BARCO AGM19TKI6 LCD Monitor User Manual 17 18 19TK OEM Medical Rev1 p65

Advan Int'l Corp. LCD Monitor 17 18 19TK OEM Medical Rev1 p65

users manual

AMM17TK/AMM18TK/AMM19TK 1back of the monitorADAVN INTL CORP.2002ELO is a Registered trademark of Elo TouchSystems, Inc.,All other trademarks are the property of their reference owners.This document is subject to change without notice.Advan provides this information as reference only. Reference to other vendors productsdoes not imply any recommendation or endorsement.Revision ControlWARN IN GThe title "WARNING" is used to inform the users ofpossible causes that could inflict the injury, death, orproperty damage to the patients.CAUTIONThe title "CAUTIO N" is used to inform the users ofpossible causes that could inflict the patients althoughit might not severe enough to cause deaths.NOTEThe title "NOTE" is used to inform the users of itemsthat are o f impo rtance in terms of installation,operation, or maintenance of the Equipment althoughthe failure does not inflict the bodily harm to thepatients.Date DescriptionDocument number
FCC Notice NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, user and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. The user manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2 Users GuideTABLE OF CONTENTSQuick Setup................................................................................... 3~5Product Features... 6Unpacking .... 7Symbol Explanations. 8Regulatory Compliance. 8EU Declaration of Conformity for Medical Applications......... 9Screen Position Adjustment... 10Cleaning lnstructions.. 11Supported Modes..... 12Power Management Function 13Power Management System.. 13Connecting the Power Cord.. 14DDC. 14~15Installation. 14~15Installation for Video Play Back.......................................................16User Controls... 17Basic OSD Operation (VGA)... 18~20Basic OSD Screen Section (C-Video or S-Video).... 21~23OSD Function Description (VGA) 24OSD Function Description (C-Video or S-Video)........... 25Troubleshooting 26Specification of AMM17TK......................................................... 27Specification of AMM18TK......................................................... 28Specification of AMM19TK......................................................... 29Connectors... 30Description of Warranty 31~32Tounchscreen Users Manual ... 33~34
AMM17TK/AMM18TK/AMM19TK 3Quick Setup (IBM/IBM Compatible under Windows 95/98/ME/2000)Please Read Carefully When Setting Up Your New MonitorAGM17TK/AGM18TK/AGM19TK Monitor Screen Adjustment and Resolution SettingProcedure for IBM/IBM Compatible Computers with Windows based OS system.Before adjusting the monitor, all the necessary drivers should be installed to your Systemand resolution has to be set to manufacturers recommended preset of 1280 x 1024 @ 60Hz,70Hz, 72Hz or 75 Hz.To check the resolution, press the SELECT UP button on the monitor and the Informationwill display under the OSD. Information will have Resolution, Horizontal and Vertical (Refreshrate) frequency information.To change the resolution to its factory recommended preset.1. On a Windows 95, 98, ME or 2000, press right button on a Mouse to execute the Pop-upmenu.2. Press Properties to execute the Display Properties3. Press Setting and change the resolution to 1280 x 1024.4. Press Apply or OK to select and press OK to keep the selected resolution.5. Go back to Display Properties - Setting - Advanced properties - Adapter6. On Adapter property, change the refresh rate to 60Hz, 70Hz, 72Hz or 75Hz. If you donthave these options, choose Adapter Default. (60Hz recommended)Screen Adjustment Procedure1. Press the AUTO button.2. If you still dont have a clear display monitor, please refer to step 3.3. Start Shut Down in Windows 95/98/ME/2000 - It will display moire on screen4. Press Up or Down button then the OSD menu will pop-up.5. Adjust the Frequency under the OSD to reduce or get rid of the vertical display noise(Jail bars). (Page 16)6. Once the vertical display noise disappears, press adjust the Phase to reduce or get rid ofthe horizontal display noise (Snowy effect). (Page 16)
4 Users GuideQuick Setup (IBM/IBM Compatible under Windows NT 4.0)Please Read Carefully When Setting Up Your New MonitorAGM17TK/AGM18TK/AGM19TK Monitor Screen Adjustment and Resolution SettingProcedure for IBM/IBM Compatible Computers with Windows based OS system.Before adjusting the monitor, all the necessary drivers should be installed to your Systemand resolution has to be set to manufactures recommended preset of 1280 x 1024 @ 60Hz,70Hz, 72Hz or 75Hz.To check the resolution, press the SELECT UP button on the monitor and the Informationwill display under the OSD. Information will have Resolution, Horizontal and Vertical (Refreshrate) frequency information.To change the resolution to its factory recommended preset.1. On a Windows NT 4.0, press right button on a Mouse to execute the Pop-up menu.2. Press Properties to execute the Display Properties3. Press Setting and change the resolution to 1280 x 1024.4. Change Refresh Frequency to 60Hz, 70Hz, 72Hz or 75Hz. (60Hz recommended)Screen Adjustment Procedure1. Press the AUTO button.2. If you still dont have a clear display monitor, please refer to step 3.3. Start Shut Down in Windows 95/98/ME/2000 - It will display moire on screen4. Press Up or Down button then the OSD menu will pop-up.5. Adjust the Frequency under the OSD to reduce or get rid of the vertical display noise(Jail bars). (Page 16)6. Once the vertical display noise disappears, press adjust the Phase to reduce or get rid ofthe horizontal display noise (Snowy effect). (Page 16)
AMM17TK/AMM18TK/AMM19TK 5Quick Setup (Macintosh)Please Read Carefully When Setting Up Your New Monitor1. Set your Macintosh Adapter on pages 23 and 24.2. Push the APPLE icon on the upper left corn and execute Control Panel->Monitors&Sound. Select Thousands for the Color Depth, Select 1280X1024, 60Hz,70Hz, 72Hz or 75Hz for the Resolution. (60Hz recommended)* On some Apple G3 or newer systems, you may not need to use the Macintosh Adapter.Screen Adjustment Procedure1. Press the AUTO button on the monitor.
