AzureWave Technologies NM383 IEEE 802.11 b/g/n Wireless LAN Module User Manual AW NM383 normal driver User Guide v0 1

Download:
Mirror Download [FCC.gov]
Document ID	2124628
Application ID	zXHSXHRbO5ujAtIoMhkEHA==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	298.07kB (3725847 bits)
Date Submitted	2013-11-21 00:00:00
Date Available	2014-05-10 00:00:00
Creation Date	2013-11-20 14:13:21
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2013-11-20 14:38:06
Document Title	AW-NM383 normal driver User Guide v0 1
Document Creator	PScript5.dll Version 5.2
Document Author:	eden

AW-NM383
IEEE 802.11 b/g/n Wireless LAN Module
User Guide
Version 0.1
Document
release
Date
Ver. 0.1
2013/10/07
Modification
Initial version
Initials
Approved
Renton Tao
Ivan Chen
1. General Description
1-1.
Product Overview and Functional Description
AzureWave Technologies, Inc. introduces the first IEEE 802.11b/g/n WLAN module Card
-AW-NM383. The module is targeted to mobile devices including Personal Digital Assistants (PDAs),
Netbook, TV, Tablet and Gaming Device which need small package module, low power consumption,
multiple interfaces and OS support. By using AW-NM383, the customers can easily enable the Wi-Fi
embedded applications with the benefits of high design flexibility, short development cycle, and quick
time-to-market.
Compliance with the IEEE 802.11b/g/n standard, the AW-NM383 uses Direct Sequence Spread Spectrum
(DSSS), Orthogonal Frequency Division Multiplexing (OFDM), DBPSK, DQPSK, CCK and QAM
baseband modulation technologies. A high level of integration and full implementation of the power
management functions specified in the IEEE 802.11 standard minimize the system power requirements by
using AW-NM383. In addition to the support of WPA/WPA2 and WEP 64-bit and 128-bit encryption,
the AW-NM383 also supports the IEEE 802.11i security standard through the implementation of
Advanced Encryption Standard (AES)/Counter Mode CBC-MAC Protocol (CCMP), Wired
Equivalent Privacy (WEP) with Temporal Key Integrity Protocol (TKIP), Advanced Encryption
Standard (AES)/Cipher-Based Message Authentication Code (CMAC), and WLAN Authentication and
Privacy Infrastructure (WAPI) security mechanisms.
For the video, voice and multimedia applications the AW-NM383 support 802.11e Quality of Service
(QoS).
The AW-NM383 supports SDIO for WLAN to the host processor.
AW-NM383 is suitable for multiple mobile processors for different applications. With the support
cellular phone co-existence, the AW-NM383 is also the best solution for mobile phones and PDA
phones applications.
AW-NM383 module adopts Marvell’s latest highly-integrated WLAN SoC---88W8782. All the other
components are implemented by all means to reach the mechanical specification required.
-3-
1-2.
Key Features
Small footprint: 35mm(L) x 40mm(W)
x 5 mm(H)
SDIO interfaces support for WLAN
Cellular phone co-existence support
Multiple power saving modess for low power consumption
IEEE 802.11i for advanced seecurity
Quality of Service (QoS) supp
port for multimedia applications
Drip-in WLAN Linux driverss are Android ready and validated on Android based systems.
Support for Linux kernel verrsions up to 2.6.32.
Support for BlueZ v4.47 Blueetooth profiles stack used in Android Éclair.
Simultaneous AP-STA
Support China WAPI
Lead-free design
1-3.
