AzureWave Technologies NU706 802.11 b/g/n Wireless USB Mini card User Manual AW NU706H

Download:
Mirror Download [FCC.gov]
Document ID	1028332
Application ID	5XRLUDOkMH0H4pTndZbBQw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	121.46kB (1518228 bits)
Date Submitted	2008-11-10 00:00:00
Date Available	2008-11-10 00:00:00
Creation Date	2008-10-23 17:10:08
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2008-10-23 17:10:08
Document Title	AW-NU706H User Manual.pdf
Document Creator	PScript5.dll Version 5.2.2
Document Author:	gina_lo

AW-NU706H / AW-NU706
802.11 b/g/n Wireless USB Mini card
I. Introduction
i. Overview
AzureWave Technologies, Inc. introduces the pioneer of the IEEE 802.11b/g/n USB Half-Mini-Card
wireless module ---AW-NU706. The AW-NU706 USB Half-Mini-Card wireless module is a highly
integrated wireless local area network (WLAN) solution to let users enjoy the digital content through
the latest wireless technology without using the extra cables and cords. It enables a high
performance, cost effective, low power, compact solution that easily fits onto one side of a USB
Half-Mini-Card.
Compliant with the IEEE 802.11b/g/n standard, the AW-NU706 uses Direct Sequence Spread
Spectrum (DSSS), Orthogonal Frequency Division Multiplexing (OFDM), BPSK, QPSK, CCK and
QAM baseband modulation technologies.
A high level of integration and full implementation of the power management functions specified in
the IEEE 802.11 standard minimize system power requirements by using AW-NU706.
Longer Range and Faster Speed
Comparing to 802.11g technology, 802.11n draft 3.0 standard make big improvement on speed and
range. It Increases wireless range by up to 2 times and reduces dead spots in coverage area. The
data rate can up to 150Mbps data rate.
ii. Features
z
USB Half-Mini-Card.
z
Compliant with IEEE802.11n Draft 3.0 standard
z
2 antennas to support 1(Transmit) u 1(Receive) Diversity technology
z
High speed wireless connection up to 150MbpsLow power consumption and high
performance
z
Enhanced wireless security
iii. Product Review
1. Connection Mode
ʳ
Ϩ˜́˹̅˴̆̇̅̈˶̇̈̅˸ʳˠ̂˷˸ʳ
ʳ
˜́˹̅˴̆̇̅̈˶̇̈̅˸ʳ̀̂˷˸ʳ́˸˸˷̆ʳ˴́ʳ˴˶˶˸̆̆ʳ̃̂˼́̇ʳ̇̂ʳ˸̆̇˴˵˿˼̆˻ʳ̇˻˸ʳ́˸̇̊̂̅˾ʿʳ̊˻˼˶˻ʳ˶˴́ʳ̃̅̂̉˼˷˸ʳ̊˼̅˸˿˸̆̆ʳ˴˶˶˸̆̆˸̆ʳ
̊˼̇˻˼́ʳ̉˴˿˼˷ʳ̅˴́˺˸ʳ˹̂̅ʳ̈̆˸̅̆ʳ̇̂ʳ˶̂̀̀̈́˼˶˴̇˸ʳ̊˼̇˻ʳ̂̇˻˸̅̆ʳ̂̅ʳ̇̅˴́̆̀˼̇ʳ˷˴̇˴ʳ̊˼̇˻ʳ˴ʳ̊˼̅˸˷ʳ́˸̇̊̂̅˾ˁʳ˧˻˸̅˸ʳ˴̅˸ʳ
̆˸̉˸̅˴˿ʳ˵˸́˸˹˼̇̆ʳ̂˹ʳ˜́˹̅˴̆̇̅̈˶̇̈̅˸ʳ́˸̇̊̂̅˾˼́˺ˍʳ
ʳ
¥ Roaming: a wireless LAN enabled computer can physically move from the operating range of one
access point to the other without losing connection. There is a quick association made between new
access point and wireless device as the computer traverses from the coverage of one access point to
another.ʳ
¥ Range Extension: each wireless LAN enabled computer within the range of access point can
communicate with other wireless LAN enabled computers within the ˸˹˹˸˶̇˼̉˸ range from the access
point.
¥ Wired to wireless LAN connection: the access point will establish a bridge between wireless LAN
and other wired counterparts.
