AzureWave Technologies NM383 IEEE 802.11 b/g/n Wireless LAN Module User Manual AW NM383 normal driver User Guide v0 1

AzureWave Technologies, Inc. IEEE 802.11 b/g/n Wireless LAN Module AW NM383 normal driver User Guide v0 1

User Manual.pdf

1AW-NM383IEEE 802.11 b/g/n Wireless LAN ModuleUser GuideVersion 0.1 Documentrelease Date Modification Initials Approved Ver. 0.1 2013/10/07 Initial version Renton Tao Ivan Chen
- 3 - 1. General Description 1-1. Product Overview and Functional Description AzureWave Technologies, Inc. introduces the first IEEE 802.11b/g/n WLAN module Card -AW-NM383. The module is targeted to mobile devices including Personal Digital Assistants (PDAs), Netbook, TV, Tablet and Gaming Device which need small package module, low power consumption, multiple interfaces and OS support. By using AW-NM383, the customers can easily enable the Wi-Fi embedded applications with the benefits of high design flexibility, short development cycle, and quick time-to-market. Compliance with the IEEE 802.11b/g/n standard, the AW-NM383 uses Direct Sequence Spread Spectrum (DSSS), Orthogonal Frequency Division Multiplexing (OFDM), DBPSK, DQPSK, CCK and QAMbaseband modulation technologies. A high level of integration and full implementation of the power management functions specified in the IEEE 802.11 standard minimize the system power requirements by using AW-NM383. In addition to the support of WPA/WPA2 and WEP 64-bit and 128-bit encryption, the AW-NM383 also supports the IEEE 802.11i security standard through the implementation of Advanced Encryption Standard (AES)/Counter Mode CBC-MAC Protocol (CCMP), Wired Equivalent Privacy (WEP) with Temporal Key Integrity Protocol (TKIP), Advanced Encryption Standard (AES)/Cipher-Based Message Authentication Code (CMAC), and WLAN Authentication and Privacy Infrastructure (WAPI) security mechanisms. For the video, voice and multimedia applications the AW-NM383 support 802.11e Quality of Service (QoS). The AW-NM383 supports SDIO for WLAN to the host processor. AW-NM383 is suitable for multiple mobile processors for different applications. With the support cellular phone co-existence, the AW-NM383 is also the best solution for mobile phones and PDA phones applications. AW-NM383 module adopts Marvell’s latest highly-integrated WLAN SoC---88W8782. All the other components are implemented by all means to reach the mechanical specification required.
1-2. Key Features Small footprint: 35mm(L) x 4SDIO interfaces support for WCellular phone co-existence sMultiple power saving modesIEEE 802.11i for advanced seQuality of Service (QoS) suppDrip-in WLAN Linux driversSupport for Linux kernel verSupport for BlueZ v4.47 BlueSimultaneous AP-STASupport China WAPI Lead-free design 1-3. Block Diagram - 4 - 40mm(W) x 5 mm(H) WLANupports for low power consumptionecurityport for multimedia applicationss are Android ready and validated on Andrsions up to 2.6.32. etooth profiles stack used in Android Éclairoid based systems.r.
- 5 - 2. Specifications Table Product Description Wireless LAN Module Card WLAN Standard IEEE 802.11b/g/n, Wi-Fi compliant Host Interface SDIO / G-SPI for WLAN Major ChipsetMarvell 8782 Dimension 40mm x 35mm x 5.0mm Operating Conditions Voltage 3.3V +/- 10%, 1.8V +/- 10% Temperature Operating: -20 ~ 70oC ; Storage: -40 ~ 85oC Electrical Specifications Frequency Range 2.4 GHz ISM radio band Number of Channels 802.11b: USA, Canada and Taiwan – 11 Most European Countries – 13 France – 4, Japan – 14 802.11g: USA, Canada and Taiwan – 11 Most European Countries – 13 Japan – 13 802.11n(HT20): Channel 1~13(2412~2472) 802.11n(HT40): Channel 3~11(2422~2462) Modulation DSSS, OFDM, DBPSK, DQPSK, CCK, 16-QAM, 64-QAM for WLAN Antenna 1 antenna for WLAN Medium Access Protocol CSMA/CA with ACK Data Rates WLAN 802.11b: 1, 2, 5.5, 11Mbps 802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11n MCS0-7 up to 150Mbps Security WAPI WEP 64-bit and 128-bit encryption with H/W TKIP processing WPA/WPA2 (Wi-Fi Protected Access) AES-CCMP hardware implementation as part of 802.11i security standard
