B LINK ELECTRONIC BL-LW0XX Mobile Verifier 3 User Manual TX LW05 2M1

B-LINK ELECTRONIC LIMITED Mobile Verifier 3 TX LW05 2M1

Users Manual

深 圳 必 联 电 子 有 限 公 司 SHENZHEN B-LINK ELECTRONICS CO.,LTD. IEEE 802.11 b/g/n WiFi Module Model: BL-LWXX Series Revision:7A Date:2011.08.06 TEL：+86-0755-28023453 FAX:+86-0755-28029002 EMAIL:he@lefen.net http://www.b-link.net.cn ADD: NO 37,FuQian Rd, JuTang Community,GuanLan town BaoAn district,ShenZhen, 518110,China
1: Introduction: BL-LWXX Serives product is a low power, high linear output power, in line with IEEE802.11B / G /N standard, IEEE 802.11i security protocol support, and the standard IEEE 802.11e quality of service 150M USB wireless card, with other meet the standard of wireless devices interconnected, supporting the latest WEP 64/128 bit data encryption, support WPA-PSK/WPA2-PSK, WPA/WPA2 security, wireless transmission rates of up to 150M, 11G is the product of 3 times normal, the All the smart set high gain antenna, can adapt to different working environment, desktop or notebook computer users, and other wireless networking devices need to achieve easy access to the wireless network. 2: Application: Wireless Internet, network cameras, set-top box GPS, hard disk player, wireless networking equipment and other needs 3: product Features Project Description Supported protocols and standards IEEE 802.11N IEEE 802.11G, IEEE 802.11B CSMA/CA ACK Bus Interface USB1.1 USB2.0 Frequency range 2.4-2.4835GHZ Data modulation 14 Data modulation OFDM/DBPSK/DQPSK/CCK Mode Infrastructure or Ad-Hoc Transmission rate 150/54/48/36/24/18/12/9/6/5.5/2/1M Sensitivity @PER 54/150M:-72dBm@10%PER,11M:-85dBm@8%PER 6M: -88dBm@10%PER , 1M: -90dBm@8%PER Transmit power 54M/150M:15DBM, 11M:19DBM Antenna gain 2dbi LED Instructions Status Indicator Transmission distance Indoor up to 100m, outdoor up to 300 meters (depends on the environments Operating System Support WIN2000/XP/VISTA/LINUX/WINCE/WIN7 Operating voltage DC 5V +-0.2V Environment: Operating temperature:0ºC---40ºC Work Humidity:10%---90% Size (L*W*H) 39.4MM*15MM*3MM Software Version VER:2.0 IC RALINK 3070
4: Description of the test parameters Test Project Transmit power EVM Freq Err Receiver Sensitivity Test Data 15.57dbm -30.6dbm 0.03khz -72dbm 5: System Support Platform Operating System CPU Supplier Drive WIN2000/XP/VISTA/WIN7 X86 Platform Support LINUX2.4/2.6 ARM, MIPSII Support WINCE5.0/6.0 ARM ,MIPSII Support 6: Product pin definition TOP Built-in antenna test points DC 5V UDM- UDP+ GND
Bottom 7:Product Size All dimensional tolerances +-0.2MM
RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC ID: X2NBL-LW0XX This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu