Avaya Callpilot Message Networking User Guide
2015-06-01
: Avaya Avaya-Callpilot-Message-Networking-User-Guide-735499 avaya-callpilot-message-networking-user-guide-735499 avaya pdf
Open the PDF directly: View PDF .
Page Count: 22
Download | |
Open PDF In Browser | View PDF |
Part No. P0919430 04 CallPilot Message Networking User Guide CallPilot Message Networking User Guide Copyright © 2002 Nortel Networks All rights reserved. 2002. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel Networks NA Inc. The software described in this document is furnished under a license agreement and may be used only in accordance with the terms of that license. The software license agreement is included in this document. Trademarks NORTEL NETWORKS is a trademark of Nortel Networks. Microsoft, MS, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation. All other trademarks and registered trademarks are the property of their respective owners. P0919430 04 3 CallPilot Message Networking User Guide About Message Networking This guide explains how to use Message Networking with your personal mailbox. Message Networking links CallPilot or other voicemail systems at different locations. Digital networking and AMIS Message Networking uses digital networking and Audio Message Interchange Specification (AMIS) to exchange messages. Digital networking Digital networking uses Transmission Control Protocol/Internet Protocol (TCP/IP) to enable the exchange of voice and Fax messages between users at different sites on a network. Note: Any voice message that you use send over the Internet using digital networking can be subject to interception by unauthorized parties. AMIS AMIS provides voice messaging to mailboxes at different sites on a communication network. A network is a collection of offices, locations or sites connected by telecommunication links. Each site on the network must have AMIS to send, receive and reply to network messages. How Message Networking works Sending a message across a network is as easy as sending a message down the hall. There are three ways to send a network message. You can use: • • • a Network Delivery Mailbox Site-Based Addressing Direct Addressing (available for AMIS only) ² Note: Network messages can be composed and sent only from your mailbox. You cannot send a network message by using the Leave Message feature ( ·°‚). CallPilot Message Networking User Guide 4 CallPilot Message Networking User Guide Sending a network message Vancouver CallPilot system Sue Ext 2222 Business Communications Manager or CallPilot 100/150 server Miami CallPilot system Sue’s Mailbox 2222 Mark Ext 4546 Business Communications Manager or CallPilot 100/150 server Mark’s Mailbox 4546 Mark’s Network Delivery Mailbox 7222 Network The diagram Sending a network message shows how messages are sent between different company sites on the same network. In the example, Sue works in the Vancouver office and Mark works in the Miami office. If Sue wants to send Mark a message, she can send the message using Site-Based Addressing, Direct Addressing, or to Mark’s Network Delivery Mailbox. Since Mark has a Network Delivery Mailbox on the local Vancouver system, it is convenient for Sue to send the message to Mark’s Network Delivery Mailbox. Although Mark’s Network Delivery Mailbox appears on the Vancouver system the message is automatically delivered to his mailbox in Miami. The network delivery information, such as the site prefix for the Miami site and Mark’s mailbox number (4546) in Miami, is added to the Network Delivery Mailbox when you create it. Sending a message to a Network Delivery Mailbox is as easy as sending a message to anyone at your site. If Mark wants to send Sue a message, he must use Site-Based Addressing. Sue does not have a Network Delivery Mailbox on the Miami system. Before Mark can send the message he needs to know the site prefix of the Vancouver site and Sue’s mailbox number in Vancouver. The System Administrator can give Mark theVancouver site prefix. After Mark records the message and enters the network delivery information, the network message is automatically delivered to Sue’s mailbox. Note: There is a time limit for the length of AMIS messages. Do not send AMIS messages that are longer than 8 minutes. P0919430 04 CallPilot Message Networking User Guide 5 What you need to know to use