Sensors and Motion Detectors
Plan the location of the Door/Window Sensors and Motion Detectors so that the RF path
which runs in a straight line from sensor to Console is not obstructed by large metal
objects such as a refrigerators or freezers, and passes through as few walls as possible.
PANIC
Door/Window Sensors may be hidden behind drapes for a more discreet installation.
Motion Detector
JMS18A
Door/Window Sensor
JDS12A
GE Module
RF100RXPS
Installation
Installation
Fitting the backup batteries
Security Console
Attaching cables
A telephone cord terminated at each end with an RJ11 connector is provided for
telephone connection. If possible, the Console should be connected to its own telephone
line to ensure that the line cannot be busy when the Console attempts to dial out. For
applications where this is not practical, the Console may also share a line with an existing
telephone using a ‘T’ adapter (supplied).
Note: The Security Console is not designed to operate with an RJ31X type telephone
connection.
Attach the power
supply’s cord here.
Install 4 AA alkaline batteries (not supplied) in the battery compartment. It is not
necessary to disconnect power to the Console when fitting or replacing batteries.
Replace the battery cover and securely insert the screw.
Note, if you remove the battery cover AFTER you powered up the Console, TAMPER will
appear in the display. To remove TAMPER from the display, replace the battery cover,
securely insert the screw, and then enter your PIN (default 0000). The display then shows
HOME CONTROL in the top line and the time of day below it.
Tamper Switch
(internal)
Hard Wired Inputs.
Attach the phone
cord here.
Turns on if
batteries are
low or not
installed.
Mounting the Console
The Security Console is designed to be installed freestanding, on a table top or shelf. Or
it can be wall mounted using the two slotted holes on the back of the Console.
Remove the screw and open the center lid
on the Console. Attach the power supply’s
cord to the connector labeled power
supply (see above). Plug the power supply
into any convenient (unswitched) AC
outlet. If you power up and then open the
lid, (not easy to do) the display shows
TAMPER (see next page).
NOTE: you must use the power supply
that came with the Security System. The
power supply contains circuitry required to
control X10 modules, so you CANNOT
replace it with a regular 8V DC power
supply.
If you don’t want to wall mount the console, you can flip the feet on the Console out, so as
to tilt the Console slightly forward for better viewing of the display.
Installation
Installation
Console Setup Overview
Console setup Overview, cont.
After you’ve followed the steps on page 6 and 7 and connected power to the Console, the
display shows the time of day at the left of the bottom line, with HOME CONTROL in the
top line. See below:
HOME CONTROL
12:00 am
All features (except Home Control) require access to the Menu mode. To do this, press
either of the Menu Start up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
ENTER PIN
12:00 am
Console keyboard buttons are as follows:
0-9 Used for all number entries.
On Used to send a X10/GE On message or to enter am in a time.
Off Used to send a X10/GE Off message or to enter pm in a time.
Menu up Used to initially enter the menu and then to move up through the items.
Menu down Used to initially enter the menu and then to move down through the
items.
Clear Used to clear entries, back up through the menu levels, and to bypass
problem Door/Window Sensors or Motion Detectors.
Enter Used to terminate an entry.
The default PIN is 0000, see page 24 for how you can change this, but for now press
0000 on the keypad (under the lid to the bottom left of the display). This clears the top line
and shows * for each number entered.
****
12:00 am
When you enter the PIN the display shows the First Level of the menu at step 1, below.
See next page.
1. INSTALL
To the right of the display:
Arm Home Used to arm the console in the Home mode.
Arm Away Used to arm the console in the Away mode.
Installation
Installation
First Menu Level
Sub-menus
After pressing a menu up/down button and entering the PIN, the First Level menu is
displayed, as shown below:
Once you’ve arrived at your desired first level menu and pressed OK, you can select the
sub-menus under that menu item. Alternatively you can go directly to the sub-menu item
by pressing the appropriate number button.
1. INSTALL
Phone Numbers Sub-menu
To select a menu option, press the up or down Menu button repeatedly to step through
the menu items 1 through 9 below (or you can press the number buttons 1 thru 9 on the
control panel (under the lid to the bottom left of the display) to go directly to that menu
item. Once you arrive at the menu item you desire, press OK to select it.
1.
2.
3.
4.
INSTALL
SET CLOCK
PHONE NUMS
MESSAGE
5. NEW PIN
6. MEMORY
CLEAR
7. OPTIONS
8. DELAYS
9. SET TIMER
Allows installation/removal of sensors, and/or remotes.
Enter time followed by am or pm.
Store up to six (16 digit) phone numbers.
1. RECORD (This is your own alarm message)
2. REPLAY (Replays your message).
Enter new 4 digit PIN.
Clear all Sensors, Remotes, Timers, or Master Clear.
Enter number up to 16 digits. Off/pm gives a pause.
PHONE 1
PHONE 2
PHONE 3
PHONE 4
PHONE 5
PHONE 6
Delays Sub-menu
Set Chime On/Off, Siren On/Off, Set Housecode or Light Code.
Set Exit, Entry, Dial, and Answer Delays.
Enter unit code, then On and Off time, then Daily, Once, Random or
Armed only.
To leave the first level menu press the Clear button. If you are entering numbers (for the
time, etc.), Clear will clear all numbers entered. Otherwise Clear gives the option of
leaving the menu completely and going back to the HOME CONTROL mode, or staying in
the INSTALL mode.
All times are entered in seconds, up to 99.
ENTRY DELAY
EXIT DELAY
DIAL DELAY
ANSWER DELAY
Options Sub-menu
CHIME
SIREN
HOUSECODE
LIGHTCODE
1. CHIME ON
2. CHIME OFF (No chimes when doors/windows are opened)
1. SIREN ON
2. SIREN OFF (Silent Alarm)
Chosen by Menu up/down buttons
Chosen by Menu up/down buttons
Memory Clear Sub-menu
Label on inside
of left hand lid.
Menu buttons
PRESS
THEN ENTER YOUR PIN. THEN USE
TO STEP THRU MENU ITEMS. THEN PRESS OK TO
SELECT ITEM. OR PRESS NUMBERS BELOW.
Direct Menu
access numbers
1.
2.
3.
4.
5.
6.