Block Diagram
-4-
2. Specifications Table
Product Description
Wireless LAN Module Card
WLAN Standard
IEEE 802.11b/g/n, Wi-Fi compliant
Host Interface
SDIO / G-SPI for WLAN
Major Chipset
Marvell 8782
Dimension
40mm x 35mm x 5.0mm
Operating Conditions
Voltage
3.3V +/- 10%, 1.8V +/- 10%
Temperature
Operating: -20 ~ 70oC ; Storage: -40 ~ 85oC
Electrical Specifications
Frequency Range
2.4 GHz ISM radio band
802.11b: USA, Canada and Taiwan – 11
Most European Countries – 13
France – 4, Japan – 14
802.11g: USA, Canada and Taiwan – 11
Number of Channels
Most European Countries – 13
Japan – 13
802.11n(HT20): Channel 1~13(2412~2472)
802.11n(HT40): Channel 3~11(2422~2462)
Modulation
DSSS, OFDM, DBPSK, DQPSK, CCK, 16-QAM, 64-QAM for WLAN
Antenna
1 antenna for WLAN
Medium Access Protocol
CSMA/CA with ACK
WLAN
802.11b: 1, 2, 5.5, 11Mbps
Data Rates
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11n MCS0-7 up to 150Mbps
Security
WAPI
WEP 64-bit and 128-bit encryption with H/W TKIP processing
WPA/WPA2 (Wi-Fi Protected Access)
AES-CCMP hardware implementation as part of 802.11i security
standard
-5-
Step1: Power on notebook PC and choose Ubuntu OS.
Step2: Plug in USB cable to connect DUT and notebook PC.
Step3: Open terminal and key in commands. Password is “000000”.
Step4: Select below interface and connect to your AP.
You can do further RF set up by using command “iwconfig”.
Ex. sudo iwconfig –h.
You can see how to set up by different commands.
Federal Communication Commission Interference Statement
2-4. SDIO Host Interface Specifications
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
Referred from Marvell hardware specifications
cause undesired operation.
SDIO Protocol Timing Diagram
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
SDIO Protocol
Diagram—High Speed Mode
Radiation
ExposureTiming
Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on
the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including
the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be
maintained between the antenna and users. The final end product must be labeled in a visible area with the following:
“Contains FCC ID: TLZ-NM383”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF
module in the user's manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
- 12 -
Industry Canada statement:
3. Dimension:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
TBC
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son
fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et
(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement
indésirable.
4. Pin Definition
Radiation Exposure Statement:
ThisPin
equipment
complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should
Assignment
be installed and operated with minimum distance 20cm between the radiator & your body.
Pin No
Definition
Basic Description
Type
)XOO3RZHU'RZQ DFWLYHORZ 
Déclaration d'exposition aux radiations:
IXOOSRZHUGRZQPRGH
Cet équipement est conforme auxlimites
d'exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet 1équipementPDn
doit être installé et
avec un minimum de 20 cm de distance entre la source
 utilisé
QRUPDOPRGH
I de rayonnement et votre
corps.
Connect to power down pin of host or 1.8V
External
host required
drivefollowing
this pin highconditions:
for normal operation
This device is intended only for OEM
integrators
undertothe
(For module device use)
No internal pull-up on this pin
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2 transmitter
VIO module may not+3.3V
power supply
2) The
be co-located
with any other transmitter or antenna.
GND
As long as 2 conditions above areSDIO
met,4-bit
further
transmitter test will not be required. However, the OEM integrator is still
Mode: Clock Input
responsible
for
testing
their
end-product
for
any
additional
SD_CLK
SDIO 1-bit Mode: Clock Inputcompliance requirements required withI this module installed.
SDIO SPI Mode: Clock Input
Cet 5appareil est
conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de
GND
dispositif module)
SDIO 4-bit Mode: Data line bit[3]
SD_D3
SDIOsorte
1-bit Mode:
1) L'antenne
doit
être installée de telle
qu'uneReserved
distance de 20 cm est respectée entre l'antenneI/O
et les utilisateurs, et
SDIO
SPI
Mode:
Card
Select(active
low)
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
SDIO4-bit Mode: Data line bit[2]or Read Wait(optional)
SDIO 1-bit Mode: Read Wait(optional)
I/O
Tant que les 2 conditions ci-dessus
remplies,
des essais supplémentaires sur l'émetteur ne seront pas nécessaires.
