Avantronics BTRC-300 Avantree Roxa User Manual
Avantronics Limited Avantree Roxa
Users Manual
1. Product Description Function Now you can enjoy both smartphone and tablet music through your home stereo or stand-alone speaker wirelessly, via the Avantree Roxa. Roxa is a simple to use Bluetooth 4.0 home music receiver which incorporates new apt-X decoder for less latency, high quality music. Plug Roxa into a wall socket and relax into the music – no need to worry about the Roxa powering off. The extra 1A USB charging port enables you to charge your phone and enjoy music at the same time! 2. Product Overview (1) LED Indicator (2) 3.5 mm audio socket (3) 1A USB charging port (4) Pin power plug (US / EU / UK Pin optional) Operation Power on Plug Roxa into standard AC socket Red LED stays on. Turn on Bluetooth Plug 3.5 mm audio cable end into Roxa’s 3.5 mm audio socket Red LED off, and blue LED blinks every 1 second (this lasts for 10 seconds) Enter pairing mode Roxa will enter pairing mode automatically when turned on Blue and red LED lights blink alternately and quickly (this lasts for 2 minutes) Turn off Bluetooth Pull the 3.5mm audio cable from Roxa’s 3.5 mm audio socket Blue LED off, red LED stays on What’s in the box: LED indicator Step 2 – double click Roxa and connect Notes: 1) When Roxa is already connected with 2 devices and turned on again, it will connect with these two devices automatically. 2) Roxa can only output music from one Bluetooth device. If you want to play music from another Bluetooth device, please pause current device’s music first. 3) Roxa can only be paired and connected with 1 desktop or laptop a time, due to chipset firmware issues. 6. Advanced feature – Supply 1A power for other electronics device USB port of Roxa can provide DC 5V – 1A for charging other electronic devices. You can charge devices via USB port and stream music at the same time. Step 3 – set Roxa as your audio device Notes: The pairing mode will last 2 minutes. Roxa will enter standby mode automatically if no device can be connected and paired within 2 minutes (if the 3.5 mm cable is still plugged into Roxa’s 3.5 mm socket). • Avantree Roxa • 3.5mm to 3.5mm audio cable • 3.5mm to RCA audio cable • User manual • Warranty card 2) Pairing with Bluetooth phone / tablets Please make sure your phone has Bluetooth function and it is available. The pairing procedures are different for different devices. Please refer to your cell phone / tablet / laptop / desktop user manual for further instructions. -1- Notes: 1) Please use standard USB cable which are compatible with your device. 2) The USB port can only provide DC 5V, and the charging current will not exceed 1A. -3- 3. Setting up your Bluetooth home music receiver (A) The red LED will go on automatically when the device is plugged into a standard AC socket. (B) Plug the 3.5 mm audio cable into Roxa’s 3.5 mm audio socket, and plug the other end (or 2 x RCA) into the audio input of your home stereo system – Roxa’s blue LED will go on. 10 seconds later it will enter into pairing mode – the red and blue LEDs will blink quickly. Pairing mode will last for 2 minutes. (C) Paired with Bluetooth phone / tablet / PC or other Bluetooth transmitter. (D) After successfully pairing and connect you can enjoy music from your home stereo speaker, and control play-lists via your phone within a 10 meter range. -5- The general pairing procedures are as follows (taking iPhone as an example): Now you can stream music over to your hi-fi (A) Put Roxa and iPhone within 1 meter for pairing. (B) Make Roxa into pairing mode (refer to “ Enter pairing mode” above) (C) From your iPhone home page, tap “settings” “General “ “ Bluetooth” “ On” (D) iPhone will auto scan the available Bluetooth devices. Choose “Avantree Roxa” from the list of devices shown, and according to the indication, tap ”Connect” or “Yes” or enter password or Pin no. “0000”( for some other Bluetooth devices). (E) After pairing successful, complete Blue LED will blink twice every 4 seconds. Notes: 1) Roxa can remember eight paired devices, when the number of devices exceeds eight, the first one will be replaced. 2) If the phone and Roxa over range (normally exceeds 10 meter or above), the Roxa will disconnect and enter standby mode. It will connect automatically if phone and Roxa back to available range within 5 minutes. Or you can select Roxa on the phone. 