INSTALL
SET CLOCK
PHONE #S
MESSAGE
NEW PIN
MEMORY
CLEAR
7. OPTIONS
8. DELAYS
9. SET TIMER
CLEAR ALL SENSORS
CLEAR ALL REMOTES
CLEAR ALL TIMERS
MASTER RESET
Install Sensors & Remotes
Enter time of day
Store up to 6 phone numbers
Record/Replay your message
Change your 4 Digit P.I.N.
Sensor, Remote, Timer, Master
- Chime, Siren, H Code, L Code
- Entry, Exit, Dial, Answer delays
- Set ON/OFF Timers
CLEAR GIVES OPTION TO LEAVE THE MENU
OK button
10
11
Installation
Installation
Initializing Keyfob Remotes
Initializing Door/Window Sensors
Press and hold the ARM button on the Keyfob remote for 3-4 seconds
and then release it. This initializes the remote and picks a random
code that is used when it is registered with the Console.
Pry the two halves of the Door/Window Sensor apart and install
2 AAA alkaline batteries inside. Observe polarity.
Set switch to MAX (left) for doors, or MIN (right) for windows.
Registering the Keyfob Remote with the Console
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
Press and hold the button inside the Sensor for 3-4 seconds
and then release it. This initializes the Sensor and picks a
random code that is used when it is registered with the Console.
Replace cover and place the magnet next to the Sensor (with
the arrows aligned).
See pages 14 and 15 if you want to use an additional magnetic contact switch.
ENTER PIN
12:00 am
The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom left of
the display), or enter your PIN if you changed it (see page 24). This clears the top line
and shows * for each number entered.
****
12:00 am
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
When you see INSTALL on the display, press OK. The display then looks like this:
INSTALL
ZONE
Registering Door/Window Sensors with the Console
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
ENTER PIN
12:00 am
The default PIN is 0000, see page 24 for how you can change this, but for now press
0000 on the keypad (under the lid to the bottom left of the display). This clears the top line
and shows * for each number entered.
****
12:00 am
Now simply press any button on the Keyfob remote. The Console acknowledges that it
has been registered by beeping and displaying RMOT 1 SET.
Repeat this for any other Keyfob Remotes you want to register. The display increments to
RMOT 2 SET, etc. as you register more remotes.
Press Clear repeatedly to back out of the menu. You are asked to confirm, 1. YES, 2 NO.
Pressing 1 takes you back to the HOME CONTROL screen.
Press 2 to stay in the INSTALL menu.
12
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
When you see INSTALL on the display, press OK. The display then looks like this:
INSTALL
ZONE
13
Installation
Installation
Now move the magnet away from the Door/Window Sensor. The Console acknowledges
that it has been registered with a chime and by displaying ZONE 1 SET.
Installing the Door/Window Sensors
Repeat this for any other Door/Window Sensors you want to register. The display
increments to ZONE 2 SET, etc. as you register more Door Window Sensors. If you
connected a second magnetic switch to the contacts on the sensor (as shown on the next
page) move its magnet away to install the second magnetic switch as a separate zone.
Ideal location
Two doors or windows
(requires accessory
magnetic switch pair)
If desired, you can specify what zone you want the Door Window Sensor to be registered
into. Just press the number of the zone you want on the Console’s keypad, before you
move the magnet away to register the Door Window Sensor.
Press Clear repeatedly to back out of the menu. After a short delay the display reverts to
showing HOME CONTROL on the top line and the time of day on the bottom line.
Removing Door/ Window Sensors
Follow the steps above to install a sensor. Then when the display shows:
Sliding window
INSTALL
ZONE
Press the number of the zone you desire (just as if you were going to register the Door/
Window Sensor into that zone) but instead of registering the Door/Window Sensor, press
CLEAR on the Console’s keypad. The display asks you to confirm the deletion:
CLEAR ZONE
1. YES 2. NO
Remove shorting link
before installing hard
wired magnetic contacts.
Note when you add a magnetic
switch to a sensor you can register it
with the console as its own zone,
e.g., the sensor itself can be zone 1
and the extra magnet zone 2. See
previous page.
• Set the DELAY slide switch (inside the Sensor) to MIN (for windows) to always trigger
the alarm instantly, or to MAX (for doors) to trigger the alarm after a preset entry delay
when the system is armed in the AWAY mode.
• Attach the Door/Window Sensor to the wall using the mounting screws provided.
Replace the cover (since the unit has a tamper switch).
• Fit the Door/Window Sensor as high as possible at the top of the door/window.
Pressing 1 on the Console’s keypad changes the display to:
INSTALL
ZONE 13 OUT
Where 13 is the zone you selected. Pressing 2 instead takes you back to the INSTALL
ZONE screen.
Press Clear to back out of the menu. You are asked to confirm, 1. YES, 2 NO. Pressing 1
takes you back to the HOME CONTROL screen. Press 2 to stay in the INSTALL menu.
14
• Make sure the arrows on the magnetic and the Door/Window Sensor are facing each
other and that they separate cleanly when the door or window is opened.
• To protect two doors or windows close to each other, use the Door/Window Sensor with
an additional set of magnetic switch contacts as shown in the diagrams above.
The numbers 1 –32 in the display refer to up to 32 “zones.” These represent up to 30
Door/Window Sensors and/or Motion Detectors you install, plus the 2 hard wired zones.
The numbers show open zones, problem zones and bypassed zones by being displayed
as steady on (door or window open), slow flash (there’s a problem with that zone) or fast
flash (that zone has been bypassed). Attempting to arm with an open or problem zone
makes the Console beep continuously and it will display in words on the display what the
cause is, but only for one zone at a time. Bypassing that zone (by pressing the Clear
button) moves on to the next problem zone, if there is one.
15
Installation
Installation
Initializing Motion Detectors
Remove the cover on the front of the Motion Detector and
install 2 AA alkaline batteries in the compartment.
Replace the battery cover (the unit has a tamper switch).
Press and hold the TEST button on the back of the Motion
Detector for 3-4 seconds and then release it. This initializes
the Motion Detector and picks a random code that is used
when it is registered with the Console. Place the unit face
down, so that it won’t see any motion during the registering
process below.
Now simply press the TEST button on the back of the Motion Detector (or turn the unit
over so that it sees motion). The Console will acknowledge that it has been registered by
displaying (for example) ZONE 3 SET.