6 Users GuideINTRODUCTIONCongratulations on your purchasing of the AMM17TK/AMM18TK/AMM19TK highperformance TFT LCD monitor.FEATURESThe AGM17TK/AGM18TK/AGM19TK is a TFT-LCD monitor that is intelligent, microprocessor-based and ergonomically designed display, compatible with most analog RGB (Red, Green,Blue) display standards, including PS/V, PS/2, Apple Macintosh Centris, Quadra, and MacintoshII family signals. The LCD monitor is capable of displaying crisp and vibrant color graphics withVGA, SVGA, XGA, SXGA (non-interlaced), and most Macintosh compatible color video cards.•Advanced Viewing Solution (AVS): Our sophisticated filter extends the viewing angle ofthe screen image, without sacrificing contrast ratio and brightness.•Advanced Timing Setup (ATS): A unique technology from the One Touch Auto Adjustment.Pressing the Auto Adjust button on the front panel, automatically optimizes position,phase, clock, contrast and color balance. This allows the user to maximize the perfectscreen setting in the shortest amount of time.•Advanced Mounting Solution (AMS): Improve flat panel environment, utilizing numerousergonomic mounting solutions to allow creative use in conjunction to product application.•The monitor is able to properly function even in case of upgrade video cards or softwarebecause of the wide auto-scanning compatibility range without requiring to buy a newmonitor.•The internal microprocessor digitally controls auto-scanning. For horizontal scanfrequencies between 24.8 KHz and 60.2 KHz, and vertical scan frequencies between56.3 Hz and 85.1 Hz. In each frequency mode, the microprocessor-based circuitry allowsthe monitor to function at the precision-of a fixed frequency.•The resident memory allows for storing factory default settings and also additional useradjustment parameters.•The maximum resolution achievable is SXGA (1280 x 1024), best suited for Windowsapplications•The compact and sleek cabinet design saves lot of your desk space and makes your desklook neat and tidy.•The monitor is compliant with VESA-DPMS power management standard. In order tosave energy, the monitor must be connected to a system compliant with the standard.•The monitor is also compliant with the most stringent environmental scheme of TCO95. In this scheme, no environmental harmful substances are used during the entiremanufacturing process.The monitor is certified by UL International to medical standard UL2601-1. It is also CEmarked for sale into the European Community for integration or use with medical products. Itis certified by NEMKO according to EN60601-1 & EN60601-1-2 for sale to the medical market.
AMM17TK/AMM18TK/AMM19TK 7UNPACKINGPlease check the following items are present when you unpack the box, and save the packingmaterials in case you will need to ship or transport the monitor in future.•AMM17TK/AMM18TK/AMM19TK LCD Monitor and two video cable (1) VGAHDDB15 cable (1) DVI-D cable•AC Power cord•AC-Adapter•Floppy Disk (for test pattern and set up)•User Manual, Registration Card, and Warranty Card•C-video(Composite Video) Cable, S-Video Cable, Audio Cable and USB CableAUTOSELECTCAUTIONManufacturer : Ault KoreaModel No : MW160 or MW116
8 User TMs Guide Symbol Explanations Indicates proof of conformity to applicable European Economic Community Council directives and to harmonized standards published in the official journal of the European Communities Tested and certified by UL to UL2601. If this mark appears with the indicators "C" and "US" the product is certified for both the U.S and Canadian markets, to the applicable U.S and Canadian standards. Tested to comply with FCC Class B standards. Dangerous high voltage. Consult accompanying documents. Tested and certified by NEMKO in accordance with EN60601-1. Indicates protective earth ground. For indoor use only. DC power control switch Regulatory Compliance This monitor has been tested to comply with IEC/EN 60601-1 and IEC/EN60601-1-2. Only model AGM19TK is classified according to UL2601-1 and CAN/CSA C22.2 No.601-1. Because many medical offices are located in residential areas, this monitor, in addition to the medical requirements, has also been tested and found to comply with the limits for FCC Class B computing devices in a typically configured system. It is the system integrator or configurer's responsibility to test and ensure that the entire system complies with applicable EMC laws.
8.1 User TMs Guide Equipment is not suitable for use in the presence of flammable anesthetic mixture with air or with oxygen or nitrous oxide. No user serviceable parts inside, ask qualified personnel when accessing inside. For disposal of waste product, you must follow the requirement of local code. Electrical input rating : 12V d.c 4.5A Classification - Type of protection against electric shock : Class I Equipment. - Degree of protection against the ingress of water : Ordinary - Mode of operation : Continuous Environmental conditions for transport and storage - Temperature range within 20℃ to 60℃ - Relative humidity range 10% to 90% - Atmospheric pressure range within 500 to 1060hPa. Manufacture information : CARDIANAL INC. 205 Ace Techno Tower, 197-17 Kuro-Dong, Kuro-Gu, Seoul 152-050 Korea Additional explanation of symbol : Direct Current This monitor is intended for use on Health Care Facilities. Only the model AMM17TK, AGM19TK, AMM19TK and 240-030-900 Cleaning : Do not try to clean the LCD Monitor with a liquid or chemicals. This device is complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
AMM17TK/AMM18TK/AMM19TK 9EU Declaration of Conformity for Medical ApplicationsA Declaration of Conformity has been filed for this product. A sample of thisdocument may be found in the addendum which accompanied this manual. For acopy of the Declaration of Conformity document, please contact ADVAN IntlCorp. and request for AMM17TK, AGMM18TK and AMM19TK DOC.InstallationBefore you unpack your monitor, prepare a suitable workspace. You need a stableand level surface near a grounded wall outlet in an area which is relatively free ofglare from sunlight or other sources of bright light. The monitor is cooled by naturalconvection (it has no fan).For optimum performance, do not block the cooling vents.While unpacking the monitor, inspect it and other package contents for shippingdamage that could cause a fire or shock hazard. Immediately report any shippingdamage to the carrier or transportation company and contact customer service formonitor in the future or in case of return.After you unpack the monitor, make sure the following items are included  Monitor with 1.5 meter(5ft)monitor-to computer video cable  AC adapter with cable CAUTION: AC Adapter must be plugged into Grounded a power outlet) CAUTION : AC adapter Manufacturer: Ault korea Model No: MW160 or MW116  Touchscreen cable if monitor has touchscreen option  This operations manual Note: Your system provider may offer alternative cords or cablesdepending on the installation requirement and local geography issues.