Message Networking You must know how to use CallPilot to send messages to mailboxes at other sites. This includes knowing how to open your mailbox, record messages, send messages and retrieve messages. For information about using CallPilot features, refer to the CallPilot Quick Reference Guide for the interface you use, or the CallPilot Reference Guide. To use this guide, you must determine which phone interface you use, and follow the procedures for that interface. For information about determining which interface you use, refer to “Checking which mailbox interface you use” on page 6. CallPilot Message Networking User Guide 6 CallPilot Message Networking User Guide Checking which mailbox interface you use CallPilot supports the Norstar Voice Mail and CallPilot interfaces. Use this procedure to check which mailbox interface you use, then follow the procedures that apply to your interface. ²á¡Ú To check which mailbox interface you use 1 Press . Follow the voice prompts or the display button options to open your mailbox. 2 Check the display to see which interface you use: This is the Norstar Voice Mail interface. 0 new 0 saved PLAY REC ADMIN No messages COMP MBOX EXIT This is the CallPilot interface. 3 P0919430 04 Press ¨ to end the session. CallPilot Message Networking User Guide 7 Sending a message using a Network Delivery Mailbox Network Delivery Mailboxes make it easy to send messages to a mailbox at a remote location. The Network Delivery Mailbox makes sending a message across the country as easy as sending it down the hall. A Network Delivery Mailbox is a pre-programmed direct address to a mailbox at a different site on the network. Each Network Delivery Mailbox has a local mailbox number. The destination site user’s name appears in the company directory. To send a message using a Network Delivery Mailbox, you need the Network Delivery Mailbox number. Ask your System Administrator to give you a list of Network Delivery Mailboxes or create a Network Delivery Mailbox for you. The messages you record must be longer than three seconds. The system times out after five seconds of silence. To send a message using a Network Delivery MailboxNorstar Voice Mail ²á¡Ú 1 . Open your mailbox using Follow the voice prompts or the display button options to open your mailbox. 2 Enter your mailbox password and press OK or 3 Press REC or Record message: 4 At the tone record your message. Record message: RETRY PAUSE OK 5 Press OK or Accept rec? RETRY PLAY 6 Press OK or 7 Enter the Network Delivery Mailbox number. 8 Press SEND to send the message or press OPTS to assign message delivery options: Pswd: OTHR 0 new PLAY RETRY OK 4 saved ADMIN REC OK Mbox: DIR QUIT Miami,sales OPTS CC SEND Will deliver • • Ü £ £ £ . . to end the recording. to accept the recording. for digital destinations, Certified, Urgent, Timed Delivery, or Private. for AMIS destinations, Certified, Urgent, or Timed Delivery, but NOT Private or press CC to send the message to another recipient. 0 new 0 saved PLAY REC ADMIN 9 Press ¨ to end the session. CallPilot Message Networking User Guide 8 CallPilot Message Networking User Guide To send a message using a Network Delivery Mailbox CallPilot No messages COMP MBOX EXIT To: NAME DONE SPEC Empty REC Recording REREC OK ²á¡Ú 1 Open your mailbox using . Follow the voice prompts or the display button options to open your mailbox. 2 Press COMP or 3 Enter the Network Delivery Mailbox number and press DONE or . 4 Press REC or 5 Press OK or when you are done. You can press to add message options: • Will deliver P0919430 04 SEND to open the Compose Message menu. £ Þ £àâ • Rec stopped PLAY DEL àÞ to begin recording. for digital destinations, Certified, Urgent, Timed Delivery, or Private for AMIS destinations, Certified, Urgent, or Timed Delivery, but NOT Private. 6 Press SEND or 7 Press ¨ àá to send the message. to end the session. CallPilot Message Networking User Guide 9 Sending a message using Site-Based Addressing Site-Based Addressing lets you send a message to a mailbox at another location on the network. To use Site-Based Addressing to send a message, you must know the network address of the destination site and the mailbox number of the person you want to send the message to. Ask your System Administrator for a list of destination sites on your network. To send a message using Site-Based Addressing Norstar Voice Mail ²á¡Ú 1 Open your mailbox using . Follow the voice prompts or the display button options to open your mailbox. 0 new 4 saved PLAY REC ADMIN 2 Press REC or ‹. Record message: 3 At the tone, record your message. The message you record must be longer than three seconds. The system times out after five seconds of silence. Record message: RETRY PAUSE OK 4 Press OK or £ to end the recording. Accept rec? RETRY PLAY 5 Press OK or £ to accept the recording. 6 Press Address type? AMIS NETW 7 Press NETW . Network: RETRY 8 Enter the destination site prefix and mailbox number and press OK or . 9 Press SEND to send the message as it is or press OPTS to assign message delivery options: Mbox: DIROPTS CC OK QUIT OK SEND ££ . £ • • for digital destinations, Certified, Urgent, Timed Delivery, or Private. for AMIS destinations, Certified, Urgent, or Timed Delivery, but NOT Private or press CC to send the message to another recipient. Network msg VIEW SEND 0 new 0 saved PLAY REC ADMIN 10 Press SEND to transmit the message. 11 Press ¨ to end the session. CallPilot Message Networking User Guide 10 CallPilot Message Networking User Guide To send a message using Site-Based Addressing CallPilot To: NAME SPEC DONE Site: ²á¡Ú 1 Press . Follow the voice prompts or display options to open your mailbox. 2 Press COMP or 3 Enter the site prefix and the mailbox number and press OK or . 4 The display shows the destination mailbox name and mailbox number. 5 You can enter another address or press DONE or if you are finished entering addresses. 6 Press REC or and record your message at the tone. The message you record must be longer than three seconds. The system times out after five seconds of silence. 7 Press OK or to end your recording or press REREC to erase and re-record your message. You can press to add message options of Urgent, Private, Acknowledged or Timed delivery. 8 Press SEND or àÞ £ to open the Compose Message option. Dest mb: To: NAME SPEC DONE EMPTY REC Recording.... REREC Rec stopped PLAY DEL P0919430 04 OK SEND £ Þ £ àâ àá to send the message. CallPilot Message Networking User Guide 11 Sending a message using Direct Addressing Direct Addressing lets you send a voice message to a mailbox at a different location on a network. To use Direct Addressing you must know the destination site phone number and the mailbox number of the person you want to send a message to. Direct Addressing is available for AMIS only. Ask your System Administrator for the destination site’s phone number and mailbox numbers. ²á¡Ú To send a message using Direct Addressing - Norstar Voice Mail 1 Press . Follow the voice prompts or the display button options to open your mailbox. 2 Enter your mailbox password and press OK or £. 3 Press REC or ‹. Record message: 4 At the tone, record your message. The message you record must be longer than three seconds. The system times out after five seconds of silence. Record message: RETRY PAUSE OK 5 Press OK or £ to end the recording. Accept rec? RETRY PLAY 6 Press OK or £ to accept the recording. 7 Press Address type? NETW AMIS 8 Press AMIS. Ph: RETRY OK ADD 9 Enter the destination site phone number and press OK. Pswd: OTHR RETRY 0 new PLAY REC 4 saved ADMIN Mbox: DIR Destmb: RETRY OK OK QUIT OK ££ . Û to add special 10 Press OK or £ to continue or press ADD or characters. See “Adding special characters” on page 22. Press OK or £ when you are done adding special characters. 11 Enter the destination mailbox number and press OK. OK AMIS msg OPTS CC OTHR 12 Press OTHR to review or send the message or press OPTS to assign message delivery options: • • for digital destinations, Certified, Urgent, Timed Delivery, or Private. for AMIS destinations, Certified, Urgent, or Timed Delivery, but NOT Private or press CC to send the message to another recipient. Network msg VIEW SEND 13 Press SEND to transmit the message. CallPilot Message Networking User Guide 12 CallPilot Message Networking User Guide 0 new 0 saved PLAY REC ADMIN 14 Press ¨ to end the session. To send a message using Direct Addressing CallPilot No messages MBOX COMP EXIT To: NAME CNCL SPEC Dest ph: RETRY OK ADD OK Dest mb: RETRY OK RETRY OK To: NAME SPEC DONE Empty REC Recording... REREC OK Rec stopped PLAY DEL SEND Msg delivered P0919430 04 ²á¡Ú 1 . Open your mailbox using Follow the voice prompts or the display button options to open your mailbox. 