Repeat this for any other Motion Detectors you want to register. The display increments to
ZONE 4 SET, etc. as you register more Motion Detectors.
If desired, you can specify what zone you want the Motion Detector to be installed into.
Just press the number of the zone you want on the Console’s keypad, before you press
the TEST button on the back of the Motion Detector.
Press Clear to back out of the menu. You are asked to confirm, 1. YES, 2 NO. Pressing 1
takes you back to the HOME CONTROL screen. Press 2 to stay in the INSTALL menu.
Registering the Motion Detector with the Console
Removing Motion Detectors
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
Follow the steps above to install a Motion Detector. When the display shows:
ENTER PIN
12:00 am
The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom left of
the display), or enter your PIN if you changed it (see page 24). This clears the top line
and shows * for each number entered.
INSTALL
ZONE
Press the number of the zone you desire (just as if you were going to register the Motion
Detector into that zone) but instead of pressing the TEST button on the Motion Detector
(to register it) press CLEAR on the Console’s keypad. The display ask you to confirm the
deletion:
CLEAR ZONE
1. YES 2. NO
****
12:00 am
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
When you see INSTALL on the display, press OK. The display then looks like this:
INSTALL
ZONE
Pressing 1 on the Console’s keypad changes the display to:
INSTALL
ZONE 13 OUT
Where 13 is the zone you selected. Pressing 2 instead takes you back to the INSTALL
ZONE screen.
Press Clear to back out of the menu. You are asked to confirm, 1. YES, 2 NO. Pressing 1
takes you back to the HOME CONTROL screen. Press 2 to stay in the INSTALL menu.
16
17
Installation
Installation
Installing the Motion Detector
Hard-Wired Inputs
You can also connect two hard-wired magnetic contact switches to the console.
• Attach the Motion Detector to a wall at a height of 5 to 6 ft. using the mounting bracket
and screws provided.
• Point the Motion Detector so that it looks slightly downwards.
• Set the slide switch (on the back) to position 1 for instant triggering for maximum
sensitivity, or position 2 to trigger only after two movements have been sensed.
90˚
OR
ECT
DET
ION
MOT
These will be zones 31 and 32.
5-6ft
30-40ft
Replace cover. (Tamper switch
inside lid).
You can install a total of 30 additional zones, which can be a combination of Door/Window
Sensors and Motion Detectors. So, for example, you could have 15 Door/Window
Sensors, 15 Motion Detectors, and 2 hard-wired zones. The hard wired zones are treated
as delayed zones (i.e. they have exit and entry delays if you arm the system in the Away
mode).
Magnetic Switch
Contacts (sold
separately).
Remove shorting link
before installing hard
wired magnetic contacts.
Testing the Motion Detector
• Set the slide switch on the Motion Detector to position 1.
• Press and hold the TEST button for about a second (until
the LED indicator flashes twice) and then release it.
• Wait 20 seconds for the Motion Detector to settle.
• Walk in front of the Motion Detector. The LED indicator
lights each time movement is detected. Check the
coverage area and reposition the sensor as required.
• Press the TEST button to return to normal operating
mode.
Note: The Motion Detector will automatically return to
normal operating mode after about 2 minutes.
18
19
Installation
Installation
Setting the Clock
Setting the phone numbers
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
ENTER PIN
12:00 am
The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom left of
the display), or enter your PIN if you changed it (see page 24). This clears the top line
and shows * for each number entered.
****
12:00 am
ENTER PIN
12:00 am
The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom left of
the display), or enter your PIN if you changed it (see page 24). This clears the top line
and shows * for each number entered.
****
12:00 am
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
The display looks like this:
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
The display looks like this:
1. INSTALL
1. INSTALL
Press an up or down menu button until you reach the PHONE NUMS menu below, and
then press OK (or press 3, instead of up/down, to go into the PHONE NUMS menu):
Press an up or down menu button until you reach the SET CLOCK menu, and then press
OK (or press 2, instead of an up or down menu button, to go directly to the screen below):
2. SET CLOCK
4:00 pm
3. PHONE NUMS
Press an up or down Menu button to select the desired sub-menu:
PHONE 1, PHONE 2, PHONE 3, PHONE 4, PHONE 5, PHONE 6
Enter the time by pressing the digits on the Console’s keyboard. Then press am or pm.
Then press OK.
Press Clear to back out of the menu. If you press Clear while entering numbers, before
you’re finished setting the clock, it clears the numbers. If you press Clear after you’ve set
the time and pressed OK, you are asked to confirm, 1. YES, 2 NO. Pressing 1 takes you
back to the HOME CONTROL screen. Press 2 to stay in the INSTALL menu.
20
Press OK at the desired number (1-6). The display shows SET PH1, SET PH2, etc. Enter
the phone number, up to 16 digits (off/pm gives a pause). Press OK. This takes you to the
next phone number to be stored.
Press Clear to back out of the menu. If you press Clear while entering numbers, before
you’ve finished setting the phone number, it clears the numbers. If you press Clear after
you finished entering the phone number and pressed OK, you are asked to confirm,
1. YES, 2 NO. Pressing 1 takes you back to the HOME CONTROL screen. Press 2 to stay
in the INSTALL menu.
21
Installation
Installation
Recording your outgoing phone message
Press 1 for RECORD , then press OK. The display shows:
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
ENTER PIN
12:00 am
PLEASE WAIT
Then:
SPEAK NOW
The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom left of
the display), or enter your PIN if you changed it (see page 24). This clears the top line
and shows * for each number entered.
****
12:00 am
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
The display looks like this:
1. INSTALL
Press an up or down menu button until you reach the MESSAGE menu, and then press
OK (or press 4, instead of an up or down menu button, to go into the MESSAGE menu):
4. MESSAGE
Press 1 or 2 to select one of the options below:
1. RECORD
2. REPLAY
Clearly speak your message into the Console’s microphone (up to 12 seconds max.). A
typical message could be: “There’s an alarm in progress at (your address), at the end of
this message please press any button on your touch-tone phone to listen in.” After you’ve
finished speaking, wait for the display shown below:
1. RECORD
2. REPLAY
Now press 2 for REPLAY. The display shows:
PLEASE WAIT
It then plays back your recorded message. Wait for the display shown below:
1. RECORD
2. REPLAY
Press Clear to back out of the menu. You are asked to confirm, 1. YES, 2 NO. Pressing 1
takes you back to the HOME CONTROL screen. Press 2 to stay in the INSTALL menu.
Note: you cannot record messages remotely via telephone.
1. RECORD (This is your own alarm message).
2. REPLAY (This replays a previously recorded message).
22
23
Installation
Installation
Changing your Personal Identification Number (PIN)
Clearing the memory
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
ENTER PIN
12:00 am
The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom left of
the display). This clears the top line and shows * for each number entered.
ENTER PIN
12:00 am
The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom left of
the display), or enter your PIN if you changed it (see page 24). This clears the top line
and shows * for each number entered.
****
12:00 am
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
The display looks like this:
****
12:00 am
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
The display looks like this:
1. INSTALL
Press an up or down menu button until you reach the NEW PIN menu below, and then
press OK (or press 5, instead of an up or down menu button, to go directly to the screen
below):
1. INSTALL
Press an up or down menu button until you reach the MEMORY CLEAR menu below, and
then press OK (or press 6, instead of an up or down menu button, to go into the
MEMORY CLEAR menu):
6. MEMORY
CLEAR
5. NEW PIN
Press an up or down Menu button to select the desired sub-menu.
Enter your new PIN (4 digits). Press OK.
Note, choose a PIN that you are not likely to forget (a birthday, for example). If you forget
your PIN you will need to reset the system and set everything up again. See page 39.
Press Clear to back out of the menu. If you press Clear while entering numbers, before
you’re finished setting the new PIN, it clears the numbers. If you press Clear after you’ve
set the new PIN and pressed OK, you are asked to confirm, 1. YES, 2 NO. Pressing 1
takes you back to the HOME CONTROL screen. Press 2 to stay in the INSTALL menu.
24
CLEAR ALL SENSORS
CLEAR ALL REMOTES
CLEAR ALL TIMERS
MASTER RESET
Select the desired sub-menu item and then press OK. Press Clear to back out of the
menu. You are asked to confirm, 1. YES, 2 NO. Pressing 1 takes you back to the HOME
CONTROL screen. Pressing 2 stays in the MEMORY CLEAR menu. Note, selecting
MASTER RESET immediately takes you back to the HOME CONTROL screen.
25
Installation
Installation
Setting Options
Setting Delays
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
ENTER PIN
12:00 am
The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom left of
the display), or enter your PIN if you changed it (see page 24). This clears the top line
and shows * for each number entered.
****
12:00 am
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
The display looks like this:
1. INSTALL
ENTER PIN
12:00 am
The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom left of
the display), or enter your PIN if you changed it (see page 24). This clears the top line
and shows * for each number entered.
****
12:00 am
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
The display looks like this:
1. INSTALL
Press an up or down menu button until you reach the OPTIONS menu below, and then
press OK (or press 7, instead of an up or down menu button, to go into the OPTIONS
menu):
7. OPTIONS
Press an up or down menu button until you reach the DELAYS menu below, and then
press OK (or press 8, instead of an up or down menu button, to go into the DELAYS
menu):
8. DELAYS
Press an up or down Menu button to select the desired sub-menu:
CHIME
1. CHIME ON
2. CHIME OFF (No chimes when doors/windows are opened)
SIREN
1. SIREN ON
2. SIREN OFF (Silent Alarm, but Console still dials out)
HOUSECODE
For X10/GE Module (Chosen by Menu up/down buttons)
LIGHTCODE
For flashing lights (Chosen by Menu up/down buttons)
ANSWER TYPE
1. ANSWER ON 2. ANSWER OFF 3. VOICE MAIL
Select the desired sub-menu item and then press OK. Press 1 or 2 in CHIME and SIREN
sub-menus, press OK. Select the desired Housecode letter, or desired Security Light
Code, using the up/down buttons, press OK. For ANSWER TYPE: 1 always answers, 2
never answers, use option 3 if you have a voice mail service, press OK. (See page 37).
Press Clear to back out of the menus. You are asked to confirm, 1. YES, 2 NO. Pressing 1
takes you back to the HOME CONTROL screen. Press 2 to stay in the INSTALL menu.
26
Press the up or down Menu button to select the desired sub-menu:
ENTRY DELAY
(Default 30 seconds)
EXIT DELAY
(Default 60 seconds)
DIAL DELAY
(Default 5 seconds)
ANSWER DELAY
(Default 30 seconds)
Select the desired sub-menu item and then press OK. Then enter the desired delay time
in seconds up to 99 (press 0 first for single digit times). Press OK.
Press Clear to back out of the menu. You are asked to confirm, 1. YES, 2 NO. Pressing 1
takes you back to the HOME CONTROL screen. Press 2 to stay in the INSTALL menu.
Pressing Clear while entering a number (for a delay time) just clears the numbers.
27
Installation
Installation
Setting Timers to turn lights on and off (requires X10/GE Modules)
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
ENTER PIN
12:00 am
The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom left of
the display), or enter your PIN if you changed it (see page 24). This clears the top line
and shows * for each number entered.
****
12:00 am
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
The display looks like this:
To enter a new timer you must be on the NEW TIMER screen. Then press OK. The display
shows UNIT NUMBER on the top line. Using the number keys, enter a valid number (1-16)
and press OK.
UNIT NUMBER
Say for example you enter 12. The top line displays TIMER 12 ON. The bottom line
displays a colon, :
TIMER 12 ON
Enter your desired ON time with the number keys followed by am or pm in the format
shown below, (or just press OK if you don’t want to set an ON time). Press Clear if you
enter a wrong time.
TIMER 12 ON
12:34am
Then press OK. The top line displays TIMER 12 OFF. The bottom line displays a colon, :
1. INSTALL
TIMER 12 OFF
Press an up or down menu button until you reach the SET TIMER menu below, and then
press OK (or press 9, instead of an up or down menu button, to go to the NEW TIMER
menu):
Enter the OFF time as above and press OK, (or just press OK if you don’t want to set an
OFF time). Press Clear if you enter a wrong time. The display shows 1. DAILY on the
bottom line (top line blank).
9. SET TIMER
1. DAILY
You will see NEW TIMER on the top line. If no timers have been entered yet, the up and
down Menu buttons will do nothing. If there are other timers already in memory the up and
down buttons will cycle around them and will always include NEW TIMER in the loop if
there is empty space in the memory.
