Axxess LPZM3 RADIO COMMUNICATIONS MODULE User Manual User s Manual

Axxess Industries Inc. RADIO COMMUNICATIONS MODULE User s Manual

User Manual

TITLE: DATE: REVISION:
19 JUNE 2013
LPZM3 USER’S MANUAL
THIS DRAWING IS THE PROPERTY OF AXXESS INDUSTRIES INC. AND MAY BE NEITHER USED, COPIED, REPRODUCED OR OTHERWISE DEALT WITH NOR ITS CONTENTS COMMUNICATED TO OTHERS EXCEPT IN ACCORDANCE WITH WRITTEN INSTRUCTIONS RECEIVED FROM AXXESS INDUSTRIES INC.
i n d u s t r i e s
103-470 NEAVE COURT
KELOWNA BC CANADA V1V 2M2
1 866 680 2457 WWW.AXXIND.COM
2 JULY 2013
3 JULY 2013
UNITED STATES (FCC)
This equipment complies with Part 15 of the FCC rules and regulations.
To fulfill FCC Certification requirements, an OEM manufacturer must comply with the following
regulations:
1. The modular transmitter must be labelled with its own FCC ID number, and, if the FCC ID is not visible
when the module is installed inside another device, then the outside of the device into which the
module is installed must also display a label referring to the enclosed module. This exterior label can
use wording such as the following:
Example of label required for OEM product containing LPZM3 module
WARNING: The Original Equipment Manufacturer (OEM) must ensure that the OEM modular transmitter
must be labeled with its own FCC ID number. This includes a clearly visible label on the outside of the
final product enclosure that displays the contents shown below. If the FCC ID is not visible when the
equipment is installed inside another device, then the outside of the device into which the equipment is
installed must also display a label referring to the enclosed equipment.
IMPORTANT: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation (FCC 15.19).
The internal / external antenna(s) used for this mobile transmitter must provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.
Contains FCC ID: WP4LPZM3
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(i.) this device may not cause harmful interference and (ii.) this device must accept any interference received,
including interference that may cause undesired operation.
TITLE: DATE: REVISION:
19 JUNE 2013
LPZM3 USER’S MANUAL
THIS DRAWING IS THE PROPERTY OF AXXESS INDUSTRIES INC. AND MAY BE NEITHER USED, COPIED, REPRODUCED OR OTHERWISE DEALT WITH NOR ITS CONTENTS COMMUNICATED TO OTHERS EXCEPT IN ACCORDANCE WITH WRITTEN INSTRUCTIONS RECEIVED FROM AXXESS INDUSTRIES INC.
i n d u s t r i e s
103-470 NEAVE COURT
KELOWNA BC CANADA V1V 2M2
1 866 680 2457 WWW.AXXIND.COM
2 JULY 2013
3 JULY 2013
TITLE: DATE: REVISION:
19 JUNE 2013
LPZM3 USER’S MANUAL
THIS DRAWING IS THE PROPERTY OF AXXESS INDUSTRIES INC. AND MAY BE NEITHER USED, COPIED, REPRODUCED OR OTHERWISE DEALT WITH NOR ITS CONTENTS COMMUNICATED TO OTHERS EXCEPT IN ACCORDANCE WITH WRITTEN INSTRUCTIONS RECEIVED FROM AXXESS INDUSTRIES INC.
i n d u s t r i e s
103-470 NEAVE COURT
KELOWNA BC CANADA V1V 2M2
1 866 680 2457 WWW.AXXIND.COM
2 JULY 2013
CANADA (IC)
Equipment is subject to certification under the applicable RSSs, shall be permanently labelled on each
item, or as an inseparable combination. The label must contain the following information for full
compliance:
For LPZM3 module:
IMPORTANT: This equipment for which a certificate has been issued is not considered certified if it is not
properly labelled. The information on the Canadian label can be combined with the manufacturer's other
labelling requirements
IMPORTANT: Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT: To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for
successful communication.
IMPORTANT: The installer of this radio equipment must ensure that the antenna is located or pointed
such that it does not emit RF field in excess of Health Canada limits for the general population. Consult
Safety Code 6, obtainable from Health Canada's website www.hc-sc.gc.ca/rpb.
Certification Number:
Manufacturer's Name, Trade Name or Brand Name:
Model Name:
IC: 9709A-LPZM3
AXXESS LPZM3 ZRM
LPZM3
3 JULY 2013
EUROPEAN UNION (ETSI)
The LPZM3 Module has been certified for use in European Union countries. If the is incorporated
into a product, the manufacturer must ensure compliance of the final product to the European harmonized EMC
and low-voltage/safety standards. A Declaration of Conformity must be issued for each of these standards and
kept on file as described in Annex II of the R&TTE Directive.
Furthermore, the manufacturer must maintain a copy of the LPZM3 Module documentation
and ensure the final product does not exceed the specified power ratings, antenna
specifications, and/or installation requirements as specified in the user manual. If any of these specifications
are exceeded in the final product, a submission must be made to a notified body for compliance
testing to all required standards.
IMPORTANT: The 'CE' marking must be affixed to a visible location on the OEM product. The CE mark
shall consist of the initials "CE" taking the following form:
LPZM3 Module
If the CE marking is reduced or enlarged, the proportions given in the above graduated drawing must
be respected.
The CE marking must have a height of at least 5mm except where this is not possible on account of
the nature of the apparatus.
The CE marking must be affixed visibly, legibly, and indelibly.
More detailed information about CE marking requirements you can find at "DIRECTIVE
1999/5/EC OF
THE EUROPEAN PARLIAMENT AND OF THE COUNCIL" on 9 March 1999 at section
TITLE: DATE: REVISION:
19 JUNE 2013
LPZM3 USER’S MANUAL
THIS DRAWING IS THE PROPERTY OF AXXESS INDUSTRIES INC. AND MAY BE NEITHER USED, COPIED, REPRODUCED OR OTHERWISE DEALT WITH NOR ITS CONTENTS COMMUNICATED TO OTHERS EXCEPT IN ACCORDANCE WITH WRITTEN INSTRUCTIONS RECEIVED FROM AXXESS INDUSTRIES INC.
i n d u s t r i e s
103-470 NEAVE COURT
KELOWNA BC CANADA V1V 2M2
1 866 680 2457 WWW.AXXIND.COM
2 JULY 2013
3 JULY 2013

Navigation menu