2 Press COMP or 3 . This is the default number for special Press SPEC or addressing and can be changed by the System Administrator. 4 Enter the phone number of the remote site and press OK or £. 5 Press OK or £ to continue or press ADD or to add special characters. See “Adding special characters” on page 22. Press OK or £ when you are done adding special characters. 6 Enter the mailbox number at the remote site. 7 Press OK or £ to accept the mailbox number. 8 Press DONE or £ or enter another address to send the message to. 9 to record your message. Press REC or The message you record must be longer than three seconds. The system times out after five seconds of silence. àÞ Úá to open the Compose Message menu. Û Þ 10 Press OK or £ when you are done recording or press REREC or to rerecord your message. You can press to add message options of Urgent, Acknowledged or Timed delivery. ¨ 11 Press SEND or 12 Press Þ àâ àá to send the message. to end the session. CallPilot Message Networking User Guide 13 Replying to network messages You can reply to a network message using the Reply Feature. You must have the network Reply Feature enabled in order to reply to a message. For more information, ask your System Administrator. To reply to a network message Norstar Voice Mail ²á¡Ú 1 Open your mailbox using . Follow the voice prompts or the display button options to open your mailbox. 4 saved ADMIN 2 Press PLAY or to play your new messages or press to listen to your saved messages. End of message REPLY ERASE NEXT 3 After you listen to the message, press REPLY. Reply netwrk msg QUIT MSG 4 Press MSG. If you are replying to a message with more than one recipient, go to step 5. If you are replying to a message with one recipient, go to step 6. Reply to: SNDR 5 If you are replying to a message that has more than one recipient: press SNDR to send your reply only to the sender or press ALL to send your reply to all the people that received the message. Record message: 6 Record your reply message. The message you record must be longer than three seconds. The system times out after five seconds of silence. Record message: RETRY PAUSE OK 7 Press OK to end your recording. Accept rec? RETRY PLAY 8 Press OK to accept your recording. If you are replying to a digital message, go to step 9. If you are replying to an AMIS message, go to step 10. 1 new PLAY REC ALL OK ß Û CallPilot Message Networking User Guide 14 CallPilot Message Networking User Guide Networking OPTS CC 9 SEND Will deliver Press SEND to send the message or press OPTS to assign message delivery options: • • for digital destinations, Certified, Urgent, Timed Delivery, or Private. for AMIS destinations, Certified, Urgent, or Timed Delivery, but NOT Private or press CC to send the message to another recipient. AMIS msg OPTS CC OTHR 10 Press OTHR to go to the next display and review or send the message as it is or press OPTS to assign message delivery options: • • for digital destinations, Certified, Urgent, Timed Delivery, or Private. for AMIS destinations, Certified, Urgent, or Timed Delivery, but NOT Private or press CC to send the message to another recipient. Network msg VIEW SEND 11 Press SEND to transmit the message. End of message REPLY ERASE NEXT 12 Press ¨ to end the session. To reply to a network message CallPilot End message RESP DEL NEXT Respond by REPLY FORW Open your mailbox using . Follow the voice prompts or the display button options to open your mailbox. 2 Press PLAY or to play your new messages or press to listen to your saved messages. 3 After you listen to your messages, press RESP or If you press , go to step 5. 4 Press REPLY or to reply to the message or press FORW or to forward the message or press to reply to all the recipients of the message. ß àÝ P0919430 04 ²á¡Ú 1 Û àÚ àÚ àÜ àÚ . CallPilot Message Networking User Guide Empty REC Recording... REREC OK Þ 5 Press REC or to record a message. The message you record must be longer than three seconds. The system times out after five seconds of silence. 