2Step1: Power on notebook PC and choose Ubuntu OS. Step2: Plug in USB cable to connect DUT and notebook PC. Step3: Open terminal and key in commands. Password is “000000”.
3Step4: Select below interface and connect to your AP.You can do further RF set up by using command “iwconfig”. Ex. sudo iwconfig –h. You can see how to set up by different commands.
- 12 - 2-4. SDIO Host Interface Specifications Referred from Marvell hardware specifications SDIO Protocol Timing Diagram SDIO Protocol Timing Diagram—High Speed Mode Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that maycause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void theuser's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipmentshould be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: TLZ-NM383”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
- 13 - 3. Dimension: TBC 4. Pin Definition Pin Assignment Pin No Definition Basic Description Type 1 PDn )XOO3RZHU'RZQDFWLYHORZ IXOOSRZHUGRZQPRGH QRUPDOPRGHConnect to power down pin of host or 1.8V External host required to drive this pin high for normal operation No internal pull-up on this pin I 2 VIO +3.3V power supply P 3 GND 4 SD_CLK SDIO 4-bit Mode: Clock Input SDIO 1-bit Mode: Clock Input SDIO SPI Mode: Clock Input I 5 GND 6 SD_D3 SDIO 4-bit Mode: Data line bit[3] SDIO 1-bit Mode: Reserved SDIO SPI Mode: Card Select(active low) I/O 7 SD_D2 SDIO4-bit Mode: Data line bit[2]or Read Wait(optional) SDIO 1-bit Mode: Read Wait(optional) SDIO SPI Mode: Reserved I/O 8 SD_D1 SDIO 4-bit Mode: Data line bit[1] SDIO 1-bit Mode: Interrupt SDIO SPI Mode: Reserved I/O 9 SD_D0 SDIO 4-bit Mode: Data line bit[0] SDIO 1-bit Mode: Data line SDIO SPI Mode: Data output I/O 10 SD_CMD SDIO 4-bit Mode: Command/Response SDIO 1-bit Mode: Command Line SDIO SPI Mode: Data Input I 11 GND 12 VCC +3.3V power supply P 13 GPIO[2] Host Wakeup: SoC-to-Host Wakeup (output) O 5. Mechanical Characteristic 5.1 TBC Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment shouldbe installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé.Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votrecorps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is stillresponsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires.Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformitésupplémentaires requis pour ce module installé. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with anothertransmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product.In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter)and obtaining a separate Canada authorization. NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.
- 14 - End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may bemaintained between the antenna and users. The final end product must be labeled in a visible area with the following:“Contains IC: 6100A-NM383”. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée detelle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit êtreétiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6100A-NM383". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove thisRF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installerou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements commeindiquͼ dans ce manuel. եф౗ႝݢᒟ৔܄ႝᐒᆅ౛ᒤݤ!ಃΜΒచ ࿶ࠠԄᇡ᛾ӝ਱ϐեф౗৔ᓎႝᐒǴߚ࿶೚ёǴϦљǵ୘ဦ܈٬Ҕޣ֡όளᏰԾᡂ׳ᓎ౗ǵуεф౗܈ᡂ׳চ೛ीϐ੝܄ϷфૈǶ!ಃΜѤచ եф౗৔ᓎႝᐒϐ٬Ҕόளቹៜ०ૐӼӄϷυᘋӝݤ೯ߞǹ࿶ว౜Ԗυᘋ౜ຝਔǴᔈҥջଶҔǴ٠ׯ๓ԿคυᘋਔБளᝩុ٬ҔǶ!߻໨ӝݤ೯ߞǴࡰ٩ႝߞݤೕۓբ཰ϐคጕႝ೯ߞǶ!եф౗৔ᓎႝᐒ໪הڙӝݤ೯ߞ܈π཰ǵࣽᏢϷᙴᕍҔႝݢᒟ৔܄ႝᐒ೛ഢϐυᘋǶ!

Navigation menu