6.1 LED indicator We find most problems are caused by improper pairing. Please follow the online instructions step-by-step. 22 3)Paring with Mac The general pairing procedures please kindly reference below steps: Step 1 – search bluetooth device from MacBook 5. Advanced feature – Multipoint for smartphone / tablet Roxa can connect with 2 phones or 2 tablets or 1 phone and 1 tablet simultaneously, pls. follow below steps: MUSIC AC Socket Pairing 3.5MM Jack Avantree Roxa PIN 0000 or Tap connect 3.5MM (A) Pair and connect Roxa with device 1 (phone) first. (B) Then turn off Bluetooth function on device 1 (phone), and unplug the 3.5 mm audio cable from Roxa, Roxa pair and connect with device 2 (phone).(Details please kindly take reference to 4. Pairing with a Bluetooth device) (C) Activate Bluetooth function of device 1 (phone), and operate device 1 (phone) to connect with Roxa. 4. Pairing with a Bluetooth device (Tutorial online) 1) Enter pairing mode -2- B) Why can't Roxa be paire and connect with a laptop? Pls. kindly make sure your laptop have Bluetooth function and the bluetooth software support audio profile transmite. C) Why can’t Roxa automatically connect with the phone after coming back within range? If it is out of range, Roxa should connect with the phone automatically. If more than 5 minutes have elapsed, you can connect it by operating your phone. -4- 9.2. FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -7- Status of receiver LED indicator Powered on but Bluetooth not activated Red LED on for long time Pairing mode Blue and red LEDs flash alternately and quickly lasts for 2 minures Standby mode (no device connected) Blue LED flashes once every 2 seconds Standby mode (device connected) Blue LED flashes twice every 8 seconds Charging and Bluetooth in standby mode (device connected) Blue LED flashes twice every 8 seconds Charging and Bluetooth in standby mode (no device connected) Blue LED flashes once every 2 seconds 6.2 F A Qs A) Why can’t Roxa be paired with a phone? 1) Please make sure Roxa is in pairing mode. 2) The paring mode will last 2 minutes, it will enter standby mode automatically if exceeds 2 minutes. 3) Please turn on Roxa’s Bluetooth function again to enter pairing mode again. -6- -8- • Service must be done by qualified service center or manufacturer. • Unplug this device when unused for long periods of time or during lightening storms. Simply Convenient CAUTIONS: ELECTRIC SHOCK HAZARD The battery used in this device may present a risk of fire or chemical burn if mistreated. Bluetooth 4.0 Home Music Receiver ( Roxa) Enjoy outstanding music from home stereo system wirelessly Note: The manufacturer is not responsible for ANY interference, for example RADIO or TV interference, caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. 7. Product Specification Bluetooth receiver • Bluetooth V4.0 + EDR • Support profile: A2DP, AVRCP • Support decoders: aptX, SBC • Operation distance: Class 2, 10 Meter Audio • Output impedance line out: 32Ω • Total harmonic distortion: 0.6% • Signal to Noise Ratio: ≥60dB (1KHz,A-WEIGHTED) • Frequency response: 20~20000Hz 9.3. IC Statement This device complies with Industry Canada license-exempt. RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement." AC power • Input voltage: AC100-240V 50/60Hz • USB output voltage / Current: 5V / 1000mA • Weight: 45.6g -9- Roxa User Guide 9.4 FCC RF exposure - 11 - - 13 - - 15 - • Size: 45.5*55.5*33.5mm This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 8. Safety Information • To avoid any damage or malfunction of the device, do not drop it from high places. • Keep device away form humidity, water and any other liquid. If the device is exposed to water, moisture and other liquid, do not operate it to avoid any electrical shock, explosion and damage to the device or yourself. • Do not place or keep this device near any heat source, such as, direct sun light, radiators, stoves or other apparatus which produces heat. It may cause explosion, degrade the performance and/or reduce battery life. • Do not modify, repair or disassemble device at discretion (Especially battery: It may cause an explosion). Doing this will avoid the warranty. • Do not place heavy objects on the device. • Use only supplied and approved charger. • Replacement or service must be done by qualified service center or manufacturer. • Unplug this device when unused for long periods of time or during lightning storms. CAUTION: ELECTRIC SHOCK HAZARD The battery used in this device may present a risk of fire or chemical burn if mistreated. 