NEW TIMER
28
Using the up or down Menu buttons you can cycle around 1. DAILY, 2. ONCE ONLY, 3.
RANDOM, or 4. ARMED ONLY. Select the one of your choice and press OK. The display
again shows NEW TIMER. Now the up and down Menu buttons will cycle through the
entered events in the form:
12ON 12:34am
OFF 12:45pm
Note you can set a total of 12 “timer pairs” i.e., ON-OFF times. If you set an ON time with
no corresponding OFF time for that unit code (or vice versa) it still counts as a “timer pair.”
RANDOM varies the time during the programmed hour. ARMED ONLY activates the timed
event ONLY when the system is armed (for a lived-in look when you’re away).
29
Installation
Installation
Reviewing/Canceling Timers
You can cycle through (Review) your stored timers by pressing the up or down Menu
buttons. This will show the stored timers in the form below:
Press either of the Menu up/down buttons (under the lid to the bottom left of the display).
The display then shows ENTER PIN (Personal Identification Number) in the top line.
12ON 12:34am
OFF 12:45pm
ENTER PIN
12:00 am
The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom left of
the display), or enter your PIN if you changed it (see page 24). This clears the top line
and shows * for each number entered.
****
12:00 am
While a timer is on the display, pressing Clear deletes it. You are first asked: CLEAR
TIMER 1. YES 2. NO .
CLEAR TIMER
1. YES 2. NO
Pressing 1 (for YES) deletes the timer and takes you to NEW TIMER to allow you to start
entering a new timer. Pressing 2 takes you to NEW TIMER without deleting the one that
was on the screen. Press Clear to back out of the menus.
Replacing Timers
This takes you to the first level of the menu at step 1. This is the INSTALLATION level.
The display looks like this:
1. INSTALL
You can cycle through (Review) your timers by pressing the up or down Menu buttons.
This will show the stored timers in the form below:
12ON 12:34am
OFF 12:45pm
While a timer is on the display, pressing OK takes you to the Replace Timer screen below.
Press an up or down menu button until you reach the SET TIMER menu below, and then
press OK (or press 9, instead of an up or down menu button) to go into the NEW TIMER
menu):
REPLACE TIMR
1. YES 2. NO
9. SET TIMER
You will see NEW TIMER on the top line. If no timers have yet been entered the up and
down Menu buttons will do nothing. If there are other timers already in memory the up and
down buttons will cycle around them and will always include NEW TIMER in the loop if
there is empty space in the memory.
Selecting 1 for YES, takes you to the UNIT NUMBER screen below where you can
continue to enter a new timer as described on page 29. Selecting 2 for NO takes you to
the NEW TIMER screen so you can enter a new timer without replacing the existing one.
Press Clear the back out of the menus.
UNIT NUMBER
NEW TIMER
Note, you can also clear ALL timers as described on page 25.
30
31
Using the system
Using the system
Arming the system
If there’s a problem
Press ARM HOME on the Console to arm ALL Door/Window Sensors instantly. Motion
Detectors will not trip the system when it is armed in the ARM HOME mode.
If a door or window is open and you try to arm the system the display looks as below.
(Where ZONE 9 is the door or window that’s open).
Press ARM AWAY to arm all Door/Window Sensors and Motion Detectors. This arms the
system after a set delay. The delay will be what you specified as the EXIT DELAY on page
27 (1 minute default). If you arm the system in the AWAY mode you will also have an
entry delay when you enter your home before the alarm trips (from Door/Window Sensors
set to MAX, and from Motion Detectors), to give you time to disarm it. This delay will be
what you specified for your ENTRY DELAY on page 27 (30 second default).
Pressing ARM on the Keyfob remote always arms in the AWAY mode, (instantly). ALL
Door/Window Sensors and Motion Detectors trip instantly when armed from the Keyfob.
Disarming the system
OPEN
ZONE 9
If a Door/Window Sensor or Motion Detector has not reported in within the last 4 hours,
and you try to arm the system, the display looks as below. (Where ZONE 12 is the Door/
Window Sensor or Motion Detector that hasn’t reported in).
PROBLEM
ZONE 12
Pressing DISARM on the Keyfob remote disarms the system instantly. The zone that was
violated is shown in the display. To remove this press Arm and Disarm again.
To disarm from the Console: Enter your 4 digit PIN (Personal Identification Number) this
will be 0000 unless you changed it (see page 24).
ARMED HOME
12:00 am
If a Door/Window Sensor or Motion Detector has been tampered with, e.g. the battery
cover is open, and you try to arm the system, the display looks as below. (Where ZONE 4
is the Door/Window Sensor or Motion Detector that has been tampered with).
TAMPER
ZONE 4
Entering the PIN clears the top line and shows * for each number entered.
****
12:00 am
If the unit is armed it will disarm when the PIN is entered, and return to the time display,
with DISARMED in the top line.
DISARMED
12:00 am
Then after a short delay the display reverts to HOME CONTROL mode.
32
For an open or problem zone, pressing the Clear (Bypass) button bypasses the problem
zone and lets you arm the system. After pressing Bypass the next problem zone is
displayed, (if there is more than one).
You can’t arm the system while there’s a problem zone unless you fix the problem, or
bypass the zone. If you try to arm the system while there’s a problem with one or more
zone you will hear a repetitive “trouble alarm” to alert you that you need to bypass or fix
the problem zone(s).
If you bypass a zone and then arm the system, that zone stays bypassed until you disarm
the system.
If a Door/Window Sensor, Motion Detector, or the Console has been tampered with, you
must fix the problem (close the battery cover) and then enter your PIN, before you can
arm the system. Note if the system is armed and a tamper occurs, the alarm trips.
33
Using the system
Using the system
When there’s an alarm
If the system is tampered with
When the system is armed (in Home or Away mode) and you open a protected door or
window, or walk past a Motion Detector (if armed in the Away Mode), or activate the Panic
feature (by pressing BOTH Panic buttons at the same time on the Keyfob Remote) the
alarm trips. The following then happens:
• A loud siren sounds.
• Lights (set to the security code) flash on and off (if you set up X10/GE modules).
See pages 26, 36, and 37.