ʳ
Infrastructure Mode
Ϩ˔˷ˀ˻̂˶ʳˠ̂˷˸ʳ
ʳ
˧˻˸ʳ˷˼˹˹˸̅˸́˶˸ʳ˵˸̇̊˸˸́ʳ˔˷ˀ˻̂˶ʳ̀̂˷˸ʳ˴́˷ʳ˜́˹̅˴̆̇̅̈˶̇̈̅˸ʳ̀̂˷˸ʳ˼̆ʳ̇˻˴̇ʳ˔˷ˀ˻̂˶ʳ̀̂˷˸ʳ˷̂˸̆ʳ́̂̇ʳ́˸˸˷ʳ̇˻˸ʳ
˴˶˶˸̆̆ʳ̃̂˼́̇ʳ̂̅ʳ̅̂̈̇˸̅ˁʳ˪˻˸́ʳ̌̂̈ʳ̈̆˸ʳ̇˻˼̆ʳ̀̂˷˸ʿʳ̌̂̈̅ʳ˶̂̀̃̈̇˸̅ʳ̊˼˿˿ʳ˴˶̇ʳ˴̆ʳ˴ʳ̆˸̅̉˸̅ʳ̊˼̇˻˼́ʳ̇˻˸ʳ̉˴˿˼˷ʳ̅˴́˺˸ʳ
˴́˷ʳ˶̂́́˸˶̇ʳ˷˼̅˸˶̇˿̌ʳ̇̂ʳ̂̇˻˸̅̆ʳ˼́ʳ̇˻˸ʳ̆˴̀˸ʳ˟˔ˡʳ̊̂̅˾˺̅̂̈̃ˁʳ
ʳ
ʳ
Ad-hoc Mode
It is recommended to choose this mode when there is no access point showed on your wireless
network.
II. Installation
i.
System Requirements
*Minimum of 64MB system memory
*Operating system: XP/Vista
* Driver installation
ii. Setup: Windows XP OS
1. Find out the Driver, and launch the Setup Wizard
2. Please wait few seconds for wizard to prepare installation
3. Please select click [Install] to proceed
4. The Wizard is running installation
5. Please wait few seconds for Wizard to setup
6. When it is completed, please click [Finish]
iii. Setup: Windows Vista OS
Please follow the steps to complete installation.
1. Launch the setup driver
2. When you see the permission dialogue box, please click [Continue]
3. Now the Wizard is preparing installation
4. Please click [Install] to proceed
5. The system is processing installation
10
6. Please wait few seconds for Wizard to setup
7. When the setup is completed, please click [Finish]
11
III. Network Connection
i. For Windows XP OS
Please see the following steps to setup network connection for Windows XP.
1. Find the network icon on the desktop shortcut and right-click on it. Choose “View Available
Wireless networks”
2. You will see several options, please select one and click [Connect]
12
3. Please wait for few seconds to let system connecting to selected wireless network
4. You may need to type the network key when it is required (if the network doesn’t request the key,
the network will connect directly.)
5. Now the selected wireless network is connected
13
6. You can check the connection status by clicking [Status] in the pop-up dialogue
7. Here is the wireless network connection status
ii. For Windows Vista OS
Following are the instructions to setup wireless connection for Windows Vista.
1. Right-click on the network icon located on desktop shortcut. When you see the dialogue, please
click [Connect to a network]
14
2. Choose wireless network within your range and click [Connect]
* If selected network is not secure, please choose [Connect anyway]
3. You may need to wait for few seconds when Windows connects to wireless network
15
4. Now the selected wireless network is connected
5. If you want to see the connection status, please right-click on the network you choose and select
[Status]
16
6. This is the information of network status
17
IV. Setup for Ad-hoc Mode
i. For Windows XP OS
If you want to choose Ad-hoc mode, please right-click network icon on desktop shortcut and choose
“Open Network Connections”, or go to [Control Panel] and double-click “Network Connection”
icon.
When you see the “Network Connections” screen, please follow the steps below to setup Ad-hoc
mode.
18
1. Double-click “Wireless Network Connection” icon to enter its properties
2. Click "General” tab and double-click the “Internet Protocol (TCP/IP)” item
19
3. Choose “Use the following IP address:” and type the IP address; then click [OK]
*Note: the IP address of the other wireless card should be set with the same subnet mask
4. Right-click the “Wireless Network Connection” icon and choose “properties”
20
5. Select “Wireless Network” tab and choose [Add]
6. Type “Network name (SSID)” and choose “Data encryption” if you want to protect the network
security
7. When you see the dialogue showing your network is unsecured, please click [Continue Anyway]
21
8. Now your network is in Ad-hoc mode
ii. For Windows Vista OS
Please follow the steps to setup Ad-hoc mode for Windows Vista.
1. Right-click the Network neighbor to choose “properties,” or you can right-click network icon on
desktop shortcut and choose “Network and Sharing Center”
22
2. When you see the “Network and Sharing Center” windows, please select “Manage network
connection” bar
23
3. Right-click the connected network icon and choose “Properties”
4. When you see the warning message, please click [Continue]
24
5. Choose “Networking” tab and double-click the “Internet Protocol Version 4 (TCP/IPv4)” item
6. Choose “Use the following IP address:” and type the IP address; then click [OK]
*Note: the IP address of the other wireless card should be set with the same subnet mask
25
7. Choose “Manage wireless networks” bar
8. Select [Add]
26
9. Choose “Create ad-hoc network”
10. Please click [Next]
27
11. Enter “Network name” and if you want to protect the network security, please choose in
“security type”; then click [Next]
12. Now your network is in Ad-hoc mode
28
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test
methods have been applied in order to prove presumption of conformity with the essential requirements of
the R&TTE Directive 1999/5/EC:
EN 60950-1: 2006
Safety of Information Technology Equipment
EN50371
EN 300 328 V1.7.1: (2006-10)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems;
Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation
techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive
EN 301 489-1 V1.6.1: (2005-09)
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility
(EMC) standard for radio equipment and services; Part 1: Common technical requirements
EN 301 489-17 V1.2.1 (2002-08)
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility
(EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband
transmission systems and 5 GHz high performance RLAN equipment
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member
states and EFTA countries, except in France and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain
authorization to use the device for setting up outdoor radio links and/or for supplying public access to
telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output
power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed
information the end-user should contact the national spectrum authority in France.