9. Declaration of Conformity 9.1. EU This product is CE certified according to the provision of the R&TTE Directive (99/5/EC). Declare that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. - 10 - Online Tutorial & Technical Support 9.5. Trademark Statement The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. Avantree is a trademark owned by Avantronics limited. aptX™ words and logos marked with a ™ or ® are trademarks registered or owned by CSR plc or one of its group companies and may be registered in one or more jurisdictions except that not all such marks are registered in all countries where products are available. For more information about this product and other Avantree Bluetooth products, including the video user guide, product tutorial and online technical support, please refer to www.avantree.com website. Due to software updates, there could be some changes of operations. Please always refer to Product Tutorial page on Avantree website for the latest features. iPhone is the trade mark of Apple inc. 10. Warranty Dispose of the packaging and this product in accordance with the latest provisions. • To avoid any damage or device malfunction, do not drop the device from high places. • Keep the device away from humidity, water and any other liquid. If the device is exposed to water, moisture and other liquid, do not operate it to avoid any electrical shock, explosion and damage to the device or yourself. • Do not place or keep this device near any heat source, such as, direct sun light, radiators, stoves or other apparatus which produces heat. It may cause explosion, degrade the performance and/or reduce battery life. • Do not modify, repair or disassemble the device (Especially battery: It may cause an explosion). Doing so will void the warranty. • Do not place heavy objects on the device. • Use only the supplied and approved charger. - 12 - - 14 - FCC ID: WJ5-BTRC-300 Z-PKMN-BTRC300-0000 - 16 -
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Page Count : 1 Creator : Adobe Illustrator(R) 15.0 For : adma, Create Date : 12/27/2012 5:54 PM Bounding Box : -112 -1263 1347 -199 Container Version : 11 Creator Version : 15 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:2dd52aa7-e32c-4dfc-a1e8-84f7350e0d81 Startup Profile : Print Producer : Adobe PDF library 9.90 Metadata Date : 2013:01:10 14:18:12-08:00 Modify Date : 2013:01:10 14:18:12-08:00 Creator Tool : Adobe Illustrator CS5 Thumbnail Width : 256 Thumbnail Height : 188 Thumbnail Format : JPEG Thumbnail Image : (Binary data 21316 bytes, use -b option to extract) Instance ID : uuid:bc5e1ce5-503b-403c-9ce5-7e4767d19d5a Document ID : xmp.did:06368558814DE2119161A5505DBFD352 Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:05368558814DE2119161A5505DBFD352 Derived From Document ID : xmp.did:05368558814DE2119161A5505DBFD352 Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved, saved History Instance ID : xmp.iid:04368558814DE2119161A5505DBFD352, xmp.iid:05368558814DE2119161A5505DBFD352, xmp.iid:06368558814DE2119161A5505DBFD352 History When : 2012:12:24 13:55:51+08:00, 2012:12:24 14:17:12+08:00, 2012:12:24 14:30:20+08:00 History Software Agent : Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5 History Changed : /, /, / Has Visible Overprint : False Has Visible Transparency : True N Pages : 1 Max Page Size W : 563.384044 Max Page Size H : 395.757756 Max Page Size Unit : Millimeters Font Name : Arial-BoldMT, Arial-Black, ArialMT, Calibri-Italic, LubalinGraphEF-Medium, Tahoma-Bold, Tahoma, AdobeSongStd-Light Font Family : Arial, Arial, Arial, Calibri, LubalinGraphEF, Tahoma, Tahoma, Adobe 宋体 Std Font Face : Bold, Black, Regular, Italic, Regular, Bold, Regular, L Font Type : Open Type, Open Type, Open Type, Open Type, TrueType, Open Type, Open Type, Open Type Font Version : Version 3.00, Version 2.40, Version 3.00, Version 1.02, 001.000, Version 3.15, Version 3.15, Version 5.010;PS 5.002;hotconv 1.0.57;makeotf.lib2.0.21895 Font Composite : False, False, False, False, False, False, False, False Font File Name : ARIALBD.TTF, ariblk.TTF, ARIAL.TTF, CALIBRII.TTF, LubalinGraphEF-Medium.ttf, tahomabd.TTF, TAHOMA.TTF, AdobeSongStd-Light.otf Plate Names : Cyan, Magenta, Yellow, Black, PANTONE 376 U Swatch Groups Colorants Tint : 100.000000 Swatch Groups Group Name : 鲜艳 Swatch Groups Group Type : 1 Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0 Swatch Groups Colorants Mode : CMYK Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Cyan : 60.000002 Swatch Groups Colorants Magenta : 90.000004 Swatch Groups Colorants Yellow : 0.003099 Swatch Groups Colorants Black : 0.003099 Format : application/pdf Title : 打印EXIF Metadata provided by EXIF.tools