10 Users GuideSCREEN POSITION ADJUSTMENTIn order to optimize the best viewing position, you can adjust the tilt of the monitor by usingboth of your hands to hold the edges of the monitor as shown in the figure below. The moni-tor can be adjusted to 28 degrees up as indicated by arrow below.28°
AMM17TK/AMM18TK/AMM19TK 11SAFETY PRECAUTION•Avoid placing the monitor, or any other heavy object, on the power cord to prevent fire orelectrical shock from damage to the power cord.•Do not expose the monitor to rain, excessive moisture, or dust to avoid fire or shock hazard.•Do not cover the slots or openings of the monitor for proper heat dissipation. Always putthe monitor in a place where there is adequate ventilation.•Avoid placing the monitor against a bright background or where sunlight or other lightsources may reflect on the area of the monitor. Place the monitor just below eye level.•Handle with care when transporting the monitor.•Refrain from giving the shock or scratch to the screen, as screen is fragile.
12 User ’s Guide PRESET MODES To reduce the need for adjustment for different modes, the monitor has default setting modes that are most commonly used as given in the table below. If any these display modes are detected, the monitor automatically adjusts the picture size and centering. When none of the mode is matched, the user can store their preferred modes in the user modes. The monitor is capable of storing up to 7 user modes. The only condition to store as a user mode is the new display information must 1 KHz difference for horizontal frequency or 1 Hz for vertical frequency or the sync signal polarities are different from the default modes. Mode Resolution (H×V) H. Freq. (KHz) V. Freq. (Hz) Clock Freq. (MHz) 1 640 ×350 31.5 70 25.175 2 640 ×350 37.9 85 31.5 3 640 ×400 31.5 70 25.175 4 640 ×400 37.9 85 31.5 5 720 ×350 31.5 70 28.322 6 720 ×400 31.5 70 25.175 7 720 ×400 37.9 85 35.5 8 640 ×480 31.5 60 25.175 9 640 ×480 37.9 72 31.5 10 640 ×480 37.5 75 31.5 11 640 ×480 43.3 85 36.0 12 800 ×600 35.1 56 36.0 13 800 ×600 37.9 60 40.0 14 800 ×600 48.1 72 50.0 15 800 ×600 46.9 75 49.5 16 800 ×600 53.7 85 56.25 17 1024 ×768 35.5 43 44.9 18 1024 ×768 48.4 60 65.0 19 1024 ×768 56.5 70 75.0 20 1024 ×768 60 75 78.75 21 1024 ×768 68.7 85 94.5 22 1152 ×864 67.5 75 108.0 23 1280 ×960 60 60 108.0 24 1280 ×1024 63.9 60 135.0 25 1280 ×1024 79 75 157.5
AMM17TK/AMM18TK/AMM19TK 13POWER MANAGEMENT FUNCTIONThe monitor is equipped with the power management function which automatically reduce thepower consumption when not in use in three power level modes.•Stand-by ModeThe monitor goes into stand-by mode when the horizontal sync signal is off for about 10seconds. In this mode, the screen goes off and the power LED blinks for 3 seconds Onand 1 second Off. The screen is displayed after the horizontal sync signal is restored.•Suspend ModeThe monitor goes into suspend mode when the vertical sync signal is off for about 10seconds. The power consumption during this is less than 8 W. In this mode, the screengoes off and the power LED blinks for 3 seconds On and 1 second Off. The screen isdisplayed after the vertical sync signal is restored.•Off ModeThe monitor goes into power-off mode when the vertical and horizontal sync signals areoff for about 10 seconds. In this mode, the screen goes off and the power LED blinks for3 seconds On and 1 second Off. The screen is displayed after the vertical and horizontalsync signals are restored.Power Management SystemThe AMM17TK/18TK/19TK Series Medical Monitor complies with the VESA DPMS powermanagement proposal. The VESA DPMS proposal provides four phases of power-savingmodes by detecting the horizontal sync signal as shown in the table blow.When the monitor is power saving mode or detects an incorrect timing, the screen will beblank and power LED indicator will blink.M ode DC Input Power(monitor only) AC Input power(Incl. AC adapter) LED StatusOn 35 W max. 60 W max. Steady GreenStandby 4.5 W max. 6 W max. Blinking GreenSupend 4.5 W max. 6 W max. Blinking GreenOn 4.5 W max. 6 W max. Blinking Green
14 Users GuideDDCTo make your installation easier, the monitor is able to Plug and Play with your system if yoursystem also supports DDC protocol. The DDC (Display Data Channel) is a communicationprotocol through which the monitor automatically informs the host system about itscapabilities, for example, supported resolutions and corresponding timing. The monitorsupports DDC1 and DDC2B standard.INSTALLATIONTo install the monitor to your host system, please follow the steps as given below:Steps1. Use the VGA cable that provides D-SUB 15P connector and connect to the15-pin connector on the VGA controller card.2. Connect the DC power to the DC power connector on the monitor.3. If use with USB hub, connect the loop cable between the monitor and the USB hub thenconnect the DC power to the bottom of USB hub.4. Connect one end of AC power cord into the AC Adapter and the other end to ACpower outlet. (See page 13)5. Then turn the computer on and then the monitor.6. If the monitor still does not function properly, please refer to the troubleshooting sectionto diagnose the problem.S-Video cableC-Video cableAnalog signal cableDigital signal cable (DVI)USB cable from monitor to PCUSB DC loop cable
AMM17TK/AMM18TK/AMM19TK 15DDCTo make your installation easier, the monitor is able to Plug and Play with your system if yoursystem also supports DDC protocol. The DDC (Display Data Channel) is a communicationprotocol through which the monitor automatically informs the host system about itscapabilities, for example, supported resolutions and corresponding timing. The monitorsupports DDC1 and DDC2B standard.Installation with sound board or sound sourceTo install the monitor for input/output sound, please follow the steps as given below:Steps1. Connect sound source (ex. sound output from sound card, sound output from CD player orDVD player, etc.) to Audio In.2. Connect sound source receiver (ex. sound input or Mic input from the sound card) to Micout.3. At the front of the monitor there are two connection, Audio Out and Mic In. Connect anytype of sound output device (ex. speaker, earphone, etc.) to Audio Out. Mic In is formicrophone input connection.AC power adapterAudio OutMic InAudio in cableMic out cable
16 Users GuideDisplay for Video and Image PlaybackExplains how to use our AGM17TK/AGM18TK to play VCR, view television, video game, ordigital camera images. It also show you how to connect video and other types of videoequipment to the display.Connecting with Video EquipmentYou can connect many types of video equipment to the display. The equipment must haveeither Super VHS video (S-video) ports or composite video ports. To install the monitor toyour video equipment, please follow the steps as given below:Steps1. Make sure the video equipment has a Super VHS (S-video) or a Composite video connector.2. Turn off the computer, display, and video equipment before any types of connection.3. For composite video, plug one end of an RCA cable into the video out port on the videoequipment then connect the other end to the monitor video input port.4. For S-video, plug one end of the S-video cable into the video out port on the video equipmentthen connect the other end to the monitor S-video input port.5. Connect the DC power to the DC power connector on the monitor.6. Connect one end of AC power cord into the AC Adapter and the other end to ACpower outlet.7. Then turn the video equipment on and then the monitor.Connecting to a Television SignalThe display doesnt have a tuner. To view television on the display, you need to use either theVCR or TV tuner card in your computer to change channels.Video and SoundThis monitor does have speakers for sound. If youre using the display to play a video or viewtelevision images, you need to connect the speakers to your television or video equipmentfor sound. Please review page 13 for sound connection.S-Video cableC-Video cableAnalog signal cableDigital signal cable (DVI)USB cable from monitor to PCUSB DC loop cable
AMM17TK/AMM18TK/AMM19TK 17USER CONTROLSFront Panel Controls1. Power LED: Lights up to indicate the power is turned ON.2. Power Switch: To turn ON or OFF the power.3. +: To increase the value of the parameter in the OSD you have selected for adjustment.To increase the brightness directly when OSD menu is not activated.4. -: To decrease the value of the parameter in the OSD you have selected for adjustment.To increase the brightness directly when OSD menu is not activated.5. Select Up: To enter OSD menu then can use as moving upward in the OSD menu.6. Select Down: To move downward in the OSD menu.Switch PC display to Video display and vice versa by one touch when OSD menu is not activated.7. Auto Button: One touch Auto adjust or Exit OSD menu.Standard OSD Operation1. Press menu button to activate the OSD.2. Use Select Up or Down keys to move up or down through the menu. The parameter will be highlighted wehnselected.3. Then use + or - to increase or decrease the value of the parameter, or make selection between different options.4. To quit the OSD screen at any time during the operation, press Auto button. If no keys are pressed for a time period,the OSD automatically disappears.
18 Users GuideOSD Scren Basic Section (VGA)For OSD display, push Menu. For selecting Icon, push Upor DownPush the select button to execute the AutoSetup functionPush Up or Down button to select betweenBrightness or Contrast then push SelectUse Left or Right button to adjustPush Up or Down button to select betweenFrequency or Phase then push SelectUse Left or Right button to adjustPush Up or Down button to select betweenHorizontal or Vertical then push SelectUse Left or Right button to adjustPush Up or Down button to select betweenOSD Hor. Pos., OSD Ver. Pos., OSDBackground, or User Timeout then push SelectUse Left or Right button to adjustPush Left or Right to select Color Temp between5000, 6500, 7300, 9500, or User then pushSelectIf User were slected, push Up or Down button toselect between Red, Green, or Blue then pushSelectUse Left or Right button to adjust
AMM17TK/AMM18TK/AMM19TK 19Push Up or Down button to select betweenDPMS, Auto Source Select, Freeze Frame, orADC Calibration then push SelectUse Left or Right button to adjustPush the select button to execute the ZoomfunctionPush the select buttonUse Left or Right button to adjustPush Up or Down button to select between 640Mode or 720 ModeUse Left or Right to choose the correct mode thenpush Select buttonPush Up or Down button to select betweenAnalog RGB, Digital RGB, Composite Video orSuper VideoUse Left or Right to choose the correct mode thenpush Select buttonOSD Scren Basic Section (VGA)For OSD display, push Menu. For selecting Icon, push Upor DownPush the select buttonUse Left or Right button to adjust
20 Users GuidePush the select button to execute RecallFactory DefaultPush the select button to execute InformationOSD Scren Basic Section (VGA)For OSD display, push Menu. For selecting Icon, push Upor Down
AMM17TK/AMM18TK/AMM19TK 21OSD Scren Basic Section (C-Video or S-Video)Push Up or Down button to select betweenHorizontal or Vertical then push SelectUse Left or Right button to adjustPush Up or Down button to select betweenBrightness or Contrast then push SelectUse Left or Right button to adjustPush Up or Down button to select betweenOSD Hor. Pos., OSD Ver. Pos., OSDBackground, or User Timeout then push SelectUse Left or Right button to adjustPush Left or Right to select Color Temp between5000, 6500, 7300, 9500, or User then pushSelectIf User were slected, push Up or Down button toselect between Red, Green, or Blue then pushSelectUse Left or Right button to adjustPush Select buttonPush Left or Right button to adjustPush Select buttonPush Left or Right button to adjustFor OSD display, push Menu. For selecting Icon, push Upor Down
22 Users GuidePush Up or Down button to select betweenAnalog RGB, Digital RGB, Composite Video orSuper VideoUse Left or Right to choose the correct mode thenpush Select buttonPush the select buttonUse Left or Right button to adjustPush the select buttonUse Left or Right button to adjustPush the select buttonUse Left or Right button to adjustPush the select buttonUse Left or Right button to adjustPush Up or Down button to select betweenDPMS, Auto Source Select, Freeze Frame, orADC Calibration then push SelectUse Left or Right button to adjustOSD Scren Basic Section (C-Video or S-Video)For OSD display, push Menu. For selecting Icon, push Upor Down
AMM17TK/AMM18TK/AMM19TK 23Push the select button to execute RecallFactory DefaultPush the select button to execute InformationOSD Scren Basic Section (C-Video or S-Video)For OSD display, push Menu. For selecting Icon, push Upor Down
24 Users GuidemetInoitpircseDnoitcnuFtsujdAotuA -H,noitisoP-VtsujdayllacitamotualliwtsujdA-otuAehT,kcolC,noitisoP5tuobasekatssecorpelohweht,tsartnoCdna,esahP-kcolCdehcattaehtnielifnrettaptsetehtesuesaelP(.sdnoces.)tsujdAotuArofksidytiliturotinomDCLssenthgirB.ssenthgirbehtesaercedroesaercnioTtsartnoC.tsartnocehtesaercedroesaercnioTleveLkcalB.levelkcalbehtesaercedroesaercnioTycneuqerF.)kcolctod(ycneuqerftsujdaoTesahP.)esahp-kcolc(esahptsujdaoTlatnoziroH.thgirrotfelneercsehtevomoTlacitreV.drawnwodrodrawpuneercsehtevomoTsoProHDSO.thgirrotfelunemDSOevomoTsoPreVDSO.drawnwodrodrawpuunemDSOevomoTdnuorgkcaBDSO.tneculsnarTroeuqapOneewtebesoohCtuoemiTresU.emitgniraeppaneercsDSOteSpmeTroloC rolocrofresUro,0059,0037,0056,0005neewtebesoohC.pmetdeR.deRecnalaBneerG.neerGecnalaBeulB.eulBecnalaBSMPD.SMPDelbasiDroelbanEecruoSotuAtceleS.thgihro,wol,ffoneewtebtcelesecruosotuatsujdAemarFezeerFemarfezeerfelbasiDroelbanEnoitarbilaCCDAmooZnoitcnufni-moozelbanEssenprahSegamI.5ot1morfssenprahsegamiteSedoMelacS ro,oitartcepsa,neercsllifneewtebedomelacsesoohCenootenoedoMSOD.027ro046taedomSODrednuyalpsidteSecruoStupnItceleS,BGRlatigid,BGRgolananeewtebecruostupniesoohCoedivrepusro,oedivetisopmocyrotcaFllaceRtluafeD.tluafedyrotcafotteSnoitamofnI tupnidna,etarhserfer,noitulosernonoitamrofniyalpsiD.edomOSD Function Description (Under VGA Display)
AMM17TK/AMM18TK/AMM19TK 25OSD Function Description (Under C-Video or S-Video Display)metInoitpircseDnoitcnuFeuH.leveleuhehtesaercedroesaercnioTnoitarutaS.levelnoitarutasehtesaercedroesaercnioTssenthgirB.ssenthgirbehtesaercedroesaercnioTtsartnoC.tsartnocehtesaercedroesaercnioTleveLkcalB.levelkcalbehtesaercedroesaercnioTlatnoziroH.thgirrotfelneercsehtevomoTlacitreV.drawnwodrodrawpuneercsehtevomoTsoProHDSO.thgirrotfelunemDSOevomoTsoPreVDSO.drawnwodrodrawpuunemDSOevomoTdnuorgkcaBDSO.tneculsnarTroeuqapOneewtebesoohCtuoemiTresU.emitgniraeppaneercsDSOteSpmeTroloC rolocrofresUro,0059,0037,0056,0005neewtebesoohC.pmetdeR.deRecnalaBneerG.neerGecnalaBeulB.eulBecnalaBSMPD.SMPDelbasiDroelbanEecruoSotuAtceleS.thgihro,wol,ffoneewtebtcelesecruosotuatsujdAemarFezeerF.emarfezeerfelbasiDroelbanEnoitarbilaCCDAmooZ.noitcnufni-moozelbanEssenprahSegamI.5ot1morfssenprahsegamiteSelacSoediVedoM,edomelacs3:4,lamronneewtebedomelacsoedivesoohC.edomelacs9:61rossenprahSoediV.ssenprahsoedivehtesaercedroesaercnioTecruoStupnItceleS,BGRlatigid,BGRgolananeewtebecruostupniesoohCoedivrepusro,oedivetisopmocyrotcaFllaceRtluafeD.tluafedyrotcafotteSnoitamofnI tupnidna,etarhserfer,noitulosernonoitamrofniyalpsiD.edom