• The Console dials the first phone number you set up. It then starts to play the recorded
message you stored. E.G. “There’s an alarm in progress at (your address), at the end
of this message please press any button on your touch-tone phone to listen in.” Note, it
might take a while before the person the Console called picks up the phone so they
might miss the first part of your message, but the message is repeated 3 times, so
they will get to hear the complete message.
When the person who was called answers the call, listens to the message, waits for a gap
between messages, and then presses a button on their phone. This activates a
microphone in the Console so they can listen in to your home, and will be able to
determine if there is suspicious activity going on. They can then take action. E.G. call the
Police for you. Note, if no one presses a button on their phone to listen in, as would
happen if an answering machine picked up the line, the console dials the next number
you programmed it to (up to 6 numbers).
IMPORTANT: Do NOT program the Console to call the Police directly.
Note, the person who answers the phone needs to wait for a gap between the messages
before they can press a button on their phone to listen in (the message repeats three
times, but might have already played once or twice before the person answers the
phone).
If the system is armed and someone tampers with (opens the battery cover) on a Door/
Window Sensor, Motion Detector, or the Console, the same thing happens as when the
alarm is tripped by any other method. If the system is NOT armed and someone tampers
with a Door/Window Sensor, Motion Detector, or the Console, the word TAMPER appears
in the display but the system does not trip. You must fix the tamper, (close the battery
cover) then enter your PIN to remove the word TAMPER from the display.
Controlling lights and appliances
If you install one or more Lamp Modules (sold separately), see pages 36 and 37, you can
control lights around your home from the Console. When the Console is in its normal
state it displays HOME CONTROL in the display. When its in this state you can simply
press the number button on the Console corresponding to the number set on the module
and then press On or Off on the Console’s control panel to control the light connected to
the module.
You can also control lights set to your Security LIGHTCODE from the Light On and Light
Off buttons on the Keyfob Remote. These buttons on the Keyfob Remote control lights
connected to X10/GE Modules that are set to the Security LIGHTCODE you set in the
Console. (See page 26). To control GE Modules your LIGHTCODE must be a number
between 1 and 8. For X10 Module your LIGHTCODE can be any number (1-16).
Also, any lights connected to X10/GE Modules that are set to your Security LIGHTCODE
flash on and off when the alarm trips. They stay on after an alarm until you turn them off,
either from the Console, or from the Keyfob Remote.
These lights also blink on for a second when the alarm is armed (from the Console) in the
ARM HOME Mode (or when armed from the keyfob Remote). Or these lights turn on for
the exit delay time when the alarm is armed from the Console in the ARM AWAY Mode.
If no one answers the call (and presses a button on their phone) before the third message
is played, the Console dials the next number stored. It can take quite a long time to dial all
the numbers if you’ve stored 6 of them, and no one answers. But the siren stops sounding
after 4 minutes in any case (usually required by local ordinance). The unit still dials all the
numbers stored unless someone answers the call and presses a button on their phone.
At the end of the 4 minutes the alarm stops, but the armed state is unchanged. I.E., the
alarm is still armed. Any open Door or Window is automatically bypassed at that point. So
if a burglar has opened a window to get in, set the alarm off, but left the window open, the
system continues to protect all other doors and windows without that Door/Window
Sensor. (If it did not bypass it, the alarm would trip again whenever that Door/Window
Sensor reported in again, which it does every 90 minutes).
34
Controls lights connected
to X10/GE modules that
are set to the Security
LIGHT CODE you set in
the Console (see page 26).
Press both buttons at the
same time to activate the
panic alarm.
35
Optional X10 Lamp Modules
Optional GE Lamp Modules
Setting the (optional) X10 Lamp
Module’s Code
UNIT CODE
DIAL
Using a small screwdriver, set the red
House Code dial to the same letter as
your Console is set to. Set the Black Unit
Code dial to your Security Code (see
page 26).
UNIT CODE
DIAL
Setting the (optional) GE Lamp
Module’s Code
Set the Unit Code dial on the front of the
GE Module to your Security Code. Must
be between 1 and 8. (See page 26).
HOUSE CODE
DIAL
Ratings
The Lamp Module can be used to control an incandescent lamp rated up to 300W. It is
not suitable for other types of lamps such as fluorescent or energy saving lamps, low
voltage lamps, or lamps that include a dimmer control. Caution: Do not connect an
appliance such as a coffee pot or heater to a Lamp Module. It may damage the Module
and/or the appliance and could cause a fire hazard. Use an Appliance Module instead.
Set the House Code on the GE Module(s) to match the House Code for the Console (see
page 26). To set the Module’s House Code, remove the small tab labelled House Code on
the back of the GE Module using a small screwdriver. Set the House Code to match the
Console’s House Code (the Console must use House Code A, B, C, or D if you want it to
control GE Modules).
House Code A
shown
1.
Set the House Code
and Unit Code.
2.
Plug a lamp into
the Module.
3.
Plug the Module into
the same wall outlet
as your controller (see
testing below).
Follow the instructions that came with the GE Module(s) and observe the ratings on the
back of the module: 1200W Max. resistive load, 600W Max. tungsten lamps, 1/3 HP
motor load.
Testing The X10 Module(s)
Testing The GE Module(s)
Make sure the lamp's switch is on. Plug the X10 Lamp Module into the same wall outlet
as your Console’s power supply, press the number button on the Console that
corresponds to the Unit Code setting on the Module (1-16), then press On or Off. If the
Module turns on and off you can unplug the Module and move it to its permanent location.
If you can’t control the module, visit www.x10.com/support for help.
Make sure the lamp's switch is on. Plug the GE Module into the same wall outlet as your
Console’s power supply, press the number button on the Console that corresponds to the
Unit Code setting on the Module (1-8), then press On or Off. If the Module turns on and
off you can unplug the Module and move it to its permanent location. If you can’t control
the module, visit www.jascoproducts.com for help.
36
37
Operation from an Outside Telephone
Battery Information
The Console has remote telephone access, with voice responses to acknowledge receipt
of remote commands.
General
When you call home, the Console answers and says “Please enter PIN.” You enter your
PIN using the touch tone buttons on the remote telephone.
Door/Window Sensors, Motion Detectors and Keyfob remotes are designed to operate for
approximately one year when fitted with the appropriate batteries. Since operating
conditions vary from installation to installation however, it is recommended that all
batteries are replaced every 6 months.