6 Press OK or £ when you are done recording. You can press to add message options: àâ • • Rec stopped PLAY DEL SEND 15 7 Press 8 Press for digital destinations, Certified, Urgent, Timed Delivery, or Private for AMIS destinations, Certified, Urgent, or Timed Delivery, but NOT Private. àá ¨ to send the message. to end the session. CallPilot Message Networking User Guide 16 CallPilot Message Networking User Guide Forwarding a Fax Message using Site-Based Addressing Note: You can send and receive Fax messages only if the Fax option i s available for your system. Ask your System Administrator if you can use Fax on your system. If Fax is available, ask your System Administrator for a list of Fax sites on your network. If the receiving site cannot receive a Fax message, you receive Non Delivery Notification. You can forward a Fax message that you received to a Site-Based Address and add an introductory voice message. The combined voice and Fax message appears as a Fax message in the destination mailbox. You can also forward a received Fax message to a Network Delivery Mailbox. Refer to “Forwarding a Fax Message to a Network Delivery Mailbox” on page 19. When you forward a Fax message, a new cover sheet is added to the original Fax message as part of the new message. However, if the Fax message already has a CallPilot generated Fax cover sheet, it is replaced by a new Fax forward cover sheet. The cover sheet contains: • • • • • the date and time the Fax is created the directory name and telephone number of the sender the telephone number of the recipient the Fax identification (ID) number the number of pages to follow To forward a Fax message using Site-Based Addressing Norstar Voice Mail ²á¡Ú 1 . Open your mailbox using Follow the voice prompts or the display button options to open your mailbox. 2 Enter your mailbox password and press OK or ¥ . Pswd: OTHR RETRY 1 new PLAY 4 saved REC ADMIN 3 to play your new messages Press PLAY or or press to play to your saved messages until you find the Fax message that you want to forward. End of message COPY ERASE NEXT 4 Press COPY or P0919430 04 OK ß Û Þ . CallPilot Message Networking User Guide Ú Ú Û 17 Copy fax MBOX OTHR 5 Press MBOX or Record intro? YES NO 6 to record an introduction to the Fax message Press YES or or press NO or if you do not want to record an introduction to the forwarded Fax message. and go to step 9. The message you record must be longer than three seconds. The system times out after five seconds of silence. Record Message: RETRY PAUSE OK 7 Press OK to end the recording. Accept rec? RETRY PLAY 8 Press OK to accept the recording. 9 Press OK ££ to forward the Fax message. . Address type? NETW AMIS 10 Press NETW. This display appears only if AMIS is enabled. If AMIS is not enabled, the display in step 12 appears. Network RETRY 11 Enter the destination site prefix and the destination mailbox number and press OK. OK OPTS CC SEND Network msg OPTS CC SEND 12 Press SEND to send the message as it is. Press OPTS to assign message delivery options of Certified, Urgent or Timed Delivery. Press CC to send the message to another recipient. 13 Press SEND to send the message now. CallPilot Message Networking User Guide 18 CallPilot Message Networking User Guide To forward a Fax message using Site-Based Addressing CallPilot To: NAME SPEC CNCL Site: ²á¡Ú 1 . Open your mailbox using Follow the voice prompts or the display button options to open your mailbox. 2 to play the current message Press or press to play the next message, until you locate the Fax message you want to forward. 3 Press 4 Enter the destination site prefix and mailbox number and press OK or £. 5 The display shows the destination site name and mailbox number. 6 Press DONE or £. 7 Press REC or 8 Press OK or £. 9 Press SEND or Û ß àÜ to forward the message. Dest mb: To: NAME SPEC DONE Empty REC Recording... REREC OK Rec stopped PLAY DEL SEND P0919430 04 Þ . àá . CallPilot Message Networking User Guide 19 Forwarding a Fax Message to a Network Delivery Mailbox Note: You can send and receive Fax messages only on CallPilot or Business Communications Manager systems that have the Fax option installed. Ask your System Administrator for a list of Fax sites on your network. If the receiving site cannot receive a Fax message, you receive Non Delivery Notification. You can forward a Fax message that you received to a digital networking Network Delivery Mailbox and add an introductory voice message that becomes part of the new message. The message appears as a Fax message in the destination mailbox. You can also forward a received Fax message using Site-Based Addressing. For