0560
Ɣ Switch off the radio components (Bluetooth or wireless LAN) on the device when you are in a
29
hospital, an operating room or near a medical electronics system. The transmitted radio waves
can impair the operation of the medical devices.
Ɣ Keep the device at least 20 cm from a pacemaker, as otherwise the proper operation of the
pacemaker may be impaired by radio waves.
Ɣ The transmitted radio waves can cause an unpleasant humming in hearing aids.
Ɣ Switch off the device when you are in an aircraft or driving in a car.
Ɣ Do not let the device near flammable gases or into hazardous environments (e.g. paintshops)
with radio components switched on, as the transmitted radio waves can cause an explosion or
a fire.
ýesky
[Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zaĜízení] je ve shodČ se základními
požadavky a dalšími pĜíslušnými ustanoveními smČrnice 1999/5/ES.
Dansk
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets
[Danish]
typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen
Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type
of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
English
Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance
with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo]
cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE.
ǼȜȜȘȞȚțȒ
[Greek]
ȂǼ ȉǾȃ ȆǹȇȅȊȈǹ [name of manufacturer] ǻǾȁȍȃǼǿ ȅȉǿ [type of equipment]
ȈȊȂȂȅȇĭȍȃǼȉǹǿ ȆȇȅȈ ȉǿȈ ȅȊȈǿȍǻǼǿȈ ǹȆǹǿȉǾȈǼǿȈ Ȁǹǿ ȉǿȈ ȁȅǿȆǼȈ
ȈȋǼȉǿȀǼȈ ǻǿǹȉǹȄǼǿȈ ȉǾȈ ȅǻǾīǿǹȈ 1999/5/ǼȀ.
Français
[French]
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme
aux exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Latviski
[Latvian]
Ar šo [name of manufacturer / izgatavotƗja nosaukums] deklarƝ, ka [type of equipment /
iekƗrtas tips] atbilst DirektƯvas 1999/5/EK bnjtiskajƗm prasƯbƗm un citiem ar to
saistƯtajiem noteikumiem.
30
Lietuviǐ
[Lithuanian]
Nederlands
[Dutch]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van
richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma
mal-ƫtiƥijiet essenzjali u ma provvedimenti oƫrajn relevanti li hemm fid-Dirrettiva
1999/5/EC.
Magyar
[Hungarian]
Polski
[Polish]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Niniejszym [nazwa producenta] oĞwiadcza, Īe [nazwa wyrobu] jest zgodny z
zasadniczymi wymogami oraz pozostaáymi stosownymi postanowieniami Dyrektywy
1999/5/EC.
Português
[Portuguese]
Slovensko
[Slovenian]
Slovensky
[Slovak]
Suomi
[Finnish]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os
requisitos essenciais e outras disposições da Directiva 1999/5/CE.
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in
ostalimi relevantnimi doloþili direktive 1999/5/ES.
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĎĖa základné požiadavky a všetky
príslušné ustanovenia Smernice 1999/5/ES.
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen
tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
Countries:
Austria, Belgium, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Slovenia, Slovak, Spain, Bulgaria, Czech Republic,
Switzerland, Sweden & UK.
31
This device is intended only for OEM integrators under the following
conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The antenna should be integral if the end device is intended to be operated
in 5.15 ~ 5.25GHz frequency range.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed (for example, digital device emissions, PC peripheral
requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator
will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users (for example Access Point ,Router). The final end product must be
labeled in a visible area with the following: “Contains TX FCC ID:
TLZ-NU706
NI3-MP86005001Manual
Information That Must be Included
The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module in the users manual of
the end product which integrate this module.
The users manual for OEM integrators end users must include the following
information in a prominent location “ IMPORTANT NOTE: To comply with FCC
RF exposure compliance requirements, the antenna used for this transmitter
must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other
antenna or transmitter” .
If the end product integrating this module is going to be operated in 5.15 ~
5.25GHz frequency range, the warning statement in the user manual of the
end product should include the restriction of operating this device in indoor
could void the user’s authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2008:10:23 17:10:08+08:00
Modify Date                     : 2008:10:23 17:10:08+08:00
Page Count                      : 33
Creation Date                   : 2008:10:23 09:10:08Z
Mod Date                        : 2008:10:23 09:10:08Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : gina_lo
Metadata Date                   : 2008:10:23 09:10:08Z
Creator                         : gina_lo
Title                           : AW-NU706H User Manual.pdf

EXIF Metadata provided by EXIF.tools