If the PIN is entered correctly it says “PIN accepted”. If wrong it says “Error.”
Pressing 0, then * (on the remote telephone’s touch tone keypad) arms the Console.
Pressing 0, then # disarms the Console.
Pressing 9, then 9, then * tells you the current system status: I.E. it says Armed Home,
Armed away, Disarmed, Panic alarm, or Alarm in zone (1 – 32).
The numbers 1 –32 in the display refer to up to 32 “zones.” These represent the Door/
Window Sensors/Motion Detectors you installed. Therefore if the alarm tripped because
zone 3 was violated, when you call in and press 9, 9, * you will hear “Alarm in zone 3.”
Remotely controlling lights (or appliances) via telephone
If you install X10 or GE modules (sold separately), see pages 36 and 37, you can control
lights and appliances around your home from any touch tone telephone in the world.
Security Console
Battery backup
The batteries in the Security Console are used as a backup when there has been a
power failure. The batteries provides approximately 12 hours of backup time provided the
alarm has not been triggered.
While on battery backup, the Console will continue to operate, and will sound the siren
and dial out if the alarm is tripped. It will not, of course, flash the house lights (because
there’s no AC power).
If both the AC supply and the batteries fail, the Console will no longer dial out or sound
the siren. You will NOT lose its stored telephone numbers, recorded message, or installed
sensors and remotes, but you WILL need to reset the clock for the correct time of day.
Battery Replacement
When you call home, the Console answers and says “Please enter PIN.”
If the PIN is entered correctly it says “PIN accepted”. If wrong it says “Error.”
If you then press 4, then * on the touch tone phone, it says “4 On” and turns on any X10/
GE module(s) set to Unit Code 4 (and the same Housecode as the Console is set to).
If you then press 1, then 6, then # on the touch tone phone, it says “16 Off” and turns off
any X10 module(s) set to Unit Code 16 (and the same Housecode as the Console is set
to). Note, GE Modules can only be set to 1-8. See page 26 to change the Housecode.
If you have an answering machine, or voice mail service.
If you own an answering machine, you will normally set it to answer after a few rings. In
this case, when the answering machine answers a call (or if there’s someone home who
picks up the phone), the security system will NOT answer the call and will NOT say
“Please enter PIN.” You can still however go ahead and enter the PIN to access the
security system features above. Just wait until your answering machine finishes its
outgoing message and then enter your security system PIN. Note, your answering
machine will record the touch tones you hear when you press buttons to turn lights on
and off, etc. and will also record the messages played back by the security system.
If you have voice mail provided by your phone company, you can set the Console so that
you call once, hang up and call right back (within 20 seconds). On the second call the
Console answers (so the call doesn’t get diverted to voice mail). See Options on page 26.
38
Batteries can be replaced at any time, even while the unit is powered up. There is no
special procedure for battery replacement. Use 4 AA alkaline batteries.
Keyfob Remotes
Battery Replacement
Providing the batteries have not already failed, they can be replaced with fresh batteries
without the need to reregister the remote. After removing the old batteries fresh batteries
must be fitted within 30 seconds to ensure that the security code is retained.
Gently pry the 2 halves of the Keyfob Remote’s case apart and install two CR2016 lithium
batteries in the compartment (+ facing up). Press the 2 halves of the cabinet back
together.
Once the batteries have been replaced, confirm that the remote is still registered with the
Console by arming the system. If it does not arm, the code has been lost and you will
need to proceed as described below.
If the batteries have failed completely, the remote’s code will have been lost. The remote
will need to be reinstalled following the procedure on page 12.
39
Battery Information
Troubleshooting
Door/Window Sensors and Motion Detectors
Battery Replacement
PROBLEM
SOLUTION
If the system does not arm.
• Check that the indicator on the Remote
turns on when you press ARM.
Replace the batteries and reregister
the Remote with the Console if
necessary.
Console displays PROBLEM followed by
Zone number when you try to arm it.
One of the sensors/motion detectors has
not reported in, in the last 4 hours.
If a zone has not reported in to the Console during the last four hours, the display will
show PROBLEM and the appropriate zone number when you try to arm the system. This
is most likely caused by dead batteries in the sensor for that zone.
As with the remotes, as long as the batteries have not completely failed they may be
replaced with fresh batteries without the need to reregister the Door/Window Sensor or
Motion Detector. After removing the old batteries the new batteries must be fitted within
30 seconds to ensure that the code is retained.
Check that the batteries in the sensor/
motion detector are good.
Testing the Door/Window Sensor
Or a protected door or window is open.
Once the batteries have been replaced, the Door/Window Sensor should be tested as
follows:
• Make sure the system is NOT armed.
If you need to arm the system and want
to ignore a sensor/motion detector which
is not functioning:
• Open the door or window with the sensor attached. The Console chimes to
acknowledge and the zone # is displayed on the LCD.
1. Press CLEAR on the Console while
the problems is being displayed.
• If you don’t hear a chime, reregister the Door/Window Sensor, as described on page 13
2. Then press ARM on the Remote. The
problem zone is not protected but all
other zones are armed.
Testing the Motion Sensor
To test the Motion Detector:
• Make sure the system IS armed.
• Walk past the Motion Detector. The alarm trips. Press disarm on the Keyfob Remote.
If you hear a repetitive trouble alarm
when you try to arm the system, and it
does not arm.
Check the Console’s display. If a door or
window is open, its zone # will indicate
there’s a PROBLEM.
• If the alarm doesn’t trip, reregister the Motion Detector, as described on page 16.
• Press DISARM. Check each Door/
Window Sensor is working properly
and that no doors or windows are
open. Then arm the system.
Clearing Remotes & Sensors from the Console
If you suspect that a neighbor’s system is causing false alarms, or if you need to reinstall
Keyfob Remotes, Door/Window Sensors, and/or Motion Detectors for any other reason,
you can clear all sensors and remotes from the Console’s memory by following the steps
on page 25. Before reregistering your remotes, Door/Window Sensors, and Motion
Detectors you should reinitialize them - remove the batteries, press a button for 5
seconds then refit the batteries. Then follow the steps to reinitialize the unit (pages 12, 13,
or 16 as appropriate).
Or:
• While the trouble alarm is sounding,
press CLEAR on the Console to
bypass the problem zone (the display
shows that it has been BYPASSED).
Then arm the system again.