26 Users GuideTROUBLESHOOTINGBefore sending your LCD monitor for servicing, please check the troubleshooting list belowto see if you can self-diagnose the problem.smelborPsutatStnerruCydemeRoNerutciPNODEL•ottsartnocdnassenthgirbtsujda,DSOgnisU.sgnittestluafedriehtotteserromumixamFFODEL•.hctiwsrewopehtkcehC•ylreporpsidrocrewopCAfikcehC.retpadaCAehtotdetcennocgniknilBDEL•ylreporpsielbaclangisoedivfikcehC.rotinomfokcabehttadetcennoc•.NOsimetsysretupmocotrewopehtfikcehClamronbAerutciPerutciPelbatsnU•retpadascihpargfonoitacificepsehtfikcehCebyamhcihwecnailpmocnisirotinomdna.hctamsimycneuqerflangistupniehtgnisuacsiyalpsiDretnec,gnissimllamsootro,tfihsniegralootroezisyalpsid•yalpsidllitsfi,nottubputeSotuAgnisU,KCOLCtsujdanehterutciplamronba-VdnaNOITISOP-H,ESAHP-KCOLC.slangisdradnats-nonhtiwNOITISOP•neercs-llufgnissimfoesacni,DSOgnisUruoyninoituloserrehtotcelesesaelp,egamiro)TN,89/59swodniW(metsySgnitarepO.gnimithserferlacitrevrehto•gnitsujdaretfasdnoceswefaroftiawtsuMrognignahcerofebegamiehtfoezisehtehtFFOgnirewoprolangisehtgnitcennocsid.rotinom
AMM17TK/AMM18TK/AMM19TK 27SPECIFICATION* All contents are subject to change without notice.* Touch Screen Model doesnt include the Video-in (C-Video, S-Video) function.* Surface Wave Touchscreen model AMM17TK/18TK/19TK-TEW and Resistive Touchscreen modelAMM17TK/18TK/19TK-TEAM M 17TKLC D Panel 44.2cm/17.4-inch C olor TFT PanelType A ctive M atrixResolution 1280 dots x 1024 lines (Recommended)Pixel Pitch 0.27mmD isp la y C o lo r 1 6 m illio n c o lo r sResponse Time 25msC olor Tone U p to 256 toneC olor Filter RG B vertical stripe typeFace Finishing Anti-Glare Hard C oatedViewing Angle 160°H 160°V (CR>=10)Video 0.7Vp-p analog RGB & TM DS (PanelLink) Digital165 MHz x 1Input SignalSync 2.5~5.0Vp-p separated syncInput Impedance (Analog) Video - 75 OhmSync - 1k OhmComposite Sync C-Video, S-VideoDigital 3 channel TM DS receiver, single pixel 24 bit M S B-aligned RGB TFTScanning FrequencyHorizontal 30~68kHzVertical 56~85Hz (UP to 85Hz at 1024 x 768 mode and up to75Hz at 1280 x 1024)Display SizeH x V 13.6" x 10.9" (345.0mm x 276.48mm)Brightness, Contrast R adtio, Gray ScalesBrightness 220 cd/m2, StandardContrast Ratio 400:1 Typ.Gray Scales Up to 256 stepsSignal Input ConnectorVideo DB9-15pin, Digital DVI, N TSC, S-VideoTouchscreen RS-232 DB-9 (Optional)Temperature EnvironmentOperating Temperature 32° ~ 104°F (0° - 35°C)Storage Temperature -4° ~ 140°F (20° - 60°C)Humidity 10 ~ 90%RH (without condensation)Power SourceDisplay M onitor DC 12VAC-Adapter AC100~240V 60W (Without option, NormalOperation)RegulationsSafety and EM C UL/cUL, FCC, CE, TCO 99, Energy Star, CB, MPRII, ERG/GS.VCCI, UL2601-1, EN60601-1CabinetDesktop Stand 17.5inch (W ) x 17.8inch (H) x 9.5inch (D)450mm (W ) x 455mm (H) x 245mm (D)Free Mount 17.5inch (W ) x 14.25inch (H) x 3inch (D)450mm (W ) x 362mm (H) x 76mm (D)WeightDesktop Stand 20.6 lb. (9.3K g)Free M ount 16 lb. (7.3K g)Tilt B as e5° Down 30° UpStereo speaker, USB (Rev 1.0)Optional M oduleTouch Panel
28 Users GuideSPECIFICATIONAM M 18TKLCD Panel 46cm/18.1-inch Color TFT PaneType A ctive M atrixResolution 1280 dots x 1024 lines (Recommended)Pixel Pitch 0.28mmD isp lay C o lo r 1 6 m illio n c o lo rsResponse Time 40msC olor Tone Up to 256 toneColor Filter RGB vertical stripe typeFace Finishing Anti-Glare Hard C oatedViewing Angle 160°H 160°V (CR>=10)Video 0.7Vp-p analog RGB & TM DS (PanelLink) Digital165 MHz x 1Input SignalSync 2.5~5.0Vp-p separated syncInput Impedance (Analog) Video - 75 OhmSync - 1k OhmComposite Sync C-Video, S-VideoDigital 3 channel TM DS receiver, single pixel 24 bit M SB-aligned RGB TFTScanning FrequencyHorizontal 30~68kHzVertical 56~85Hz (UP to 85Hz at 1024 x 768 mode and up to75Hz at 1280 x 1024)Display SizeH x V 14.13" x 11.3" (359mm x 287mm)Brightness, Contrast Radtio, Gray ScalesBrightness 200 cd/m2, StandardContrast Ratio 250:1 Typ.Gray Scales Up to 256 stepsSignal Input ConnectorVideo DB9-15pin, Digital DVI, NTSC, S-VideoTouchscreen RS-232 DB-9 (Optional)Temperature EnvironmentO perating Temperature 41° ~ 95°F (5° - 35°C)Storage Temperature -4° ~ 140°F (20° - 60°C )Humidity 10 ~ 90%RH (without condensation)Power SourceDisplay M onitor DC 12VAC-Adapter AC100~240V 27W (Without option, NormalOperation)RegulationsSafety and EM C UL/cUL, FCC, CE, TCO99, Energy Star, CB, MPRII, ERG/GS.VCCI, UL2601-1, EN60601-1CabinetDesktop Stand 17.5inch (W ) x 17.8inch (H) x 9.5inch (D)Free Mount 17.5inch (W ) x 14.25inch (H) x 3inch (D)WeightDesktop Stand 22.8 lb. (10.4Kg)Free M ount 18.1 lb. (8.2K g)Tilt B ase0° Down 28° UpStereo speaker, USB (Rev 1.0)Optional M oduleTouch Panel* All contents are subject to change without notice.* Touch Screen Model doesnt include the Video-in (C-Video, S-Video) function.* Surface Wave Touchscreen model AMM17TK/18TK/19TK-TEW and Resistive Touchscreen modelAMM17TK/18TK/19TK-TE