more information, refer to “Forwarding a Fax Message using Site-Based Addressing” on page 16. A forwarded Fax message has a new cover sheet added to the original Fax message. However, if the Fax message already has a CallPilot-generated Fax cover sheet, it is replaced by the new Fax forward cover sheet. The new cover sheet shows: • • • • • the date and time the Fax was created the directory name and telephone number of the sender the telephone number of the recipient the Fax identification (ID) number the number of pages to follow To forward a Fax message to a Network Delivery Mailbox Norstar Voice Mail Pswd: OTHR RETRY 1 new PLAY 4 saved REC ADMIN ²á¡Ú 1 Open your mailbox using . Follow the voice prompts or the display button options to open your mailbox. 2 Enter your mailbox password and press OK or 3 Press PLAY or or press NEXT or forward. OK End of message COPY ERASE NEXT 4 Press COPY or Û ß Þ ¥ . to play your new messages until you find the Fax message you want to . CallPilot Message Networking User Guide 20 CallPilot Message Networking User Guide Copy fax MBOX Record intro? YES NO Record intro: RETRY OK Accept rec? RETRY PLAY OK Mbox: DIR QUIT Miami,sales OPTS CC SEND Another copy? YES QUIT Ú Ú Û 5 Press MBOX or 6 Press YES or to record an introduction to the Fax message or press NO or if you do not wish to record an introduction to the forwarded Fax message and go to step 9. The message you record must be longer than three seconds. The system times out after five seconds of silence. 7 Press OK to end the recording. 8 Press OK to accept the recording. 9 Enter the Network Delivery Mailbox number. OTHR to forward the Fax message. 10 Press SEND to send the message or press OPTS to assign message delivery options of Certified, Urgent or Timed Delivery or press CC to send the message to another recipient. Miami,sales is an example. The Network Delivery Mailbox name appears in the display. P0919430 04 CallPilot Message Networking User Guide 21 To forward a Fax message to a Network Delivery Mailbox CallPilot To: NAME SPEC CNCL To: NAME SPEC DONE Empty REC Recording... REREC OK Rec stopped PLAY DEL SEND ²á¡Ú 1 Open your mailbox using . Follow the voice prompts or the display button options to open your mailbox. 2 Press to play the current message or press to play the next message, until you locate the Fax message you want to forward. 3 Press 4 Enter the Network Delivery Mailbox number. 5 The display shows the mailbox name. 6 Press DONE or £. 7 to record an introductory voice message. Press REC or The message you record must be longer than three seconds. The system times out after five seconds of silence. 8 Press OK or £. 9 Press SEND or àá . Û ß àÜ to forward the message. Þ CallPilot Message Networking User Guide 22 CallPilot Message Networking User Guide Adding special characters Special characters are pauses or other dialing instructions that you can add if they are required to access the network or a telephone number. Follow the voice prompts or press ADD to add special characters to a telephone number. A telephone number cannot be longer than 30 characters. Note: If you are adding special characters, do not press the dialpad buttons £ to enter a #, or ¥ to enter a *. Press the button directly below the option on a two line display telephone, or listen to the voice prompts for how to enter these characters. Adding special characters to a telephone number Press Û Description or DIGS* Ü or PAUS* to resume adding digits to the destination phone number to enter a timed pause that appears as P on the display. Pauses are four seconds long. to recognize dial tone (behind PBX). The Recognize Dial Tone special character appears as D on the display. Ý Þ( or OTHR #)* to enter a # ß( or OTHR *)* to enter a * TONE* to recognize dial tone (behind PBX). The Recognize Dial Tone special character appears as D on the display. ¥ to cancel and retry *These options are for two line display telephones only. If you use a one line display telephone, use the keypad button shown. P0919430 04
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2002:11:06 13:49:57 Producer : Acrobat Distiller 4.05 for Windows Author : Title : Message Networking User Guide Creator : FrameMaker+SGML 5.5.6p145 Modify Date : 2002:12:11 13:00:45 Page Count : 22 Page Mode : UseOutlinesEXIF Metadata provided by EXIF.tools