If you forget your PIN
• Or if the display shows TAMPER,
check the cover on the sensor or
motion detector for that zone.
While in normal Home Control mode:
Press 7, 9, On. The display shows all 32 numbers and all letters A thru Z.
Press Clear. The display returns to Home Control, and the PIN is reset to 0000.
Note, everything in the Console is reset so you will need to set everything up again.
40
• Or check that the center lid on the
Console it closed.
41
Troubleshooting
Troubleshooting
PROBLEM
SOLUTION
PROBLEM
SOLUTION
If the alarm trips when you enter the
house before you have time to disarm it.
Arm the system in the AWAY mode.
If you do not hear a beep from the Console
when you press ARM to install a Remote.
Reinitialize the remote (see page 12).
Lights will not turn on or off from the ON
or OFF buttons on the Keyfob Remote.
• Be sure you set the correct SECURITY
LIGHT Code in the Console, see
pages 26 and 35.
If you do not hear a beep from the
Console when you register a Door/
Window Sensor or Motion Detector.
With the Console NOT armed check that
it chimes when you press TEST inside the
Door/Window Sensor, or the alarm trips
when you press test on a Motion Detector
(when the system IS armed). If it does,
then the sensor is already installed and
no further action is necessary. If not:
• Be sure the light you are trying to
control has its on/off switch in the on
position. Be sure its bulb is good.
• Plug the Module into another outlet
near the Console.
• Check that the indicator on the Keyfob
Remote comes on when you press a
button. Replace batteries and
reregister the remote if necessary.
• Check the dials on the Modules.
You open a door or window and the alarm
does not trip.
• Reregister the sensor/motion detector
(see Setting Up Door/Window Sensors
and Setting Up Motion Detectors.
If the battery indicator on the Console is
on.
Replace the Console’s batteries. Four AA
alkaline batteries provides approximately
12 hours of backup. Replace batteries at
least once a year.
If you lose your remote control.
Reregister your complete system to
prevent someone else from using the lost
remote control. See bottom of page 39.
If the system Arms or Disarms by itself
A neighbor may have a compatible
system. Reinstall the complete system so
that it chooses different RF codes. See
bottom of page 39.
If the light on the Keyfob Remote stays on
during initialization.
Remove the batteries, press a button for
a few seconds, release, then replace the
batteries. Press and hold the ARM button
on the Keyfob Remote for a few seconds
and then release it. This initializes the
remote and picks a random code that is
used when it is registered with the
Console. Reregister the remote.
• Check that the system is armed.
• Check to see if the alarm trips when
you press TEST inside the Door/
Window Sensor.
• If the alarm does not trip when you
press TEST, check that the indicator on
the sensor comes on when you press
TEST.
If the indicator does not come on, replace
the batteries and reinstall the sensor if
necessary.
The system flashes lights by repetitively
transmitting the SECURITY light on and
off code.
If appliances turn off during an alarm.
Any Appliance Modules set to the same
code will therefore turn on and off.
42
43
Troubleshooting
Expanding Your System
PROBLEM
SOLUTION
The alarm cause is shown on the display
even after disarming.
To remove, Arm and Disarm from a
remote, or disarm by entering the PIN on
the Console.
If the optional PowerHorn does not trip
when the alarm trips.
• Be sure you set the dials on the
PowerHorn to the same SECURITY
LIGHT code as set in the Console, see
page 26.
The GE Security System can flash lights on and off when the alarm trips. You connect the
lights you want it to control to X10 and/or GE Lamp Modules, Wall Switch Modules, and
Screw-in Modules (sold separately). The SC13A Security Console acts as a “Transceiver”
and passes commands received from wireless remote controls onto your house wiring, so
you can use X10 wireless remote controls to control the same lights that the Security
System flashes. You can also use X10 remote controls to control Appliance Modules, etc.
The system also sends RF wireless commands to GE wireless modules.
The SC13A Security Console also works with X10 wireless motion detectors, again acting
as a Transceiver, to pass the commands from the motion detectors to the X10 Modules.
• Plug the PowerHorn into another outlet
near the Console.
The Motion Detector causes false alarms.
• All brands of motion detectors sense
motion by detecting a change in
temperature, therefore do not place the
detector near any sources of heat such
as over a heating vent or an air
conditioner.
• Do not place in a direct source of
bright light, such as sunlight.
Siren doesn’t sound when the alarm is
tripped.
Check that you didn’t accidentally set the
Console for Silent Alarm (SIREN OFF).
See Options settings on page 26.
If TAMPER appears in the display.
Fix the problem (close the battery cover
on the Sensor or the Console, then enter
you PIN.
LIMITED 90 DAY WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for
a period of ninety days from the original date of consumer purchase. This warranty is
limited to the repair or replacement of this product only and does not extend to
consequential or incidental damage to other products that may be used with this unit.
This warranty is in lieu of all other warranties express or implied. Some states do not
allow limitations on how long an implied warranty lasts or permit the exclusion or
limitation of incidental or consequential damages, so the above limitations may not apply
to you. This warranty gives you specific rights, and you may also have other rights which
vary from state to state. If unit should prove defective within the warranty period, return
prepaid with dated proof of purchase to:
Jasco Products Company
311 N.W. 122nd
Oklahoma City, OK 73114
Intercom Systems
Intercom systems which send voice signals over existing electrical wiring may interfere
with the ability to control X10 Modules from your security system with the intercom in use.
If the intercom system has its own separate wiring it will not cause a problem.
44
45
Notes
Notes
46
47
Jasco Products Company
311 N.W. 122nd
Oklahoma City, OK 73114
JSC1300 -02/05
Supervised Security System

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 25
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:cb03818e-f01a-4442-a6fb-fb52b3217094
Producer                        : Acrobat Distiller 5.0 (Windows)
Create Date                     : 2005:11:04 23:42:04Z
Modify Date                     : 2005:11:04 19:26:10-05:00
Metadata Date                   : 2005:11:04 19:26:10-05:00
Creator Tool                    : PageMaker 7.0
Document ID                     : uuid:63a6d812-88e8-49d5-9905-6eb9d268ec0d
Format                          : application/pdf
Creator                         : Dave Rye
Title                           : Jasco JSC1300-OM.pmd
Author                          : Dave Rye

EXIF Metadata provided by EXIF.tools