AMM17TK/AMM18TK/AMM19TK 29SPECIFICATIONAM M 19TKLCD Panel 48cm/19-inch Color TFT PaneType A ctive M atrixResolution 1280 dots x 1024 lines (Recommended)Pixel Pitch 0.294mmD isp lay C o lo r 1 6 m illio n c o lo rsResponse Time 25msC olor Tone Up to 256 toneColor Filter RGB vertical stripe typeFace Finishing Anti-Glare Hard C oatedViewing Angle 170°H 170°V (CR>=10)Video 0.7Vp-p analog RGB & TM DS (PanelLink) Digital165 MHz x 1Input SignalSync 2.5~5.0Vp-p separated syncInput Impedance (Analog) Video - 75 OhmSync - 1k OhmComposite Sync C-Video, S-VideoDigital 3 channel TM DS receiver, single pixel 24 bit M SB-aligned RGB TFTScanning FrequencyHorizontal 30~68kHzVertical 56~85Hz (UP to 85Hz at 1024 x 768 mode and up to75Hz at 1280 x 1024)Display SizeH x V 14.8" x 11.9" (376mm x 301mm)Brightness, Contrast Radtio, Gray ScalesBrightness 250 cd/m2, StandardContrast Ratio 500:1 Typ.Gray Scales Up to 256 stepsSignal Input ConnectorVideo DB9-15pin, Digital DVI, NTSC, S-VideoTouchscreen RS-232 DB-9 (Optional)Temperature EnvironmentO perating Temperature 41° ~ 95°F (5° - 35°C)Storage Temperature -4° ~ 140°F (20° - 60°C )Humidity 10 ~ 90%RH (without condensation)Power SourceDisplay M onitor DC 12VAC-Adapter AC100~240V 27W (Without option, NormalOperation)RegulationsSafety and EM C UL/cUL, FCC, CE, TCO99, Energy Star, CB, MPRII, ERG/GS.VCCI, UL2601-1, EN60601-1CabinetDesktop Stand 17.5inch (W ) x 17.8inch (H) x 9.5inch (D)Free Mount 17.5inch (W ) x 14.25inch (H) x 3inch (D)WeightDesktop Stand 22.8 lb. (10.4Kg)Free M ount 18.2 lb. (8.3K g)Tilt B ase0° Down 28° UpStereo speaker, USB (Rev 1.0)Optional M oduleTouch Panel* All contents are subject to change without notice.* Touch Screen Model doesnt include the Video-in (C-Video, S-Video) function.* Surface Wave Touchscreen model AMM17TK/18TK/19TK-TEW and Resistive Touchscreen modelAMM17TK/18TK/19TK-TE
30 Users GuideConnectorsDC InputConnector Jack Power InputThe SCD-014-1-A (SHIUA CHYUAN) or equivalent.Video Input15 pin D-subminiature connector.The vedor P/N is DHSB-15 FRF7(LEOCO) or equivalent.Touch Port9Pin D-subminiature connector.24 pin DVI-D connector.DDWG or equivalent connector.Pin Description1 +12V DC2 GNDPin Signal Assignment Pin Signal Assignment Pin Signal Assignment1 T.M .D.S. Data2- 9 T.M .D .S . Data1- 17 T.M .D .S. Data0-2 T.M .D.S. Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+3 T.M .D .S . D ata2 /4S h ie ld11 T.M.D.S. Data1/3Shield19 T.M.D.S. Data0/5S hie ld4 T.M .D.S. Data4- 12 T.M.D.S. Data3- 20 T.M.D.S. Data5-5 T.M .D.S. Data4+ 13 T.M.D.S. Data3+ 22 T.M.D.S. Data5+6 DD C Clock 14 +5V Pow er 22 T.M .D .S. C lockS hie ld7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock+8 No Connect 16 Hot Plug Detect 24 T.M.D.S. Clock-D e s c rip tio n P in D e s c rip tio n P inRed Video 1 N C 9Green Video 2 VGA Con 10Blue Video 3 N C 11N C 4 SDA (DDC 1/2) 12Logic G round 5 H -sync 13Red Video Ground 6 V-sync 14Green Video Ground 7 SC L (DDC 2B) 15Blue Video Ground 8D escription Pin D escription PinDCD 1 DSR 6RXD 2 RTS 7TXD 3 C TS 8DTR 4 RIN C 9LogicGround 5
AMM17TK/AMM18TK/AMM19TK 31Description of WarrantyAdvan warrants that the goods the goods sold hereunder will be free of defects in materialsand workmanship, and such goods will substantially conform to the specifications furnishedby Advan, and to any drawings or specifications furnished to Advan by the Buyer ifapproved by Advan. This warranty shall be effective only if Advan receives notice of suchdefect or nonconformance during the period of the warranty. Advan sole and exclusive theAdvan product(s) with refurbished units provide a credit to buyer in the amount of thepurchaseprice.Commencement and Duration of WarrantyThe warranty period begins on the date of shipment from Advan. The goods sold hereunderare warranted for a period of three years (36 months) from date of shipment unless otherwiseagreed to by Buyer and Advan. No extension of the warranty will be given during the timethe goods are in Advan possession.Place of Repair or ReplacementIn order to obtain service under this warranty, Buyer must notify Advan of the defect beforeexpiration on the warranty period, and request a Return Material Authorization Number. Ifthe configuration has been modified in any manner, the product must be returned to itsoriginal configuration before any warranty service will be perfomed by Advan. No goods areto be returned to Advan without prior authorization. Buyer will be responsible for packagingand shipping the defective goods to the Advan Service Facility with shipping chargesprepaid.Limitation of WarrantyMonitor:For three years (36 months) after the date of purchase, ADVAN or its Authorized ServiceCenters, will repair or replace if defective in material or workmanship. This Limited Warrantydoes not include cleaning, or damage caused by accident, neglect, misuse or improper installationor operation, any damage caused from service, maintenance, modifications or tampering byanyone other than an ADVAN Authorized Service Representative, or by the use of supplies,consumable items and conditions beyond the control of ADVAN, such as common carrierprovided equipment and/or facilities, operation of ADVAN product in excess of the specificationsor with the Serial Number or Rating label removed.*Touch Screen:For one year after the date of purchase, ADVAN or its Authorized Service Centers, will repairor replace if defective in material or workmanship. This Limited Warranty does not includecleaning, or damage caused by accident, neglect, misuse or improper installation or opera-tion, any damage caused from service, maintenance, modifications or tampering by anyoneother than an ADVAN Authorized Service Representative, or by the use of supplies, consum-able items and conditions beyond the control of ADVAN, such as common carrier providedequipment and/or facilities, operation of ADVAN product in excess of the specifications orwith the Serial Number or Rating label removed.