SDIOsont
SPI Mode:
Reserved
Toutefois, l'intégrateur OEM est toujours
desbit[1]
essais sur son produit final pour toutes exigences de conformité
SDIO 4-bitresponsable
Mode: Data line
SD_D1
SDIO 1-bit
Mode: Interrupt
I/O
supplémentaires
requis pour ce module
installé.
SDIO SPI Mode: Reserved
SDIO 4-bit Mode: Data line bit[0]
IMPORTANT
NOTE:
SD_D0
SDIO 1-bit Mode: Data line
I/O
In the event that these conditionsSDIO
can SPI
notMode:
be met
example certain laptop configurations or co-location with another
Data(for
output
SDIO 4-bit is
Mode:
Command/Response
transmitter), then the Canada authorization
no longer
considered valid and the IC ID can not be used on the final product.
10 circumstances,
SD_CMD the OEM SDIO
1-bit Mode:
Command
Line for re-evaluating the end productI (including the transmitter)
In these
integrator
will be
responsible
SDIO SPI Mode: Data Input
SD_D2
and obtaining a separate Canada authorization.
11
GND
NOTE
IMPORTANTE:
Dans12le cas où VCC
ces conditions ne peuvent
être supply
satisfaites (par exemple pour certaines configurations
+3.3V power
P d'ordinateur portable ou
de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne
13
GPIO[2]
Host Wakeup: SoC-to-Host Wakeup (output)
peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final
(y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.
5. Mechanical Characteristic
5.1
TBC
- 13 -
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be
maintained between the antenna and users. The final end product must be labeled in a visible area with the following:
“Contains IC: 6100A-NM383”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de
telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être
étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6100A-NM383".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this
RF module in the user's manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer
ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme
indiquͼ dans ce manuel.
եф౗ႝ‫ݢ‬ᒟ৔‫܄‬ႝᐒᆅ౛ᒤ‫!ݤ‬
ಃΜΒచ ࿶ࠠԄᇡ᛾ӝ਱ϐեф౗৔ᓎႝᐒǴߚ࿶೚ёǴϦљǵ୘ဦ‫܈‬٬Ҕ‫֡ޣ‬όளᏰԾᡂ‫׳‬ᓎ౗ǵуεф౗
‫܈‬ᡂ‫׳‬চ೛ीϐ੝‫܄‬ϷфૈǶ!
ಃΜѤచ եф౗৔ᓎႝᐒϐ٬Ҕόளቹៜ०ૐӼӄϷυᘋӝ‫ݤ‬೯ߞǹ࿶ว౜Ԗυᘋ౜ຝਔǴᔈҥջଶҔǴ٠‫ׯ‬
๓ԿคυᘋਔБளᝩុ٬ҔǶ!
߻໨ӝ‫ݤ‬೯ߞǴࡰ٩ႝߞ‫ݤ‬ೕ‫ۓ‬բ཰ϐคጕႝ೯ߞǶ!
եф౗৔ᓎႝᐒ໪‫ڙה‬ӝ‫ݤ‬೯ߞ‫܈‬π཰ǵࣽᏢϷᙴᕍҔႝ‫ݢ‬ᒟ৔‫܄‬ႝᐒ೛ഢϐυᘋǶ!
- 14 -

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2013:11:20 14:38:06+08:00
Create Date                     : 2013:11:20 14:13:21+08:00
Metadata Date                   : 2013:11:20 14:38:06+08:00
Format                          : application/pdf
Title                           : AW-NM383 normal driver User Guide v0 1
Creator                         : eden
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:193aec9e-aac7-4fa2-aaeb-3f4638804a2c
Instance ID                     : uuid:f1cbcecd-e626-4301-aa94-acabd7975235
Page Count                      : 9
Author                          : eden

EXIF Metadata provided by EXIF.tools