32 Users GuideADVAN DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING,WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY ORFITNESS FOR PARTICULAR PURPOSE, EXCEPT TO THE EXTENT THAT ANY WARRAN-TIES IMPLIED BY LAW CANNOT BE VALIDLY WAIVED.No oral or written information or advice given by ADVAN, its authorized service center,distributors, dealers, agents or employees, shall create another warranty or modify thiswarranty. This warranty states ADVANs entire liability and your exclusive remedy againstADVAN for any failure of the ADVANs product to operate properly.Neither ADVAN nor anyone else involved in the development, production, or delivery of thisproduct shall be liable for any indirect, incidental, special consequential, exemplary, orpunitive damages, including lost profits, arising from the use of or inability to consequentialor incidental damages, the above limitation may not apply to you.This Limited Warranty gives you special legal rights and you may also have other right,which vary from State to State.InstallationAdvan makes no warranty with respect to any installation of Advans product(s)by Advan, any authorized dealer, or any other person.Technical AssistanceFor technical assistance please call (510)490-1005 between 8:00 a.m. and 5:00 p.m. PST,Monday through Friday or email to support@mail.advancorp.com with a description of yourtechnical issues.ServiceIf your Medical Monitor needs service, call Advan Customer Service at(510)490-1005 between 7:00 a.m and 4:00 p.m PST, Monday throughFriday or fax to (510)490-1151. You will need the units serial number and abrief description of the problem and where unit were purchased to receive a RMA number.If a service is required please return the product for service using the original shippingcontainer with the RMA number included in package on the outside of the box.In order to protect ADVAN employees form potential health hazards, ADVAN requires thatthe RMA product be disinfected before returning to ADVAN for service. Any product notcleaned prior to shipment will be returned to the customer.In-transit damage is not covered by warranty. We suggest you always insure your shipment.Advan will only pay for the return shipment by surface transportation. It is the responsibilityof the sender to prepay transportation charges.Note: Returns will not be accepted without an assigned RMA number.
AMM17TK/AMM18TK/AMM19TK 33Tounchscreen User's Manual (AMM17TK-TE/AMM18TK-TE/AMM19TE or AMM17TK-TEW/AMM18TK-TEW/AMM19TK-TEW)Quick Start1.Connect Power Code and VGA Cable of LCD Monitor.2.Connect Touchscreen DB9 male RS-232 cable.3.Turn the LCD display Power ON.4.Adjust the tilt of LCD Monitor.5.Adjust the Picture of LCD Monitor.6.Install driver software of Touchscreen (See "Driver software" for details).7.Adjust the calibration of Touchscreen (See "Driver software" for details).IntroductionThe ELO IntelliTouch Touchscreen system consists of a touchscreen and anelectronic touchscreen controller. The touchscreen may be a flat, spherical, orcylindrical and is installed over the face of the LCD. The touchscreen controllerinstalled inside of theLCD.The IntelliTouch TouchscreenThe IntelliTouch surface wave touchscreen consists of a glass panel molded to theprecise shape of a display's face. A scratch-resistant, hard-coated plastic coversheet may be clear for best image clarity or have an antiglare finish.The IntelliTouch ControllerThe IntelliTouch controllers provide the drive signal for touchscreen, convert thereceived analogue signals into digital touch coordinates, and send thesecoordinates to the computer.
34 Users GuideTouchmonitor installationCable Connection1. Connect and test LCD as a video display only.2. Plug the DB9 male into the DB9 female connector labled "TOUCHSCREEN"on the back of the LCD Monitor.Driver softwareELO provide driver programs for the DOS, Windows 3.1, Windows 95/98,Windows NT, Windows 2000, Windows XP, OS/2, and Macintosh systems.Additional drivers may be available for other system. Contact ELO for details.Installing Driver software for Windows / Windows NT1. Shutdown Windows or Windows NT and turn off your computer.2. Install touchscreen hardware as described in the "Quick start" or "Touchmonitorinstallation".3. Start your computer.4. Insert the Windows or Windows NT driver disk into diver A or B.5. Browse for "setup.exe" in the directory to which you extracted the driver files.6. Type "setup.exe" in the space provided and press Enter.7. The touchscreen setup wizard will appear. You will need to select serial port,type of touchscreen controller, and language.8. Complete the setup program.9. Shutdown and restart windows NT.10. Click the start button, then click control panel.11. Double-click touchscreen control panel.12. Click the calibrate button and touch each of the three targets as they appearon the screen.Contacting ELOwww.elotouch.comELO Touchsystems INC.6500 Kaiser Drive Fremont,CA 94554 USA
AMM17TK/AMM18TK/AMM19TK 35

Navigation menu